IKQR2PLUSRhythm+2.0 Armband Heart Rate Monitor

FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Please note that changes or modifications of this product is not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit dif ferent from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Canadian Compliance Statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence- exempt RSS(s). Operation is subject to the following two conditions: 1) This device may not cause interference. 2) This device must accept any interference, including interference that may cause undesired operation of the device. The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure,users can obtain Canadian information on RF exposure and compliance. Déclaration de Conformité Canadienne L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : 1) L’appareil ne doit pas produire de brouillage; 2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. L'appareil est conforme à l'exemption des limites d'évaluation habituelle de la section 2.5 de RSS 102 et de conformité avec l'exposition aux RF de RSS-102, les utilisateurs peuvent obtenir des informations sur l'exposition aux RF et leur conformité. 史高思贸易(深圳)有限公司 RTHM2.0 CMIIT ID: XXXXXXXXXX IFT: XXXXXXXXXX Complies with IDMA Standards DBXXXXXXX X-00000

Quick Start Guide Scan QR code for more info Fr : Balayez le code QR pour obtenir plus d’information Sp: Escanee el código QR para obtener más información Ger : Für weitere Informationen, scannen Sie den OR-Code Ital: Eseguire la scansione del codice QR per ulteriori informazioni * Multi-Function Button (MFB) *   1. Bluetooth is turned ON within your device. 2. Find the Sensor Settings menu in the Bluetooth Smart Fitness App. 3. Turn on your  and select it in the app to connect.  
 (Sports Watches & Fitness Equipment) 1. From the device settings menu select “Add HR sensor” 2. Turn on your  and select it to connect.  

November 13, 2020 Federal Communications Commission 445 12th Street SW Washington DC 20554 FCC ID: IKQR2PLUS To Whom It May Concern: We, the undersigned, hereby authorize ​Intertek Testing Services Co., ​to act on our behalf in all matters in order to apply to the Federal Communications Commission on our equipment and therefore be responsible to sign the form 731 and other documentation. Any and all acts carried out by ​Intertek Testing Services Co.​, on our behalf shall have the same effect as acts of our own. This authorization is limited to this product; ​IKQR2PLUS ​and is effective beginning ​November 13, 2020​, and expires on ​May 13, 2021. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. We, Scosche Industries, Inc., are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely, Mark Larson Sr. Business Manager on behalf of Scosche Industries 805/486-4450 ext. 127 Mailing: PO Box 2901, Oxnard, CA 93034 Corporate: 1550 Pacific Ave, Oxnard, CA 93033 t: 800.363.4490 f: 805.486.9996 www.scosche.com

November 13, 2020 Attention: Application Examiner FCC ID: IKQR2PLUS PERMANENT CONFIDENTIALITY: Pursuant to 47 CFR Section 0.459 and 0.457(d) of the commission’s rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. ●Schematic(s) ●Block Diagrams ●Operational/Functional Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. Sincerely, Mark Larson Sr. Business Manager on behalf of Scosche Industries 805/486-4450 ext. 127 Mailing: PO Box 2901, Oxnard, CA 93034 Corporate: 1550 Pacific Ave, Oxnard, CA 93033 t: 800.363.4490 f: 805.486.9996 www.scosche.com

1.67mm 13.50mm 1.50mm 4.9mm 4.1mm 26.50mm 7.0mm FCC ID:IKQR2PLUS IC:6955A-R2PLUS FCC ID:IKQR2PLUS IC:6955A-R2PLUS FCC ID:IKQR2PLUS IC:6955A-R2PLUS RTHM2.0 RTHM2.0 1.67 mm RTHM2.0

