IKQBTFM3BWireless hands free car kit with Bluetooth and FM

W i r e l e s s h a n d s f r e e c a r k i t B T F M 3 B NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits aredesigned to provide reasonable protection against harmful interference in aresidential installation. This equipment generates uses and can radiate radiofrequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.-Consult the dealer or an experienced radio/TV technician for helpChanges or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.This device contains licence-exempt transmitter(s)/receiver(s) that comply with ? Innovation, Science and Economic Development ? Canada’ s licence-exempt RSS(s). Operation is subject to the following two conditions:(1) This device may not cause interference.(2) This device must accept any interference, including interference that may cause undesired operation of the device.L’ émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’ exploitation est autorisée aux deux conditions suivantes :(1) L' appareil ne doit pas produire de brouillage;(2) L' appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d' en compromettre le fonctionnement. B T F M 3 B B T F M 3 B B T F M 3 B

Scosche Industries Inc 1550 Pacific Ave Oxnard, CA, 93033 Agent Authorization Company: Scosche Industries Inc Address: 1550 Pacific Ave Oxnard, CA, 93033 Product Name: Wireless hands free car kit Model Number(s): BTFM3B, BTFM3-SPB, BTFM3SR-SP Product Description: Wireless hands free car kit with Bluetooth and FM We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: May 12, 2020 Name: Mark Larson Title: SR Product Manager Company: Scosche Industries Inc

Scosche Industries Inc 1550 Pacific Ave Oxnard, CA, 93033 May 12, 2020 Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Subject: Explanation of differences between product types FCC ID: IKQBTFM3B Models: BTFM3B, BTFM3-SPB, BTFM3SR-SP To Whom It May Concern: We, The Scosche Industries Inc hereby declare that the model : BTFM3- SPB, BTFM3SR-SP is identical with the model : BTFM3B, except the model name and the packaging color. Except for the different above, no other modification is performed. Sincerely, Scosche Industries Inc Signature: [Mark Larson, SR Product Manager]

Scosche Industries Inc 1550 Pacific Ave Oxnard, CA, 93033 Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: May 12, 2020 Subject; Request for Confidentiality FCC ID: IKQBTFM3B To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Mark Larson Title: SR Product Manager

External Photos Test model: BTFM3B TOP VIEW OF EUT BOTTOM VIEW OF EUT FRONT VIEW OF EUT BACK VIEW OF EUT LEFT VIEW OF EUT RIGHT VIEW OF EUT Series model: BTFM3-SPB TOP VIEW OF EUT BOTTOM VIEW OF EUT FRONT VIEW OF EUT BACK VIEW OF EUT LEFT VIEW OF EUT RIGHT VIEW OF EUT Series model: BTFM3SR-SP TOP VIEW OF EUT BOTTOM VIEW OF EUT FRONT VIEW OF EUT BACK VIEW OF EUT LEFT VIEW OF EUT RIGHT VIEW OF EUT

FCC ID and IC Label Location 15mm*20mm 15mm*20mm FCC ID: IKQBTFM3B IC: 6955A-BTFM3B HVIN: BTFM3-SPB 15mm*20mm FCC ID: IKQBTFM3B IC: 6955A-BTFM3B HVIN: BTFM3SR-SP

Internal Photos Test model: BTFM3B OPEN VIEW OF EUT INTERNAL VIEW OF EUT-1 INTERNAL VIEW OF EUT-2 INTERNAL VIEW OF EUT-3 BT Antenna FM Antenna port INTERNAL VIEW OF EUT-4

RF EXPOSURE EVALUATION 1. PRODUCT INFORMATION Product Description Wireless hands free car kit Model Name BTFM3B, BTFM3-SPB, BTFM3SR-SP FCC ID IKQBTFM3B 2. EVALUATION METHOD According to 447498 D01 General RF Exposure Guidance v05 The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ·[√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR. Where f(GHz) is the RF channel transmit frequency in GHz Power and distance are rounded to the nearest mW and mm before calculation 3. CALCULATION According to the follow transmitter output power（P t ）formula： P t =（E x d） 2 /（30 x g t ） P t =transmitter output power in watts g t =numeric gain of the transmitting antenna (unitess) E=electric field strength in V/m d=measurement distance in meters (m) BT Pt= -1.449dBm=0.72mW The result for RF exposure evaluation SAR=(0.72mW /5mm) .[√2.48(GHz)]= 0.23<3.0 for 1-g SAR §15.239 FM Pt=-51.74dBm=0.0000067mW The value of the Maximum output power P t is referred to the test report of the CFR47 For frequencies below 100 MHz and test separation distances ≤ 50 mm，the power threshold determined by the following: P max =0.5 * 474 * [1+log(100/f)] mW, where f is MHz For 88.1MHz, P max =250mW. Pt< P max. For 107.9MHz, P = 3 x 5 / 0.1079^0.5 = 45.7 mW P max =45.7mW. Pt< P max. Simultaneous transmission between Bluetooth and FM transmitter: [(max. power of channel, including tune-up tolerance, mW) / (min. test separation distance, mm)]·[√f(GHz)/x] W/kg, for test separation distances ≤ 50 mm; where x = 7.5 for 1-g SAR and x = 18.75 for 10-g SAR. SAR=(0.23+0.00000041)/7.5=0.031W/kg<1.6W/kg 4. CONCLUSION The SAR evaluation is not required.

