IPH-M2AINX01LOW POWER TRANSMITTER (2400-2483.5 MHz)

- Instrument - Installation and Operation Manual English WIND Pack English 1 English 5 1 Installation • The installation includes 6 major steps: 1. Read the installation and operation manual. 2. Plan where to install the transducers and instruments. 3. Run the cables. 4. Install the transducers and instruments. 5. Take a break and admire your installation. 6. Learn the functions and calibrate your system. Before you begin drilling ... think about how you can make the installation as neat and simple as your boat will allow. Plan where to position the transducers, WSI-box and instruments. Think about leaving space for additional instruments in the future. • A few ”do nots” you should consider: − Do not cut the cables too short. Allow extra cable length at the Inertface box so it can be disconnected for inspection w ithout having to disconnect all attached cables. − Do not place sealant behind the display. The instrument gasket eliminates the need for sealant. − Do not run cables in the bilge, where water can appear. − Do not run cables close to fluorescent light sources, engine or radio transmitting equipment to avoid electrical disturbances. − Do not rush, take your time. A neat installation is easy to do. • The following material is needed: Wire cutters and strippers. Small Philips and small flat head screw driver. Hole saw for the instrument clearance hole 63 mm (2½"). 5 mm ( 1 / 4 ") drill for the mounting holes. If y ou are doubtful about the installation, obtain the services of an experienced technician. English 6 1.1 Installing the instrument • Place the adhesive drill template on the desired location for the instrument. Drill the 2 holes using a 5 mm (1/4") drill for the tw o pin bolts. Use a 63 mm (2½") hole saw to machine the clearance hole for the instrument connection socket. Remove the template. • Screw the two pin bolts to the instrument • Put the instrument in place • Screw the two nuts from the back Note! The two nuts must just be tighten by hand only • Run the Netw ork cable from the Interface box to the instrument. • If you want to cut the Netw ork cable to length, disconnect 4-pole jack plug and cut the cable. Peel off about 35 mm (1.4") of the cable insulation. Remove about 6 mm (1/4") from the 3 isolated w ires (the 4th w ire is an earth / screen). Attach the 4 cable protectors to the wires using a pair of flat pliers. • Connect the 4 cable protectors to the 4-pole jack plug as shown. Apply silicon paste on all locations as shown. Note: Must be done to avoid corrosion. Silicon paste English 7 • Apply silicon paste to the instrument connection pins at the back of the instrument. Press the jack plug onto the instrument pins. Press the cable in to the cable leads. • Mount the connection back cover with the screw. 1.1.1 Installing instrument to the Interface box All instruments are connected directly to the Network. They all use the same colour coded 4-pole jack plugs. (F or instrument installation, see 2.2). English 3 Part specification ___________________________________________________________ Items delivered with the instrument Qty Description Reference 1 Instrument package 2 1 Interface box 3 1 Instrument cover 4 1 Drill template for instrument 5 1 Installation and operating manual 6 1 Warranty card 7 2 Instrument mounting screws 8 2 Plastic nuts 8 1 Connection back cover 8 2 Silicon paste tube 8 2 Plastic cable strap 8 1 Network cable, 8 m (26 ft)10 5 Cable protectors, 0,25 mm (0.1 inch) 11 5 Cable protectors, 0,75 mm (0.3 inch) 11 1 3m red power cable 12 1 3m black power cable 13 3 Mounting screws for instrument19 1 Instrument 20 1 Instrument bracket20 3 Mounting screws for Interface bo21 Registering this product Once you have checked that y ou have all the listed parts, please take time to fill in the warranty document and return it to your national distributor. By returning the w arranty card, it w ill assist y our distributor to give y ou prompt and expert attention. Keep y our proof of purchase. Also, your details are added to our customer database so that you automatically receive new product catalogues w hen they are released. Warranty conditions see 12. English 9 1.3.4 Mounting the Instrument step by step 1. Mark the mounting holes using the bracket as an template 3. Mount the bracket with the three supplied screws 5. Tighten the lock nut by hand only (do not use any tool) 2. Drill the three mounting holes using a 3,2mm drill 4. Insert the transducer into the bracket from front to back 6. Attach the security clamp English 10 2 Connection to other systems A system is fully compatible with other Network systems. If you want to connect the system to a system, you have to move the connection of the log and depth transducers to the Interface box. Note that a 200kHz depth transducer must be used. The 200kHz transducer is recognized by the colour of the leads that should be blue, black and screen. If your existing depth transducer has other colours of the transducer leads, it has to be changed. 200kHz transducers are available for all types of products through hull fittings. The network cable of the system may be connected at any location in the existing system. That is normally at the Server but if it is more convenient, you may connect the Network cable to any existing instrument. 3 Pairing procedure of Instrument When all instruments have been installed, a pairing procedure between the Instrument and the Interface unit must be made to introduce it to your specific network system. This is how you do it: a. Make sure the Instrument is fully charged! If the Instrument has been stored in a dark place for a long time, you must first charge it by exposing the solar cell for sun light some hours before use. b. Pairing! Hold the Instrument within 2m from the Interface unit, and then press the INIT button (through the hole in the bottom of the battery lid) by use of the “pin”. If the batter lid is open, you may see the LED. The built in LED will flash 2 times then lit for…