Intertek Testing Services Shenzhen Ltd. Guangzhou Branch Room 02, & 101/E201/E301/E401/E501/E601/E701/E801 of Room 01 1-8/F., No. 7-2. Caipin Road, Science City, GETDD, Guangzhou, Guangdong, China Job No.: 200715051GZU FCC ID: IKQR2PLUS Version: 08 July 2020 Page 1 of 2 FCC RF Exposure-Portable SAR test exclusion evaluation compliance requirement Model no.: RTHM2.0 1. KDB 447498 D01 v06 requirement Standalone SAR test exclusion considerations: The transmission frequencies of the device are between 100 MHz and 6 GHz. The worst case test separation distance is 5mm. The Max Conducted Output Power and SAR Test Exclusion Threshold (mW) are listed below: BLE: Transmit frequency (GHz) Max Conducted Output Power (mW) SAR Test Exclusion Threshold (mW) 2.480 0.398 9.5 ANT+: Transmit Frequency (GHz) Output power (mW) SAR Test Exclusion Threshold (mW) 2.457 0.398 9.6 The SAR Test Exclusion Threshold is calculated from: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ·[√f(GHz)] ≤ 3.0 for 1-g SAR
f(GHz) is the RF channel transmit frequency in GHz
Power and distance are rounded to the nearest mW and mm before calculation17
The result is rounded to one decimal place for comparison Simultaneous transmission SAR test exclusion considerations: KDB 447498 (D01): When an antenna qualifies for the standalone SAR test exclusion and also transmits simultaneously with other antennas, the standalone SAR value should be estimated according to the following to determine the simultaneous transmission SAR test exclusion: [(max. power of channel, including tune-up tolerance, mW) / (min. test separation distance, mm)]·[√f(GHz)/x] W/kg, for test separation distances ≤ 50 mm; where x = 7.5 for 1-g SAR and x = 18.75 for 10-g SAR. Intertek Testing Services Shenzhen Ltd. Guangzhou Branch Room 02, & 101/E201/E301/E401/E501/E601/E701/E801 of Room 01 1-8/F., No. 7-2. Caipin Road, Science City, GETDD, Guangzhou, Guangdong, China Job No.: 200715051GZU FCC ID: IKQR2PLUS Version: 08 July 2020 Page 2 of 2 FCC RF Exposure-Portable The max. power of ANT+ and Bluetooth are both -4dBm as declared by client, min. test separation is 5 mm, x=7.5 for 1-g SAR: The estimated 1-g SAR1 value of ANT+ is: 0.0167 W/kg The estimated 1-g SAR2 value of Bluetooth is: 0.0167 W/kg The simultaneously transmitting antennas in each operating mode and exposure condition combination must be considered one pair at a time to determine the SAR to peak location separation ratio to qualify for test exclusion. The ratio is determined by (SAR1 + SAR2) 1.5 /Ri, rounded to two decimal digits, and must be ≤ 0.04 for all antenna pairs in the configuration to qualify for 1-g SAR test exclusion. When 10-g SAR applies, the ratio must be ≤ 0.10. SAR1 and SAR2 are the highest reported or estimated SAR values for each antenna in the pair, and Ri is the separation distance in mm between the peak SAR locations for the antenna pair. (SAR1 + SAR2) 1.5 /Ri = (0.0167+0.0167) 1.5 /5 = 0.00122 < 0.04 (Ri = 5mm) According to SAR Exclusion Threshold in KDB 447498 (D01) General RF Exposure Guidance v06, the SAR report is not required. Test Location: Intertek Testing Services Shenzhen Ltd. Guangzhou Branch All tests were performed at: Room102/104, No 203, KeZhu Road, Science City, GETDD Guangzhou, China

