1 TRANSMITTER’S MANUAL ITEM NO.: 30113 INSTALLATION OF THE TRANSMITTER BATTERY’S SETUP Please use eight “AA” alkaline batteries or rechargeable batteries. First: In light of arrow’s direction, push the cover of battery case away, and lift it to sever the transmitter. Second: Insert eight batteries and pay attention to batteries’ anode and cathode. Third: push the cover of battery case to original place. Note: If using rechargeable batteries, you should use the intelligent charger(No.40108). Its charging range is 1H—1.5H. INDICATOR LIGHT If having full electric energy in the transmitter, the green, the red, and the yellow light will all on. If the green light goes out, it indicates the electric energy is not full, and possibly have half one. If the yellow light blinks, it indicates the electric energy is not full, and you should replace or recharge the batteries. If the red light brights, you should replace or recharge the batteries. 2 EXPLANATION OF TRANSMITTER’S ANTENNA Before turning on the transmitter, you should ensure if the antenna is set up correctly, and is extended enough, Otherwise it will affect the range of control largely, possible cause damage to your model, or injuries yourself and someone else. INSTALLATION OF THE RECEIVER AND THE SERVO Before installation, please read these following instructions carefully in order to avoid the dispensiable loss to yourself and some else. Never let the receiver and the motor or the engine use one power supply together. 1. Check if the switch of the receiver’s power supply is set on the “OFF” position. 2. Set the switch of the receiver’s power supply to the circuit way of the receiver’s power supply. 3. Set the throttle’s servo to the second channel of the receiver. 4. Set the turnable servo to the first channel of the receiver. 5. Insert four “AA” alkaline batteries to the battery case, and connect the ports to the switch of the receiver. 6. Check if the frequency of the receiver crystal matches up to the one of the transmitter crystal. 7. Turn on the transmitter. 3 8. Set the switch of the receiver to “ON” position. WARNING: 1. It is a electric set. Please never put it in the moist place to avoid from water entering. 2. Please observe the instructions on the manual strictly to operate or install this set. 3. If because of your wrong operation processes, it causes damage to the transmitter or injures yourself and somebody else, our company will not take responsibility for any loss on these problems. 4. Never mix the used and new battery up for use. 5. Never recharge the uncharged battery. GUARANTY OF THE PRODUCTS Our products have been examined strictly. If not the contrived factors for product’s damaged, please contact our company or sellers. It is important that any users must be responsible for any loss and injuries because of your wrong operations. For a novice, if you want to ask some helps with installation or test or our product, please contact the sellers. We will work for your warmly and sincerely. Congratulation! After you finish above installation and test process, the model had been set up already and you could enjoy your model. Besides we will improve and update our products (SMARTECH serial, products) 4 continusly, we only need ask for the new information and new product’s contents. We hope our best products of radio controller can make a lot of enjoyment in your life. FCC STATEMENT: “Modifications not authorized by the manufacturer may void users authority to operate this device” NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help.

Block Diagram

Transmitter Block Diagram 2 ChanneldirectiontransitionSport statuscontrol Coding plastic Power supplychecking indicationSignal processor RangeModulation PowerAmplifier Signal Transmit 12V Power supply Power supply transact

External Photos

PHOTOGRAPH OF THE PRODUCT FRONT VIEW OF THE PRODUCT REAR VIEW OF THE PRODUCT

Operational Description

Circuit Description Model: 30113 The 27MHz crystal oscillator drives the base of Q4 the high frequency amplifier. The modulated frequency provided by IC U1(EM78P458) . The output of Q3 has the matching network consisting of C28,C25,C26,C27,C29,T2,T3 and L4 that limit the harmonic content and effect the proper coupling of the antenna to the output stage. Antenna, Ground and Power Source The antenna consists of a 82.6cm long telescoping chrome over brass tubing. There is no external ground connection. The ground is only that of the printed circuit board. Electric current is supplied by a 8X1.5V(“2A” ) primary battery .

