KE3-300996TRANSMITTER

800 Series Transmitters Owner’s Manual www.invisiblefence.com www.invisiblefence.com 2 www.invisiblefence.com Important Precautions • Invisible Fence ® Brand pet containment systems have contained over two million pets. However, there are some precautions you should take. • Read and retain manuals: Read the entire Owner’s Manual before using your new Invisible Fence Brand pet containment system. • Adhere to all warnings and cautions contained in any Invisible Fence Brand manual. WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury. CAUTION used without the safety alert symbol, indicates a hazardous situation which, if not avoided, could result in harm to your pet. NOTICE is used to address safe use practices not related to personal injury. • Replacing the battery backup with a battery not specifically approved by Invisible Fence Brand may cause fire or explosion. Refer all service to your Invisible Fence Brand Dealer only. • Not every pet can be trained to avoid the established boundary. Sometimes even a properly trained pet may cross the boundary. Therefore, Invisible Fence ® , Inc., as well as Invisible Fence ® Distributors and Dealers, cannot guarantee the system will, in all cases, keep a customer’s pet within the established boundary. Accordingly, if a customer has reason to believe that their pet may pose a danger to others, or harm itself, the customer should not rely solely upon the Invisible Fence Brand pet containment system to keep the pet from crossing the boundary. • Do not install, connect, or remove your system during a lightning storm. If the storm is close enough for you to hear thunder, it is close enough to create hazardous surges. • Read and follow the important instructions on how to avoid pressure necrosis in your Invisible Fence Brand Computer Collar ® manual. • Train your pet according to the instructions in the Invisible Fence Brand training manuals. Complete all steps before allowing your pet to run free. Do not become overly confident if your pet has become conditioned to the Invisible Fence Brand pet containment system sooner than expected. • Your Invisible Fence Brand Dealer has professionally installed your pet containment system and ensured it is working properly. You will want to perform periodic maintenance checks to make sure the system is properly functioning for your pet’s safe containment. • Check the Invisible Fence Brand transmitter periodically to make sure it is operating properly. To do this, simply bring the Computer Collar to the edge of the containment field to verify function. • The transmitter has visual and audible signals to warn of a system malfunction. The transmitter should be installed where such signals may be easily seen and heard. If the transmitter is installed by the customer in an enclosed box, or in a place not readily accessible to the customer, the customer will not benefit from the system’s warning functions, for which Invisible Fence, Inc., as well as Invisible Fence Distributors and Dealers, assume no responsibility. • Do not attempt to service any Invisible Fence Brand equipment. Refer all service to your authorized Invisible Fence Brand Dealer. Only your authorized Invisible Fence Brand Dealer should make adjustments to your pet containment system. • All Invisible Fence Brand pet containment systems are designed for domesticated animal use only. Never attempt to use this product for any purpose not specifically described in this manual. • Use care when mowing, aerating, or trimming your lawn so as not to cut the loop wire. • If you have any questions about any aspect of your Invisible Fence Brand pet containment system, call your Invisible Fence Brand Dealer immediately. WARNING CAUTION NOTICE WARNING CAUTION NOTICE www.invisiblefence.com 3 Congratulations on your purchase of the world’s premier pet containment solution, the Invisible Fence ® Brand. When professionally installed, the Invisible Fence Brand pet containment system is backed with a one- year, money-back performance guarantee. The support of your Invisible Fence Brand Dealer gives you peace of mind that your pet remains Safe At Home ® . Refer to the back of your sales contract for complete details. An 800 Series transmitter may have been used to replace your 700 Series transmitter under warranty. Contact your local Invisible Fence Brand professional to discuss the features and benefits of updating the remainder of your 700 Series equipment to the 800 Series platform. ___________________________________________________ Table of Contents Components .................................................................................................................................................4 How the Systems Works .................................................................................................................................4 Transmitter Status Indicators .........................................................................................................................5 Periodic Maintenance Check .........................................................................................................................6 Monthly Signal Field Width Test ....................................................................................................................6 Troubleshooting Guide ..................................................................................................................................6 Battery Disposal ............................................................................................................................................7 Compliance ..................................................................................................................................................8 ___________________________________________________ 4 www.invisiblefence.com Components Transmitter ICT 801, 802 or 810 AC Adapter Owner’s Manual www.invisiblefence.c…

Text truncated - open the document above for the full version.

