KE3-3002539SMART PET ACCESS DOOR

PASSport Pet Access Smart System ™ Installation and Operating Guide Please read this entire guide before installation. Model Numbers: PPA00-13795 and PPA00-13796 2 Customer Care Center 1-800-732-2677 Important Safety Information Explanation of Attention Words and Symbols used in this guide This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury. CAUTION, used with the safety alert symbol, indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. CAUTION, used without the safety alert symbol, indicates a hazardous situation which, if not avoided could result in harm to your pet. NOTICE is used to address practices not related to personal injury. • When children are present in the home, it is important to consider the pet door during child proofing activities. The pet door may be misused by a child resulting in the child accessing potential hazards that may be on the other side of the pet door. Purchasers/ Homeowners with swimming pools should ensure that the pet door is monitored at all times and that the swimming pool has adequate barriers to entry. If a new hazard is created inside or outside of your home, which may be accessed through the pet door, Radio Systems ® Corporation recommends that you properly guard access to the hazard or remove the pet door. The closing panel or lock, if applicable, is provided for aesthetic and energy efficiency purposes and is not intended as a security device. Radio Systems ® Corporation will not be liable for unintended use, and the purchaser of this product accepts full responsibility for oversight of the opening it creates. • Power Tools. Risk of severe injury; follow all safety instructions for your power tools. Be sure to always wear your safety goggles and other proper safety equipment. • The user, prior to installation, must become familiar with all building codes that may affect the installation of the pet door and determine, along with a licensed contractor, its suitability in a given installation. This pet door is not a fire door. It is important for the owner and contractor to consider any risks that may be present inside or outside of the pet door, any risks that may be created by subsequent changes to your property and, how they may relate to the existence and use, including misuse of the pet door. • If cutting metal surface, be aware of sharp edges to prevent injury. • During pet training while pet door is in Open Mode, make sure to GENTLY lower flap onto pet’s back. Also avoid possible injury by making sure your pet is entirely through the pet door opening, including paws and tail, before completely releasing flap. www.petsafe.net 3 • Read this entire guide prior to cutting or modifying an opening in your door or wall. Do not proceed with cut-out or installation until your PASSport ™ is assembled, powered up, programmed for your pet and all steps under “Prepare, Test and Setup” have been completed. • Keep these instructions with important papers; be sure to transfer these instructions to the new owner of the property. • Unauthorized changes or modifications may void the user’s authority to operate this equipment, and void the warranty. • Read this entire guide prior to cutting or modifying an opening in your door or wall. Do not proceed with cut-out or installation until your PASSport ™ is assembled, powered up, programmed for your pet and all steps under “Prepare and Test PASSport ™ ” have been completed. • We do not accept any responsibility for openings that are cut or modified in doors or walls or any damage caused to doors or walls in forming or modification of such openings, including any costs associated with the repair or replacement. • If operating from the optional Rechargeale Lithium battery, the battery and bat- tery compartment coannot be exposed to temperatures below 32°F (0°C). • If homeowner’s door or other application is not level, the pet door must be marked level to swing properly. • When applying the cutting template, there should be a minimum of 3” between the bottom and sides of the door and the outer edge of the template to maintain the structural integrity of the door. • Make sure there is nothing underneath the door where you will be drilling holes or cutting out the opening. • Use a manual screwdriver to tighten screws. Do not over-tighten. Over-tightening can strip the screws or warp the pet door frame. 4 Customer Care Center 1-800-732-2677 Thank you for choosing the PetSafe ® brand. You and your pet deserve a companionship that includes memorable moments and a shared understanding together. Our products and training tools promote a lifestyle of protection, teaching, and love—essentials that influence memories for a lifetime. If you have any questions about our products or training your pet, please visit our website at www.petsafe.net or contact our Customer Care Center. PRODUCT WARRANTY To get the most protection out of your warranty, please register your product within 30 days at www.petsafe.net. By registering and keeping your receipt, you will enjoy the product’s full warranty, and should you ever need to call the Customer Care Center, we will be able to help you faster. Most importantly, PetSafe ® will never give or sell your valuable information to anyone. Complete warranty information is available online at www.petsafe.net. Table of Contents GETTING STARTED Components ..............................................................................................................................................................................................................# How the PASSport ™ Pet Access Smart System Works ...............................................................................................................................…

Text truncated - open the document above for the full version.

