IPH-04578Extremity Worn Digital Transceiver

IMPORTANT SAFETY AND PRODUCT INFORMATION Important Safety and Product Information..................3 Informations importantes sur le produit et la sécurité...........11 guida Informazioni importanti sulla sicurezza e sul prodotto.......19 Wichtige Sicherheits- und Produktinformationen..............26 Información importante sobre el producto y tu seguridad.........34 Informações importantes sobre segurança e sobre o produto.......42 Important Safety and Product Information WARNING Failure to heed the following warnings could result in an accident or medical event resulting in death or serious injury. Battery Warnings A lithium-ion battery is used in this device. If these guidelines are not followed, batteries may experience a shortened life span or may present a risk of damage to the device, fire, chemical burn, electrolyte leak, and/or injury. • Do not expose the device or batteries to fire, explosion, or other hazard. • Do not disassemble, modify, remanufacture, puncture, or damage the device or batteries. • Do not remove or attempt to remove the non-user-replaceable battery. Device Warnings • To avoid possible device damage, do not leave the device exposed to a heat source or in a high-temperature location, such as in the sun in an unattended vehicle. • Do not operate or store the device for an extended time period outside of the applicable temperature range listed in the printed manual in the product packaging. • Do not use a power cable, data cable, and/or power adapter that is not supplied by Garmin ® or is not properly certified. Health Warnings • If you have a pacemaker or other internal electronic device, consult your physician before using a heart rate monitor. • The optical wrist heart rate monitor and pulse oximeter emit lights and flash occasionally. Consult your physician if you have epilepsy or are sensitive to bright or flashing lights. • This device may have a flashlight that can be programmed to flash at various intervals. Consult your physician if you have epilepsy or are sensitive to bright or flashing lights. • Always consult your physician before beginning or modifying any exercise program. • The device, accessories, heart rate monitor, pulse oximeter, and related data are intended to be used only for recreational purposes, not medical purposes, and are not intended to diagnose, monitor, treat, cure, or prevent any disease or condition. 3 EN • The heart rate and blood oxygen saturation readings are for reference only, and no responsibility is accepted for the consequences of any erroneous readings. • While the optical wrist heart rate monitor and pulse oximeter technologies typically provide accurate estimates of a user's heart rate and blood oxygen saturation respectively, there are inherent limitations with the technologies that may cause some of the readings to be inaccurate under certain circumstances, including the user's physical characteristics, device fit and position, and type and intensity of activity. • Activity trackers rely on sensors that track your movement and other metrics. The data provided by these devices is intended to be a close estimation of your activity and metrics tracked, but may not be completely accurate. Safety and Tracking Warning The assistance feature allows you to send your location to an emergency contact. This is a supplemental feature and should not be relied upon as a primary method to obtain emergency assistance. The Garmin Connect ™ app does not contact emergency services on your behalf. The incident detection feature is only available during certain outdoor activities. For more information, see the device owner's manual. Bicycle Warnings • Always use your best judgement, and operate the bicycle in a safe manner. • Make sure your bicycle and hardware are properly maintained and that all parts are correctly installed. Navigation Warnings If your Garmin device uses or accepts map data, follow these guidelines to ensure safe navigating. • Always carefully compare information displayed on the device to all available navigation sources, including weather conditions, maps, street/trail signs and conditions, waterway restrictions, and other factors that may affect safety. Always resolve any discrepancies or questions before continuing navigation, and defer to posted signs and conditions. • Use this device only as a navigational aid. Do not attempt to use the device for any purpose requiring precise measurement of direction, distance, location, or topography. 4 EN • Always use your best judgment and exercise common sense when making off-road navigational decisions. The device is designed to provide route suggestions only. It is not a replacement for attentiveness and proper preparation for outdoor activities. Do not follow the route suggestions if they suggest an illegal course or would put you in an unsafe situation. • Always be mindful of the effects of the environment and the inherent risks of the activity before embarking on off-road activities, especially the impact that weather and weather-related trail conditions can have on the safety of your activity. Ensure that you have the proper gear and supplies for your activity before navigating unfamiliar paths and trails. CAUTION Failure to heed the following cautions could result in minor or moderate injury, or property damage. Skin Irritation Some users may experience skin irritation after prolonged use of the watch, especially if the user has sensitive skin or allergies. If you notice any skin irritation, remove the watch and give your skin time to heal. To help prevent skin irritation, ensure the watch is clean and dry, and do not overtighten the watch on your wrist. For more information, go to garmin.com/fitandcare. NOTICE Failure to heed the following notices could result in personal or property damage, or negatively impact the device functionality. Battery Notice Contact your local waste disposal department to dispose of the device/ batteries in accordance with applicable local…

Text truncated - open the document above for the full version.

