JCK-GN-WI01HTMini PCI Wireless Adapter

GN-WI01HT IEEE 802.11a/b/g Mini-PCI Wireless LAN Card User’s Manual http://www.gigabyte.com.tw Rev. 1.0 First Edition Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. If this device is going to be operated in 5.15~5.25GHz frequency range, then it is restricted in indoor environment only. This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2)The antenna should use a unique coupling to ensure that no antenna other than that funished by the responsible party shall be used with the device. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. 1. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users (for example : Wireless Router. Access point...etc.). The final end product must be labeled in a visible area with the following: “Contains TX FCC ID: JCK-GN-WI01HT”. 2. Manual Information That Must be Included The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrate this module. The users manual for OEM integrators end users must include the following information in a prominent location “ IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter”. If the end product integrating this module is going to be operated in 5.15 ~ 5.25GHz frequency range, the warning statement in the user manual of the end product should include the following "Within 5.15-5.25GHz band, U-NII devices will be restricted to indoor operations to reduce any potential for harmful interterence to co-channel MSS operations. Usage of this device outdoor could void the user’s authority to operate the equipment." GIGABYTE declares that GN-WI01HT ( FCC ID: JCK-GN-WI01HT) is limited in CH1~CH11 for 2.4GHz by specified firmware controlled in U.S.A. Contents CHAPTER 1 PRODUCT OVERVIEW 1 1-1. INTRODUCTION........................................................................................................................1 1-2. FEATURES...............................................................................................................................1 1-3. PHYSICAL DIMENSIONS/PACKAGING......................................................................................1 1-4. SYSTEM REQUIREMENTS........................................................................................................1 CHAPTER 2 INSTALLING THE WLAN CARD 2 2-1. INSTALLING THE DRIVER & UTILITY (WIN98SE/ME)............................................................2 2-2. INSTALLING THE DRIVER & UTILITY (WIN2000/XP)..............................................................8 CHAPTER 3 USING THE UTILITY 12 3-1. LINK STATUS.......................................................................................................................12 3-2. SITE SURVEY......................................................................................................................16 3-3. CONFIGURATION.................................................................................................................17 3-4. STATISTICS..........…

Text truncated - open the document above for the full version.

FCC ID: JCK-GN-WI01HT ADT No. 940620L09 Modular Approval Request Letter Advance Data Technology 14 July 2005 Dear Application Examiner, GIGA-BYTE TECHNOLOGY CO., LTD, It’s Mini PCI Wireless Adapter, FCC ID: JCK-GN-WI01HT, would like to have your authorization as a limited modular approval specific to the mobile device such as Access Point. The requirements of Public Notice DA00-1407 have been met and shown on the following statements. 1. “The modular transmitter must have its own RF shielding.”: The radio portion of this module has been shielded, please see exhibition External Photo. 2. “The modular transmitter must have buffered modulation/data inputs.” The EUT has buffered data inputs, it is integrated in chip AR5414A-00. 3. “The modular transmitter must have its own power supply regulation.” The chips IF converter and RF/IF converter which will influence the frequency radiation, have to be 1.80Vdc powered. The mini-pci interface provides 3.3Vdc, so there are regulators in front of these chips, the part number of this regulator is AR5414A-00. 4. “The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(C).” The EUT meets the FCC antenna requirements. The spurious emission, unique antenna connector and photo of antennas are shown in the test report. 5. “The modular transmitter must be tested in a stand-alone configuration” The EUT was tested in a stand-alone configuration via a PCMCIA to mini-PCI extender. Please see section Photographs of Test Configuration in the test report, the EUT was plugged in this extender. 6. “The modular transmitter must be labeled with its own FCC ID number.” Please see exhibition Label Sample for the FCC ID of this module. And also in the exhibition Users Manual, there are instructions give to the OEM on how to label the end product. FCC ID: JCK-GN-WI01HT ADT No. 940620L09 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.” The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are given in the Users Manual. 8. “The modular transmitter must comply with any applicable RF exposure requirements.” The EUT is compliant with all applicable RF exposure requirements. RF Exposure is addressed in the RF exposure exhibition. Please contact me if you have any further questions. Thanks for your attention. Best Regards, Cody Chang Deputy Manager Advance Data Technology

