KE3-300306110.65 kHz low power transmitter

OPERATING & TRAINING GUIDE PLEASE READ THIS ENTIRE GUIDE BEFORE BEGINNING 2 1-800-732-0144 SPORTDOG.COM 3 IMPORTANT SAFETY INFORMATION Explanation of Attention Words and Symbols used in this guide This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury. CAUTION, used with the safety alert symbol, indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. CAUTION, used without the safety alert symbol, indicates a hazardous situation which, if not avoided, could result in harm to your dog. NOTICE is used to address safe use practices not related to personal injury. • Not for use with aggressive dogs. Do not use this product if your dog is prone to aggressive behavior. Aggressive dogs can cause severe injury or death to their owners and others. If you are not sure that this product is right for your dog, please talk to your veterinarian or a certified trainer. • Underground cables can carry high voltage. Have all underground cables marked before you dig to bury your wire. In most areas, this is a free service. Avoid these cables when you dig. • Follow all safety instructions for your power tools. Be sure to always wear your safety goggles. • Do not install, connect, or remove your system during a lightning storm. If the storm is close enough for you to hear thunder, it is close enough to create hazardous surges. • Risk of electric shock. Use the Fence Transmitter indoors in a dry location only. • Risk of injury. Wire on top of the ground may be a trip hazard. Use care in how you place your wires. • If possible, DO NOT use an AC circuit with a GFCI (ground fault circuit interrupter). In rare cases, nearby lightning may cause the GFCI to trip. Without power to the system, your dog may escape. You will have to reset the GFCI to restore power. This SportDOG Brand ® In-Ground Fence is NOT a solid barrier. The system is designed to act as a deterrent to remind dogs by stimulation to remain in the boundary established. It is important that you reinforce training with your dog on a regular basis. Since the tolerance level to stimulation varies from one dog to the next, Radio Systems ® Corporation CANNOT guarantee that the system will, in all cases, keep a dog within the established boundary. Not all dogs can be trained to avoid crossing the boundary! Therefore, if you have reason to believe that your dog may pose a danger to others or harm himself if he is not kept from crossing the boundaries, you should NOT rely solely upon the SportDOG Brand In-Ground Fence to confine your dog. Radio Systems Corporation shall NOT be liable for any property damage, economic loss or any consequential damages, sustained as a result of any animal crossing the boundary. Please read and follow the instructions in this manual. Proper fit of the collar is important. A collar worn for too long or made too tight on the dog’s neck may cause skin damage. Ranging from redness to pressure ulcers; this condition is commonly known as bed sores. • Avoid leaving the collar on the dog for more than 12 hours per day. • When possible reposition the collar on the dog’s neck every 1 to 2 hours. • Check the fit to prevent excessive pressure; follow the instructions in this manual. • Never connect a leash to the electronic collar; it will cause excessive pressure on the contacts. • When using a separate collar for a leash, don’t put pressure on the electronic collar. • Wash the dog’s neck area and the contacts of the collar weekly with a damp cloth. • Examine the contact area daily for signs of a rash or a sore. • If a rash or sore is found, discontinue use of the collar until the skin has healed. • If the condition persists beyond 48 hours, see your veterinarian. • For additional information on bed sores and pressure necrosis, please visit the FAQ section for in-ground containment at www.sportdog.com. These steps will help keep your dog safe and comfortable. Millions of dogs are comfortable while they wear stainless steel contacts. Some dogs are sensitive to contact pressure. You may find after some time that your dog is very tolerant of the collar. If so, you may relax some of these precautions. It is important to continue daily checks of the contact area. If redness or sores are found, discontinue use until the skin has fully healed. You may need to trim the hair in the area of the Contact Points or switch to the longer Contact Points to ensure consistent contact. Never shave the dog’s neck; this may lead to a rash or infection. To prevent an unintended correction: • The Collar Receiver should not be on your dog when the system is tested. • Remove the Collar Receiver before making any changes to your system. • Before placing the Collar Receiver on your dog, test the Boundary Area and Width after any change. • Use care when mowing or trimming your grass not to cut the loop wire. • For added protection, when unused for long periods of time or prior to thunderstorms, unplug from the wall outlet and disconnect the Loop Boundary Wires. This will prevent damage to the Transmitter due to surges. • Avoid damage to the jacket of the loop wire during the install; damage may cause areas of weak signal and lead to early failure of the loop (wire breaks). 4 1-800-732-0144 SPORTDOG.COM 5 Thank you for choosing SportDOG Brand. ® Used properly, this product will help you train your dog efficiently and safely. To ensure your satisfaction, please review this owner’s manual thoroughly. If you have questions regarding this product’s operation, please see this manual’s Frequently Asked Questions or Troubleshooting section, contact our Customer Care Center at 1-800-732-0144, or visit our website at www.sportdog.com. To get the most protection out of your warranty, please register your product wit…

Text truncated - open the document above for the full version.

