I88Z5SPM93825G Wireless Card

FCC Statement Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. The device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The user’s manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generate, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is needed. Consult the dealer or an experienced radio/TV technician for help. CAUTION: To comply with FCC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter This device is intended only for OEM integrators under the following conditions: The antenna must be installed such that 20 cm is maintained between the antenna and users. For laptop installations, the antenna must be installed to ensure that the proper spacing is maintained in the event the users places the device in their lap during use (i.e. positioning of antennas must be placed in the upper portion of the LCD panel only to ensure 20 cm will be maintained if the user places the device in their lap for use) and The transmitter module may not be co-located with any other transmitter or antenna. As long as the 2 conditions above are met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE: In the event that these conditions can not be meet (for example certain laptop configurations or co- location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in devices where the antenna may be installed such that 20 cm may be maintained between the antenna and users (for example access points, routers, wireless ASDL modems, certain laptop configurations, and similar equipment). The final end product must be labeled in a visible area with the following: "Contains WLAN PC Module TX FCC ID: I88Z5SPM9382”. RF Exposure Manual Information That Must be Included The users manual for end users must include the following information in a prominent location "IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter." Additional Information That Must be Provided to OEM Integrators The end user should NOT be provided any instructions on how to remove or install the device. 1. Introduction IEEE802.11a/n Wireless Network Mini PCI Express Card is the perfect solution for your wireless network applications based on the IEEE 802.11a/n standard offering a data rate of 300Mbps in a wireless LAN environment. Z5SPM9382 is designed for Access Point, Router, ATUR, Printer Server series, IP Camera series and Internet Video Server gives you wireless access the web and network resource without the wire. With Direct Spread Spectrum Signaling (DSSS) and Orthogonal Frequency Division Multiplexing (OFDM), domain access control, and group security, the modules will safeguard all your wireless data transmissions from your nosy neighbors. Z5SPM9382 allows you to take full advantage of your devices mobility with access to real-time information and online services anytime and anywhere. 2. Feature . Complies with IEEE 802.11a/n Standard for Wireless LAN. . Works with All Existing Network Infrastructures. . Compatible with Wi-Fi Wireless Products and Services. . Freedom to Roam While staying Connected. . Delivers data rate up to 300 Mbps. . Two UF-L Connectors for External Antenna . . Lower Power Consumption. 3. Hardware Installation The following sections in this chapter describe how to install Z5SPM9382 Module. 3.1. Installation Overview Z5SPM9382 wireless module is design for Access Point, Router, ATU-R, Printer Server series, IP Camera series and Internet Video Server only. 3.2. Safety Recommendations The safety guidelines are as follows: -Keep the board area clear and dust-free before, during, and after installation. -K…

Text truncated - open the document above for the full version.

FCC ID: I88Z5SPM9382 Report No.: RF 130605C26 Modular Approval Request Letter Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch August 5, 2013 Dear Application Examiner, ZyXEL Communications Corporation, FCC ID: I88Z5SPM9382 would like to have your authorization as a modular approval specific to the mobile RF exposure condition. The requirements of Public Notice DA00-1407 have been met and shown on the following statements. 1. “The modular transmitter must have its own RF shielding.” The radio portion of this module has been shielded, please see exhibition External Photo. 2. “The modular transmitter must have buffered modulation/data inputs.” The EUT has buffered data inputs, it is integrated in chip AR9382. 3. “The modular transmitter must have its own power supply regulation.” The part number of this regulator is AR9382. 4. “The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(C).” The EUT meets the FCC antenna requirements. The spurious emission, unique antenna connector and photo of antennas are shown in the test report. 5. “The modular transmitter must be tested in a stand-alone configuration” The EUT was tested in a stand-alone configuration via a USB extender. Please see section Photographs of Test Configuration in the test report, the EUT was plugged in this extender. 6. “The modular transmitter must be labeled with its own FCC ID number.” Please see exhibition Label Sample for the FCC ID of this module. And also in the exhibition Users Manual, there are instructions give to the OEM on how to label the end product. FCC ID: I88Z5SPM9382 Report No.: RF 130605C26 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.” The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are given in the Users Manual. 8. “The modular transmitter must comply with any applicable RF exposure requirements.” The EUT is compliant with all applicable RF exposure requirements. RF Exposure is addressed in the RF exposure exhibition. Please contact me if you have any further questions. Thanks for your attention. Best Regards, Robert Huang Senior Engineer Bureau Veritas Consumer Products Services (H.K.) Ltd., Hsinchu Branch