Schematics

1 2 3 4 5 6 78 ABCD 8 7 6 5 4 3 2 1 D CBA Titl e Nu mbe r R ev i sio n Size A3 Date: 1-Jun-2004 Sheet of File: D:\ Chi u-A\Perfect\ Perfect-Sch \3 01 1 3 -TX-C.d d b Drawn By: -Vi n 3 GND 2 +Vout 1 U2LM7 8L0 5 X12TT 3.58MT Q4C9018 C13104pF50V + C2 0220uF16V D11N4001 1 2 5 3 4 T3T12 0 VR L42.2uH ANT C2930pF50V 1 2 5 3 4 T2T12 0 VR C2568pF50V C2768pF50V C2668pF50V L33.9uH Q3C2314 R181.2K C2882pF50V R212.2R C11103pF50V R2 0330R C7103pF50V 12 534 T1TA92 VR C2468pF50V C2133pF50V C2 34pF50V C2233pF50V C6103pF50V R1 622R R19270R C10103pF50V R124.7K X227.???Mzh P56 /CI N+ 1 P57/ CO 2 P54/ TCC 19 P60/ ADC1 3 P62/ADC3 6 P63/ ADC4 7 P51/ PWM1 13 P50/ INT 12 P67/ ADC8 11 P66/ ADC7 10 OSC 2 18 OSC 1 17 VDD 16 RES 15 P55 /CI N+ 20 P61/ ADC2 4 VSS 5 P64/ ADC5 8 P65/ ADC6 9 P51/ PWM2 14 U1EM7 8P4 58 R11.5K C1 6102pF50V C15102pF50V Q1C945 C1 7102pF50V R93.2K R1 533K Q2A7 33 R72.2K R222.2R R62.2K R85.1K R21.5K R31.5K + C18100uF16V C3103pF50VC12104pF50V D21N5819 R510K R410K C4103pF50V 2 31 SW3POWER SW 1234 J2POWER JACK C2103pF50V C1103pF50V 2 31 SW1 RF SW 2 31 SW2 RF SW R146.8K 123456 J1VR J ACK C1 4104pF50V C3047pF50V R103.9K L24.7uH R1 710R LED3LED3 REDLED2LED2 YOLLED1LED1 GRE C9103pF50V C8103pF50V VI NBAT TGNDGND R134.7K C3 1120pF50V R1 115R C5103pF50V L14.7uH + C19100uF16V C32103pF50V

