KE3-300290210.7 kHz low power transmitter

Invisible Gate ® Plus Owner’s Manual Please read this entire guide before operating. www.InvisibleFence.com www.InvisibleFence.com 2 Important Precautions  Invisible Fence ® Brand pet containment systems have contained over two million pets. However, there are some precautions you should take.  Read and retain manuals: Read the entire Owner’s Manual before using your new Invisible Gate ® Plus solution. If you have any questions after reading this manual, call your Invisible Fence® Brand dealer.  Adhere to all warnings and cautions contained in any Invisible Fence ® Brand manual. Explanation of Attention Words and Symbols used in this guide This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury. CAUTION used with the safety alert symbol, indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. CAUTION used without the safety alert symbol, indicates a hazardous situation which, if not avoided, could result in harm to your pet. NOTICE is used to address safe use practices not related to personal injury.  Not every pet can be trained to avoid the established boundary. Sometimes even a properly trained pet may cross the boundary. Therefore, Invisible Fence, Inc., as well as Invisible Fence ® Brand Distributors and Dealers cannot guarantee the system will, in all cases, keep a customer’s pet within the established boundary. Accordingly, if a customer has reason to believe that their pet may pose a danger to others, or harm itself, the customer should not rely solely upon the Invisible Fence ® Brand system to keep the pet from crossing the boundary.  Do not install, connect, or remove your system during a lightning storm. If the storm is close enough for you to hear thunder, it is close enough to create hazardous surges. www.InvisibleFence.com 3  Read and follow the important tips on how to avoid pressure necrosis in your Invisible Fence ® Brand Computer Collar ® unit manual.  Train your pet according to the instructions in the Invisible Fence ® Brand training protocols. Complete all steps before allowing your pet to run free. Do not become overly confident if your pet has become conditioned to the Invisible Fence ® Brand pet containment system sooner than expected.  Your Invisible Fence ® Brand dealer has professionally installed your pet avoidance system and ensured it is working properly. You will want to perform periodic maintenance checks to make sure the system is properly functioning.  Check the Invisible Fence ® Brand transmitter periodically to make sure it is operating properly. To do this, simply bring the Computer Collar ® unit to the edge of the signal field to verify function.  Do not attempt to service any Invisible Fence ® Brand equipment. Refer all service to your authorized Invisible Fence ® Brand dealer. Only your authorized Invisible Fence ® Brand dealer should make adjustments to your pet avoidance/containment system.  All Invisible Fence ® Brand pet containment systems are designed for domesticated animal use only. Never attempt to use this product for any purpose not specifically described in this manual.  Congratulations on your purchase of the Invisible Gate ® Plus solution. Please read and review this entire manual to become familiar with Invisible Gate ® Plus solution components and its operation. It is strongly recommended you review this information before using the product.  The Invisible Gate ® Plus solution gives you control over the areas a pet or pets have access to inside your home. It is designed to work independently or to complement your Invisible Fence ® Brand 800 Series and/or Boundary Plus ® digital electronic pet containment system. The Invisible Gate ® Plus transmitter is designed for indoor use only. For information on or about Outdoor Shields ® products, please contact your local Invisible Fence ® Brand dealer or visit us at www.invisiblefence.com. This device is not designed to operate as a containment transmitter.  Important: To ensure your pet does not receive an unintended correction, make sure your pet is not wearing the Computer Collar ® Unit when turning ON or adjusting the Invisible Gate ® Plus transmitter. www.InvisibleFence.com 4 Table of Contents Important Precautions ................................................................................................................. 2-3 Components .............................................................................................................................. 5 How the System Works ............................................................................................................. 5 Operating Guide ................................................................................................................... 6 Charging ..................................................................................................................... 6 Turning On and Off ..................................................................................................... 6 Control Panel .................................................................................................................. 7 Shields ® Operation ........................................................................................................ 7-8 Adjust Signal Field Range ................................................................................... 7 Verify Signal Field Range .................................................................................... 8 Changing the Channel Setting ................................................................................. 8 Boundary Plus ® Operation ................................................................................................. 8-9 Adjust Signal Field Ra…

Text truncated - open the document above for the full version.