Scosche Industries Inc. TEST REPORT SCOPE OF WORK EMC TESTING–RTHM2.0 REPORT NUMBER 200715051GZU-002 ISSUE DATE [REVISED DATE] 16-December-2020 [---------------------] PAGES 26 DOCUMENT CONTROL NUMBER FCC Part 15.249-d © 2017 INTERTEK TEST REPORT Room 02, & 101/E201/E301/ E401/E501/E601/E701/E801 of Room 01 1-8/F., No. 7-2. Caipin Road, Science City, GETDD, Guangzhou, Guangdong, China Telephone: +86 20 8213 9688 Facsimile: +86 20 3205 7538 www.intertek.com.cn This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. Intertek Testing Services Shenzhen Ltd. Guangzhou Branch Room 02, & 101/E201/E301/E401/E501/E601/E701/E801 of Room 01 1-8/F., No. 7-2. Caipin Road, Science City, GETDD, Guangzhou, Guangdong, China Version: 10 June 2019 Page 2 of 26 FCC Part 15.249-d Applicant Name & Address : Scosche Industries Inc. 1550 Pacific Ave, Oxnard, 93033, California, United States of America Manufacturing Site : Same as applicant Intertek Report No: FCC ID: 200715051GZU-002 IKQR2PLUS Test standards 47 CFR PART 15 Subpart C: 2019 section 15.249 Sample Description Product : Rhythm+2.0 Armband Heart Rate Monitor Model No. : RTHM2.0 Electrical Rating : 3.7V Li-ion Battery Charging from USB Port: 5V DC Serial No. : Not Labeled Date Received : 15 July 2020 Date Test Conducted : 19 August 2020-27 August 2020 Prepared and Checked By Oscar Gao Project Engineer Approved By: Helen Ma Team Leader TEST REPORT Intertek Report No.: 200715051GZU-001 Version: 10 June 2019 Page 3 of 26 FCC Part 15.249-d CONTENT TEST REPORT ........................................................................................................................... 1 CONTENT ............................................................................................................................. 3 1.0 TEST RESULT SUMMARY ............................................................................................ 4 2.0 GENERAL DESCRIPTION ............................................................................................. 5 2.1 P RODUCT DESCRIPTION ........................................................................................................ 5 2.2 R ELATED SUBMITTAL(S) GRANTS ........................................................................................... 5 2.3 T EST METHODOLOGY .......................................................................................................... 5 2.4 T EST FACILITY ..................................................................................................................... 6 3.0 SYSTEM TEST CONFIGURATION ................................................................................. 6 3.1 J USTIFICATION .................................................................................................................... 6 3.2 EUT EXERCISING SOFTWARE ................................................................................................. 7 3.3 S PECIAL ACCESSORIES .......................................................................................................... 7 3.4 M EASUREMENT UNCERTAINTY .............................................................................................. 7 3.5 E QUIPMENT MODIFICATION ................................................................................................. 8 3.6 S UPPORT EQUIPMENT LIST AND DESCRIPTION .......................................................................... 8 4.0 MEASUREMENT RESULTS .......................................................................................... 9 4.1 A NTENNA REQUIREMENT ..................................................................................................... 9 4.2 O CCUPIED BANDWIDTH ..................................................................................................... 10 4.3 R ADIATED EMISSION .......................................................................................................... 12 4.4 B AND EDGES REQUIREMENT ............................................................................................... 20 4.5 C ONDUCTED EMISSIONS AT MAINS TERMINALS ..................................................................... 23 5.0 TEST EQUIPMENT LIST ............................................................................................. 26 TEST REPORT Intertek Report No.: 200715051GZU-001 Version: 10 June 2019 Page 4 of 26 FCC Part 15.249-d 1.0 TEST RESULT SUMMARY Test ItemTest RequirementTest Method Result Antenna Requirement FCC PART 15 C Section 15.203 FCC PART 15 C Section 15.203 PASS Occupied Bandwidth FCC PART 15 C section 15.215(c) ANSI C63.10: Clause 6.9 PASS Radiated Emission FCC PART 15 C section 15.249 (a), (d) ANSI C63.10: Clause 6.4, 6.5 & 6.6 PASS Band Edges Measurement FCC PART 15 C section 15.249 (d) ANSI C63.10: Clause 6.10 PASS Conducted Emissions at Mains Terminals FCC PART 15 C section 15.207 ANSI C63.10: Clause 6.2 PASS Remark: N/A: not applicable. Refer to the relative section for the details. EUT: In this whole report EUT means Equipment Under Test. Tx: In this whole report Tx (or tx) means Transmitter. Rx: In this whole report Rx (or rx) …

Text truncated - open the document above for the full version.

Conducted Emission Radiated Emission (Below 1GHz) Radiated Emission (Above 1GHz)