10427 PetSafe Way Knoxville, TN. 37932 865-777-5404 www.petsafe.net 4/17/2013 RE: KE3-3002539 2721A-3002539 To whom it may concern: This is to attest that Radio Systems Corporation will be responsible to make sure the following changes made to the EUT, part number 300-2539, will be applied to all manufactured or marketed products. These are the changes: 1) L4 was added between the AC adapter input and the boost converter circuitry input. 2) C43 was added right at the AC adapter power input to the main PCBA. 3) L5 was added between the RFID coil driver integrated circuit (U9) and the RFID coil resonant circuit. 4) C47 was added between the output side of L5 and ground for the RFID power circuitry. Sincerely, Cindy Allen Product Safety and Regulatory Specialist Radio Systems Corporation 10427 PetSafe Way Knoxville, TN 37932 (p) 865-824-5431 www.petsafe.net

10427 PetSafe Way Knoxville, TN. 37932 865-777-5404 www.petsafe.net AGENCY AGREEMENT Federal Communications Commission Date: 9/18/2012 P.O. Box 429 Columbia, MD 21045 Gentlemen: By signature below, we hereby appoint US Tech employees Sandi McEnery, Alan Ghasiani and George Yang to act as our agents with regard to all FCC equipment authorizations. This appointment will remain in effect until otherwise notified. I further certify by signature below that no party (per 47 CFR 1.2002(b)) to the application is subject to a denial of Federal benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). This appointment includes the authority to complete FCC Form 731 on our behalf and sign the application as an authorized agent. Signature: ________________________ Name: Cindy Allen Title: Product Safety and Regulatory Specialist Date: 9/18/2012

FCC Confidentiality Request April 12, 2013 Timco Engineering PO Box 370 Newberry, FL 32669 RE : FCC ID: KE3-3002539 Dear Applications Examiner: With regards to the exhibits submitted in support of the application for FCC ID: KE3-3002539, please classify the following as confidential under the provision of 47 CFR 0.459: -Schematics - File Name: 13-0006.Radio Systems.300-2539.CONFIDENTIAL Schematics.pdf - Block Diagram – File Name: 13-0006.Radio Systems.300-2539.CONFIDENTIAL Block Diagram.pdf -Operational Description – File Name: 13-0006.Radio Systems.300-2539.CONFIDENTIAL ToO.pdf These exhibits contain technical information that Radio Systems Corp. deems to be sensitive and proprietary. Therefore this information cannot be published. If this information were to be made public it could be used to the disadvantage of the applicant in the marketplace. Sincerely, Sandi McEnery US Tech (Authorized Agent for Radio Systems Corp.) 3505 Francis Circle Alpharetta, GA 30004 PH: 770-740-0717 Fax: 770-740-1508 www.ustech-lab.com

US Tech Test Report: FCC P15.209/IC RSS-210 Report Number: 13-0006 Issue Date: April 12, 2013 Customer: Radio Systems Corporation Model: 300-2539 FCC ID: KE3-3002539 IC: 2721A-3002539 Page 1 of 11 External Photographs Figure 1- EUT - Front US Tech Test Report: FCC P15.209/IC RSS-210 Report Number: 13-0006 Issue Date: April 12, 2013 Customer: Radio Systems Corporation Model: 300-2539 FCC ID: KE3-3002539 IC: 2721A-3002539 Page 2 of 11 Figure 2- EUT w Exterior Frame US Tech Test Report: FCC P15.209/IC RSS-210 Report Number: 13-0006 Issue Date: April 12, 2013 Customer: Radio Systems Corporation Model: 300-2539 FCC ID: KE3-3002539 IC: 2721A-3002539 Page 3 of 11 Figure 3- EUT - Side 1 US Tech Test Report: FCC P15.209/IC RSS-210 Report Number: 13-0006 Issue Date: April 12, 2013 Customer: Radio Systems Corporation Model: 300-2539 FCC ID: KE3-3002539 IC: 2721A-3002539 Page 4 of 11 Figure 4- EUT - Side 2 US Tech Test Report: FCC P15.209/IC RSS-210 Report Number: 13-0006 Issue Date: April 12, 2013 Customer: Radio Systems Corporation Model: 300-2539 FCC ID: KE3-3002539 IC: 2721A-3002539 Page 5 of 11 Figure 5- EUT -Top US Tech Test Report: FCC P15.209/IC RSS-210 Report Number: 13-0006 Issue Date: April 12, 2013 Customer: Radio Systems Corporation Model: 300-2539 FCC ID: KE3-3002539 IC: 2721A-3002539 Page 6 of 11 Figure 6- EUT - Bottom US Tech Test Report: FCC P15.209/IC RSS-210 Report Number: 13-0006 Issue Date: April 12, 2013 Customer: Radio Systems Corporation Model: 300-2539 FCC ID: KE3-3002539 IC: 2721A-3002539 Page 7 of 11 Figure 7- EUT - User Control Panel Closed US Tech Test Report: FCC P15.209/IC RSS-210 Report Number: 13-0006 Issue Date: April 12, 2013 Customer: Radio Systems Corporation Model: 300-2539 FCC ID: KE3-3002539 IC: 2721A-3002539 Page 8 of 11 Figure 8- EUT - User Control Panel Open US Tech Test Report: FCC P15.209/IC RSS-210 Report Number: 13-0006 Issue Date: April 12, 2013 Customer: Radio Systems Corporation Model: 300-2539 FCC ID: KE3-3002539 IC: 2721A-3002539 Page 9 of 11 Figure 9- EUT - Battery Compartment Closed US Tech Test Report: FCC P15.209/IC RSS-210 Report Number: 13-0006 Issue Date: April 12, 2013 Customer: Radio Systems Corporation Model: 300-2539 FCC ID: KE3-3002539 IC: 2721A-3002539 Page 10 of 11 Figure 10- EUT - Battery Compartment Open US Tech Test Report: FCC P15.209/IC RSS-210 Report Number: 13-0006 Issue Date: April 12, 2013 Customer: Radio Systems Corporation Model: 300-2539 FCC ID: KE3-3002539 IC: 2721A-3002539 Page 11 of 11 Figure 11- EUT - Pet Door Open