Page 1 CONSTRUCTION PHOTOS OF EUT

FCC ID : JCK-GN-WI01HT Label Location

Page 2 Page 3

FCC ID: JCK-GN-WI01HT Report No.RF940620L09 Technical Description This device is a Mini PCI Wireless Adapter which operates in both of the 5GHz and 2.4GHz bands and can’t transmitting simultaneously, the maximum data rate could be 108Mbps. The transmitter of the EUT is powered by host equipment. The antenna used in this product is Dipole antenna with UFL antenna connector. For more detailed instruction, please take a look at the user’s manual. FCC 15.407(c) states: The device shall automatically discontinue transmission in case of either absence of information to transmit or operational failure. These provisions are not intended to preclude the transmission of control or signaling information or the use of repetitive codes used by certain digital technologies to complete frame or burst intervals. Applicants shall include in their application for equipment authorization a description of hoe this requirement is met” Data transmission is always initiated by software, which is then pass down through the MAC, through the digital and analog baseband, and finally to the RF chip. Several special packets (ACKs, CTS, PSPoll, etc...) are initiated by the MAC. There are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only while one of the aforementioned packets are being transmitted.

FCC ID: JCK-GN-WI01HT Report No: SA940620L09 1 RF EXPOSURE REPORT REPORT NO.: SA940620L09 MODEL NO.: GN-WI01HT ACCORDING: FCC Guidelines for Human Exposure IEEE C95.1 APPLICANT: GIGA-BYTE TECHNOLOGY CO., LTD. ADDRESS: No. 6, Bau Chiang Road, Hsin-Tien, Taipei Hsien, Taiwan, ROC ISSUED BY: Advance Data Technology Corporation LAB ADDRESS: No. 47, 14th Ling, Chia Pau Tsuen, Lin Kou Hsiang 244, Taipei Hsien, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd., Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. FCC ID: JCK-GN-WI01HT Report No: SA940620L09 2 RF Exposure Measurement (Mobile Device) 1. Introduction In this document, we try to prove the safety of radiation harmfulness to the human body for our product. The limit for Maximum Permissible Exposure (MPE) specified in FCC 1.1310 is followed. The Gain of the antenna used in this product is measured in a Fully Anechoic Chamber (FAC) calibrated for antenna measurement in ADT, and also the maximum total power input to the antenna is measured. Through the Friis transmission formula and the maximum gain of the antenna, we can calculate the distance, away from the product, where the limit of MPE is reached. Although the Friis transmission formula is a far field assumption, the calculated result of that is an over-prediction for near field power density. We will take that as the worst case to specify the safety range. 2. RF Exposure Limit According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environmental impact of human exposure to radio-frequency (RF) radiation as specified in 1.1307(b) LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (minutes) (A)Limits For Occupational / Control Exposures 300-1500......F/3006 1500-100,000......56 (B)Limits For General Population / Uncontrolled Exposure 300-1500......F/15006 1500-100,000......1.030 F = Frequency in MHz FCC ID: JCK-GN-WI01HT Report No: SA940620L09 3 3. Friis Formula Friis transmission formula : Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm If we know the maximum Gain of the antenna and the total power input to the antenna, through the calculation, we will know the MPE value at distance r. Ref. : David K. Cheng, Field and Wave Electromagnetics, Second Edition, Page 640, Eq. (11-133). 4. EUT Operating condition The software provided by Manufacturer enabled the EUT to transmit and receive data at lowest, middle and highest channel individually. 5. Classification This device is not fixed inside the host equipment, it is connected with host through wire. So it is easy to be re-located in the place where at least 20cm far away from the body of the user. Warning statement to the user for keeping at least 20cm or more separation distance with the antenna should be included in users manual. So, this device is classified as Mobile Device. FCC ID: JCK-GN-WI01HT Report No: SA940620L09 4 6. Test Results 6.1 Antenna Gain The maximum Gain measured in Fully Anechoic Chamber is 1.8dBi or 1.5136 (numeric) (for 2.4GHz band), 1.2dBi or 1.3183 (numeric) (for 5.0GHz band) 6.2 Output Power Into Antenna & RF Exposure value at distance 20cm: 802.11b DSSS modulation Channel Channel Frequency (MHz) Output Power to Antenna (mW) Power Density (mW/cm 2 ) Limit of Power Density (mW/cm 2 ) 1241239.9020.0121.0 6243745.0820.0141.0 11246244.8750.0141.0 802.11g OFDM modulation Channel Channel Frequency (MHz) Output Power to Antenna (mW) Power Density (mW/cm 2 ) Limit of Power Density (mW/cm 2 ) 1241222.5420.0071.0 6243746.0260.0141.0 11246222.4390.0071.0 802.11g Turbo OFDM modulation Channel Channel Frequency (MHz) Output Power to Antenna (mW) Power Density (mW/cm 2 ) Limit of Power Density (mW/cm 2 ) 6243735.7270.0111.0 FCC ID: JCK-GN-WI01HT Report No: SA940620L09 5 802.11a OFDM modulation Channel Channel Frequency (MHz) Output Power to Antenna (mW) Power Density (mW/cm 2 ) Limit of Power Density (mW/cm 2 ) 1518029.1740.0081.0 4524028.1840.0071.0 5526029.8540.0081.0 8532025.2350.0071.0 9574528.3790.0071.0 11578526.5460.0071.0 12580527.7330.0071.0 802.11a Turbo OFDM modulation Channel Channel Frequency (MHz) Output Power to Antenna (mW) Power Density (mW/cm 2 ) Limit of Power Density (mW/cm 2 ) 1521025.2350.0071.0 2525025.4100.0071.0 3529019.9990.0051.0 4576019.9990.0051.0 5580027.4160.0071.0

