L5C0790TXAPIR Sensor

Instructions Driveway Patrol Congratulations on purchasing the Driveway Patrol! Your set comes with a volume controlled Chime Unit and a Passive Infra-Red (PIR) Sensor. Both are battery operated. The Driveway Patrol system is simple to install and requires no wiring. Installing the Batteries: 1. The chime requires three C-size batteries (not included). To install the chime unit’s batteries, slide off compartment cover in direction of arrow and then install the receiver’s batteries. Be sure to observe correct polarity (+ and -) as marked inside the battery compartment. 2. The PIR sensor requires a 9V battery. To install the PIR sensor’s battery, unscrew the back cover of the sensor and insert the battery. Be sure to observe correct polarity (+ and -) as marked on the battery compartment. Operation: 1. Your Driveway Patrol Receiver Chime Unit has 3 settings (Hi or Lo Volume and Off). To switch the unit ON, select Hi or Lo Volume Settings. 2. Hang the PIR (Passive Infra Red) Sensor Unit at the entrance of your driveway (such as on a mailbox, on a tree or on a ground stake). You may also place the PIR Sensor on your garage, near the front entrance or rear door. Any movement nearby will transmit a signal to the Receiver Chime Unit triggering it to signal the chime. 3. Please ensure to place the PIR Sensor at least three feet high above the ground. 4. Receiver must be used indoors. Important Note: A) Whenever installing the PIR sensor the first time, the red LED on the PIR sensor will be on for about 60 seconds and the chime unit will sound for about 60 seconds in order to stabilize the units first. B) In some applications the motion detector may be too sensitive, resulting in false alerts. To remedy this situation, put masking tape or labels on each side of the sensor window. Start on the sides and add an equal length of masking tape or labels to each side. Test the detector and add more covering if needed. Keep the band as narrow as 1/8” wide or wider depending on individual situation. Some trial and error may be required to find the optimal width. Specifications: Transmission Range; 400 feet (open area) Receiver: 3 X 1.5V “C-size” battery, not included Transmission frequency; 434MHz Transmitter: 1 X 9V battery, not included PIR sensor range: 40 ̊ X 30 feet FCC Part 15 compliance Battery Caution: 1. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries. 2. Non-rechargeable batteries are not to be recharged. 3. Never mix old and new batteries. 4. Make sure batteries are inserted with correct polarity. 5. Exhausted or dead batteries are to be removed from the unit. 4 Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may case harmful interference to radio communications. However, there is no gurantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/ TV technician for help. Modifications not authorized by the manufacturer may void users authority to operate this device. ANSEN ELECTRONICS CO. 0784-5

PHOTOGRAPH OF THE PRODUCT FRONT VIEW OF THE PRODUCT REAR VIEW OF THE PRODUCT

BOTTOM VIEW OF TX FCC LABEL This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operations. FCC ID: L5C0790TXA MADE IN CHINA