The world leader in pet training products RSC Part #: Label PN: 402-13801-17 for Medium Passport Door PN: 700-2936 Description: ARTWORK REGULATORY PASSPORT MEDIUM E/F Date: 04-18-13 Drawn By: MJ Printing: Silkscreen Black Ink Material: yupo paper WIN-W-100(CP)K Adhesive: Permanent Model #: PPA00-13796, 1020EF, 1020SGIFD Description: Multiple SKU’s Program used: AI CS5 This device complies with FCC and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. Model / Modèle: 300-2539 402-13801-17 N13506 Z1630 FCC: KE3-3002539 IC: 2721A-3002539 11.75” (298.45mm) .5” (12.7mm)

US Tech Test Report: FCC P15.209/IC RSS-210 Report Number: 13-0006 Issue Date: April 12, 2013 Customer: Radio Systems Corporation Model: 300-2539 FCC ID: KE3-3002539 IC: 2721A-3002539 Page 1 of 8 INTERNAL PHOTOGRAPHS Figure 1- Back half of EUT US Tech Test Report: FCC P15.209/IC RSS-210 Report Number: 13-0006 Issue Date: April 12, 2013 Customer: Radio Systems Corporation Model: 300-2539 FCC ID: KE3-3002539 IC: 2721A-3002539 Page 2 of 8 Figure 2- Front half of EUT US Tech Test Report: FCC P15.209/IC RSS-210 Report Number: 13-0006 Issue Date: April 12, 2013 Customer: Radio Systems Corporation Model: 300-2539 FCC ID: KE3-3002539 IC: 2721A-3002539 Page 3 of 8 Figure 3- Common mode filter, component side Figure 4- Solder side US Tech Test Report: FCC P15.209/IC RSS-210 Report Number: 13-0006 Issue Date: April 12, 2013 Customer: Radio Systems Corporation Model: 300-2539 FCC ID: KE3-3002539 IC: 2721A-3002539 Page 4 of 8 Figure 5- Main PCB w/ LCD Display – Top Side Figure 6- Main PCB – Bottom Side US Tech Test Report: FCC P15.209/IC RSS-210 Report Number: 13-0006 Issue Date: April 12, 2013 Customer: Radio Systems Corporation Model: 300-2539 FCC ID: KE3-3002539 IC: 2721A-3002539 Page 5 of 8 Figure 7- Modification on main PCB (see schematic for details) US Tech Test Report: FCC P15.209/IC RSS-210 Report Number: 13-0006 Issue Date: April 12, 2013 Customer: Radio Systems Corporation Model: 300-2539 FCC ID: KE3-3002539 IC: 2721A-3002539 Page 6 of 8 Figure 8- Sensor, Component Side US Tech Test Report: FCC P15.209/IC RSS-210 Report Number: 13-0006 Issue Date: April 12, 2013 Customer: Radio Systems Corporation Model: 300-2539 FCC ID: KE3-3002539 IC: 2721A-3002539 Page 7 of 8 Figure 9- Sensor, Solder Side US Tech Test Report: FCC P15.209/IC RSS-210 Report Number: 13-0006 Issue Date: April 12, 2013 Customer: Radio Systems Corporation Model: 300-2539 FCC ID: KE3-3002539 IC: 2721A-3002539 Page 8 of 8 Figure 10- Battery PCB, Component Side Figure 11- Solder Side