FCC ID: JCK-GN-WI01HT Report No.: RF940620L091Report Format Version 2.0.2 FCC TEST REPORT (15.247) REPORT NO.: RF940620L09 MODEL NO.: GN-WI01HT RECEIVED: May 16, 2005 TESTED: May 16 ~ Jul. 01, 2005 ISSUED: Jul. 04, 2005 APPLICANT: GIGA-BYTE TECHNOLOGY CO., LTD. ADDRESS: No. 6, Bau Chiang Road, Hsin-Tien, Taipei Hsien, Taiwan, ROC. ISSUED BY: Advance Data Technology Corporation LAB ADDRESS: No. 47, 14 th Ling, Chia Pau Tsuen, Lin Kou Hsiang 244, Taipei Hsien, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2 nd Rd., Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 117 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by CNLA, A2LA or any government agencies. The test results in the report only apply to the tested sample. 0528 ILAC MRA FCC ID: JCK-GN-WI01HT Report No.: RF940620L092Report Format Version 2.0.2 Table of Contents 1.CERTIFICATION ......................................................................................................5 2.SUMMARY OF TEST RESULTS ..............................................................................6 2.1 MEASUREMENT UNCERTAINTY ...........................................................................6 3.GENERAL INFORMATION.......................................................................................7 3.1GENERAL DESCRIPTION OF EUT.........................................................................7 3.2DESCRIPTION OF TEST MODES...........................................................................8 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST ...................................................... 9 3.2.2 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL: ........................ 10 3.3GENERAL DESCRIPTION OF APPLIED STANDARDS ........................................12 3.4DESCRIPTION OF SUPPORT UNITS ...................................................................12 4.TEST TYPES AND RESULTS (802.11b & g 2412~2462MHz BAND)....................13 4.1CONDUCTED EMISSION MEASUREMENT .........................................................13 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT....................................... 13 4.1.2 TEST INSTRUMENTS............................................................................................ 13 4.1.3 TEST PROCEDURES ............................................................................................ 14 4.1.4 DEVIATION FROM TEST STANDARD .................................................................. 14 4.1.5 TEST SETUP ......................................................................................................... 15 4.1.6 EUT OPERATING CONDITIONS ........................................................................... 15 4.1.7 TEST RESULTS ..................................................................................................... 16 4.2RADIATED EMISSION MEASUREMENT ..............................................................22 4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT............................................ 22 4.2.2 TEST INSTRUMENTS............................................................................................ 23 4.2.3 TEST PROCEDURES ............................................................................................ 24 4.2.4 DEVIATION FROM TEST STANDARD .................................................................. 24 4.2.5 TEST SETUP ......................................................................................................... 25 4.2.6 EUT OPERATING CONDITIONS ........................................................................... 25 4.2.7 TEST RESULTS ..................................................................................................... 26 4.36dB BANDWIDTH MEASUREMENT .....................................................................34 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT ................................................... 34 4.3.2 TEST INSTRUMENTS............................................................................................ 34 4.3.3 TEST PROCEDURE............................................................................................... 35 4.3.4 DEVIATION FROM TEST STANDARD .................................................................. 35 4.3.5 TEST SETUP ......................................................................................................... 35 4.3.6 EUT OPERATING CONDITIONS ........................................................................... 35 4.3.7 TEST RESULTS ..................................................................................................... 36 4.4MAXIMUM PEAK OUTPUT POWER .....................................................................44 4.4.1 LIMITS OF MAXIMUM PEAK OUTPUT POWER MEASUREMENT ...................... 44 4.4.2 INSTRUMENTS...................................................................................................... 44 4.4.1 TEST PROCEDURES ............................................................................................ 45 4.4.2 DEVIATION FROM TEST STANDARD .................................................................. 45 4.4.3 TEST SETUP ......................................................................................................... 45 4.4.4 EUT OPERATING CONDITIONS ........................................................................... 45 FCC ID: JCK-GN-WI01HT Report No.: RF940620L093Report Format Version 2.0.2 4.4.3 TEST RESULTS ..................................................................................................... 46 4.5POWER SPECTRAL DENSITY MEASUREMENT.................................................48 4.5.1 LIMITS OF POWER SPECTRAL DENSITY MEASUREMENT .............................. 48 4.5.2 TEST…