香 港 標 準 及 檢 定 中 心 Hong Kong Standards and Testing Centre Date : 2004-12-02 TEST REPORT Page 1 of 20 No. : HM152757 This report shall not be reproduced unless with prior written approval from the Hong Kong Standards and Testing Centre. 香港新界大埔工業村大宏街10號 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] For full text of “Conditions of Issuance of Test Report”, please refer to overleaf or refer to the website of STC: www.hkstc.org (the section “Application and Quotation”). Applicant: Ansen Electronics Company Room 73-78, 2/F, Sino Industrial Plaza, 9 Kai Cheung Road, Kowloon Bay, Kowloon, Hong Kong Description of Samples: Model name: Driveway Patrol Model no.: 0790-1 Brand name: Ansen FCC ID: L5C0790TXA Date Samples Received: 2004-10-27 Date Tested: 2004-11-30 Investigation Requested: FCC Part 15 Subpart C Conclusions: The submitted product was deemed to have COMPLIED with the requirements of Federal Communications Commission [FCC] Rules and Regulations Part 15. The tests were performed in accordance with the standards described above and on Section 2.2 in this Test Report. Remarks: ---- K C Lee, EMC for Chief Executive 香 港 標 準 及 檢 定 中 心 Hong Kong Standards and Testing Centre Date : 2004-12-02 TEST REPORT Page 2 of 20 No. : HM152757 香港新界大埔工業村大宏街10號 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] For full text of “Conditions of Issuance of Test Report”, please refer to overleaf or refer to the website of STC: www.hkstc.org (the section “Application and Quotation”). CONTENT: Cover Page 1 of 20 Content Page 2-3 of 20 1.0 General Details 1.1 Test Laboratory Page 4 of 20 1.2 Applicant Details Page 4 of 20 Applicant HKSTC Code Number for Applicant Manufacturer 1.3 Equipment Under Test [EUT] Page 5 of 20 Description of EUT operation 1.4 Date of Order Page 5 of 20 1.5 Submitted Samples Page 5 of 20 1.6 Test Duration Page 5 of 20 1.7 Country of Origin Page 5 of 20 1.8 Additional Information of EUT Page 6 of 20 2.0 Technical Details 2.1 Investigations Requested Page 7 of 20 2.2 Test Standards and Results Summary Page 7 of 20 3.0 Test Results 3.1 Emission Page 8-12 of 20 3.2 Bandwidth Measurement Page 13-14 of 20 香 港 標 準 及 檢 定 中 心 Hong Kong Standards and Testing Centre Date : 2004-12-02 TEST REPORT Page 3 of 20 No. : HM152757 香港新界大埔工業村大宏街10號 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] For full text of “Conditions of Issuance of Test Report”, please refer to overleaf or refer to the website of STC: www.hkstc.org (the section “Application and Quotation”). Appendix A List of Measurement Equipment Page 15 of 20 Appendix B Duty Cycle Correction During 100 msec Page 16-17 of 20 Appendix C Periodic Operation Page 18 of 20 Appendix D Photographs Page 19-20 of 20 香 港 標 準 及 檢 定 中 心 Hong Kong Standards and Testing Centre Date : 2004-12-02 TEST REPORT Page 4 of 20 No. : HM152757 香港新界大埔工業村大宏街10號 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] For full text of “Conditions of Issuance of Test Report”, please refer to overleaf or refer to the website of STC: www.hkstc.org (the section “Application and Quotation”). 1.0 General Details 1.1 Test Laboratory The Hong Kong Standards and Testing Centre Ltd. EMC Laboratory 10 Dai Wang Street, Taipo Industrial Estate New Territories, Hong Kong Telephone: 852 2666 1888 Fax: 852 2664 4353 1.2 Applicant Details Applicant Ansen Electronics Company Room 73-78, 2/F, Sino Industrial Plaza, 9 Kai Cheung Road, Kowloon Bay, Kowloon, Hong Kong HKSTC Code Number for Applicant ANE001 Manufacturer Ansen Electronics Company Chen Tung Industrial Zone, Ning Tau Administrative District, Qiao Tau Zhen, Dongguan, Guangdong, China 香 港 標 準 及 檢 定 中 心 Hong Kong Standards and Testing Centre Date : 2004-12-02 TEST REPORT Page 5 of 20 No. : HM152757 香港新界大埔工業村大宏街10號 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] For full text of “Conditions of Issuance of Test Report”, please refer to overleaf or refer to the website of STC: www.hkstc.org (the section “Application and Quotation”). 1.3 Equipment Under Test [EUT] Description of Sample Product: Driveway Patrol Manufacturer: Ansen Electronics Company Brand Name: Ansen Model Number: 0790-1 Input Voltage: 9Vd.c (“6F22” size battery x 1) 1.3.1 Description of EUT Operation The Equipment Under Test (EUT) is an Ansen Electronics Company, Driveway Patrol. The EUT is to transmit RF signal while each button is being pressed, Modulation by Data Code type is pulse modulation. 1.4 Date of Order 2004-10-27 1.5 Submitted Sample(s): 6 Samples per model 1.6 Test Duration 2004-11-30 1.7 Country of Origin China 香 港 標 準 及 檢 定 中 心 Hong Kong Standards and Testing Centre Date : 2004-12-02 TEST REPORT Page 6 of 20 No. : HM152757 香港新界大埔工業村大宏街10號 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] For full text of “Conditions of Issuance of Test Report”, please refer to overleaf or refer to the website of STC: www.hkstc.org (the section “Application and Quotation”). 1.8 Additional Information of EUT Submitted Not Available User Manual Part List Circuit Diagram Printed Circuit Board [PCB] Layout Block diagram FCC ID Label 香 港 標 準 及 檢 定 中 心 Hong Kong Standards and Testing Centre Date : 2004-12-02 TEST REPORT Page 7 of 20 No. : HM152757 香港新界大埔工業村大宏街10號 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] For full text of “Conditions of Issuance of Test Report”, please refer to overleaf…

Text truncated - open the document above for the full version.

TEST SET UP PHOTOGRAPH OF THE PRODUCT MEASUREMENT OF RADIATED EMISSION TEST SET UP