KG6M170T17" LCD Monitor

M170T User Manual 17” LCD TV w/ PC Input CONTENTS General Information Key Features FCC Information How to contact Pixstorm Customer Service User Warnings Warranty Information General-Safety Precautions Installation Package Contents Control Descriptions Connecting to External Devices Adjusting the tilt base Basic Operation On Screen Display Menu & Function Table Pow er-Management System Preset Timing Modes Specifications Trouble shooting Registering your Pixstorm Product Copyright S t atement General Information Thank you for purchasing out 17” Flat-screen TFT LCD Monitor. It is a high performance, 17 inch analog signal input, color TFT LCD (Liquid Crystal Display) monitor. The LCD employs the latest state-of-the-art flat panel display technology providing a wider viewing angle, higher contrast ratio and greater color accuracy. Compatible with IBM and compatib le systems, this monitor is designed to operate under a multitude of hardware platforms and video standards VGA to 1280 x 1024 non-interlaced. Its multiscan function automatically adjusts the monitor to the scanning frequency of your video card. Its non-interlaced and higher refreshing rate offers flicker-free image, which reduces eye-strain and fatigue so that you can work in front of the screen longer. The OSD (on screen display) control system, which adopt the digital controls greatly enhances and expands your ability to control your display through adjusting the screen settings. The adjustable desk allows you to adjust the monitor to your preferred angle of vision. This outside adapter for led monitor also supports universal power supply, allowing you to use the monitor anywhere in the world. 1. Key Features 17-inch TFT LCD with anti-glare treatment 1280 x 1024 (SXGA) Optimal Resolution High contrast ratio with a sharp, crisp image Wide 160 ° viewing angle On-Screen Display (OSD) user controls Standard 15 Pin D-Sub VGA input Universal power supply for outside adapter Super-thin and slim design Built-in stereo speakers with volume control Standard S-Video input Full TV Capability 2. FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against radio frequency interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause interference to radio communications. However, there is no guarantee that interference will not occur in particular installation. If this equipment does cause interference to radio or television reception (this can be determined by turning the equipment off and on), the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from which the receiver is connected to. Consult the dealer or an experienced radio/television technician for help. 3. Contacting Pixstorm Customer Service If you find that service is needed on any of your Pixstorm products, call us at 1-800-PRENSTY (Monday through Friday: 10AM- 6PM P.S.T.), visit the Pixstorm website http://www.pixstorm.com or email us at [email protected] . If you contact us by email we will respond within 24-48 hours. Before contacting us please be prepared with the following data: • Name and model number of the Product • Serial Number of the Product • O/S and Processor you use • Detailed Description of the problem you are experiencing 4. User Warnings To assure continued FCC compliance, please use a grounded power supply cord and the provided shielded video interface cable with bonded ferrite cores. If a BNC cable is going to be used, use only a shielded BNC (5) cable. Also, The Federal Communications Commission warns the user that any unauthorized changes or modifications to the unit if not expressly approved by the party responsible for compliance could void the user's authority of operating the equipment. 5. Warranty Information Applicable to all Pixstorm LCD TVs Two-Year limited warranty for United States, Canada and Mexico This limited warranty applies in the United States, Canada and Mexico for all monitor products manufactured by Godwing Electronics Company Ltd. (Pixst orm) and distributed by PRENS International Trading Inc. under the Pixstorm brand name. This limited warranty extends to the original purchaser or any person receiving this product as a gift from the original purchaser only and is not transferable. Please cont act Pixstorm or your authorized Pixstorm reseller for all questions regarding this limited warranty. Terms of the warranty Pixstorm warrants the product you have purchased from Pixstorm or from an authorized Pixstorm reseller against defects in materials or workmanship under normal usage conditions for two calendar years. This limited warranty commences on the date of purchase and entitles you to two-year parts, excluding expendable parts, and a two-year repair labor warranty. Products sold and used for commercial applications have a limited ninety (90) day warranty for all parts and labor. Your sales receipt, showing the date of purchase is your proof of purchase date. During the warranty period, Pixstorm will repair or replace defective parts with new or, at Pixstorm's option, serviceable used parts that are equivalent to new parts in performance. All exchanged parts and products replaced under this warranty will become the property of Pixstorm. For products (a) sold and used for commercial applications (b) sold outside of the continental United States, warranty service is obtained by bringing or shipping your product to an authorized Pixstorm service provider. This warranty does not cover shipping charges, risk of loss during shipment, export taxes, custo…

Text truncated - open the document above for the full version.