Text truncated - open the document above for the full version.

FCC ID: JCK-GN-WI01HT Report No.: RF940620L0971Report Format Version 2.0.2 4.7 ANTENNA REQUIREMENT 4.7.1 STANDARD APPLICABLE For intentional device, according to FCC 47 CFR Section 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. And according to FCC 47 CFR Section 15.247 (b), if transmitting antennas of directional gain greater than 6dBi are used, the power shall be reduced by the amount in dB that the directional gain of the antenna exceeds 6dBi. 4.7.2 ANTENNA CONNECTED CONSTRUCTION The antenna used in this product is Dipole antenna with UFL antenna connector. The maximum Gain of the antenna is 1.8dBi. FCC ID: JCK-GN-WI01HT Report No.: RF940620L0972Report Format Version 2.0.2 5. TEST TYPES AND RESULTS (802.11a 5725~5850MHz Band) 5.1 CONDUCTED EMISSION MEASUREMENT 5.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT FREQUENCY OF EMISSION (MHz)CONDUCTED LIMIT (dBμV) Quasi-peakAverage 0.15-0.5 0.5-5 5-30 66 to 56 56 60 56 to 46 46 50 NOTE:1. The lower limit shall apply at the transition frequencies. 1. The limit decreases in line with the logarithm of the frequency in the range of 0.15 to 0.50 MHz. 2. All emanations from a class A/B digital device or system, including any network of conductors and apparatus connected thereto, shall not exceed the level of field strengths specified above. 5.1.2 TEST INSTRUMENTS DESCRIPTION & MANUFACTURERMODEL NO.SERIAL NO.CALIBRATED UNTIL Test Receiver ROHDE & SCHWARZ ESCS30100291Nov. 16, 2005 RF signal cable Woken 5D-FBCable-HYC01-01Jan. 09, 2006 LISN SCHWARZBECK NNBL 8226-28226-142May 02, 2006 LISN ROHDE & SCHWARZ ESH2-Z5100104Feb. 15, 2006 Software ADT ADT_Cond_V3NANA NOTE: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in HwaYa Shielded Room 1. 3. The VCCI Site Registration No. is C-2040. FCC ID: JCK-GN-WI01HT Report No.: RF940620L0973Report Format Version 2.0.2 5.1.3 TEST PROCEDURES a. The EUT was placed 0.4 meters from the conducting wall of the shielded room with EUT being connected to the power mains through a line impedance stabilization network (LISN). Other support units were connected to the power mains through another LISN. The two LISNs provide 50 ohm/ 50uH of coupling impedance for the measuring instrument. b. Both lines of the power mains connected to the EUT were checked for maximum conducted interference. c. The frequency range from 150kHz to 30MHz was searched. Emission levels under (Limit – 20dB) was not recorded. 5.1.4 DEVIATION FROM TEST STANDARD No deviation FCC ID: JCK-GN-WI01HT Report No.: RF940620L0974Report Format Version 2.0.2 5.1.5 TEST SETUP For the actual test configuration, please refer to the related item – Photographs of the Test Configuration. 