KE3-3001186BOUNDARY PLUS TRANSMITTER

Boundary Plus ® Transmitter Owner’s Manual www.invisiblefence.com 2 www.invisiblefence.com Important Precautions • Invisible Fence ® Brand pet containment systems have contained over two million pets. However, there are some precautions you should take. • Read and retain manuals: Read the entire Owner’s Manual before using your new Invisible Fence ® Brand pet containment system. • Adhere to all warnings and cautions contained in any Invisible Fence ® Brand manual. WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury. CAUTION used without the safety alert symbol, indicates a hazardous situation which, if not avoided, could result in harm to your pet. NOTICE is used to address safe use practices not related to personal injury. • Replacing the battery backup with a battery not specifically approved by Invisible Fence ® Brand may cause fire or explosion. Refer all service to your Invisible Fence ® Brand Dealer only. • Not every pet can be trained to avoid the established boundary. Sometimes even a properly trained pet may cross the boundary. Therefore, Invisible Fence ® , Inc., as well as Invisible Fence ® Distributors and Dealers, cannot guarantee the system will, in all cases, keep a customer’s pet within the established boundary. Accordingly, if a customer has reason to believe that their pet may pose a danger to others, or harm itself, the customer should not rely solely upon the Invisible Fence ® Brand pet containment system to keep the pet from crossing the boundary. • Do not install, connect, or remove your system during a lightning storm. If the storm is close enough for you to hear thunder, it is close enough to create hazardous surges. • Read and follow the important instructions on how to avoid pressure necrosis in your Invisible Fence ® Brand Computer Collar ® manual. • Train your pet according to the instructions in the Invisible Fence ® Brand training manuals. Complete all steps before allowing your pet to run free. Do not become overly confident if your pet has become conditioned to the Invisible Fence ® Brand pet containment system sooner than expected. • Your Invisible Fence ® Brand Dealer has professionally installed your pet containment system and ensured it is working properly. You will want to perform periodic maintenance checks to make sure the system is properly functioning for your pet’s safe containment. • Check the Invisible Fence ® Brand transmitter periodically to make sure it is operating properly. To do this, simply bring the Computer Collar ® to the edge of the containment field to verify function. • The transmitter has visual and audible signals to warn of a system malfunction. The transmitter should be installed where such signals may be easily seen and heard. If the transmitter is installed by the customer in an enclosed box, or in a place not readily accessible to the customer, the customer will not benefit from the system’s warning functions, for which Invisible Fence, Inc., as well as Invisible Fence Distributors and Dealers, assume no responsibility. • Do not attempt to service any Invisible Fence ® Brand equipment. Refer all service to your authorized Invisible Fence ® Brand Dealer. Only your authorized Invisible Fence ® Brand Dealer should make adjustments to your pet containment system. • All Invisible Fence ® Brand pet containment systems are designed for domesticated animal use only. Never attempt to use this product for any purpose not specifically described in this manual. • Use care when mowing, aerating, or trimming your lawn so as not to cut the loop wire. • If you have any questions about any aspect of your Invisible Fence ® Brand pet containment system, call your Invisible Fence ® Brand Dealer immediately. WARNING CAUTION NOTICE WARNING CAUTION NOTICE www.invisiblefence.com 3 Congratulations on your purchase of the world’s premier pet containment solution, the Invisible Fence ® Brand. When professionally installed, the Invisible Fence ® Brand pet containment system is backed with a one-year, money-back performance guarantee. The support of your Invisible Fence ® Brand Dealer gives you peace of mind that your pet remains Safe At Home ® . Refer to the back of your sales contract for complete details. __________________________________________________ Table of Contents Components .................................................................................................................................................4 How the Systems Works .................................................................................................................................4 Transmitter Status Indicators .........................................................................................................................5 Periodic Maintenance Check .........................................................................................................................6 Troubleshooting Guide ..................................................................................................................................6 Battery Disposal ............................................................................................................................................7 Compliance ..................................................................................................................................................8 __________________________________________________ 4 www.invisiblefence.com Components Transmitter Boundary Plus ® AC Adapter Owner’s Manual How the System Works The Boundary Plus ® Transmitter is designed to work with an Invisible Fence ® Brand Computer Collar ® to contain your pet within areas you choose, or teach your pet to avoid specific areas such as flower beds, gardens, or pools. The transmitter produces a signal that travels along the signal field wire and back to the transmitter to produce an Invisible Boundary ® barrier. When your pet approaches the establ…

Text truncated - open the document above for the full version.

COVER LETTER IC: 2721A-3001186 Radio Systems Corporation We, Radio Systems Corporation, for this Application (IC: 2721A-3001186),hereby acknowledges that this product cannot be distributing, leased, or offered for sale in Canada until it is listed on the Industry Canada Radio Equipment List, the power of sale belong to the Radio Systems Corporation or the company which Radio Systems Corporation authorized. The Boundary Plus® Transmitter is designed to work with an Invisible Fence® Brand Computer Collar® to contain your pet within areas you choose, or teach your pet to avoid specific areas such as flower beds, gardens, or pools. The transmitter produces a signal that travels along the signal field wire and back to the transmitter to produce an Invisible Boundary® barrier. September 21, 2011 Radio Systems Corporation Clifton P. Brick

