K3MSJ70B

K3MSJ70B USER MANUAL This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions : (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION : Any changes or modification in construction of this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Introduction... Congratulations on your purchase of the K3MSJ70B. You will find your new automotive security system / Remote Starter has "user friendly", integrated features, which will enhance it usefulness, and prove to be very reliable for many years. The State-of-the-Art features included with the K3MSJ70B have been achieved through numerous technological advances and many hours of interactive field evaluations from installation professionals. In order to maximize your protection capabilities, we highly suggest that you take a few minutes to read the "User Manual" . This manual will provide details on how to efficiently operate the K3MSJ70B. If you have any questions on the operation of your K3M security system, please don't hesitate to ask your K3M dealer for more explicit details on the operation of the system in your particular vehicle. K3M SECURITY is a customer service oriented company. If for some reason you are not satisfied with the performance of one of our products, please feel free to write us a note about your experiences. Efficient automotive security products are a result of reactions and suggestions from you....our valued customers. FEATURES YOUR FEATURES INCLUDE Trunk Release (Option) The K3MSJ70B offers you Electric Trunk Release by Remote Control. This is really helpful if you have a arm full of bags and you need to open the trunk. No fumbling for your keys... just depress button #2 on the Remote Transmitter and you trunk will be electronically released. Starter Disable Starter Disable disconnects the starter control wire leading from the Ignition Switch to your Starter Motor, preventing unauthorized starting of your vehicle. The Starter Disabling system is your first line of defense against auto theft. Dual Parking Light Flash If your car in a parking lot with 100 other vehicles, Parking Light Flash makes identification of your vehicle easy when your security system is triggered by a potential thief, or with the Remote Car Finder Feature. Our Parking Light Flash system has been designed to work with ALL vehicles. Dome Light Monitor Originally designed to add security while returning to your vehicle. The K3MSJ70B has the capability to turn on your interior light so you can see inside the vehicle. The interior lights are automatically extinguished after 30 seconds. or when the vehicle’s ignition is turned on. Each time you disarm your K3MSJ70B. The interior lights will come on for 30 seconds...or until the Ignition is turned on. Features, Page 1 Remote Door Lock / Unlock Remote Control Door Lock operates automatically as you use your Remote Transmitter to "Arm" and "Dis-Arm" your K3MSJ70B. When you "Arm" your system, the doors will automatically lock. And when you "Dis- Arm" your K3MSJ70B , the doors will automatically unlock. Ignition Controlled Door Locks Ignition Controlled Door Locks offer a unique safety feature for any car. It has been a proven fact that locked doors have less tendency to fly open in automobile accidents. A great feature to lock the kids doors! When the vehicle's ignition key is turned "On", the doors will automatically LOCK. When the ignition key is turned "Off", the doors will then automatically UNLOCK. Three Channel Transmitter The K3MSJ70B 3-Channel Transmitter offers you the customer the ability to operate several OPTIONAL functions with a single Remote Transmitter. You can: (Arm and Disarm your security system) (Turn off your "chirp" sounds) (Remotely Start your car) (Open your trunk) Two Stage Shock Sensor The Two Stage Shock Sensing system adds extra security to your vehicle's security system by offering a "Warn-Away" type shock system, that warns off the would be thief, by sounding the siren rapidly for a short duration, when the vehicle is being tampered with. Features, Page 2 Code Learning Receiver With Code Learning, you will be able to easily add a new transmitter to your system in the event you were to loose or break a transmitter. In the past, you had to pay an installer to code a new transmitter to your system. Anti- HiJacking The K3M Anti-HiJacking system can be initiated by YOU...the vehicle owner. Some people like this system, some don’t. Now you can choose whether or not to use the Anti-HiJacking feature. When entering a suspicious area, simply depress Transmitter button #3. This will place the Anti-HiJacking feature in “Standby” mode. In “Standby” mode, if the Ignition Switch is in the “On” position, and the door is opened (Like a CarJacking), the processor will begin timing. In 40 seconds...the siren will sound...and the lights will flash. Once the thief turns “Off” the vehicle...it can’t be re-started! In fact...your remote controls will no longer operate! The thief is stuck with a wailing siren, and flashing parking lights. (To reset..turn on your Ignition, then turn “On” the Valet Switch) CAR FINDER MODE The K3MSJ70B has a unique “Car Finder” feature. This feature can help assist you in locating your vehicle in a crowded parking lot. Simply depress button #3...and hold it until the siren begins “Chirping” rapidly. This will make your vehicle easy to find. Features, Page 3 IDENTIFY THE COMPONENTS THREE BUTTON REMOTE TRANSMITTERS Your K3MSJ70B Security System was shipped with two transmitters. The THREE BUTTON REMOTE TRANSMITTERS send commands to the Electronic Control Unit (ECU). Transmitters have unique codes, so that your transmitters won’t operate your neighbor’s security system. Extra transmitters can be purchased and the ECU can be…

Text truncated - open the document above for the full version.