IC and FCC Statement addendum to replace current manual verbiage: This device complies with Industry Canada License-exempt RSS Rules. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Unauthorized changes or modifications to the equipment, not approved by Radio Systems® Corporation, could result in not meeting compliance with FCC regulations and could void the user’s authority to operate the equipment.

Request for Confidentiality Date: ___February 19, 2015_____ Subject: Confidentiality Request for: ___FCC ID:KE3-3003061 IC: 2721A-3003061_ Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 6, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Exhibit Short Term Permanent Block Diagrams Short Term External Photos Short Term Permanent Internal Photos Short Term Permanent Operation Description/Theory of Operation Short Term Permanent Parts List & Placement/BOM Short Term Permanent Tune-Up Procedure Short Term Permanent Schematics Short Term Test Setup Photos Short Term Permanent* User’s Manual Radio Systems has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. NOTE for Industry Canada Applications: The applicant understands that until such time that IC distinguishes between Short Term and Permanent Confidentiality, either type of marked exhibit above will simply be marked Confidential when submitted to IC. Sincerely, By:__________________________ ___Sandi McEnery__- Agent (Signature/Title 1 ) (Print name)

CROSS REFERENCE FCC TO IC RSS-210/Gen For UST Project 15-0033 FCC ID: KE3-3003061 IC: 2721A-3003061 TEST IC RSS-210 ISSUE 8 IC RSS-Gen ISSUE 4 FCC 15.207 and 15.209 Transmit Antenna Requirement RSS-210, A8.4(4) 15.203 Fundamental Peak Power N/A N/A Antenna Conducted Spurious Emissions N/A N/A Restricted Bands RSS-210, 2.2 15.205 Bandwidths RSS-Gen 6.6 Transmitter Unwanted emissions RSS-Gen 6.13 RSS-Gen 8.9 15.209 Receiver Spurious emissions RSS-Gen 7.1 15.109 Frequency Strengths and Frequency Bandwidths RSS-210, A1.1.2 15.231(c) Power Spectral Density RSS-210, A8.5 N/A Conducted ICES-003 15.207(a) & 15.107(a) Digital Device Radiated ICES-003 15.109(a) Modular Approval RSS-Gen 2.1 N/A Antenna Requirement RSS-Gen 8.3 15.203

10427 PetSafe Way Knoxville, TN. 37932 865-777-5404 www.petsafe.net AGENCY AGREEMENT Federal Communications Commission Date: 9/18/2012 P.O. Box 429 Columbia, MD 21045 Gentlemen: By signature below, we hereby appoint US Tech employees Sandi McEnery, Alan Ghasiani and George Yang to act as our agents with regard to all FCC equipment authorizations. This appointment will remain in effect until otherwise notified. I further certify by signature below that no party (per 47 CFR 1.2002(b)) to the application is subject to a denial of Federal benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). This appointment includes the authority to complete FCC Form 731 on our behalf and sign the application as an authorized agent. Signature: ________________________ Name: Cindy Allen Title: Product Safety and Regulatory Specialist Date: 9/18/2012

US Tech Test Report: FCC Part 15 Certification/ RSS 210 FCC ID: KE3-3003061 IC: 2721A-3003061 Test Report Number: 15-0033 Issue Date: February 19, 2015 Customer: Radio Systems Model: SDT00-12721 Page 1 of 7 EXTERNAL PHOTOGRAPHS Figure 1. EUT with all Accessories US Tech Test Report: FCC Part 15 Certification/ RSS 210 FCC ID: KE3-3003061 IC: 2721A-3003061 Test Report Number: 15-0033 Issue Date: February 19, 2015 Customer: Radio Systems Model: SDT00-12721 Page 2 of 7 Figure 2. EUT Top US Tech Test Report: FCC Part 15 Certification/ RSS 210 FCC ID: KE3-3003061 IC: 2721A-3003061 Test Report Number: 15-0033 Issue Date: February 19, 2015 Customer: Radio Systems Model: SDT00-12721 Page 3 of 7 Figure 3. EUT Side 1 US Tech Test Report: FCC Part 15 Certification/ RSS 210 FCC ID: KE3-3003061 IC: 2721A-3003061 Test Report Number: 15-0033 Issue Date: February 19, 2015 Customer: Radio Systems Model: SDT00-12721 Page 4 of 7 Figure 4. EUT Side 2 US Tech Test Report: FCC Part 15 Certification/ RSS 210 FCC ID: KE3-3003061 IC: 2721A-3003061 Test Report Number: 15-0033 Issue Date: February 19, 2015 Customer: Radio Systems Model: SDT00-12721 Page 5 of 7 Figure 5. EUT Side 3 US Tech Test Report: FCC Part 15 Certification/ RSS 210 FCC ID: KE3-3003061 IC: 2721A-3003061 Test Report Number: 15-0033 Issue Date: February 19, 2015 Customer: Radio Systems Model: SDT00-12721 Page 6 of 7 Figure 6. EUT Side 4 US Tech Test Report: FCC Part 15 Certification/ RSS 210 FCC ID: KE3-3003061 IC: 2721A-3003061 Test Report Number: 15-0033 Issue Date: February 19, 2015 Customer: Radio Systems Model: SDT00-12721 Page 7 of 7 Figure 7. EUT Bottom