© Celltech Labs Inc – 2021 ____________________________________________________________________________________________________ Celltech Labs Inc., 21-364 Lougheed Road, Kelowna, British Columbia, Canada V1X 7R8 Tel: 1-250-765-7650 FCC Test Lab: CA3874 Date: 15 December 2022 To: Federal Communications Commission 7435 Oakland Mills Road Columbia, Maryland 21046 USA RE: New Certification Request, FCC ID: IPH-04578 Dear FCC Representative This is a new Certification request for FCC ID: IPH-04578, HVIN: A04578. The A04578 is an extremity-worn WiFi, BlueTooth, BlueTooth Low Energy, ANT and NFC transceiver. The device has been evaluated and passes the requirements of 47 CFR §15.247, §15.249, §15.225and §2.1093. The WiFi/BT/ANT transmitters share the same antenna and cannot simultaneously transmit. The NFC transmitter has an output power of -36dBm and qualifies for SAR Test Exclusion. Should there be any questions or concerns with this filing, please feel free to contact me. Sincerely, Art Voss, P.Eng., BS EE Technical Manager 21-364 Lougheed Rd Kelowna, BC, V1X 7R8, Canada 250-765-7650 Ext 202 [email protected] www.celltechlabs.com

December 16, 2022 Timco Engineering Inc. 849 NW State Road 45 Newberry, FL 32669 Re: Grant Deferral: Garmin International, Inc. FCC ID: IPH-04578 Please be advised that Garmin International, Inc. is requesting a deferral of the issuance of the Grant of Authorization for FCC ID: IPH-04578 until the following date: December 30, 2022 Please process this application as normally required and advise of any issues. Should you require additional information please let us know. Thank you. Sincerely, Garmin International, Inc. David Utt, Staff Compliance Engineer

Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columb ia, MD 21046 Date: December 6, 2022 SUBJECT: FCC Application for FCC ID: IPH-04578 To Whom It May Co ncern: Garmin will continue to apply processes and procedures to ensure compliance with 47 CFR 2 requirements regarding products produced under supplier's Declaration of Conformity procedure for class B computer peripheral portion as applicable to this composite filing. Sincerely, David Utt Staff Compliance Engineer Wellness & Fitness Products

December 6, 2022 Federal Communications Commission Equip Approval Services Post Office Box 358315 Pittsburgh, Pennsylvania 15215-5315 To Whom It May Concern: Pursuant to 47 CFR 2.911, Garmin International, Inc. (Garmin) has authorized Ben Hewson and Art Voss of Celltech Labs Inc. (Celltech) to act on Garmin’s behalf for the sole and express purpose of processing applications to the Federal Communication Commission (FCC) for equipment FCC authorization. This authorization is limited to FCC ID: IPH-04 578. Consistent with the foregoing, Ben Hewson and Art Voss are authorized to: 1)Sign Form 731, 2)Sign letters of application, 3)Request confidentiality, and 4)Exchange data and information with the FCC, and authorized TCBs on behalf of Garmin. This authorization is not assignable to other beyond Ben Hewson and Art Voss. No party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C 862. We also declare that the information provided to the FCC is true and correct to the best of our knowledge (47 CFR 2.911(d)) and we have been informed of the grantee responsibilities (47 CFR 2.909) with regard to certified equipment. This authorization expires December 6, 2023. Sincerely, David Utt Staff Compliance Engineer, Wel lness & Fitness Products -----------------------------------------------------nothing f ollows----------------------------------------------------