Radio Systems Corp Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: KE3-3001186. Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Exhibit Type File Name Schematics Block Diagram Operational Description KE3-3001186_SCH.pdf KE3-3001186_BlockDiagram.pdf KE3-3001186_CircuitDescription.pdf The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Clifton P. Brick

Radio Systems Corporation FCC ID: KE3-3001186 POWER OF ATTORNEY September 21, 2011 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern: We, the undersigned, hereby authorize Waltek Services (ShenZhen) Co., Ltd. (Philo Zhong) on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Waltek Services (ShenZhen) Co., Ltd. (Philo Zhong) on our behalf shall have the same effect as acts of our own. This authorization expires on September 20, 2012. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. We, Radio Systems Corporation, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely, Radio Systems Corporation ------------------ Clifton P. Brick

2.1 Product View 2.2 EUT – Appearance View

Page:22 of 22 Radio Systems Corporation FCC ID: KE3-3001186 WALTEK SERVICES Reference No.: WT11084242-D-E-F 9 FCC Label This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1)this device may not cause harmful interference,and (2) this device must accept any interference received, including interference that may cause undesired operation The Label must not be a stick-on paper. The Label on these products must be permanently affixed to the product and readily visible at the time of purchase and must last the expected lifetime of the equipment not be readily detachable.

FCC ID Label Sample for Model: RIG00-11334

2.1 EUT – Open View 2.2 PCB – Front View 2.3 PCB – Back View

Page: 1 of 22 FCC TEST REPORT WALTEK SERVICES Reference No.: WT11084242-D-E-F FCC ID : KE3-3001186 Applicant : Radio Systems Corporation Address : 10427 Electric Ave. Knoxville, TN 37932, USA Equipment Under Test (EUT) : Product Name : Boundary Plus® Transmitter Model No. : RIG00-11334 Standards : FCC CFR47 Part 15 Section 15.209:2009 Date of Test : August 22 ~ August 26 Date of Issue : September 5, 2011 Test Engineer : Hunk yan Reviewed By : Philo zhong Test Result : PASS Prepared By: Waltek Services (Shenzhen) Co., Ltd. 1/F, Fukangtai Building, West Baima Rd., Songgang Street, Baoan District, Shenzhen 518105, China Tel :+86-755-27553488 Fax:+86-755-27553868 — The sample detailed above has been tested to the requirements of Council Directives ANSI C63.4:2003. The test results have been reviewed against the Directives above and found to meet their essential requirements. Page:2 of 22 Radio Systems Corporation FCC ID: KE3-3001186 WALTEK SERVICES Reference No.: WT11084242-D-E-F 2 Test Summary Test Items Test Requirement Test Method Result Radiated Emissions (9kHz ~ 1GHz) Part 15.209 ANSI C63.4: 2003 PASS Conducted Emissions (150kHz ~ 30MHz) Part 15.207 ANSI C63.4:2003 PASS Page:3 of 22 Radio Systems Corporation FCC ID: KE3-3001186 WALTEK SERVICES Reference No.: WT11084242-D-E-F 3 Contents Page 1 COVER PAGE........................................................................................................................................................ 1 2 TEST SUMMARY .................................................................................................................................................. 2 3 CONTENTS............................................................................................................................................................. 3 4 GENERAL INFORMATION ................................................................................................................................ 4 4.1 CLIENT INFORMATION........................................................................................................................................... 4 4.2 GENERAL DESCRIPTION OF E.U.T. ........................................................................................................................ 4 4.3 DETAILS OF E.U.T................................................................................................................................................. 4 4.4 DESCRIPTION OF SUPPORT UNITS.......................................................................................................................... 4 4.5 STANDARDS APPLICABLE FOR TESTING................................................................................................................ 4 4.6 TEST FACILITY...................................................................................................................................................... 5 4.7 TEST LOCATION.................................................................................................................................................... 5 5 EQUIPMENT USED DURING TEST .................................................................................................................. 6 6 CONDUCTED EMISSIONS.................................................................................................................................. 7 6.1 E.U.T. OPERATION................................................................................................................................................ 7 6.2 EUT SETUP........................................................................................................................................................... 8 6.3 CONDUCTED EMISSION TEST RESULT................................................................................................................... 9 6.4 PHOTOGRAPH – RADIATION EMISSION TEST SETUP............................................................................................ 11 7 RADIATED EMISSIONS .................................................................................................................................... 12 7.1 MEASUREMENT UNCERTAINTY........................................................................................................................... 13 7.2 EUT SETUP......................................................................................................................................................... 13 7.3 SPECTRUM ANALYZER SETUP............................................................................................................................. 14 7.4 TEST PROCEDURE................................................................................................................................................ 14 7.5 SUMMARY OF TEST RESULTS.............................................................................................................................. 15 7.6 PHOTOGRAPH – RADIATION EMISSION TEST SETUP............................................................................................ 17 8 PHOTOGRAPHS - CONSTRUCTIONAL DETAILS...................................................................................... 18 8.1 PRODUCT VIEW................................................................................................................................................... 18 8.2 EUT – APPEARANCE VIEW................................................................................................................................. 18 8.3 EUT – OPEN VIEW.............................................................................................................................................. 19 8.4 PCB – FRONT VIEW............................................................................................................................................ 20 8.5 PCB – BACK VIEW...............................................................…

Text truncated - open the document above for the full version.

2.1 Photograph – Radiation Emission Test Setup 2.2 Photograph – Radiation Emission Test Setup Below 30MHz Above 30MHz