US Tech Test Report: FCC Part 15 Certification/ RSS 210 FCC ID: KE3-3003061 IC: 2721A-3003061 Test Report Number: 15-0033 Issue Date: February 19, 2015 Customer: Radio Systems Model: SDT00-12721 Page 1 of 1 Sample Label Location Figure 1. EUT Bottom MOD SDT00-12721

US Tech Test Report: FCC Part 15 Certification/ RSS 210 FCC ID: KE3-3003061 IC: 2721A-3003061 Test Report Number: 15-0033 Issue Date: February 19, 2015 Customer: Radio Systems Model: SDT00-12721 Page 1 of 3 INTERNAL PHOTOGRAPHS Figure 1. EUT with Cover Removed US Tech Test Report: FCC Part 15 Certification/ RSS 210 FCC ID: KE3-3003061 IC: 2721A-3003061 Test Report Number: 15-0033 Issue Date: February 19, 2015 Customer: Radio Systems Model: SDT00-12721 Page 2 of 3 Figure 2. PCB Component Side US Tech Test Report: FCC Part 15 Certification/ RSS 210 FCC ID: KE3-3003061 IC: 2721A-3003061 Test Report Number: 15-0033 Issue Date: February 19, 2015 Customer: Radio Systems Model: SDT00-12721 Page 3 of 3 Figure 3. PCB Solder Side