Test Report

香港標準及檢定中心 Hong Kong Standards and Testing Centre Date : 2004-06-10 TEST REPORT Page 1 of 1 No. : HM151222 This report shall not be reproduced unless with prior written approval from the Hong Kong Standards and Testing Centre. 香港新界大埔工業村大宏街10號 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] For full text of “Conditions of Issuance of Test Report”, please refer to overleaf or refer to the website of STC: www.hkstc.org (the section “Application and Quotation”). Applicant: Perfect Toys International Co., Ltd Description of Samples: Model name: Sport-3 Model no.: 30113 Brand name: Smartech FCC ID: JHP30113-TX Date Samples Received: 2003-10-11 Date Tested: 2004-05-28 Investigation Requested: FCC Part 15 Subpart C Conclusions: The submitted product COMPLIED with the requirements of Federal Communications Commission [FCC] Rules and Regulations Part 15. The tests were performed in accordance with the standards described above and on Section 2.2 in this Test Report. Remarks: ---- K C Lee, EMC for Chief Executive 香港標準及檢定中心 Hong Kong Standards and Testing Centre Date : 2004-06-10 TEST REPORT Page 2 of 2 No. : HM151222 香港新界大埔工業村大宏街10號 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] For full text of “Conditions of Issuance of Test Report”, please refer to overleaf or refer to the website of STC: www.hkstc.org (the section “Application and Quotation”). CONTENT: Cover Page 1 of 31 Content Page 2-3 of 31 1.0 General Details 1.1 Test Laboratory Page 4 of 31 1.2 Applicant Details Page 4 of 31 Applicant HKSTC Code Number for Applicant Manufacturer 1.3 Equipment Under Test [EUT] Page 5 of 31 Description of EUT operation 1.4 Date of Order Page 5 of 31 1.5 Submitted Samples Page 5 of 31 1.6 Test Duration Page 5 of 31 1.7 Country of Origin Page 5 of 31 1.8 Additional Information of EUT Page 6 of 31 2.0 Technical Details 2.1 Investigations Requested Page 7 of 31 2.2 Test Standards and Results Summary Page 7 of 31 3.0 Test Results 3.1 Emission Page 8-15 of 31 3.2 Bandwidth Measurement Page 16-19 of 31 香港標準及檢定中心 Hong Kong Standards and Testing Centre Date : 2004-06-10 TEST REPORT Page 3 of 3 No. : HM151222 香港新界大埔工業村大宏街10號 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] For full text of “Conditions of Issuance of Test Report”, please refer to overleaf or refer to the website of STC: www.hkstc.org (the section “Application and Quotation”). Appendix A List of Measurement Equipment Page 20 of 31 Appendix B Duty Cycle Correction During 100 msec Page 21-29 of 31 Appendix C Photographs Page 30-31 of 31 香港標準及檢定中心 Hong Kong Standards and Testing Centre Date : 2004-06-10 TEST REPORT Page 4 of 4 No. : HM151222 香港新界大埔工業村大宏街10號 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] For full text of “Conditions of Issuance of Test Report”, please refer to overleaf or refer to the website of STC: www.hkstc.org (the section “Application and Quotation”). 1.0 General Details 1.1 Test Laboratory The Hong Kong Standards and Testing Centre Ltd. EMC Laboratory 10 Dai Wang Street, Taipo Industrial Estate New Territories, Hong Kong Telephone: 852 2666 1888 Fax: 852 2664 4353 1.2 Applicant Details Applicant Perfect Toys International Co., Ltd. 2/F., Block 3, Wah Lai Industrial Centre, 10-14 Kwei Tei Street, Fo Tan, Shatin, New Territireies, Hong Kong HKSTC Code Number for Applicant PET004 Manufacturer Dong Guan Xian Hao Electric Appliances & Toys Co., Ltd. Tian Xin Mangement Zone, Huang Jiang Town, Dong Guan, Guang Dong, China 香港標準及檢定中心 Hong Kong Standards and Testing Centre Date : 2004-06-10 TEST REPORT Page 5 of 5 No. : HM151222 香港新界大埔工業村大宏街10號 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] For full text of “Conditions of Issuance of Test Report”, please refer to overleaf or refer to the website of STC: www.hkstc.org (the section “Application and Quotation”). 1.3 Equipment Under Test [EUT] Description of Sample Model Name: Sport-3 Manufacturer: Dong Guan Xian Hao Electric Appliances & Toys Co., Ltd Brand Name: Smartech Model Number: 30113 Input Voltage: 12Vd.c (“AA” size battery x 8) 1.3.1 Description of EUT Operation The Equipment Under Test (EUT) is a Perfect Toys International Co., Ltd., Sport-3 . The transmitter is a 2 button transmitter. The EUT continues to transmit while button is being pressed, Modulation by IC. and type is pulse modulation. 1.4 Date of Order 2003-10-11 1.5 Submitted Sample(s): 10 Samples 1.6 Test Duration 2004-05-28 1.7 Country of Origin China 香港標準及檢定中心 Hong Kong Standards and Testing Centre Date : 2004-06-10 TEST REPORT Page 6 of 6 No. : HM151222 香港新界大埔工業村大宏街10號 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] For full text of “Conditions of Issuance of Test Report”, please refer to overleaf or refer to the website of STC: www.hkstc.org (the section “Application and Quotation”). 1.8 Additional Information of EUT Submitted Not Available User Manual Part List Circuit Diagram Printed Circuit Board [PCB] Layout Block diagram FCC ID Label 香港標準及檢定中心 Hong Kong Standards and Testing Centre Date : 2004-06-10 TEST REPORT Page 7 of 7 No. : HM151222 香港新界大埔工業村大宏街10號 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] For full text of “Conditions of Issuance of Test Report”, please refer to overleaf or refer to the website of STC: www.hkstc.org (the section “Application and…

Text truncated - open the document above for the full version.

Test Setup Photos

TEST SET UP PHOTOGRAPH OF THE PRODUCT MEASUREMENT OF RADIATED EMISSION TEST SET UP