Radio Systems Corporation Aug. 23, 2011 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: KE3-300996. Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Exhibit Type File Name Block Diagram KE3-300996_BlcokDiagram.pdf Schematics KE3-300996_SchematicDiagram.pdf Circuit Description KE3-300996_CircuitDescription.pdf The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, we are aware that the exhibits listed above have publicly available since the date the grant was issued. Sincerely, Radio Systems Corporation ---------------------------------------------------------- Clif Brick Product Safety and Regulatory Manager

Radio Systems Corporation Letter of Authorization FCC ID: KE3-300996 Jul. 18, 2011 Federal Communications Commission Authorization and Evaluation Divisoin 7435 Oakland Mills Road Columbia, MD 21046 To Whom It’s My Concern: We, the undersigned,hereby Authorize Anbotek Compliance Laboratory Limited (Daniel Zhu) on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Anbotek Compliance Laboratory Limited (Daniel Zhu). On our behalf shall have the same effect as acts of our own. This Authorization expires on Sept. 18, 2011 This is to advise that we are in full compliance with the Anti-Drug Abuse Act. We, Radio Systems Corporation, are not subject to a denial of federal benefits pursuant to section 5301 of the Anti-Drug Abuse Act of 1988.21 USC835a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely, Clif Brick Product Safety and Regulatory Manager

FCC ID: KE3-300996 Page 18 o f 21 Anbotek Compliance Laboratory Limited Report No. 201107721F APPENDIX I (EXTERNAL PHOTOS) Figure 1 The EUT-Overall View Figure 2 The EUT- Front View FCC ID: KE3-300996 Page 19 o f 21 Anbotek Compliance Laboratory Limited Report No. 201107721F Figure 3 The EUT- Back View

The proposed Label Location on EUT Proposed FCC ID Label Location Proposed Label Location on EUT The EUT-Back View/Proposed FCC ID Label Location

FCC ID: KE3-300996 Page 20 o f 21 Anbotek Compliance Laboratory Limited Report No. 201107721F APPENDIX II(INTERNALPHOTOS) Figure 4 The EUT-Inside View Figure 5 PCB of the EUT-Front View FCC ID: KE3-300996 Page 21 o f 21 Anbotek Compliance Laboratory Limited Report No. 201107721F Figure 6 PCB of the EUT-Back View

