KSNAD1321-10MWWireless Module

6 AD1321-10MW ZigBee Module Manual A&D Company,Limited 1, OUTLOOK This model is the general-purpose ZigBee module using the ISM band of the 2.4GHz zone at 10mW. It has an outside antenna terminal. You can control the module by an AT command and send data in a protocol of SPI (CSI) of the serial communication. 2, CAUTION & NOTICE FCC CAUTION z Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC NOTICE z FCC compliance statements are required to be included in the user manual of final system. z This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. z This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. z This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. z This equipment complies with FCC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65. This equipment has very low levels of RF energy that it is deemed to comply without testing of specific absorption ratio (SAR). z When you use this module in your products, Please specify as follow sentence to your product. [Contains Transmitter Module FCC ID:KSNAD1321-10MW] Or [Contains FCC ID:KSNAD1321-10MW]

A Picture of equipment AD1321 Top view Left side view Front view Right side viw Back view Bottom view with antenna

A Picture of inside AD1321-10MW Module  Front  Inside  Back

UL Japan, Inc. Head Office EMC Lab 4383-326 Asama-cho, Ise-shi, Mie 516-0021 Japan T:: +81.596.24.8999 / F:: +81.596.24.8124 / W:: ul.com/jp August 9, 2013 UL Japan, Inc. 4383-326 Asama-cho, Ise-shi, Mie 516-0021 Japan FCC ID: KSNAD1321-10MW To whom it may concern, We, UL Japan, Inc, hereby declare that Wireless Module, model: AD1321-10MW (FCC ID: KSNAD1321-10MW) of A&D Company Limited is exempt from RF exposure SAR evaluation as its output power meets the exclusion limits stated in FCC Part 2 §2.1093. KDB 447498D01(V05) has the following exclusion for portable devices: The 1g and 10g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ·[√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where •f(GHz) is the RF channel transmit frequency in GHz •Power and distance are rounded to the nearest mW and mm before calculation •The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. This device has f = 2.48 GHz and distance = 5 mm (minimum separation distance: 5mm was used in the calculation) and the maximum tune-up tolerance limit was 1.36mW* * Clause 6.3 Low transmission duty factor devices of KDB447498 D01 v05r01 was applied to this product due to its specification. Maximum tune-up tolerance limit = Conducted Output power (9.36dBm)*Antenna Gain (2.14dBi)*duty cycle correction factor (-10.19dB) So for this device: 1.36mW[maximum tune-up tolerance limit]/5mm[minimum separation distance]*√2.48 = 0.43 *This is less than 3.0 so no SAR is required. Thank you for your attention to this matter. Masanori Nishiyama Manager of Head Office EMC Lab. WiSE Japan UL Verification Service UL Japan, Inc.