5.1.6 EUT OPERATING CONDITIONS Same as 4.1.6 Horizontal Ground Reference Plane Vertical Ground Reference Plane FCC ID: JCK-GN-WI01HT Report No.: RF940620L0975Report Format Version 2.0.2 5.1.7 TEST RESULTS Conducted Worst-Case Data EUT Mini PCI Wireless Adapter MEASUREMENT DETAIL MODEL GN-WI01HT PHASE Line 1 CHANNEL Channel 3 6dB BANDWIDTH 9 kHz MODULATION TYPE BPSK ENVIRONMENTAL CONDITIONS 25deg. C, 66%RH, 991hPa TRANSFER RATE 6Mbps INPUT POWER (SYSTEM) 120Vac, 60 Hz TESTED BY Richard Chen Freq.Corr. Reading Value Emission Level LimitMargin NoFactor[dB (uV)][dB (uV)][dB (uV)](dB) [MHz](dB)Q.P.AV.Q.P.AV.Q.P.AV.Q.P.AV. 10.2090.1144.04-44.15-63.2653.26-19.11- 20.3100.1128.66-28.77-59.9749.97-31.20- 31.4780.2517.62-17.87-56.0046.00-38.13- 44.3950.4018.69-19.09-56.0046.00-36.91- 59.3910.5224.19-24.71-60.0050.00-35.29- 620.7541.0822.32-23.40-60.0050.00-36.60- REMARKS: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. "-": The Quasi-peak reading value also meets average limit and measurement with the average detector is unnecessary. 3. The emission levels of other frequencies were very low against the limit. 4. Margin value = Emission level - Limit value 5. Correction factor = Insertion loss + Cable loss 6. Emission Level = Correction Factor + Reading Value. FCC ID: JCK-GN-WI01HT Report No.: RF940620L0976Report Format Version 2.0.2 EUT Mini PCI Wireless Adapter MEASUREMENT DETAIL MODEL GN-WI01HT PHASE Line 2 CHANNEL Channel 3 6dB BANDWIDTH 9 kHz MODULATION TYPE BPSK ENVIRONMENTAL CONDITIONS 25deg. C, 66%RH, 991hPa TRANSFER RATE 6Mbps INPUT POWER (SYSTEM) 120Vac, 60 Hz TESTED BY Richard Chen Freq.Corr. Reading Value Emission Level LimitMargin NoFactor[dB (uV)][dB (uV)][dB (uV)](dB) [MHz](dB)Q.P.AV.Q.P.AV.Q.P.AV.Q.P.AV. 10.2050.1144.16-44.27-63.4253.42-19.15- 20.3110.1128.78-28.89-59.9549.95-31.06- 31.6760.2519.71-19.96-56.0046.00-36.04- 42.4020.2920.40-20.69-56.0046.00-35.31- 59.4690.4423.42-23.86-60.0050.00-36.14- 621.0980.7621.96-22.72-60.0050.00-37.28- REMARKS: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. "-": The Quasi-peak reading value also meets average limit and measurement with the average detector is unnecessary. 3. The emission levels of other frequencies were very low against the limit. 4. Margin value = Emission level - Limit value 5. Correction factor = Insertion loss + Cable loss 6. Emission Level = Correction Factor + Reading Value. FCC ID: JCK-GN-WI01HT Report No.: RF940620L0977Report Format Version 2.0.2 5.2 RADIATED EMISSION MEASUREMENT 5.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT Emissions radiated outside of the specified bands, shall be according to the general radiated limits in 15.209 as following: Frequencies (MHz) Field strength (microvolts/meter) Measurement distance (meters) 0.009-0.4902400/F(kHz)300 0.490-1.70524000/F(kHz)30 1.705-30.03030 30-881003 88-2161503 216-9602003 Above 9605003 NOTE: 1. The lower limit shall apply at the transition frequencies. 2. Emission level (dBuV/m) = 20 log Emission level (uV/m). 3. As shown in 15.35(b), for frequencies above 1000MHz, the field strength limits are…