May 6, 2022 Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Innovation, Science and Economic Development Canada Certification and Engineering Bureau 3701 Carling Avenue PO Box 11490, Station H Ottawa, Ontario, Canada K2H 8S2 To Whom It May Concern: Pursuant to 47 CFR 2.911, Garmin International, Inc. (Garmin) has authorized the following Garmin International Associates to act on Garmin's behalf for the sole and express purpose of processing applications to the Federal Communication Commission (FCC) and Innovation, Science and Economic Development Canada (ISED) for equipment authorization or certification. Mr. Chris Strauss, Compliance Engineering Team Lead Mr. William Pertner, Compliance Engineering Team Lead Mr. Jay Everett, Compliance Engineering Team Lead Mr. Mike Moranha, Compliance Engineer Ms. Poojita Bhattu, Compliance Engineer Mr. Doug Burroughs, Compliance Engineer Mr. Jeffrey Hailey, Compliance Engineer Mr. Dan Irish, Compliance Engineer Mr. Kiran Kumar, Compliance Engineer Mr. Tim Olson, Compliance Engineer Mr. Carlos Ortega, Compliance Engineer Mr. Cody Riggle, Compliance Engineer Mr. David Utt, Staff Compliance Engineer Mr. Jonathan Shafer, Design Certification Engineer Ms. Sara Jones, Design Certification Engineer As such, the Garmin Associates listed above are authorized to: 1) sign Form 731, 2) sign letters of application, 3) request confidentiality, and 4) exchange data and information with the FCC, IC and/or authorized TCBs on behalf of Garmin. In addition, these individuals shall be considered "authorized individuals" to act on Garmin's behalf where an "authorized individual's" attestation is necessary or preferred. This authorization remains in effect until notified to the contrary by Garmin. Sincerely, Ben Karsak Manager Compliance Engineering Garmin International, Inc.

E-Label Description The following is provided on the exterior of the packaging that is provided with the device:

Test Report S/N: 45461765 R1.0 Test Report Issue Date: 6 December 2022 ©2022 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the expressed written permission of Celltech Labs Inc. Page 40 of 42 APPENDIX D – PROBE CALIBRATION Test Report S/N: 45461765 R1.0 Test Report Issue Date: 6 December 2022 ©2022 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the expressed written permission of Celltech Labs Inc. Page 41 of 42 APPENDIX E – DIPOLE CALIBRATION NCL CALIBRATION LABORATORIES Calibration File No: DC-1904 Project Number: 5921 Client.: Celltech Address: 21 – 364 Lougheed Road, Kelowna, BC V1X 7R8, Canada C E R T I F I C A T E OF C A L I B R A T I O N It is certified that the equipment identified below has been calibrated in the NCL CALIBRATION LABORATORIES by qualified personnel following recognized procedures and using transfer standards traceable to NRC/NIST. Validation Dipole (Head) Manufacturer: SPEAG Part number: D2450V2 Frequency: 2450 MHz Serial No: 825 Calibrated: 27/04/2021 Released on: 05/05/2021 This Calibration Certificate is incomplete unless accompanied by the Calibration Results Summary NCL Calibration Laboratories Division of APREL Laboratories DC-1904 Dipole SN: 825 Page 2 of 7 This page has been reviewed for content and attested to on Page 2 of this document. Conditions Dipole SN 825 was a re-calibration. Ambient Temperature of the Laboratory: 21 C +/- 0.5C Temperature of the Tissue: 21 C +/- 0.5C Primary Measurement Standards Instrument Serial Number Cal due date Signal Generator HP 83640B 3844A00689 Sept. 17, 2022 Network Analyzer Keysight E5063A MY54502902 Mar. 9, 2023 Spectrum Analyzer Keysight N9030B MY57140772 Apr. 20, 2023 Attestation The below named signatories have conducted the calibration and review of the data which is presented in this calibration report. NCL Calibration Laboratories Division of APREL Laboratories DC-1904 Dipole SN: 825 Page 3 of 7 This page has been reviewed for content and attested to on Page 2 of this document. Calibration Results Summary The following results relate the Calibrated Dipole and should be used as a quick reference for the user. Tissue Validation Tissue Frequency Dielectric constant,  r Conductivity,  [S/m] Head 2450 MHz 40.73 1.86 Electrical Specification Tissue Frequency Return LossImpedanceSWR: Head 2450 MHz -19.83 dB 43.26  1.23U System Validation Results Tissue Frequency 1-Gram SAR 10-Gram SAR Uncertainty Head 2450 MHz 52.719 W/kg 24.015 W/kg 19.8% Head NCL Calibration Laboratories Division of APREL Laboratories DC-1904 Dipole SN: 825 Page 4 of 7 This page has been reviewed for content and attested to on Page 2 of this document. Introduction This Calibration Report has been produced in line with the SSI Dipole Calibration Procedure SSI-TP-018-ALSAS. The results contained within this report are for Validation Dipole SN 825. The calibration routine consisted of a three-step process. Step 1 was a mechanical verification of the dipole to ensure that it meets the mechanical specifications. Step 2 was an Electrical Calibration for the Validation Dipole, where the SWR, Impedance, and the Return loss were assessed. Step 3 involved a System Validation using the ALSAS-10U, along with APREL E-020 30 MHz to 6 GHz E-Field Probe Serial Number 225. References o IEEE Standard 1528:2013 IEEE Recommended Practice for Determining the Peak Spatial-Average Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques o EN 62209-1:2016 Human Exposure to RF Fields from hand-held and body-mounted wireless communication devices - Human models. instrumentation, and procedures - Part 1: Procedure to measure the Specific Absorption Rate (SAR) for hand-held mobile wireless devices o IEC 62209-2:2019 Human exposure to RF fields from hand-held and body-mounted wireless devices - Human models, instrumentation, and procedures - Part 2: specific absorption rate (SAR) for wireless communication devices (30 MHz - 6 GHz) o D22-012-Tissue dielectric tissue calibration procedure o D28-002-Dipole procedure for validation of SAR system using a dipole o IEEE 1309 Standard for Calibration of Electromagnetic Field Sensors and Probes, Excluding Antennas, from 9 kHz to 40 GHz Conditions Ambient Temperature of the Laboratory: 21 C +/- 0.5C Temperature of the Tissue: 21 C +/- 0.5C Dipole Calibration uncertainty The calibration uncertainty for the dipole is made up of various parameters presented below. Tolerance, % Mechanical 2.00 Positioning Error 0.10 Electrical 0.37 Tissue Permittivity 3.88 Tissue Conductivity 3.56 Dipole Validation 1.70 Combined Uncertainty, k=2 4.81 NCL Calibration Laboratories Division of APREL Laboratories DC-1904 Dipole SN: 825 Page 5 of 7 This page has been reviewed for content and attested to on Page 2 of this document. The Following Graphs are the results as displayed on the Vector Network Analyzer. Electrical Calibration Test Head S11 R/L -19.83 dB Impedance 43.26  SWR 1.23 U S11 Parameter Return Loss Head Frequency Range 2326.59 MHz to 2450 MHz NCL Calibration Laboratories Division of APREL Laboratories DC-1904 Dipole SN: 825 Page 6 of 7 This page has been reviewed for content and attested to on Page 2 of this document. Smith Chart Dipole Impedance Head NCL Calibration Laboratories Division of APREL Laboratories DC-1904 Dipole SN: 825 Page 7 of 7 This page has been reviewed for content and attested to on Page 2 of this document. SWR Head Test Report S/N: 45461765 R1.0 Test Report Issue Date: 6 December 2022 ©2022 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the expressed written permission of Celltech Labs Inc. Page 42 of 42 APPENDIX F - PHANTOM

Antenna Gain Information: A04578 Equipment Description: This report contains the antenna gain information for the Wi-Fi /ANT/BLE antenna for Garmin Model A04578. The operational frequency of these technologies is approximately 2402-2480 MHz, and the maximum gain within the frequency band is reported. Reported Data: Maximum Gain for Wi-Fi/BT/BLE/ANT -3.6 dBi Procedure: Garmin uses an ETS-Lindgren AMS-8500 3D Fully Anechoic Automated Antenna Measurement System. The measurement chamber is fully anechoic and contains both the Equipment Under Test (EUT) and the measurement antenna. The EUT is mounted on a Multi-Axis Positioner, which can orient the antenna in all orientations relative to the measurement antenna. The measurement antenna is dual-polarized and measures both horizontal and vertical polarization simultaneously. The other equipment includes a Vector Signal Generator, a multi-channel Vector Network Analyzer, and a control PC. Data is taken and analyzed using EMQuest Data Acquisition and Analysis Software. The output includes the maximum 3D antenna gain within the frequency band. Setup: Equipment List: 3D Chamber PC interfaced to Test Equipment EMQuest Software w/ Required Drivers for Equipment Installed AMS-8500 Anechoic Wireless Test Chamber Dual Polarization Measurement Antenna (ETS 3164) Multi-Axis Positioning System (MAPS) Multi-Axis Positioning Controller (ETS EMCO Model 2090) Network Analyzer (Agilent E5017C) Automated RF Switch Controller (Agilent) Additional Information: • Photos of the antenna are provided in Exhibit 19 – Photos – DUT Internal.pdf • The Photos include a scale for dimensions Signature: David Utt, Staff Compliance Engineer Garmin International, Inc.