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2

Label location

Models Name/Part Name/ Artwork Number/ Artwork Rev./ Unit:mm SPEC LABEL 01 PANTONE WHITE Diecut display only Designed/Date/ PANTONE BLACK Camille Liu NET9-432400 UAG4100-R (5G) DELTA NETWORKS, INC. THESE DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF DELTA NETWORKS. AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SELL OF APPARATUSES OR DEVICES WITHOUT PERMISSION . Graphic Layout Scale/ 1:1 Colors Printed/ Dimensions/ WIDTH HEIGHT 32mm x 8 mm NOTE: 1. Font: Arial, 6pt Model name: Z5SPM9382 FCC ID: I88Z5SPM9382 CCXXxxYYyyyZzW

Page 3 Page 4 Page 5

FCC ID: I88Z5SPM9382 Report No.: RF130605C26 Operational Description This device is a 5G Wireless Card, which operates in 5GHz; the maximum data rate could be up to 300Mbps which OFDM technique. If the signal to noise radio is too poor which could not support 300Mbps, the 6Mbps data rate with OFDM technique will be applied. The transmitter of the EUT is powered by 5Vdc from power supply. The antenna is Omini-directional dipole antenna with Reverse SMA plug antenna connector. The other instruction, please have a look at the user’s manual. FCC 15.407(c) states: The device shall automatically discontinue transmission in case of either absence of information to transmit or operational failure. These provisions are not intended to preclude the transmission of control or signaling information or the use of repetitive codes used by certain digital technologies to complete frame or burst intervals. Applicants shall include in their application for equipment authorization a description of how this requirement is met” Data transmission is always initiated by software, which is then pass down through the MAC, through the digital and analog baseband, and finally to the RF chip. Several special packets (ACKs, CTS, PSPoll, etc...) are initiated by the MAC. There are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only while one of the aforementioned packets are being transmitted.

Report No.: SA130605C26 1 of 5 Report Format Version 5.0.0 RF EXPOSURE REPORT REPORT NO.: SA130605C26 MODEL NO.: Z5SPM9382 FCC ID: I88Z5SPM9382 RECEIVED: May 23, 2013 TESTED: Jun. 19 ~ Jun. 28, 2013 ISSUED: Jul. 05, 2013 APPLICANT: ZyXEL Communications Corporation ADDRESS: No. 2, Gongye E. 9th Road Hsinchu Science Park, Hsinchu, Taiwan ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-com pliance to the specification. Report No.: SA130605C26 2 of 5 Report Format Version 5.0.0 TABLE OF CONTENTS RELEASE CONTROL RECORD ................................................................................................ 3 1. CERTIFICATION ............................................................................................................ 4 2. RF EXPOSURE .............................................................................................................. 5 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) ........................................ 5 2.2 MPE CALCULATION FORMULA ................................................................................... 5 2.3 CLASSIFICATION .......................................................................................................... 5 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER ................................. 5 Report No.: SA130605C26 3 of 5 Report Format Version 5.0.0 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA130605C26 Original release Jul. 05, 2013 Report No.: SA130605C26 4 of 5 Report Format Version 5.0.0 1. CERTIFICATION PRODUCT: 5G Wireless Card MODEL NO.: Z5SPM9382 BRAND: ZyXEL APPLICANT: ZyXEL Communications Corporation TESTED: Jun. 19 ~ Jun. 28, 2013 TEST SAMPLE: ENGINEERING SAMPLE STANDARDS: FCC Part 2 (Section 2.1091) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 The above equipment (model: Z5SPM9382) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE :Jul. 05, 2013 Pettie Chen / Senior Specialist APPROVED BY : , DATE :Jul. 05, 2013 Ken Liu / Senior Manager Report No.: SA130605C26 5 of 5 Report Format Version 5.0.0 2. RF EXPOSURE 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY (mW/cm 2 ) AVERAGE TIME (minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 2.2 MPE calculation Formula Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm 2.3 Classification The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. 2.4 Calculation result of maximum conducted power FREQUENCY BAND (MHz) MAX POWER (dBm) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/cm 2 ) LIMIT (mW/cm 2 ) 5180-5240 16.61 3 20 0.018 1 5745-5825 25.78 3 20 0.150 1