Test report No. : 32CE0244-HO-01-B-R2 Page : 2 of 41 Issued date : August 5, 2013 Revised date : August 8, 2013 FCC ID : KSNAD1321-10MW UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 REVISION HISTORY Original Test Report No.: 32CE0244-HO-01-B Revision Test report No. Date Page revised Contents - (Original) 32CE0244-HO-01-B August 5, 2013- - 1 32CE0244-HO-01-B- R1 August 6, 2013P.9 Changed of Configuration and peripherals 1 32CE0244-HO-01-B- R1 August 6, 2013P.12 Correction of Test procedure description 1 32CE0244-HO-01-B- R1 August 6, 2013P.20, 23, 24, 27 Addition of Remark’s comment 2 32CE0244-HO-01-B- R2 August 8, 2013P.13 Addition of Page 13 (Duty cycle correction factor) 2 32CE0244-HO-01-B- R2 August 8, 2013P.14 Correction of *4) description Test report No. : 32CE0244-HO-01-B-R2 Page : 3 of 41 Issued date : August 5, 2013 Revised date : August 8, 2013 FCC ID : KSNAD1321-10MW UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 CONTENTS PAGE SECTION 1: Customer information ......................................................................................................... 4 SECTION 2: Equipment under test (E.U.T.) ........................................................................................... 4 SECTION 3: Test specification, procedures & results ............................................................................ 5 SECTION 4: Operation of E.U.T. during testing .................................................................................... 8 SECTION 5: Conducted Emission .......................................................................................................... 11 SECTION 6: Radiated Spurious Emission ............................................................................................ 12 SECTION 7: Antenna Terminal Conducted Tests ................................................................................ 14 APPENDIX 1: Data of EMI test .............................................................................................................. 15 Conducted Emission ......................................................................................................................... 15 6dB Bandwidth ................................................................................................................................. 19 Maximum Peak Output Power .......................................................................................................... 20 Average Output Power (Reference data for MPE)............................................................................ 20 Radiated Spurious Emission ............................................................................................................. 21 Conducted Spurious Emission .......................................................................................................... 30 Power Density ................................................................................................................................... 33 99%Occupied Bandwidth ................................................................................................................. 34 APPENDIX 2: Test instruments ............................................................................................................. 35 APPENDIX 3: Photographs of test setup ............................................................................................... 36 Conducted Emission ......................................................................................................................... 36 Radiated Spurious Emission ............................................................................................................. 38 Worst Case Position .......................................................................................................................... 40 Test report No. : 32CE0244-HO-01-B-R2 Page : 4 of 41 Issued date : August 5, 2013 Revised date : August 8, 2013 FCC ID : KSNAD1321-10MW UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 SECTION 1: Customer information Company Name : A&D Company Limited Address : 1-243 asahi Kitamoto-city Saitama-prefectiure, 364-8585 Japan Telephone Number : +81-48-593-1342 Facsimile Number : +81-48-593-1117 Contact Person : Onodera Fukushi SECTION 2: Equipment under test (E.U.T.) 2.1 Identification of E.U.T. Type of Equipment : Wireless Module Model No. : AD1321-10MW Serial No. : Refer to Section 4, Clause 4.2 Rating : DC3.0V Receipt Date of Sample : May 15, 2013 Country of Mass-production : Japan Condition of EUT : Production model Modification of EUT : No Modification by the test lab 2.2 Product Description This Module is using ZigBeePRO protocol, on general-purpose, in the ISM band of the 2.4GHz zone at 10mW. It has an external antenna terminal. It can be controlled by an AT command and sent data by SPI protocol which is serial communication as I/O. General Specification Clock frequency(ies) in the system : 32MHz Radio Specification Radio Type : Transceiver Frequency of Operation : 2405-2480MHz Modulation : Offset QPSK Power Supply : DC1.8V Type of Antenna : λ/4 whip Antenna 12mmPatch Antenna Antenna Gain : 2.14dBi (λ/4 whip Antenna) 2.00dBi (12mmPatch Antenna) Antenna connector type : U.FL Test report No. : 32CE0244-HO-01-B-R2 Page : 5 of 41 Issued date : August 5, 2013 Revised date : August 8, 2013 FCC ID : KSNAD1321-10MW UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 SECTION 3: Test specification, procedures & results 3.1 Test Specification Test Specification : FCC Part 15 Subpart C: 2013, final revised on June 11, 2013 and effecti…

Text truncated - open the document above for the full version.

Test report No. : 32CE0244-HO-01-B-R2 Page : 36 of 41 Issued date : August 5, 2013 Revised date : August 8, 2013 FCC ID : KSNAD1321-10MW UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 APPENDIX 3: Photographs of test setup Conducted Emission 12mmPatch Antenna Photo 1 Photo 2 Test report No. : 32CE0244-HO-01-B-R2 Page : 37 of 41 Issued date : August 5, 2013 Revised date : August 8, 2013 FCC ID : KSNAD1321-10MW UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 Conducted Emission Lambda /4 whip Antenna Photo 1 Photo 2 Test report No. : 32CE0244-HO-01-B-R2 Page : 38 of 41 Issued date : August 5, 2013 Revised date : August 8, 2013 FCC ID : KSNAD1321-10MW UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 Radiated Spurious Emission 12mmPatch Antenna Photo 1 Photo 2 Test report No. : 32CE0244-HO-01-B-R2 Page : 39 of 41 Issued date : August 5, 2013 Revised date : August 8, 2013 FCC ID : KSNAD1321-10MW UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 Radiated Spurious Emission Lambda /4 whip Antenna Photo 1 Photo 2 Test report No. : 32CE0244-HO-01-B-R2 Page : 40 of 41 Issued date : August 5, 2013 Revised date : August 8, 2013 FCC ID : KSNAD1321-10MW UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 Worst Case Position (Horizontal: X-axis/ Vertical:X-axis) X-axis Y-axis Z-axis Test report No. : 32CE0244-HO-01-B-R2 Page : 41 of 41 Issued date : August 5, 2013 Revised date : August 8, 2013 FCC ID : KSNAD1321-10MW UL Japan, Inc. Head Office EMC Lab. 4383-326 Asama-cho, Ise-shi, Mie-ken 516-0021 JAPAN Telephone : +81 596 24 8999 Facsimile : +81 596 24 8124 Worst Case Position 12mmPatch Antenna (Horizontal: X-axis/ Vertical:Z-axis) Lambda /4 whip Antenna (Horizontal: X-axis/ Vertical:Y-axis) 12mmPatch Antenna Lambda /4 whip antenna X-axis X-axis Y-axis Y-axis Z-axis Z-axis End of Report