USA A04578A04578 Olathe, KS, 66062 1200 East 151 St Product Model Number / HVINProduct Marketing Name / PMN Test Lab Certificate: 2470.01 Test Report Serial Number: Test Report Date: EMC Test Report - New Certification 45461773 R1.0 Project Number: 16 December 2022 1603 In Accordance With: FCC ID:IC Registration Number Applicant: IPH-045781792A-04578 Garmin International Inc. Approved By: RSS-Gen, RSS-247 Issue 2 Digital Transmission Systems (DTSs), Frequency Hopping Systems (FHSs) and Licence-Exempt Local Area Network (LE-LAN) Devices © 2022 Celltech Labs Inc, This report shall not be reproduced in any form without the expressed written consent of Celltech Labs Inc. CFR Title 47, Part 15 Subpart C (§15.247), Part 15 Subpart B Digital Transmission System (DTS) FCC Registration: CA3874 Ben Hewson, President Celltech Labs Inc. IC Registration 3874A-1 21-364 Lougheed Rd. Kelowna, BC, V1X 7R8 Canada Test Report S/N: 45461773R1.0 Test Report Issue Date: 16 December 2022 ©2022 Celltech Labs Inc. This document is not to be reproduced in whole or in part without the expressed written permission of Celltech Labs Inc. Page 2 of 74 Table of Contents 1.0 DOCUMENT CONTROL ................................................................................................................................................... 5 2.0 CLIENT AND DUT INFORMATION .................................................................................................................................. 6 3.0 SCOPE .............................................................................................................................................................................. 7 4.0 TEST SUMMARY .............................................................................................................................................................. 8 5.0 NORMATIVE REFERENCES ......................................................................................................................................... 10 6.0 FACILITIES AND ACCREDITATIONS ........................................................................................................................... 11 7.0 OCCUPIED BANDWIDTH .............................................................................................................................................. 12 8.0 DTS BANDWIDTH .......................................................................................................................................................... 15 9.0 DUTY CYCLE AND TRANSMISSION DURATION ........................................................................................................ 24 10.0 ANTENNA PORT CONDUCTED POWER, (DTS) ....................................................................................................... 25 11.0 ANTENNA PORT CONDUCTED POWER, (DSS) ....................................................................................................... 27 12.0 POWER SPECTRAL DENSITY .................................................................................................................................... 29 13.0 FHSS NUMBER OF HOPPING CHANNELS ................................................................................................................ 32 14.0 FHSS CHANNEL SEPARATION .................................................................................................................................. 38 15.0 FHSS TIME OF OCCUPANCY ..................................................................................................................................... 44 16.0 CONDUCTED SPURIOUS EMISSIONS -BAND EDGE ............................................................................................... 51 17.0 CONDUCTED SPURIOUS EMISSIONS ...................................................................................................................... 54 18.0 RADIATED TX SPURIOUS EMISSIONS, RESTRICTED BAND ................................................................................. 57 19.0 RADIATED RX SPURIOUS EMISSIONS ..................................................................................................................... 60 20.0 POWER LINE CONDUCTED EMISSIONS .................................................................................................................. 62 APPENDIX A – TEST SETUP DRAWINGS ......................................................................................................................... 67 APPENDIX B – EQUIPMENT LIST AND CALIBRATION ..................................................................................................... 72 APPENDIX C – MEASUREMENT INSTRUMENT UNCERTAINTY ..................................................................................... 73 END OF REPORT ................................................................................................................................................................. 73 APPENDIX D – OCCUPIED BANDWIDTH MEASUREMENT PLOTS ................................................................................ 74 APPENDIX E – ANTENNA PORT CONDUCTED POWER MEASUREMENT PLOTS ....................................................... 74 APPENDIX F – POWER SPECTRAL DENSITY MEASUREMENT PLOTS ........................................................................ 74 APPENDIX G – CONDUCTED SPURIOUS EMISSIONS, BAND EDGE MEASUREMENT PLOTS ................................... 74 APPENDIX H – CONDUCTED SPURIOUS EMISSIONS .................................................................................................... 74 APPENDIX I – RADIATED TX SPURIOUS EMISSIONS, RESTRICTED BAND MEASUREMENT PLOTS ....................... 74 APPENDIX J – RADIATED RX SPURIOUS EMISSIONS MEASUREMENT PLOTS .......................................................... 74 Table of Figures Figure A.1 – Test Setup – Conducted Measurements ..........................................................................…