Text truncated - open the document above for the full version.

FCC ID: JCK-GN-WI01HT Report No.: RF940620L091Report Format Version 2.0.2 FCC TEST REPORT (15.407) REPORT NO.: RF940620L09 MODEL NO.: GN-WI01HT RECEIVED: May 16, 2005 TESTED: May 16 ~ Jul. 01, 2005 ISSUED: Jul. 05, 2005 APPLICANT: GIGA-BYTE TECHNOLOGY CO., LTD. ADDRESS: No. 6, Bau Chiang Road, Hsin-Tien, Taipei Hsien, Taiwan, ROC. ISSUED BY: Advance Data Technology Corporation LAB ADDRESS: No. 47, 14 th Ling, Chia Pau Tsuen, Lin Kou Hsiang 244, Taipei Hsien, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2 nd Rd., Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 75 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by CNLA, A2LA or any government agencies. The test results in the report only apply to the tested sample. 0528 ILAC MRA No. 2177-01 FCC ID: JCK-GN-WI01HT Report No.: RF940620L092Report Format Version 2.0.2 Table of Contents 1.CERTIFICATION ......................................................................................................4 2.SUMMARY OF TEST RESULTS ..............................................................................5 2.1 MEASUREMENT UNCERTAINTY ...........................................................................5 3.GENERAL INFORMATION.......................................................................................6 3.1GENERAL DESCRIPTION OF EUT.........................................................................6 3.2DESCRIPTION OF TEST MODES...........................................................................7 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST ...................................................... 8 3.2.2 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL: .......................... 9 3.3GENERAL DESCRIPTION OF APPLIED STANDARDS ........................................ 11 3.4DESCRIPTION OF SUPPORT UNITS ................................................................... 11 4.TEST TYPES AND RESULTS (5150 ~ 5350MHz BAND)......................................12 4.1CONDUCTED EMISSION MEASUREMENT .........................................................12 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT....................................... 12 4.1.2 TEST INSTRUMENTS............................................................................................ 12 4.1.3 TEST PROCEDURES ............................................................................................ 13 4.1.4 DEVIATION FROM TEST STANDARD .................................................................. 13 4.1.5 TEST SETUP ......................................................................................................... 14 4.1.6 EUT OPERATING CONDITIONS ........................................................................... 14 4.1.7 TEST RESULTS ..................................................................................................... 15 4.2RADIATED EMISSION MEASUREMENT ..............................................................17 4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT............................................ 17 4.2.2 LIMITS OF UNWANTED EMISSION OUT OF THE RESTRICTED BANDS…

Text truncated - open the document above for the full version.