SDA POWER CN800 DC12V CN202 AUDIO CONNECTOR AUDIO SIGNAL SDA U_9 LVDS LVDS OUTPUTTTLDATA IN KEYPAD KEY KEY SDA SPEAKER AUDIO IN 11 122 A4 11Friday, December 20, 2002 Title SizeDocument NumberRev Date:Sheetof ALIM6759 MCU SCL SDA IO IO IO CN100 VGA CONNECTOR VGA SIGNAL SAA7114 VEDIO DECODE YUV OUTPUT AI1 AI2 AI3SDA SCL CN101 DVI CONNECTOR DVI SIGNAL SCL CN300 S-VEDIO CONNECTOR S-VEDIO TDA7440 AUDIO CONTROLLER AI1 AI2 AUDIO OUT SDA SCL 5020 MAIN CHIP ANALOG INPUT DVI INPUT YUV INPUT GPIO DATA OUTPUT SCL SDA GPIO SCLSCL U_10 LCD PANEL LVDS IN BLANKLIGHT IN FRONT CONNECTOR AUDIO LED IR AUDIO OUT INVERT CONTROLHV OUT TA8216 POWER AMP AUDIO OUT AUDIO IN TUNER CONNECTOR CVBSI SIGNAL AF CN301 VEDIO CONNECTOR VEDIO SIGNAL SDA SCL O

From: Helen Zhao Sent: Thursday, March 13, 2003 5:29 PM To: Mike Kuo Subject: RE: SHENZHEN GODWING ELECTRONIC CO.,LTD, FCC ID:KG6M170T, AN02T2468 Hello Mike, Regarding Q1: Attached is modification letter for 17" lcd monitor of GODWING. Please review. Tahnk you! Helen -----Original Message----- From: Mike Kuo Sent: Wednesday, March 12, 2003 5:07 PM To: Helen Zhao Subject: FW: SHENZHEN GODWING ELECTRONIC CO.,LTD, FCC ID:KG6M170T, AN02T2468 -----Original Message----- From: CERTADM Sent: Wednesday, March 12, 2003 5:07 PM To: '[email protected]' Subject: SHENZHEN GODWING ELECTRONIC CO.,LTD, FCC ID:KG6M170T, AN02T2468 Notice_content ------------- Question #1: Please provide a modification report to list all the modification made on the device and signed by the applicant to acknowledge that all modifications will be incorporated into each unit sold in the U.S.. Best Regards Mike Kuo The items indicated above must be submitted before processing can continue on the above referenced application. Failure to provide the requested information within 60 days of the original e-mail date may result in application dismissal and forfeiture of the filing fee. Also, please note that partial responses increase processing time and should not be submitted. Any questions about the content of this correspondence should be directed to the e-mail address listed below the name of the sender.

MODIFIABLE VERIFICATION Manufacturer Name SHENZHEN GODWING ELECTRONICS CO., LTD. Model Designation / Trade name M170T/PIXSTORM Contact Person LIZHI Test date 2002.11.12 Engineer Avin Test Site COMPLIANCE ENGINEERING SERVICES (CHINA) Finish date 2002.11.29 Modifiable project 1.Two cables are shielded and contact case. IDIOGRAPH OF CLIENT IDIOGRAPH OF ENGINEER 2. Digital cable is shielded and contact case. 3.Power cable is shielded and contact cast. 4. Paste electric cotton on the position where shielded system contacting. 6.Cable of keystoke is shielded and contact case. 7. All GND of PCB are joined. 8.R102,R103,R104,R106,R107,R111 all change to120ohm bead. 9. The ground pin of POWERVGADVIAVS-VIDEO and one copper spring to case. 10.Paste electric cotton in TV portAV port and AUDIO IN port.