K3MSJ70B BLOCK DIAGRAM OF BASE UNIT D2 LED INDICATOR D1 RF POWER SWITCHINGQ1 ASK MODE OSCILATOR(ALTERNATIVE COLPITTS TYPE)Q2,C2~5,L2 RODANTENNA R2 S 3S1S2BATTERY VCCDATA OUT OSC 1 DATA1DATA2VSSOSC 2 ENCODER IC U1 R3 C6,C7 FILTER

EXTERNAL TOP SIDE EXTERNAL BOTTOM SIDE FCC ID : K3MSJ70B

PROPOSED FCC ID. LABEL AND MARKING BOTTOM SIDE

INTERNAL TOP SIDE INTERNAL BOTTOM SIDE FCC ID : K3MSJ70B FCC ID : K3MSJ70B

CIRCUIT DESCRIPTION OF THE TRANSMITTER ! There are three buttons (SW-1,SW-2 & SW-3) on the face of the transmitter that commands the SecuritySystem operated as follows: BUTTON #1 (SW-1) = Arms and Disarms BUTTON #2 (SW-2) = Opens the trunk / or silently “Arms” and “Disarms” BUTTONS #3 (SW-3) = Commands a Channel (3) Signal. This signal is generally used to command a Remote Starter Module, but can beused to operate any vehicle function. ! Depress Button (Switch) on Remote Transmitter. Power is supplied to the ASK MOD. oscillation circuit and Encoder IC U1. ! Then, the Encoder IC U1 is activated. ! The Encoder IC U1 is a 2 24 series of encoder C-MOS LSIs designed for use in remote control systems. ! A transmission word of the Encoder is transmitted to the DATA OUT pin and R2 consecutively, after atrigger is received. The trigger signal occurs on the DATA 1-DATA 2 pin.! This transmission word (binary) is applied to the base of TR Q2 of LC type ASK MOD. oscillation circuit. ! The RF oscillation circuit consists of Alternated Collpitts type (Q2,C2~5,CV1,L2 Inductor) which operatesthe 300Mhz frequency band. The Modulator Signal is transmited to Rod Antenna via filter C6-C7. The Frequency of 300Mhz is finely adjusted by trimmer capacitor C2.

K3MSJ70B BLOCK DIAGRAM OF BASE UNIT D2 LED INDICATOR D1 RF POWER SWITCHINGQ1 ASK MODE OSCILATOR(ALTERNATIVE COLPITTS TYPE)Q2,C2~5,L2 RODANTENNA R2 S 3S1S2BATTERY VCCDATA OUT OSC 1 DATA1DATA2VSSOSC 2 ENCODER IC U1 R3 C6,C7 FILTER {Doc} {RevCode} k3msj70b A 11 Thursday, April 29, 1999 TitleSize Document Number Rev Date: Sheet of U1HT6P20 D1 1 D2 2 VSS 3 OSC1 5 OSC2 4 DATA/OUT 6 VCC 7 NC 8 Q1KTC3875 1 2 3 Q2SC3356/R23 1 2 3 D2KDS184 2 3 1 S3KTP1107 1 2 S1KTP1107 1 2 S2KTP1107 1 2 R1330R 12 R2560K 12 C1103 12 C41.5pF 1 2 C36pF 12 C63pF 1 2 L11.5uH 1 2 D1SLR103 12 R32M 1 2 L22*1/2 12 C74pF 12 C58pF 12 C23pF 12 BT1BATTERY TERMINAL 12 R447R 12 ANTROD ANTENNA 1

