IKQBLEDIEe-Dice

User Manual e-Dice

FCC INFORMATION This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

Scosche Industries Inc

Scosche Industries Inc

Report No: C130603Z06-RP1 Page 1 / 1 External Photos of EUT

Label and Location FCC ID: IKQBLEDIE

Report No: C130603Z06-RP1 Page 1 / 3 Internal Photos of EUT Report No: C130603Z06-RP1 Page 2 / 3 Report No: C130603Z06-RP1 Page 3 / 3

FCC RF Exposure FCC ID: IKQBLEDIE Frequency: 2402-2480 MHz (40 channels) Modulation: GFSK Mid-Channel Peak Power or Highest Conducted if higher (measured): -2.88 dBm == 0.52 mW Antenna Gain: G = 0 dBi Peak, Radiated = -2.88 dBm + 0 dBi = -2.88 dBm = 0.52 mW SAR Test Exclusion Thresholds specified in KDB447498 Appendix A: Evaluation: The Calculated Radiated Peak output power is taken as worst case, and this emission level appears to be far under the maximum allowed emission level at even the closest distance for 2.4G device specified in this table. Conclusion: The emitted power appears to be (far) below the required limit, so PASS.

Report No.: C130603Z06-RP1 FCC ID: IKQBLEDIE Page 1 / 42 FCC 47 CFR PART 15 SUBPART C for e-Dice Model: e-Dice Brand: SCOSCHE Test Report Number: C130603Z06-RP1 Issued for Scosche Industries Inc 1550 Pacific Ave, Oxnard, CA 93033, USA Issued by: Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. The client should not use it to claim product endorsement by TAF, A2LA, NVLAP, NIST or any government agencies. The test results in the report only apply to the tested sample. Compliance Certification Services (Shenzhen) Inc. No.10-1, Mingkeda Logistics Park, No.18 Huanguan South Rd., Guan Lan Town, Baoan District, Shenzhen, China TEL: 86-755-28055000 FAX: 86-755-28055221 Issued Date: August 20, 2013 Report No.: C130603Z06-RP1 FCC ID: IKQBLEDIE Page 2 / 42 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. Revision History Rev. Issue No. Revisions Effect Page Revised By 00 C130603Z06-RP1 Initial Issue ALL Sinphy Xie Report No.: C130603Z06-RP1 FCC ID: IKQBLEDIE Page 3 / 42 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. TABLE OF CONTENTS 1 TEST CERTIFICATION.............................................................................................. 4 2 TEST RESULT SUMMARY........................................................................................ 5 3 EUT DESCRIPTION ................................................................................................... 6 4 TEST METHODOLOGY ............................................................................................. 7 4.1. DESCRIPTION OF TEST MODES ...................................................................................... 7 5 SETUP OF EQUIPMENT UNDER TEST.................................................................... 8 5.1. DESCRIPTION OF SUPPORT UNITS................................................................................. 8 5.2. CONFIGURATION OF SYSTEM UNDER TEST ................................................................. 8 6 FACILITIES AND ACCREDITATIONS ...................................................................... 9 6.1. FACILITIES .......................................................................................................................... 9 6.2. ACCREDITATIONS ............................................................................................................. 9 6.3. MEASUREMENT UNCERTAINTY....................................................................................... 9 7 FCC PART 15.247 REQUIREMENTS...................................................................... 10 7.1. POWER LINE CONDUCTED EMISSIONS MEASUREMENT........................................... 10 7.2. SPURIOUS EMISSIONS MEASUREMENT....................................................................... 13 7.3. 6dB BANDWIDTH MEASUREMENT ................................................................................. 26 7.4. PEAK OUTPUT POWER ................................................................................................... 29 7.5. BAND EDGES MEASUREMENT....................................................................................... 33 7.6. PEAK POWER SPECTRAL DENSITY MEASUREMENT.................................................. 39 Report No.: C130603Z06-RP1 FCC ID: IKQBLEDIE Page 4 / 42 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. 1 TEST CERTIFICATION Product e-Dice Model e-Dice Brand SCOSCHE Tested June 3~ August 20, 2013 Applicant Scosche Industries Inc 1550 Pacific Ave, Oxnard, CA 93033, USA Manufacturer Sunitec Enterprise Co., Ltd No.2, Qilin Road 2, RunTang Ind, Dan-Keng Village Fu Min Community, Guan-Lan Town, BaoAn District, Shenzhen Guangdong China APPLICABLE STANDARDS Standard Test Type Standard Test Type 15.207(a) Power Line Conducted Emissions 15.247(d) 15.209(a) z Spurious Emissions z Conducted Measurement z Radiated Emissions 15.247(a)(2) 6dB Bandwidth Measurement 15.247(b)(3) 15.247(b)(4) Peak Power Measurement 15.247(d) Band Edges Measurement 15.247(e) Peak Power Spectral Density We hereby certify that: The above equipment was tested by Compliance Certification Services Inc. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4: 2009 and the energy emitted by the sample EUT tested as described in this report is in compliance with the requirements of FCC Rules Part 15.207, 15.209, 15.247. The test results of this report relate only to the tested sample EUT identified in this report. Approved by: Reviewed by: Tom Gan Supervisor of EMC Dept. Compliance Certification Service Inc. Ruby Zhang Supervisor of Report Dept. Compliance Certification Service Inc. Report No.: C130603Z06-RP1 FCC ID: IKQBLEDIE Page 5 / 42 This report shall not be reproduced except in full, without the written approval of Compliance Certification Services. 2 TEST RESULT SUMMARY APPLICABLE STANDARDS Standard Test Type ResultRemark 15.247(a)(2) 6dB Bandwidth Measurement Pass Meet the requirement of limit. 15.247(b)(3) 15.247(b)(4) Peak Power Measurement Pass Meet the requirement of limit. 15.247(d) Band Edges Measurement Pass Meet the requirement of limit. 15.247(e) Peak Power Spectral Density Pass Meet the requirement of limit. 15.247(d) 15.209(a) z Spurious Emissions z Conducted Measurement z Radiated Emissions Pass Meet the requirement of limit. 15.207(a) Power line Conducted Emissions N/A Not applicable, since the EUT powered by the Coin battery. Note: 1. The statements of test result on the above are decided by the request of te…

Text truncated - open the document above for the full version.

Report No.: C130603Z06-RP1 FCC ID: IKQBLEDIE Page 1/1 PHOTOGRAPHS OF THE TEST CONFIGURATION RADIATED EMISSION TEST Below 1GHz Above 1GHz