Text truncated - open the document above for the full version.

MeasuredLimit Emission e.r.p./e.r.i.p. Margin RangePolarization [E Meas ][A L ] (dBm)(dBm) (dB) 9kHz - 30MHzFrontND-57.0n/a 30-1000MHzND-57.0n/a 1 - 3GHzND-47.0n/a 3 - 13.6GHzND-47.0n/a 13.6 - 18GHzND-47.0n/a 18 - 25GHzND-47.0n/a 9kHz - 30MHzSideND-57.0n/a 30-1000MHzND-57.0n/a 1 - 3GHzND-47.0n/a 3 - 13.6GHzND-47.0n/a 13.6 - 18GHzND-47.0n/a 18 - 25GHzND-47.0n/a Frequency Horizontal Measurement Results Results: Antenna Complies Vertical AntennaEmissionMeasured FrequencyEmission (MHz)(dBm) Front NDND Radiated Rx Emissions: Polarization 0 20 40 60 80 100 120 0.0010.0100.1001.00010.000100.000 Amplitude (dBuV) Frequency (MHz) Radiated Rx Emissions (9kHz - 30MHz) OATS Front FCC §15.209, ISED RSS-Gen 8.9 DUT AntennaEmissionMeasured FrequencyEmission (MHz)(dBm) Side NDND Radiated Rx Emissions: Polarization 0 20 40 60 80 100 120 0.0010.0100.1001.00010.000100.000 Amplitude (dBuV) Frequency (MHz) Radiated Rx Emissions (9kHz - 30MHz) OATS Side FCC §15.209, ISED RSS-Gen 8.9DUT Width 5.75" dBm Radiated Rx Emissions Frequency Range:Antenna PolarizationMeasured Emission: 30 - 1000MHz Horizontal None Detected (ND) 0 10 20 30 40 50 60 101001000 Amplitude (dBuV) Frequency (MHz) Radiated Rx Emissions (30MHz - 1GHz) OATS Horizontal CISPR B Limit RE Rx Width 5.75" dBm Radiated Rx Emissions Frequency Range:Antenna PolarizationMeasured Emission: 30 - 1000MHz Vertical None Detected (ND) 0 10 20 30 40 50 60 101001000 Amplitude (dBuV) Frequency (MHz) Radiated Rx Emissions (30MHz - 1GHz) OATS Horizontal CISPR B Limit RE Rx Width 5.75" dBm Radiated Rx Emissions Frequency Range:Antenna PolarizationMeasured Emission: 1 - 3GHz Horizontal None Detected (ND) Ref 87 dBμV * A TDF Att 0 dB 200 MHz/Start 1 GHzStop 3 GHz * RBW 1 MHz VBW 10 MHz SWT 10 ms *1 RM VIEW 3DB *2 RM VIEW -10 0 10 20 30 40 50 60 70 80 1 Marker 1 [T1 ] 18.35 dBμV 3.000000000 GHz Date: 3.NOV.2022 14:53:56 Width 5.75" dBm Radiated Rx Emissions Frequency Range:Antenna PolarizationMeasured Emission: 1 - 3GHz Vertical None Detected (ND) Ref 87 dBμV * A TDF Att 0 dB 200 MHz/Start 1 GHzStop 3 GHz * RBW 1 MHz VBW 10 MHz SWT 10 ms *1 RM VIEW 3DB *2 RM VIEW -10 0 10 20 30 40 50 60 70 80 1 Marker 1 [T1 ] 16.81 dBμV 2.742160000 GHz Date: 3.NOV.2022 14:50:46 Width 5.75" dBm Radiated Rx Emissions Frequency Range:Antenna PolarizationMeasured Emission: 3 - 10GHz Horizontal None Detected (ND) Ref 87 dBμV * A TDF 3DB Att 0 dB RBW 1 MHz VBW 