KTL Korea Testing Laboratory Page 1 of 15 TEST REPORT This test report only responds to the tested sample and shall not be reproduced except in full without written approval of the the Korea Testing Laboratory. Tested and reported by Reviewed by Soun-Kweon Seol , Senior Engineer Seok-Jin Kim , EMC Team Leader KOREA TESTING LABORATORY FG101-01-02-00 222-13, Guro-Dong Guro-Gu Seoul Korea 152-053 ht tp://www.ktl.re.kr Ref. Report No. 99-341-023 Name and address of the applicant Sam Joo Electronic Co. 366-7 Songnae-Dong, Sosa-Ku, Buchun-City, Kyungki-Do, Korea 422-040 Standard / Test regulation FCC Part 15, Subpart C Test result Pass Incoming date : April 20, 1999 Test item(s) ; Security/Remote Control Transmitter (Car Alarm) Model/type ref. ; SJ70B Manufacturer ; Sam Joo Electronic Co. Additional information ; -Required Authorization :Certification -FCC ID. : K3MSJ70B Test date : May 19, 1999 Issue date : May 27, 1999 Ref. Report No. 99 - 341 - 023 Page 2 of 15 TABLE OF CONTENTS . GENERAL INFORMATION ................................................................................................................... 3 1. Grantee Name and Mailing Address 2. Manufacturer's Name and Mailing Address 3. Equipment Descriptions 4. Rules and Regulations 5. Measuring Procedure 6. Place of Measurement 7. Date of Measurement . GENERAL REQUIREMENTS OF THE EUT ...................................................................................... 5 1. Labelling Requirement (Section 15.19) 2. Information to User (Sections 15.21) 3. Special Accessories (Section 15.27) 4. Compliant Conditions (Section 15.231) 5. Modification of the Equipment Under Test . INPUT POWER MEASUREMENT (Section 15.31)............................................................................. 6 . RADIATED EMISSION MEASUREMENT (Section 15.231)............................................................ 7-13 1. Test Procedure 2. Photograph for the worst case configuration 3. Sample Calculation 4. Measurement Data 5. Reference Data . OCCUPIED BANDWIDTH MEASUREMENT (Section.15.231)...................................................... 14 . TEST EQUIPMENTS USED FOR FCC COMPLIANCE TESTING................................................ 15 Ref. Report No. 99 - 341 – 023 Page 3 of 15  . GENERAL INFORMATION 1. Grantee Name and : Sam Joo Electronic Co. Mailing Address 366-7 Songnae-Dong, Sosa-Ku, Buchun-City, Kyungki-Do, Korea 422-040 2. Manufacturer's Name and : Sam Joo Electronic Co. Mailing Address 366-7 Songnae-Dong, Sosa-Ku, Buchun-City, Kyungki-Do, Korea 422-040 3. Equipment Descriptions 3.1 Operating Frequency : 300.0MHz 3.2 Type of Emission : Pulse Code Signal 3.3 Power Supply : DC 6.0V (Battery) 3.4 Additional Information; - Oscillator used : 300.0MHz LC oscillator - I.C. used : HT6P20(HOLTEK) 4. Rules and Regulations : FCC Part 15, Subpart C 5. Measuring Procedure : ANSI C63.4-1992 6. Place of Measurement : Absorber-lined room(3-Meter) of KAITECH 7. Date of Measurement 6.1 Conducted Emission : Not Applicable 6.2 Radiated Emission : May 19, 1999 Ref. Report No. 99 - 341 - 023 Page 4 of 15  . GENERAL REQUIREMENTS OF THE EUT 1. Labelling Requirement (Section 15.19) 1.1 Location on Enclosure : Manual for Installation and Operating Instruction 1.2 How Applied : Printing 2. Information to User (Section 15.21) The following or similar statements were provided in the manual for user instruction. Please refer page 2 of the attached manual for details. 3. Special Accessories (Section 15.27) 3.1 Were the special Accessories provided? [ ] yes, [ x ] no 3.2 If yes, details for the special accessories are as follows : 3.3 If yes, were the appropriate instructions provided on the first page of the text concerned with the device? [ ] yes, [ ] no 3.4 Are these accessories provided of the type which can be readily obtained from multiple retail outlets? [ ] yes, [ ] no And therefore does the manual specify what additional components or accessories are required to used in order to comply with the Rules? [ ] yes, [ ] no This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION : Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Ref. Report No. 99 - 341 – 023 Page 5 of 15 4. Compliant Conditions (Section 15.231) 4.1 Was the EUT used for continuous transmissions, such as voice or video, and data transmission ? [ ] yes, [ x ] no 4.2 Was the EUT manually operated ? [ x ] yes, [ ] no If yes, did the EUT employ a switch that would automatically deactivate the transmitter within not more than 5 seconds of being released ? [ x ] yes, [ ] no 4.3 Was the EUT automatically activated ? [ ] yes, [ x ] no If yes, did the EUT cease transmission within 5 seconds after deactivation ? [ ] yes, [ ] no 4.4 Was the EUT used for periodic transmissions at regular predetermined intervals ? [ ] yes, [ x ] no 5. Modification of the Equipment Under Test [ x ] Any modifications were not made to the EUT during the testing since the test results were found of be complied with the FCC Rules with the EUT in the as received condition. [ ] Modification(s) was(were) made to the EUT in order to make it meet FCC Rules since it had shown non- compliance for some test items in the course of our testing. - Status of non-compliance : - Details of Modifications : Ref. Report No. 99 - 341 - 023 Page 6 of 15  . INPUT POWER MEASUREMENT (Section 15.31) INPUT POWER 31.02 mW Note : 1. Input Power : P ove = (P p x D) pulse + P D Where, P p : Input Peak Power (= V x I p ) P D : Input DC Power (= V x I D ) D : Duty Cycle (= τ eff x PRF) Measured Input Voltage (V) = 6.22 DCV Measured Input Peak Current (I p ) = 4.27 mA Measured Input …

Text truncated - open the document above for the full version.

TEST SETUP PHOTOS RADIATED EMISSION