Request for Confidentiality Date: ___December 9, 2014_____ Subject: Confidentiality Request for: ___FCC ID:KE3-3002902 IC: 2721A-3002902_ Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 10, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Exhibit Short Term Permanent Block Diagrams Short Term External Photos Short Term Permanent Internal Photos Short Term Permanent Operation Description/Theory of Operation Short Term Permanent Parts List & Placement/BOM Short Term Permanent Tune-Up Procedure Short Term Permanent Schematics Short Term Test Setup Photos Short Term Permanent* User’s Manual Radio Systems has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. NOTE for Industry Canada Applications: The applicant understands that until such time that IC distinguishes between Short Term and Permanent Confidentiality, either type of marked exhibit above will simply be marked Confidential when submitted to IC. Sincerely, By:__________________________ ___Sandi McEnery__- Agent (Signature/Title 1 ) (Print name)

10427 PetSafe Way Knoxville, TN. 37932 865-777-5404 www.petsafe.net AGENCY AGREEMENT Federal Communications Commission Date: 9/18/2012 P.O. Box 429 Columbia, MD 21045 Gentlemen: By signature below, we hereby appoint US Tech employees Sandi McEnery, Alan Ghasiani and George Yang to act as our agents with regard to all FCC equipment authorizations. This appointment will remain in effect until otherwise notified. I further certify by signature below that no party (per 47 CFR 1.2002(b)) to the application is subject to a denial of Federal benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). This appointment includes the authority to complete FCC Form 731 on our behalf and sign the application as an authorized agent. Signature: ________________________ Name: Cindy Allen Title: Product Safety and Regulatory Specialist Date: 9/18/2012

US Tech Test Report: FCC Part 15 Certification/ RSS 210 FCC ID: KE3-3002902 IC: 2721A-3002902 Test Report Number: 14-0290 Issue Date: December 9, 2014 Customer: Radio Systems Model: RAC17-14682 Page 1 of 2 EXTERNAL PHOTOGRAPHS Figure 1. Top of EUT US Tech Test Report: FCC Part 15 Certification/ RSS 210 FCC ID: KE3-3002902 IC: 2721A-3002902 Test Report Number: 14-0290 Issue Date: December 9, 2014 Customer: Radio Systems Model: RAC17-14682 Page 2 of 2 Figure 2. Back of EUT

US Tech Test Report: FCC Part 15 Certification/ RSS 210 FCC ID: KE3-3002902 IC: 2721A-3002902 Test Report Number: 14-0290 Issue Date: December 9, 2014 Customer: Radio Systems Model: RAC17-14682 LABEL LOCATION Label will be placed on back of product as pictured above; see following page for Label Details. 65.0mm 30.0mm R4.00 INVISIBLE GATE ® PLUS Model / Modèle: RAC17-14682 REV:XXX FCC ID: KE3-3002902 IC: 2721A-3002902 Input: 5V , 0.5A Made in China Fabriqué en Chine 402-15668 Invisible Fence, Inc. US Patents / Brevets Américains: 7068174, 7278376, 7495570 Patents pending / Brevets en Instance 3. CE MARK AS PROVIDED BY THE EUROPEAN COMMISION. A MIMIMUM HEIGHT OF 5mm IS REQUIRED. CE MARK CONFORMITY MARKING SHALL BE IN ACCORDANCE WITH COUNCIL DECISION Material: PET Color: White Printing: Black Process: Inkjet Printed Coating: Anti-friction RSC Part #: 402-15668 Description: LABEL FCC UNIT BARCODE RAC17-14682 Created by: Kendy Lai Initial Creation Date: Dec.18.2014 Approved by: Kevin Tolliver Date Approved: Dec.23.2014 Program used: ILLUSTRATOR CS6 Revision: ECO: RSC11519 Revision Description: RELEASE TO PRODUCTION Revision Date: N/A 000 XXXXXXXXXXXXX BAR CODE PRINTS HERE This device complies with Industry Canada licence-exempt RSS standard(s). This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. Cet appareil est conforme à la partie 15 des régles FCC. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