Text truncated - open the document above for the full version.

Important Safety and Product Information Declaration of Conformity Hereby, Garmin, declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. To view the full Declaration of Conformity, go to www.garmin.com/compliance. Industry Canada Compliance Category I radiocommunication devices comply with Industry Canada Standard RSS-210. Category II radiocommunication devices comply with Industry Canada Standard RSS-310. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. FCC Compliance This product has been tested and found to comply with Part 15 of the FCC interference limits for Class B digital devices FOR HOME OR OFFICE USE. These limits are designed to provide more reasonable protection against harmful interference in a residential installation, and are more stringent than “outdoor” requirements. Operation of this device is subject to the following conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment generates, uses, and can radiate radio frequency energy and may cause harmful interference to radio communications if not installed and used in accordance with the instructions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and the receiver. • Connect the equipment into an outlet that is on a different circuit from the GPS device. • Consult the dealer or an experienced radio/TV technician for help. This product does not contain any user-serviceable parts. Repairs should only be made by an authorized Garmin service center. Unauthorized repairs or modifications could result in permanent damage to the equipment, and void your warranty and your authority to operate this device under Part 15 regulations. Product Environmental Programs Information about Garmin’s product recycling program and WEEE, RoHS, REACH, and other compliance programs can be found at www.garmin.com/aboutGarmin/environment. Informations importantes relatives au produit et à la sécurité Déclaration de conformité Par la présente, Garmin déclare que ce produit est conforme aux principales exigences et autres clauses pertinentes de la directive européenne 1999/5/CE. Pour prendre connaissance de l’intégralité de la déclaration de conformité, rendez-vous sur le site www.garmin.com/compliance. Conformité aux normes d’Industrie Canada Les appareils de radiocommunication de catégorie I sont conformes à la norme RSS-210 d’Industrie Canada. Les appareils de radiocommunication de catégorie II sont conformes à la norme RSS-310 d’Industrie Canada. Cet appareil est conforme aux normes RSS sans licence d’Industrie Canada. Son fonctionnement est soumis aux conditions suivantes : (1) cet appareil ne doit pas causer d’interférences et (2) doit accepter toute interférence, y compris les interférences pouvant entraîner un fonctionnement indésirable de l’appareil. Programmes environnementaux Des informations relatives au programme Garmin de recyclage des produits ainsi qu’aux directives DEEE et RoHS, à la réglementation REACH et aux autres programmes de conformité sont disponibles à l’adresse www.garmin.com/aboutGarmin/environment. Informazioni importanti sulla sicurezza e sul prodotto Dichiarazione di conformità Con il presente documento, Garmin dichiara che questo prodotto è conforme ai requisiti essenziali e alle altre disposizioni in materia previste dalla Direttiva 1999/5/CE. Per visualizzare l’intero documento della Dichiarazione di conformità, visitare il sito Web www.garmin.com/compliance. Programmi ambientali per i prodotti Le informazioni sul programma di riciclo dei prodotti Garmin, sulle direttive WEEE, RoHS, REACH e su altri programmi di conformità sono disponibili sul sito Web www.garmin.com/aboutGarmin/environment. Wichtige Sicherheits- und Produktinformationen Konformitätserklärung Garmin erklärt hiermit, dass dieses Produkt den wesentlichen Anforderungen und weiteren relevanten Vorschriften der Direktive 1999/5/EG entspricht. Sie finden die vollständige Konformitätserklärung auf der Garmin-Website für Ihr Produkt von Garmin unter www.garmin.com/compliance. Umweltschutzprogramme für das Produkt Informationen zum Produktrecyclingprogramm von Garmin sowie zur WEEE-, RoHS- und REACH-Richtlinie und zu anderen Programmen zur Einhaltung von Richtlinien finden Sie unter www.garmin.com/aboutGarmin /environment. Información importante sobre el producto y tu seguridad Declaración de conformidad Por la presente, Garmin declara que este producto cumple con los requisitos esenciales y otras disposiciones relevantes de la Directiva 1999/5/CE. Para ver la Declaración de conformidad completa, visita el sitio Web de Garmin correspondiente al producto específico: www.garmin.com/compliance. Programas medioambientales para el producto Puedes consultar información acerca del programa de reciclado de productos de Garmin y la directiva WEEE, RoHS y REACH, así como de otros programas de cumplimiento en www.garmin.com/aboutGarmin /environment. Informações importantes de segurança e do produto Declaração de Conformidade Por este meio, a Garmin declara que esta unidade cumpre os requisitos fundamentais e restantes provisões aplicáveis constantes da Directiva 1999/5/CE. Para consultar a Declaração de Conformidade integral, visite o Web site des…