10 MHz SWT 140 ms * Start 3 GHzStop 10 GHz700 MHz/ *1 RM VIEW -10 0 10 20 30 40 50 60 70 80 1 Marker 1 [T1 ] 23.68 dBμV 9.006000000 GHz Date: 3.NOV.2022 14:54:23 Width 5.75" dBm Radiated Rx Emissions Frequency Range:Antenna PolarizationMeasured Emission: 3 - 10GHz Vertical None Detected (ND) Ref 87 dBμV * A TDF 3DB Att 0 dB RBW 1 MHz VBW 10 MHz SWT 140 ms * Start 3 GHzStop 10 GHz700 MHz/ *1 RM VIEW -10 0 10 20 30 40 50 60 70 80 1 Marker 1 [T1 ] 23.97 dBμV 3.154000000 GHz Date: 3.NOV.2022 14:51:10 Width 5.75" dBm Radiated Rx Emissions Frequency Range:Antenna PolarizationMeasured Emission: 10 - 13.6GHz Horizontal None Detected (ND) Ref 87 dBμV * A TDF 3DB Att 0 dB RBW 1 MHz VBW 10 MHz SWT 75 ms * Start 10 GHzStop 13.6 GHz360 MHz/ *1 RM VIEW -10 0 10 20 30 40 50 60 70 80 1 Marker 1 [T1 ] 23.70 dBμV 13.222000000 GHz Date: 3.NOV.2022 14:54:43 Width 5.75" dBm Radiated Rx Emissions Frequency Range:Antenna PolarizationMeasured Emission: 10 - 13.6GHz Vertical None Detected (ND) Ref 87 dBμV * A TDF 3DB Att 0 dB RBW 1 MHz VBW 10 MHz SWT 75 ms * Start 10 GHzStop 13.6 GHz360 MHz/ *1 RM VIEW -10 0 10 20 30 40 50 60 70 80 1 Marker 1 [T1 ] 23.45 dBμV 13.211200000 GHz Date: 3.NOV.2022 14:51:34 Width 5.75" dBm Radiated Rx Emissions Frequency Range:Antenna PolarizationMeasured Emission: 13 - 18GHz Horizontal None Detected (ND) Ref 87 dBμV * A TDF 3DB Att 0 dB RBW 1 MHz VBW 10 MHz SWT 90 ms * Start 13.6 GHzStop 18 GHz440 MHz/ *1 RM VIEW -10 0 10 20 30 40 50 60 70 80 1 Marker 1 [T1 ] 34.76 dBμV 16.438000000 GHz Date: 3.NOV.2022 14:54:57 Width 5.75" dBm Radiated Rx Emissions Frequency Range:Antenna PolarizationMeasured Emission: 13 - 18GHz Vertical None Detected (ND) Ref 87 dBμV * A TDF 3DB Att 0 dB RBW 1 MHz VBW 10 MHz SWT 90 ms * Start 13.6 GHzStop 18 GHz440 MHz/ *1 RM VIEW -10 0 10 20 30 40 50 60 70 80 1 Marker 1 [T1 ] 34.78 dBμV 16.424800000 GHz Date: 3.NOV.2022 14:51:53 Width 5.75" dBm Radiated Rx Emissions Frequency Range:Antenna PolarizationMeasured Emission: 18 - 25GHz Horizontal None Detected (ND) * A TDF Att 0 dBRef 87 dBμV 700 MHz/Start 18 GHzStop 25 GHz * RBW 1 MHz VBW 10 MHz SWT 140 ms 3DB *1 RM VIEW -10 0 10 20 30 40 50 60 70 80 1 Marker 1 [T1 ] 36.39 dBμV 24.685000000 GHz Date: 3.NOV.2022 16:36:22 Width 5.75" dBm Radiated Rx Emissions Frequency Range:Antenna PolarizationMeasured Emission: 18 - 25GHz Vertical None Detected (ND) * A TDF Att 0 dBRef 87 dBμV 700 MHz/…

Text truncated - open the document above for the full version.