Application for Certification Per Title 47 USC Part 2, Subpart J, Equipment Authorization Procedures, Paragraph 2.907, Certification and Part 15, Subpart C, Intentional Radiators, Paragraph 15.207, Conducted limits and 209, Radiated emission limits; general requirements. For the Radio Systems Corporation Model: 300-2539 PASSport Pet Access Smart System Medium UST Project: 13-0006 Issue Date: April 8, 2013 Number of Pages in this report: 21 3505 Francis Circle Alpharetta, GA 30004 PH: 770-740-0717 Fax: 770-740-1508 www.ustech-lab.com Page 1 of 21 I certify that I am authorized to sign for the test facility and that all of the statements in this report and in the Exhibits attached hereto are true and correct to the best of my knowledge and belief: Page 2 of 21 US Tech (Agent Responsible For Test): By: Name: Alan Ghasiani__________ Title: President – Consulting Engineer Date: April 8, 2013 This report shall not be reproduced except in full. The results contained in this report are subject to the adequacy and representative character of the sample provided. This test report must not be used to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. 3505 Francis Circle Alpharetta, GA 30004 PH: 770-740-0717 Fax: 770-740-1508 www.ustech-lab.com US Tech Test Report: FCC Part 15.209/ RSS-210 Issue Date: April 8, 2013 Report Number: 13-0006 Customer: Radio Systems Corporation Model 300-2539 FCC ID: KE3-3002539 IC: 2721A-3002539 Page 3 of 21 MEASUREMENT/TECHNICAL REPORT COMPANY NAME: Radio Systems Corporation MODEL: 300-2539 FCC ID: KE3-3002539 IC: 2721A-3002539 DATE: April 8, 2013 This report concerns (check one): Original grant X Class II change_____ Equipment type: 134.2 kHz intentional transmitter Deferred grant requested per 47 CFR 0.457(d)(1)(ii)? yes_____ No X If yes, defer until:_________________ date N.A. agrees to notify the Commission by N.A. date of the intended date of announcement of the product so that the grant can be issued on that date. Report prepared by: US Tech 3505 Francis Circle Alpharetta, GA 30004 Phone Number: (770) 740-0717 Fax Number: (770) 740-1508 US Tech Test Report: FCC Part 15.209/ RSS-210 Issue Date: April 8, 2013 Report Number: 13-0006 Customer: Radio Systems Corporation Model 300-2539 FCC ID: KE3-3002539 IC: 2721A-3002539 Page 4 of 21 Table of Contents Paragraph Title Page 1. General Information................................................................................................. 6 1.1 Product Description............................................................................................ 6 1.2 Characterization of Test Sample....................................................................... 6 1.3 Related Submittal(s)/Grant(s)............................................................................. 6 1.4 The EUT is subject to the following authorizations:............................................ 6 2. Tests and Measurements......................................................................................... 7 2.1 Configuration of Tested System........................................................................ 7 2.2 Test Facility........................................................................................................ 7 2.3 Test Equipment.................................................................................................. 7 2.4 Modifications to Equipment................................................................................ 9 2.5 Test Procedure............................................................................................. 10 2.5.1 Number of Measurements for Intentional Radiators (15.31(m)).................... 10 2.5.2 Frequency Range of Radiated Emissions (Part 15.33(a)/RSS Gen 4.10)..... 11 2.6 EUT Antenna Description (FCC Sec. 15.203)............................................... 13 2.7 Field Strength of Fundamental (47 CFR 15.209)............................................. 14 2.8 Intentional Radiated Emissions, 9 kHz to 30 MHz (47 CFR 15.205, 15.209)... 15 2.9 Bandwidth of Fundamental (RSS-210, A8.1(a)).............................................. 16 2.10 Power Line Conducted Emissions for Transmitter and Receiver/Digital Apparatus (47 CFR 15.107/15.207)........................................................................... 17 2.11 Unintentional Radiator Radiated Emissions (47 CFR 15.33(a); 15.109/209)19 2.12 Measurement Uncertainty............................................................................. 21 2.12.1 Conducted Emissions Measurement Uncertainty........................................ 21 2.12.2 Radiated Emissions Measurement Uncertainty........................................... 21 US Tech Test Report: FCC Part 15.209/ RSS-210 Issue Date: April 8, 2013 Report Number: 13-0006 Customer: Radio Systems Corporation Model 300-2539 FCC ID: KE3-3002539 IC: 2721A-3002539 Page 5 of 21 Table of Contents (cont’d.) List of Figures Figure Title Page Figure 1. Test Configuration .......................................................................................... 12 Figure 2. Occupied Bandwidth ...................................................................................... 16 List of Tables Tables Title Page Table 1. EUT and Peripherals ......................................................................................... 7 Table 2. Test Instruments................................................................................................ 8 Table 3. Number of Test Frequencies for Intentional Radiators .................................... 10 Table 4. Antenna Description ........................................................................................ 13 Table 5. Intentional Radiated Emissions (9kHz to 30 MHz) .......................................... 15 Table 6. Unintentional Powerline Conducted Emissions ............................................... 18 Table 7. Spurious Radiated Emis…