Text truncated - open the document above for the full version.

Page 1 of 2 January 12, 2013 Timco Engineering Inc. 849 NW State Road 45 Newberry, FL 32669 Applicant: Garmin International, Inc. 1200 East 151st Street Olathe, KS 66062 Re: Confidentiality for submittal information regarding FCC ID number IPH-M2AINX01 PRODUCT: Low power Transmitters operated under paragraph 15.249. Dear Sirs: Garmin International, Inc. requests that the material in the Parts List, Schematics, Block Diagram, and Operational Description be withheld from public disclosure pursuant to Sections 0.457 and 0.459 of the Commission’s Rules following grant of the application. In support of this request, Garmin International, Inc. submits the following information. CONFIDENTIAL FILES Conf BlkDia M2AINX01.pdf Conf OpDes M2AINX01.pdf Conf Schem M2AINX01.pdf 1. Identification of the specific information for which confidential treatment is sought: The materials set forth in the Operational Description, block diagram, parts list, and Schematics, which are segregated, from the non-confidential exhibits of the application, are those for which confidentiality is sought. 2. Identification of the Commission proceeding in which the information was submitted or a description of the circumstances giving rise to the submission: The proceeding is that involving the application for equipment authorization (certification) under FCC ID No: IPH-M2AINX01 3. Explanation of the degree to which the information is commercial or financial, or contains a trade secret or is privileged: This material includes a detailed theory of operation, circuit diagrams, and schematic. As such, this material is treated as highly confidential business information. ROGERS LABS, INC. 4405 West 259 th Terrace Louisburg, KS 66053 913 837-3214 Page 2 of 2 4. Explanation of the degree to which the information concerns a service that is subject to competition: The material for which confidentiality is sought is employed in the design and manufacture of this transmitting equipment that is offered on a highly competitive basis. Customers for this equipment have a variety of competing sources. 5. Explanation of how disclosure of the information could result in substantial competitive harm: Disclosure would, in effect, give away the fruits of the labors of Garmin International, Inc.’s engineering personnel, who have designed the equipment and the manufacturing process. Disclosure would also offer competitors additional unwarranted insight into the state of the product development, thereby allowing competitors an advantage, not available to Garmin International, Inc. 6. Identification of any measures taken by the submitting party to prevent unauthorized disclosure: The information for which confidential treatment is sought is kept confidential by Garmin International, Inc. and not made available to third parties except pursuant to non-disclosure agreements. 7. Identification of whether the information is available to the public and the extent of any previous disclosure of the information to third parties: To the knowledge of those preparing this application, the information has not been disclosed publicly heretofore. While the general theory of operation of this equipment has been the subject of numerous disclosures in industry and standards groups as well as in rule making proceedings of the FCC, the protection sought is narrowly drawn and pertains to certain specific implementations of this radio technology. 8. Justification of the period during which the submitting party asserts that the material should not be available for public disclosure: This material should not be disclosed for at least 25 years. While improvements in design are made relatively frequently, disclosure of the design information would lead to insights into both design and manufacturing techniques that could have an adverse competitive effect for many years to come. As such, it is important that the design not be made available to unauthorized persons who might attempt to use knowledge of the design to compromise the applications for which the equipment will be employed. Should you require any further information, please contact the undersigned. Thank you for your consideration in this matter. Sincerely, Scot Rogers