Report No.: RF130605C26 1 of 46 Report Format Version 5.2.0 FCC TEST REPORT REPORT NO.: RF130605C26 MODEL NO.: Z5SPM9382 FCC ID: I88Z5SPM9382 RECEIVED: May 23, 2013 TESTED: Jun. 19 ~ Jun. 28, 2013 ISSUED: Jul. 05, 2013 APPLICANT: ZyXEL Communications Corporation ADDRESS: No. 2, Gongye E. 9th Road Hsinchu Science Park, Hsinchu, Taiwan ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-com pliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF130605C26 2 of 46 Report Format Version 5.2.0 TABLE OF CONTENTS RELEASE CONTROL RECORD ................................................................................................................ 4 1. CERTIFICATION ............................................................................................................................ 5 2. SUMMARY OF TEST RESULTS ................................................................................................... 6 2.1 MEASUREMENT UNCERTAINTY ................................................................................................ 6 3. GENERAL INFORMATION ............................................................................................................ 7 3.1 GENERAL DESCRIPTION OF EUT .............................................................................................. 7 3.2 DESCRIPTION OF TEST MODES ................................................................................................ 8 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ................................................ 9 3.3 DESCRIPTION OF SUPPORT UNITS ........................................................................................ 11 3.3.1 CONFIGURATION OF SYSTEM UNDER TEST ......................................................................... 11 3.4 GENERAL DESCRIPTION OF APPLIED STANDARDS ............................................................. 12 4. TEST TYPES AND RESULTS ..................................................................................................... 13 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT ..................................................... 13 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT ................................... 13 4.1.2 TEST INSTRUMENTS ................................................................................................................. 14 4.1.3 TEST PROCEDURES ................................................................................................................. 15 4.1.4 DEVIATION FROM TEST STANDARD ....................................................................................... 15 4.1.5 TEST SETUP ............................................................................................................................... 16 4.1.6 EUT OPERATING CONDITIONS ................................................................................................ 16 4.1.7 TEST RESULTS .......................................................................................................................... 17 4.2 CONDUCTED EMISSION MEASUREMENT .............................................................................. 26 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ........................................................... 26 4.2.2 TEST INSTRUMENTS ................................................................................................................. 26 4.2.3 TEST PROCEDURES ................................................................................................................. 27 4.2.4 DEVIATION FROM TEST STANDARD ....................................................................................... 27 4.2.5 TEST SETUP ............................................................................................................................... 27 4.2.6 EUT OPERATING CONDITIONS ................................................................................................ 27 4.2.7 TEST RESULTS .......................................................................................................................... 28 4.3 6dB BANDWIDTH MEASUREMENT .......................................................................................... 30 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT ........................................................................ 30 4.3.2 TEST SETUP ...................................…

Text truncated - open the document above for the full version.

Report No.: RF130605C26-1 1 of 48 Report Format Version 5.2.0 FCC TEST REPORT (15.407) REPORT NO.: RF130605C26-1 MODEL NO.: Z5SPM9382 FCC ID: I88Z5SPM9382 RECEIVED: May 23, 2013 TESTED: Jun. 19 ~ Jun. 28, 2013 ISSUED: Jul. 05, 2013 APPLICANT: ZyXEL Communications Corporation ADDRESS: No. 2, Gongye E. 9th Road Hsinchu Science Park, Hsinchu, Taiwan ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the com pliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF130605C26-1 2 of 48 Report Format Version 5.2.0 TABLE OF CONTENTS RELEASE CONTROL RECORD .............................................................................................................. 4 1. CERTIFICATION .......................................................................................................................... 5 2. SUMMARY OF TEST RESULTS ................................................................................................. 6 2.1 MEASUREMENT UNCERTAINTY .............................................................................................. 6 3. GENERAL INFORMATION .......................................................................................................... 7 3.1 GENERAL DESCRIPTION OF EUT ............................................................................................ 7 3.2 DESCRIPTION OF TEST MODES .............................................................................................. 8 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL .............................................. 9 3.3 DUTY CYCLE OF TEST SIGNAL .............................................................................................. 11 3.4 DESCRIPTION OF SUPPORT UNITS ...................................................................................... 15 3.4.1 CONFIGURATION OF SYSTEM UNDER TEST ....................................................................... 15 3.5 GENERAL DESCRIPTION OF APPLIED STANDARDS ........................................................... 16 4. TEST TYPES AND RESULTS ................................................................................................... 17 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT ................................................... 17 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT................................. 17 4.1.2 LIMITS OF UNWANTED EMISSION OUT OF THE RESTRICTED BANDS ............................ 17 4.1.3 TEST INSTRUMENTS ............................................................................................................... 18 4.1.4 TEST PROCEDURES ............................................................................................................... 19 4.1.5 DEVIATION FROM TEST STANDARD ..................................................................................... 19 4.1.6 TEST SETUP ............................................................................................................................. 20 4.1.7 EUT OPERATING CONDITION ................................................................................................ 20 4.1.8 TEST RESULTS ........................................................................................................................ 21 4.2 CONDUCTED EMISSION MEASUREMENT ............................................................................ 30 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ......................................................... 30 4.2.2 TEST INSTRUMENTS ............................................................................................................... 30 4.2.3 TEST PROCEDURES ............................................................................................................... 31 4.2.4 DEVIATION FROM TEST STANDARD ..................................................................................... 31 4.2.5 TEST SETUP ............................................................................................................................. 31 4.2.6 EUT OPERATING CONDITIONS .............................................................................................. 31 4.2.7 TEST RESULTS ........................................................................................................................ 32 4.3 PEAK TRANSMIT POWER MEASUREMENT .......................................................................... 34…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST 2 3 RADIATED EMISSION TEST 4