Text truncated - open the document above for the full version.

US Tech Test Report: FCC Part 15.209/ RSS-210 Issue Date: April 8, 2013 Report Number: 13-0006 Customer: Radio Systems Corporation Model 300-2539 FCC ID: KE3-3002539 IC: 2721A-3002539 Page 1 of 1 Extrapolation factor The EUT operates at below 30 MHz, 134.2 kHz. Therefore per FCC Part 15.31f(2) sited below; measurements were made at two distances to determine the appropriate factor to use. (2) At frequencies below 30 MHz, measurements may be performed at a distance closer than that specified in the regulations; however, an attempt should be made to avoid making measurements in the near field. Pending the development of an appropriate measurement procedure for measurements performed below 30 MHz, when performing measurements at a closer distance than specified, the results shall be extrapolated to the specified distance by either making measurements at a minimum of two distances on at least one radial to determine the proper extrapolation factor or by using the square of an inverse linear distance extrapolation factor (40 dB/decade). This paragraph (f) shall not apply to Access BPL devices operating below 30 MHz. For this product measurements were taken at two distances to determine the extrapolation factor. The distance and the measurement collected are presented below: 1. 1 meter= fundamental reading of 83.4 dBuV 2. 10 meter= fundamental reading of 34.0 dBuV The results show a factor of 49.4 dB/decade. This factor was used to determine the fundamental emissions limit for the EUT.

US Tech Test Report: FCC Part 15.209/ RSS-210 Issue Date: April 12, 2013 Report Number: 13-0006 Customer: Radio Systems Corporation Model: 300-2539 FCC ID: KE3-3002539 IC: 2721A-3002539 Page 1 of 5 Test Configuration Photographs Figure 1- Radiated Emissions, Front view US Tech Test Report: FCC Part 15.209/ RSS-210 Issue Date: April 12, 2013 Report Number: 13-0006 Customer: Radio Systems Corporation Model: 300-2539 FCC ID: KE3-3002539 IC: 2721A-3002539 Page 2 of 5 Figure 2- Radiated Emissions, Low Frequency (LOOP) US Tech Test Report: FCC Part 15.209/ RSS-210 Issue Date: April 12, 2013 Report Number: 13-0006 Customer: Radio Systems Corporation Model: 300-2539 FCC ID: KE3-3002539 IC: 2721A-3002539 Page 3 of 5 Figure 3- Radiated Emissions, Low Frequency (BiCon) US Tech Test Report: FCC Part 15.209/ RSS-210 Issue Date: April 12, 2013 Report Number: 13-0006 Customer: Radio Systems Corporation Model: 300-2539 FCC ID: KE3-3002539 IC: 2721A-3002539 Page 4 of 5 Figure 4- Radiated Emissions, High Frequency (Log Periodic) US Tech Test Report: FCC Part 15.209/ RSS-210 Issue Date: April 12, 2013 Report Number: 13-0006 Customer: Radio Systems Corporation Model: 300-2539 FCC ID: KE3-3002539 IC: 2721A-3002539 Page 5 of 5 Figure 5- Conducted Emissions