January 12, 2013 Timco Engineering Inc. 849 NW State Road 45 Newberry, FL 32669 Applicant: Garmin International, Inc. Equipment: FCC ID: IPH-M2AINX01 1200 East 151st Street CORES number: 0005-0885-88 Olathe, KS 66062 FCC Rules: Parts 2 and 15.249 To Whom It May Concern: The form 731 and application have been electronically submitted and any attachments will be up loaded to your web site for use in obtaining a grant of certification. Confidentiality is requested as outlined below. Permanent Garmin International, Inc. requests that the material in the Parts List, Schematics, block diagram, and Operational Description be withheld from public disclosure pursuant to Sections 0.457 and 0.459 of the Commission’s Rules following grant of the application. A statement of confidentiality will be attached with the application at the time of submittal. Exhibit File Schematics Conf Schem M2AINX01.pdf Block diagram Conf BlkDia M2AINX01.pdf Operational Description Conf OpDes M2AINX01.pdf Should you require any further information, please contact the undersigned. Thank you for your consideration in this matter. Sincerely, Scot Rogers Rogers Labs, Inc. Enclosures ROGERS LABS, INC. 4405 West 259 th Terrace Louisburg, KS 66053 Phone / Fax (913) 837-3214

Rogers Labs, Inc. Garmin International, Inc. FCC ID: IPH-M2AINX01 4405 West 259 th Terrace Model: M2AINX01 IC: 1792A-M2AINX01 Louisburg, KS 66053 Test #:121120W SN: HBB00397 Phone/Fax: (913) 837-3214 Test to: FCC CFR 47 15.249, RSS 210 Date: January 14, 2013 Revision 1 File: LabelSmpl M2AINX01 Page 1 of 1 ID label and location Label placement

Rogers Labs, Inc. Garmin International, Inc. FCC ID: IPH-M2AINX01 4405 West 259 th Terrace Model: M2AINX01 IC: 1792A-M2AINX01 Louisburg, KS 66053 Test #:121120W SN: HBB00397 Phone/Fax: (913) 837-3214 Test to: FCC CFR 47 15.249, RSS 210 Date: January 12, 2013 Revision 1 File: IntPho M2AINX01 Page 1 of 1 Internal Photographs