US Tech Test Report: FCC Part 15 Certification/ RSS 210 FCC ID: KE3-3002902 IC: 2721A-3002902 Test Report Number: 14-0290 Issue Date: December 9, 2014 Customer: Radio Systems Model: RAC17-14682 Page 1 of 11 INTERNAL PHOTOGRAPHS Figure 1. Back of EUT with External Plate Removed US Tech Test Report: FCC Part 15 Certification/ RSS 210 FCC ID: KE3-3002902 IC: 2721A-3002902 Test Report Number: 14-0290 Issue Date: December 9, 2014 Customer: Radio Systems Model: RAC17-14682 Page 2 of 11 Figure 2. Back of EUT with External Cover Removed US Tech Test Report: FCC Part 15 Certification/ RSS 210 FCC ID: KE3-3002902 IC: 2721A-3002902 Test Report Number: 14-0290 Issue Date: December 9, 2014 Customer: Radio Systems Model: RAC17-14682 Page 3 of 11 Figure 3. Close Up of EUT with #1 Cover Removed US Tech Test Report: FCC Part 15 Certification/ RSS 210 FCC ID: KE3-3002902 IC: 2721A-3002902 Test Report Number: 14-0290 Issue Date: December 9, 2014 Customer: Radio Systems Model: RAC17-14682 Page 4 of 11 Figure 4. Close up of EUT with # 2 Cover Removed US Tech Test Report: FCC Part 15 Certification/ RSS 210 FCC ID: KE3-3002902 IC: 2721A-3002902 Test Report Number: 14-0290 Issue Date: December 9, 2014 Customer: Radio Systems Model: RAC17-14682 Page 5 of 11 Figure 5. Close up of EUT with # 3 Cover Removed US Tech Test Report: FCC Part 15 Certification/ RSS 210 FCC ID: KE3-3002902 IC: 2721A-3002902 Test Report Number: 14-0290 Issue Date: December 9, 2014 Customer: Radio Systems Model: RAC17-14682 Page 6 of 11 Figure 6. Front of PCB #1 US Tech Test Report: FCC Part 15 Certification/ RSS 210 FCC ID: KE3-3002902 IC: 2721A-3002902 Test Report Number: 14-0290 Issue Date: December 9, 2014 Customer: Radio Systems Model: RAC17-14682 Page 7 of 11 Figure 7. Back of PCB #1 US Tech Test Report: FCC Part 15 Certification/ RSS 210 FCC ID: KE3-3002902 IC: 2721A-3002902 Test Report Number: 14-0290 Issue Date: December 9, 2014 Customer: Radio Systems Model: RAC17-14682 Page 8 of 11 Figure 8. Front of PCB with Radio US Tech Test Report: FCC Part 15 Certification/ RSS 210 FCC ID: KE3-3002902 IC: 2721A-3002902 Test Report Number: 14-0290 Issue Date: December 9, 2014 Customer: Radio Systems Model: RAC17-14682 Page 9 of 11 Figure 9. Back of PCB with Radio US Tech Test Report: FCC Part 15 Certification/ RSS 210 FCC ID: KE3-3002902 IC: 2721A-3002902 Test Report Number: 14-0290 Issue Date: December 9, 2014 Customer: Radio Systems Model: RAC17-14682 Page 10 of 11 Figure 10. Front of PCB # 2 US Tech Test Report: FCC Part 15 Certification/ RSS 210 FCC ID: KE3-3002902 IC: 2721A-3002902 Test Report Number: 14-0290 Issue Date: December 9, 2014 Customer: Radio Systems Model: RAC17-14682 Page 11 of 11 Figure 11. Back of PCB #2