Page 1 of 23 FCC Test Report Report No.: AGC02180200401FE06 FCC ID : IKQBTFM3B APPLICATION PURPOSE : Original Equipment PRODUCT DESIGNATION : Wireless hands free car kit BRAND NAME : Scosche MODEL NAME : BTFM3B, BTFM3-SPB, BTFM3SR-SP APPLICANT : Scosche Industries Inc DATE OF ISSUE : May 09, 2020 STANDARD(S) : FCC Part 15.239 REPORT VERSION : V1.0 Attestation of Global Compliance(Shenzhen) Co., Ltd CAUTION: This report shall not be reproduced except in full without the written permission of the test laboratory and shall not be quoted out of context. Report No.: AGC02180200401FE06 Page 2 of 23 Report Revise Record Report Version Revise Time Issued Date Valid Version Notes V1.0 / May 09, 2020 Valid Initial Release Report No.: AGC02180200401FE06 Page 3 of 23 TABLE OF CONTENTS 1. VERIFICATION OF CONFORMITY ............................................................................................................ 4 2. GENERAL INFORMATION ......................................................................................................................... 5 2.1.PRODUCT DESCRIPTION .................................................................................................................... 5 3. MEASUREMENT UNCERTAINTY .............................................................................................................. 5 4. DESCRIPTION OF TEST MODES .............................................................................................................. 5 5. SYSTEM TEST CONFIGURATION ............................................................................................................ 6 5.1. EQUIPMENT USED IN EUT SYSTEM .................................................................................................. 6 5.2. SUMMARY OF TEST RESULTS ........................................................................................................... 6 6. TEST FACILITY ........................................................................................................................................... 7 7. RADIATED EMISSION ................................................................................................................................ 8 7.1. MEASUREMENT PROCEDURE ........................................................................................................... 8 7.2.TEST SETUP ........................................................................................................................................ 10 7.3. TEST RESULTFOR FIELD STRENGTH OF FUNDAMENTAL ........................................................... 11 7.4. TEST RESULT FOR FIELD STRENGTH OF BAND EDGE EMISSION ............................................. 11 7.5. TEST RESULT FOR SPURIOUS EMISSION ..................................................................................... 12 8. BANDWIDTH ............................................................................................................................................. 14 8.1. MEASUREMENT PROCEDURE ......................................................................................................... 14 8.2. TEST SETUP ....................................................................................................................................... 14 8.3. TEST RESULT ..................................................................................................................................... 15 APPENDIX A: PHOTOGRAPHS OF TEST SETUP ..................................................................................... 17 APPENDIX B:PHOTOGRAPHS OF EUT ..................................................................................................... 18 Report No.: AGC02180200401FE06 Page 4 of 23 1. VERIFICATION OF CONFORMITY Applicant Scosche Industries Inc Address 1550 Pacific Ave Oxnard,CA,93033 Manufacturer Scosche Industries Inc Address 1550 Pacific Ave Oxnard,CA,93033 Factory Scosche Industries Inc Address 1550 Pacific Ave Oxnard,CA,93033 Product Designation Wireless hands free car kit Brand Name Scosche Test Model BTFM3B Series Model BTFM3-SPB, BTFM3SR-SP Difference Description All the same except for the model name and the packaging color Date of test Apr. 07, 2020 to May 09, 2020 Deviation No any deviation from the test method Condition of Test Sample Normal Test Result Pass Report Template AGCRT-US-BR/RF (2013-03-01) We hereby certify that: The above equipment was tested by Attestation of Global Compliance (Shenzhen) Co., Ltd.The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.10 (2013) and the energy emitted by the sample EUT tested as described in this report is in compliance with radiated emission limits of FCC part 15.239. Prepared By NiNiGuo (ProjectEngineer) May 09, 2020 Reviewed By Max Zhang (Reviewer) May 09, 2020 Approved By Forrest Lei (Authorized Officer) May 09, 2020 Report No.: AGC02180200401FE06 Page 5 of 23 2. GENERAL INFORMATION 2.1.PRODUCT DESCRIPTION A major technical description of EUT is described as following Operation Frequency 88.1MHz-107.9MHz Field Strength(3m) 43.46dBuV/m(Peak)@3m Modulation FM Number of channels 100(Channel spacing 200kHz) Hardware Version HK-BTFM3-AC6926A-V3 Software Version V5.0 Antenna Designation Integral Antenna (Met 15.203 Antenna requirement) Antenna Gain 0.5dBi Power Supply DC 12/24V by car battery NOTE: About the EUT, please refer to User’s Manual. 3. MEASUREMENT UNCERTAINTY - Uncertainty of Radiated Emission below 1GHz, Uc = ±3.9 dB - Uncertainty of Radiated Emission above 1GHz, Uc = ±4.8 dB 4. DESCRIPTION OF TEST MODES NO. TEST MODE DESCRIPTION 1 Transmitting mode(Low channel) 2 Transmitting mode(Middle channel) 3 Transmitting mode(High channel) Note: 1. For Radiated Emission, 3axis were chosen for testing for each applicable mode. 2. All the requirements have beentested by modulating the transmitter with a 2.5 k…

Text truncated - open the document above for the full version.

Test Setup Photos RADIATED EMISSION TEST SETUP BELOW 1GHZ RADIATED EMISSION TEST SETUP ABOVE 1GHZ