NVLAP Lab Code 200087-0 Rogers Labs, Inc. Garmin International, Inc. FCC ID: IPH-M2AINX01 4405 West 259 th Terrace Model: M2AINX01 IC: 1792A-M2AINX01 Louisburg, KS 66053 Test #:121120W SN: HBB00397 Phone/Fax: (913) 837-3214 Test to: FCC CFR 47 15.249, RSS 210 Date: January 12, 2013 Revision 1 File: M2AINX01 TstRpt 121120W Page 1 of 28 Test Report for Grant of Certification Application FOR Garmin International, Inc. 1200 East 151st Street Olathe, KS 66062 Model: M2AINX01 Low Power Transmitter FCC ID: IPH-M2AINX01 IC: 1792A-M2AINX01 Test Report Number 121120W Authorized Signatory: Scot D. Rogers NVLAP Lab Code 200087-0 Rogers Labs, Inc. Garmin International, Inc. FCC ID: IPH-M2AINX01 4405 West 259 th Terrace Model: M2AINX01 IC: 1792A-M2AINX01 Louisburg, KS 66053 Test #:121120W SN: HBB00397 Phone/Fax: (913) 837-3214 Test to: FCC CFR 47 15.249, RSS 210 Date: January 12, 2013 Revision 1 File: M2AINX01 TstRpt 121120W Page 2 of 28 Test Report for Application of Certification For GARMIN INTERNATIONAL, INC. 1200 East 151st Street Olathe, KS 66062 Phone: (913) 397-8200 Mr. Van Ruggles Director of Quality Assurance Model: M2AINX01 Low Power Transmitter Frequency Range: 2,405-2,480 MHz FCC ID: IPH-M2AINX01 IC: 1792A-M2AINX01 Test Report Number: 121120W Test Date: November 20, 2012 Authorized Signatory: Scot D. Rogers Rogers Labs, Inc. 4405 West 259th Terrace Louisburg, KS 66053 Telephone/Facsimile: (913) 837-3214 This report shall not be reproduced except in full, without the written approval of the laboratory. This report must not be used by the client to claim product endorsement by NVLAP, NIST, or any agency of the Federal Government. ROGERS LABS, INC. 4405 West 259 th Terrace Louisburg, KS 66053 Phone / Fax (913) 837-3214 NVLAP Lab Code 200087-0 Rogers Labs, Inc. Garmin International, Inc. FCC ID: IPH-M2AINX01 4405 West 259 th Terrace Model: M2AINX01 IC: 1792A-M2AINX01 Louisburg, KS 66053 Test #:121120W SN: HBB00397 Phone/Fax: (913) 837-3214 Test to: FCC CFR 47 15.249, RSS 210 Date: January 12, 2013 Revision 1 File: M2AINX01 TstRpt 121120W Page 3 of 28 Table of Contents TABLE OF CONTENTS .................................................................................................... 3 REVISIONS ....................................................................................................................... 4 FORWARD ....................................................................................................................... 5 OPINION / INTERPRETATION OF RESULTS ................................................................. 5 ENVIRONMENTAL CONDITIONS.................................................................................... 5 STATEMENT OF MODIFICATIONS AND DEVIATIONS ................................................. 5 APPLICATION FOR CERTIFICATION ............................................................................. 6 EQUIPMENT TESTED SETUP, FUNCTION AND CONFIGURATIONS .......................... 7 Equipment Function and Test Setup ....................................................................................................................... 7 EUT Configuration ................................................................................................................................................... 7 LIST OF TEST EQUIPMENT ............................................................................................ 8 UNITS OF MEASUREMENTS .......................................................................................... 9 TEST SITE LOCATIONS .................................................................................................. 9 APPLICABLE STANDARDS & TEST PROCEDURES .................................................... 9 AC Line Conducted Emission Test Procedure ....................................................................................................... 10 Diagram 1 Test arrangement for Conducted emissions .......................................................................................... 10 Radiated Emission Test Procedure ......................................................................................................................... 11 Diagram 2 Test arrangement for radiated emissions of tabletop equipment .......................................................... 12 Diagram 3 Test arrangement for radiated emissions tested on Open Area Test Site (OATS) ............................... 13 INTENTIONAL RADIATORS ............................................................................................ 13 Antenna Requirements ............................................................................................................................................. 13 Restricted Bands of Operation ................................................................................................................................ 14 Table 1 Radiated Emissions in Restricted Bands Data (worst-case) .................................................................... 14 Summary of Results for Radiated Emissions in Restricted Bands ....................................................................... 15 General Radiated EMI Testing Procedure ............................................................................................................. 15 Table 2 General Radiated Emissions from EUT Data (Highest Emissions) ........................................................ 16 Summary of Results for General Radiated Emissions ........................................................................................... 16 NVLAP Lab Code 200087-0 Rogers Labs, Inc. Garmin International, Inc. FCC ID: IPH-M2AINX01 4405 West 259 th Terrace Model: M2AINX01 IC: 1792A-M2AINX01 Louisburg, KS 66053 Test #:121120W SN: HBB00397 Phone/Fax: (913) 837-3214 Test to: FCC CFR 47 15.249, RSS 210 Date: January 12, 2013 Revision 1 File: M2AINX01 TstRpt 121120W Page 4 of 28 Operation in the Band 2,400-2,483.5 MHz ...............…

Text truncated - open the document above for the full version.

Rogers Labs, Inc. Garmin International, Inc. FCC ID: IPH-M2AINX01 4405 West 259 th Terrace Model: M2AINX01 IC: 1792A-M2AINX01 Louisburg, KS 66053 Test #:121120W SN: HBB00397 Phone/Fax: (913) 837-3214 Test to: FCC CFR 47 15.249, RSS 210 Date: January 12, 2013 Revision 1 File: TSup M2AINX01 Page 1 of 1 Test setup photographs