Page 1 of 23 Application For Title 47 USC Part 2, Subpart J, Paragraph 2.907 Equipment Authorization of Certification for an Intentional Radiator per Part 15, Subpart C, Paragraphs 15.207 and 15.209 And Industry Canada, Radio Standards Specifications: RSS Gen Issue 4 and RSS-210 Issue 8 For the Radio Systems Model: RAC17-14682 FCC ID: KE3-3002902 IC: 2721A-3002902 UST Project: 14-0290 Issue Date: December 9, 2014 Total Pages in This Report: 23 3505 Francis Circle Alpharetta, GA 30004 PH: 770-740-0717 Fax: 770-740-1508 www.ustech-lab.com Page 2 of 23 I certify that I am authorized to sign for the Test Agency and that all of the statements in this report and in the Exhibits attached hereto are true and correct to the best of my knowledge and belief: US TECH (Agent Responsible For Test): By: Alan Ghasiani Name: Title: Compliance Engineer – President Date December 9, 2014 This report shall not be reproduced except in full. This report may be copied in part only with the prior written approval of US Tech. The results contained in this report are subject to the adequacy and representative character of the sample provided. This report must not be used to claim product certification, approval, or endorsement by NVLAP, NIST or any agency of the Federal Government. 3505 Francis Circle Alpharetta, GA 30004 PH: 770-740-0717 Fax: 770-740-1508 www.ustech-lab.com US Tech Test Report: FCC Part 15 Certification/ RSS 210 FCC ID: KE3-3002902 IC: 2721A-3002902 Test Report Number: 14-0290 Issue Date: December 9, 2014 Customer: Radio Systems Model: RAC17-14682 Page 3 of 23 MEASUREMENT TECHNICAL REPORT COMPANY NAME: Radio Systems MODEL: RAC17-14682 FCC ID: KE3-3002902 IC: 2721A-3002902 DATE: December 9, 2014 This report concerns (check one): Original grant X Class II change Equipment type: 7.5 kHz or 10.7 kHz Transmitter Module Deferred grant requested per 47 CFR 0.457(d)(1)(ii)? yes_____ No X If yes, defer until: ______N/A___________ date agrees to notify the Commission by N/A date of the intended date of announcement of the product so that the grant can be issued on that date. Report prepared by: US Tech 3505 Francis Circle Alpharetta, GA 30004 Phone Number: (770) 740-0717 Fax Number: (770) 740-1508 US Tech Test Report: FCC Part 15 Certification/ RSS 210 FCC ID: KE3-3002902 IC: 2721A-3002902 Test Report Number: 14-0290 Issue Date: December 9, 2014 Customer: Radio Systems Model: RAC17-14682 Page 4 of 23 Table of Contents Paragraph Title Page 1 General Information .......................................................................................... 6 1.1 Purpose of this Report .................................................................................. 6 1.2 Characterization of Test Sample ................................................................... 6 1.3 Product Description ...................................................................................... 6 1.4 Configuration of Tested System .................................................................... 7 1.5 Test Facility ................................................................................................... 7 2 Tests and Measurements ................................................................................. 8 2.1 Test Equipment ............................................................................................. 9 2.2 Modifications to EUT Hardware .................................................................... 9 2.3 Number of Measurements for Intentional Radiators (15.31(m)) .................. 10 2.4 Frequency Range of Radiated Measurements (Part 15.33)........................ 10 2.4.1 Intentional Radiator ................................................................................. 10 2.4.2 Unintentional Radiator ............................................................................ 10 2.5 Measurement Detector Function and Bandwidth (CFR 15.35) ................... 11 2.5.1 Detector Function and Associated Bandwidth ........................................ 11 2.5.2 Corresponding Peak and Average Requirements ................................... 11 2.5.3 Pulsed Transmitter Averaging ................................................................. 11 2.6 EUT Antenna Requirements (CFR 15.203) ................................................ 11 2.7 Restricted Bands of Operation (Part 15.205) .............................................. 13 2.8 Intentional Radiator, Power Line Conducted Emissions (CFR 15.207) ....... 13 2.9 Intentional Radiator, Radiated Emissions (CFR 15.209, (IC RSS 210)) ..... 13 2.10 99% Occupied Bandwidth (IC RSS 210, A8.1) ........................................... 16 2.11 Unintentional/Intentional Radiator, Power line Emissions (CFR 15.107 and 15.207) ................................................................................................................. 18 2.12 Unintentional/Intentional Radiator, Radiated Emissions (CFR 15.109 and 15.209) ................................................................................................................. 20 2.13 Measurement Uncertainty .......................................................................... 23 2.13.1 Conducted Emissions Measurement Uncertainty ................................. 23 2.13.2 Radiated Emissions Measurement Uncertainty .................................... 23 US Tech Test Report: FCC Part 15 Certification/ RSS 210 FCC ID: KE3-3002902 IC: 2721A-3002902 Test Report Number: 14-0290 Issue Date: December 9, 2014 Customer: Radio Systems Model: RAC17-14682 Page 5 of 23 List of Figures Figures Title Page Figure 1. Test Configuration .................................................................................... 12 Figure 2. 20 dB & 99% Bandwidth ........................................................................... 17 List of Tables Table Title Page Table 1. EUT and Peripherals .................................................................................... 8 Table 2. Test Instr…

Text truncated - open the document above for the full version.

US Tech Test Report: FCC Part 15 Certification/ RSS 210 FCC ID: KE3-3002902 IC: 2721A-3002902 Test Report Number: 14-0290 Issue Date: December 9, 2014 Customer: Radio Systems Model: RAC17-14682 Page 1 of 5 TEST CONFIGURATION PHOTOGRAPHS Figure 1. Radiated Emissions Test Setup, Front US Tech Test Report: FCC Part 15 Certification/ RSS 210 FCC ID: KE3-3002902 IC: 2721A-3002902 Test Report Number: 14-0290 Issue Date: December 9, 2014 Customer: Radio Systems Model: RAC17-14682 Page 2 of 5 Figure 2. Radiated Emissions Test Setup, .09 MHz to 300 MHz, Back US Tech Test Report: FCC Part 15 Certification/ RSS 210 FCC ID: KE3-3002902 IC: 2721A-3002902 Test Report Number: 14-0290 Issue Date: December 9, 2014 Customer: Radio Systems Model: RAC17-14682 Page 3 of 5 Figure 3. Radiated Emissions Test Setup, 30 MHz to 200 MHz, Back US Tech Test Report: FCC Part 15 Certification/ RSS 210 FCC ID: KE3-3002902 IC: 2721A-3002902 Test Report Number: 14-0290 Issue Date: December 9, 2014 Customer: Radio Systems Model: RAC17-14682 Page 4 of 5 Figure 4. Radiated Emissions Test Setup, 200 MHz to 1GHz, Back US Tech Test Report: FCC Part 15 Certification/ RSS 210 FCC ID: KE3-3002902 IC: 2721A-3002902 Test Report Number: 14-0290 Issue Date: December 9, 2014 Customer: Radio Systems Model: RAC17-14682 Page 5 of 5 Figure 5. Conducted Emissions Test Setup