Page 1 of 22 Application For Title 47 USC Part 2, Subpart J, Paragraph 2.907 Equipment Authorization of Certification for an Intentional Radiator per Part 15, Subpart C, Paragraphs 15.207 and 15.209 And Industry Canada, Radio Standards Specifications: RSS Gen Issue 4 and RSS-210 Issue 8 For the Radio Systems Model: SDT00-12721 FCC ID: KE3-3003061 IC: 2721A-3003061 UST Project: 15-0033 Issue Date: February 19, 2015 Total Pages in This Report: 22 3505 Francis Circle Alpharetta, GA 30004 PH: 770-740-0717 Fax: 770-740-1508 www.ustech-lab.com Page 2 of 22 I certify that I am authorized to sign for the Test Agency and that all of the statements in this report and in the Exhibits attached hereto are true and correct to the best of my knowledge and belief: US TECH (Agent Responsible For Test): By: George Yang Name:_______________________ Title: Laboratory Manager Date February 19, 2015 This report shall not be reproduced except in full. This report may be copied in part only with the prior written approval of US Tech. The results contained in this report are subject to the adequacy and representative character of the sample provided. This report must not be used to claim product certification, approval, or endorsement by NVLAP, NIST or any agency of the Federal Government. 3505 Francis Circle Alpharetta, GA 30004 PH: 770-740-0717 Fax: 770-740-1508 www.ustech-lab.com US Tech Test Report: FCC Part 15 Certification/ RSS 210 FCC ID: KE3-3003061 IC: 2721A-3003061 Test Report Number: 15-0033 Issue Date: February 19, 2015 Customer: Radio Systems Model: SDT00-12721 Page 3 of 22 MEASUREMENT TECHNICAL REPORT COMPANY NAME: Radio Systems MODEL: SDT00-12721 FCC ID: KE3-3003061 IC: 2721A-3003061 DATE: February 19, 2015 This report concerns (check one): Original grant X Class II change Equipment type: 7.37 kHz or 10.65 kHz Transmitter Module Deferred grant requested per 47 CFR 0.457(d)(1)(ii)? yes_____ No X If yes, defer until: ______N/A___________ date agrees to notify the Commission by N/A date of the intended date of announcement of the product so that the grant can be issued on that date. Report prepared by: US Tech 3505 Francis Circle Alpharetta, GA 30004 Phone Number: (770) 740-0717 Fax Number: (770) 740-1508 US Tech Test Report: FCC Part 15 Certification/ RSS 210 FCC ID: KE3-3003061 IC: 2721A-3003061 Test Report Number: 15-0033 Issue Date: February 19, 2015 Customer: Radio Systems Model: SDT00-12721 Page 4 of 22 Table of Contents Paragraph Title Page 1 General Information .......................................................................................... 6 1.1 Purpose of this Report .................................................................................. 6 1.2 Characterization of Test Sample ................................................................... 6 1.3 Product Description ...................................................................................... 6 1.4 Configuration of Tested System .................................................................... 6 1.5 Test Facility ................................................................................................... 7 2 Tests and Measurements ................................................................................. 9 2.1 Test Equipment ............................................................................................. 9 2.2 Modifications to EUT Hardware .................................................................. 10 2.3 Number of Measurements for Intentional Radiators (15.31(m)) .................. 10 2.4 Frequency Range of Radiated Measurements (Part 15.33)........................ 10 2.4.1 Intentional Radiator ................................................................................. 10 2.4.2 Unintentional Radiator ............................................................................ 11 2.5 Measurement Detector Function and Bandwidth (CFR 15.35) ................... 11 2.5.1 Detector Function and Associated Bandwidth ........................................ 11 2.5.2 Corresponding Peak and Average Requirements ................................... 11 2.5.3 Pulsed Transmitter Averaging ................................................................. 11 2.6 EUT Antenna Requirements (CFR 15.203) ................................................ 12 2.7 Restricted Bands of Operation (Part 15.205) .............................................. 12 2.8 Intentional Radiator, Power Line Conducted Emissions (CFR 15.207) ....... 12 2.9 Intentional Radiator, Radiated Emissions (CFR 15.209, (IC RSS 210)) ..... 13 2.10 99% Occupied Bandwidth (IC RSS 210, A8.1) ........................................... 15 2.11 Unintentional/Intentional Radiator, Power line Emissions (CFR 15.107 and 15.207) ................................................................................................................. 17 2.12 Unintentional/Intentional Radiator, Radiated Emissions (CFR 15.109 and 15.209) ................................................................................................................. 19 2.13 Measurement Uncertainty .......................................................................... 22 2.13.1 Conducted Emissions Measurement Uncertainty ................................. 22 2.13.2 Radiated Emissions Measurement Uncertainty .................................... 22 US Tech Test Report: FCC Part 15 Certification/ RSS 210 FCC ID: KE3-3003061 IC: 2721A-3003061 Test Report Number: 15-0033 Issue Date: February 19, 2015 Customer: Radio Systems Model: SDT00-12721 Page 5 of 22 List of Figures Figures Title Page Figure 1. Test Configuration ...................................................................................... 8 Figure 2. 20 dB & 99% Bandwidth ........................................................................... 16 List of Tables Table Title Page Table 1. EUT and Peripherals .................................................................................... 8 Tab…

Text truncated - open the document above for the full version.

US Tech Test Report: FCC Part 15 Certification/ RSS 210 FCC ID: KE3-3003061 IC: 2721A-3003061 Test Report Number: 15-0033 Issue Date: February 19, 2015 Customer: Radio Systems Model: SDT00-12721 Page 1 of 5 TEST CONFIGURATION PHOTOGRAPHS Figure 1. Radiated Emissions Test Setup US Tech Test Report: FCC Part 15 Certification/ RSS 210 FCC ID: KE3-3003061 IC: 2721A-3003061 Test Report Number: 15-0033 Issue Date: February 19, 2015 Customer: Radio Systems Model: SDT00-12721 Page 2 of 5 Figure 2. Radiated Emissions Test Setup (below 30 MHz) US Tech Test Report: FCC Part 15 Certification/ RSS 210 FCC ID: KE3-3003061 IC: 2721A-3003061 Test Report Number: 15-0033 Issue Date: February 19, 2015 Customer: Radio Systems Model: SDT00-12721 Page 3 of 5 Figure 3. Radiated Emissions Test Setup (30 - 200 MHz) US Tech Test Report: FCC Part 15 Certification/ RSS 210 FCC ID: KE3-3003061 IC: 2721A-3003061 Test Report Number: 15-0033 Issue Date: February 19, 2015 Customer: Radio Systems Model: SDT00-12721 Page 4 of 5 Figure 4. Radiated Emissions Test Setup (200 Mhz - 1 GHz) US Tech Test Report: FCC Part 15 Certification/ RSS 210 FCC ID: KE3-3003061 IC: 2721A-3003061 Test Report Number: 15-0033 Issue Date: February 19, 2015 Customer: Radio Systems Model: SDT00-12721 Page 5 of 5 Figure 5. Power Line Conducted Emissions Test Setup