FCC ID: KE3-300996 Page 1 o f 21 Anbotek Compliance Laboratory Limited Report No. 201107721F FCC TEST REPORT for Radio Systems Corporation Transmitter Model No.: ICT 801 Prepared for : Radio Systems Corporation Address : 10427 Electric Ave., Knoxville, TN 37932 USA Prepared By : Anbotek Compliance Laboratory Limited Address : 1/F, 1/Build, SEC Industrial Park, No. 4 Qianhai Road, Nanshan District, Shenzhen, 518054, China Tel: (86) 755-26014771 Fax: (86) 755-26014772 Report Number : 201107721F Date of Test : Jul. 19~25, 2011 Date of Report : Aug. 20, 2011 FCC ID: KE3-300996 Page 2 o f 21 Anbotek Compliance Laboratory Limited Report No. 201107721F TABLE OF CHOnTENTS Description Page Test Report Verification 1. GENERAL INFORMATION ............................................................................................................... 4 1.1. Description of Device (EUT) ..........................................................................................................................4 1.2. Description of Test Facility.............................................................................................................................5 1.3. Measurement Uncertainty ...............................................................................................................................5 2. MEASURING DEVICE AND TEST EQUIPMENT .......................................................................... 6 3. TEST PROCEDURE ............................................................................................................................. 7 4. POWER LINE CONDUCTED MEASUREMENT ............................................................................ 8 4.1. Block Diagram of Test Setup ..........................................................................................................................8 4.2. Power Line Conducted Emission Measurement Limits (FCC Part 15 15.207)...............................................8 4.3. Configuration of EUT on Measurement..........................................................................................................8 4.4. Operating Condition of EUT...........................................................................................................................8 4.5. Test Procedure.................................................................................................................................................9 4.6. Power Line Conducted Emission Measurement Results.................................................................................9 5. RADIATED EMISSION MEASUREMENT..................................................................................... 12 5.1. Radiated Emission Limits .............................................................................................................................12 5.2. Test Procedure...............................................................................................................................................12 5.3. Test Setup......................................................................................................................................................13 5.4. Test Results (Below 30MHz) ........................................................................................................................14 5.5. Test Results (Between 30-1000MHz) ...........................................................................................................14 6. PHOTOGRAPH ................................................................................................................................... 17 6.1. Photo of Power Line Conducted Emission Test............................................................................................17 6.2. Photo of Radiated Emission Test ..................................................................................................................17 APPENDIX I (External Photos) (2 Pages) APPENDIX II (Internal Photos) (2 Pages) FCC ID: KE3-300996 Page 3 o f 21 Anbotek Compliance Laboratory Limited Report No. 201107721F TEST REPORT VERIFICATIOn Applicant : Radio Systems Corporation Manufacturer : Radio Systems Corporation EUT : Transmitter Model No. : ICT 801 Trade Mark : Invisible Fence Brand Measurement Procedure Used: FCC Rules and Regulations Part 15 Subpart C 15.207&15.209-2010 & FCC / ANSI C63.4-2009 The device described above is tested by Anbotek Compliance Laboratory Limited To determine the maximum emission levels emanating from the device. The maximum emission levels are compared to the FCC Part 15 Subpart C limits both radiated and conducted emissions. The measurement results are contained in this test report and Anbotek Compliance Laboratory Limited Is assumed full responsibility for the accuracy and completeness of these measurements. Also, this report shows that the Equipment Under Test (EUT) is to be technically compliant with the FCC requirements. This report applies to above tested sample only. This report shall not be reproduced in part without written approval of Anbotek Compliance Laboratory Limited Date of Test : Jul. 19~25, 2011 Prepared by : (Engineer/ Heise Chen) Reviewer : (Project Manager/ Coco Xiang) Approved & Authorized Signer : (Manager/ Henry Yang) FCC ID: KE3-300996 Page 4 o f 21 Anbotek Compliance Laboratory Limited Report No. 201107721F 1. GENERAL INFORMATION 1.1. Description of Device (EUT) Description : Transmitter Model Number : ICT 801 Test Power Supply : 120V~, 60Hz for Adapter Adapter : Model No.: KSAS0241900100HU Input: 100-240V~, 50/60Hz, 0.6A Output: 19V 1.0A CE, FCC, UL Frequency : 7.5KHz or 10.7KHz Applicant : Radio Systems Corporation Address : 10427 Electric Ave., Knoxville, TN 37932 USA Manufacturer : Radio Systems Corporation Address : 10427 Electric Ave., Knoxville, TN 37932 USA Date of Sample received : Jul. 18, 2011 Date of Test : Jul. 19~25, 2011 FCC ID: KE3-300996 Page 5 o f 21 Anbotek Compliance Laborator…

Text truncated - open the document above for the full version.

FCC ID: KE3-300996 Page 17 o f 21 Anbotek Compliance Laboratory Limited Report No. 201107721F 6. Photograph 6.1. Photo of Power Line Conducted Emission Test 6.2. Photo of Radiated Emission Test