Model: M170T POWER RATING DC12V, 3.0A LISTED UL 1950 1Z55 E158020 CAUTION RISK OF ELECTRIC SHOCK’ DO NOT OPEN Godwing MADE IN CHINA FCC ID: KG6M170T THIS DEVICE COMPLIES WITH PART 15 OR THE FCC RULES. Operation IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1)THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE. AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION WARNING TO PREVENT FIRE OR SHOCK HAZAROS DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE ALSO DO NOT USE THIS UNIT’S POLARIZED PLUG WHIT AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED REFRAIN FROM OPENING THE CABINET AS TMERE ARE MION VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO Quallfied SERVICE PERSONNEL.

Report Number: SZ0211011 November 29, 2002 Page 1 of 25 Rev. 00 FCC CLASS B COMPLIANCE REPORT (DoC) for Electromagnetic Emissions of LCD MONITOR Tra d e N a m e : PIXSTORM Model Number : M170T Serial Number : N/A Report Number : SZ0211011 Date : November 29, 2002 Prepared for : SHENZHEN GODWING ELECTRONICS CO., LTD 2/F, 706 BLDG, PENGJI INDUSTRIAL PARK, LIANTANG, SHENZHEN, CHINA Prepared by : COMPLIANCE ENGINEERING SERVICES (CHINA) d.b.a. COMPLIANCE ENGINEERING SERVICES (CHINA) NO. 6 JINAO INDUSTRIAL PARK, NO.35 JUKENG ROAD, DASHUIKENG VILLAGE, GUANLAN TOWN, BAOAN DISTRICT, SHENZHEN, CHINA TEL: 86-755-28055000 FAX: 86-755-28055221 LAB CODE: 200577-0 LAB CODE: 200577-0Report Number: SZ0211011 November 29, 2002 Page 2 Rev. 00 LAB CODE: 200577-0 TABLE OF CONTENTS DESCRIPTION PAGE VERIFICATION OF COMPLIANCE 3 SYSTEM DESCRIPTION 4 PRODUCT INFORMATION 5 SUPPORT EQUIPMENT 6 MEASUREMENT PROCEDURE & LIMIT (LINE CONDUCTED EMISSION TEST) 7 MEASUREMENT PROCEDURE & LIMIT (RADIATED EMISSION TEST) 10 SUMMARY DATA 13 TEST FACILITY 16 TEST EQUIPMENT LIST 17 BLOCK DIAGRAM OF TEST SETUP 18 APPENDIX 1 PHOTOGRAPHS OF TEST SETUP (TEST SETUP OF LINE CONDUCTED EMISSION ) 19 APPENDIX 2 PHOTOGRAPHS OF TEST SETUP (TEST SETUP OF RADIATED EMISSION ) 21 APPENDIX 3 PHOTOGRAPHS OF EUT 23 Report Number: SZ0211011 November 29, 2002 Page 3 Rev. 00 LAB CODE: 200577-0 VERIFICATION OF COMPLIANCE Equipment Under Test: LCD MONITOR Tra d e N a m e: PIXSTORM Model Number: M170T Serial Number: N/A Applicant: SHENZHEN GODWING ELECTRONICS CO., LTD 2/F, 706 BLDG, PENGJI INDUSTRIAL PARK, LIANTANG, SHENZHEN, CHINA Manufacturer: SHENZHEN GODWING ELECTRONICS CO., LTD 2/F, 706 BLDG, PENGJI INDUSTRIAL PARK, LIANTANG, SHENZHEN, CHINA Type of Test: FCC Class B (DoC) Measurement Procedure: ANSI C63.4: 1992 File Number: SZ0211011 Date of test: November 17~28, 2002 Deviation: None Condition of Test Sample: Normal The above equipment was tested by Compliance Engineering Services (China) for compliance with the requirements set forth in the FCC Rules and Regulations Part 15, Subpart B and the measurement procedure according to ANSI C63.4. This said equipment in the configuration described in this report shows the maximum emission levels emanating from equipment are within the compliance requirements. The test results of this report relate only to the tested sample identified in this report. Responsible Party Avin Jam / Q. A. Manager Officer of the Responsible Party Report Number: SZ0211011 November 29, 2002 Page 4 Rev. 00 LAB CODE: 200577-0 SYSTEM DESCRIPTION EUT Test Program: 1. EMC test program was loaded and executed in Windows 2000 mode. 2. PC send Video signal to EUT and monitor is full of “H” patterns on the screen. 3. Test program sequentially exercised printer and modem, then sent “H” patterns to them individually. 4. DVD player send video, audio and s-video signal to EUT, and display on the screen. 5. Repeat 2 to 4. Test program is self-repeating throughout the test. Report Number: SZ0211011 November 29, 2002 Page 5 Rev. 00 LAB CODE: 200577-0 PRODUCT INFORMATION Housing Type: Plastic EUT Power Rating: AC 100~230V 50/60Hz Power during Test: 120VAC/60Hz changed to DC 12V by adaptor Adaptor Manufacture: FSP GROUP INC. Adaptor Model Mame: FSP048-1AD101C Power Cord Type: Unshielded, 1.8 m OSC/Clock Frequencies: Y1=24MHz, Y2==24.576MHz I/O Port of EUT: I/O Port Type Q’TY Tested with 1) Video in 1 1 2) Digital Video in 1 1 3) S-Video in 1 1 4) VGA in 1 1 5) TV in N/A N/A 6) Audio in 1 1 7) Audio out 1 1 8) Power 1 1 1) Difference between model numbers as below: Model Number Trade Name 1. M170T GODWING 2) Note: The trade name (list on this report) is different, (Please refer list as above) just for marketing only. Report Number: SZ0211011 November 29, 2002 Page 6 Rev. 00 LAB CODE: 200577-0 SUPPORT EQUIPMENT No. Equipment Model # Serial # FCC ID Trade NameData Cable Power Cord 1. PC PC1 N/A DoC N/A N/A Unshielded, 1.8m 2. Modem SUPERFAX6.0 9013593 IFAXDM1414 ACCEX Shielded, 1.8m Unshielded, 1.8m 3. Printer P310B N/A DoC EPSON Shielded, 1.8m Unshielded, 1.8m 4. Mouse MUS9J N 298792-007 EMJMUSJR COMPAQ Unshielded, 1.8m N/A 5. Keyboard E06333KUS221- C D8597-63001 DoC HP Unshielded, 1.8m N/A 6. DVD DVP-500 N/A DoC MALATA Unshielded, 1.8m Unshielded, 1.5m 7. Earphone N/A N/A DoC N/A Unshielded 1.2m N/A Note: All the above equipment/cables were placed in worse case positions to maximize emission signals during emission test. Grounding: Grounding was in accordance with the manufacturer’s requirements and conditions for the intended use. Report Number: SZ0211011 November 29, 2002 Page 7 Rev. 00 LAB CODE: 200577-0 SECTION 1 LINE CONDUCTED AND RADIATED EMISSION MEASUREMENT PROCEDURE (PRELIMINARY LINE CONDUCTED EMISSION TEST) 1) The equipment was set up as per the test configuration to simulate typical actual usage per the user’s manual. When the EUT is a tabletop system, a wooden table with a height of 0.8 meters is used and is placed on the ground plane as per EN55022 (see Test Facility for the dimensions of the ground plane used). When the EUT is a floor-standing equipment, it is placed on the ground plane which has a 3-12 mm non-conductive covering to insulate the EUT from the ground plane. 2) Support equipment, if needed, was placed as per EN55022. 3) All I/O cables were positioned to simulate typical actual usage as per EN55022. 4) The EUT received DC power from adaptor ,and adaptor received AC power through a Line Impedance Stabilization Network (LISN) which supplied power source and was grounded to the ground plane. 5) All support equipment received power from a second LISN supplying power of 120VAC/60Hz, if any. 6) The EUT test program was started. Emissions were measured on each current carrying line of the EUT using a spectrum Analyzer / Receiver connected to the LISN powering the EUT. The LISN has two monitoring points: Line 1 (Hot Side) and Line 2 (Neutral Side). Two scans were taken: one with Line 1 connected to Analyzer / Receiver and Line 2…

Text truncated - open the document above for the full version.

LINE CONDUCTED EMISSION TEST RADIATED EMISSION TEST (EN 55022)