L5CR087GTSoft Mood Light Bluetooth Speaker

Bluetooth Mono Speaker with Color Changing Light (Jazz) User Manual Play from a Bluetooth device Note: The effective operation range between the speaker and your Bluetooth device is approximately 10 meters (33 feet) line of sight maximum - Slide the Power [ON/OFF] switch to “ON” to turn on the speaker - The blue LED indicator which is located on the bottom left of the casing will flash - Activate the Bluetooth function on your Bluetooth device - Select “BT SPEAKER” on your Bluetooth device for pairing - When connected, the blue LED indicator stays steadily on - Start music play on your Bluetooth device - Adjust volume on your Bluetooth device or press the [+] or [-] button on the speaker - Press [Play/Pause] button on the speaker to play or pause music - Slide the Power [ON/OFF] switch to “OFF” when the speaker is not in use for power saving Play from an external device - Slide the Power [ON/OFF] switch to “ON” to turn on the speaker - Connect your speaker with an external device through a 3.5mm cable (not supplied) - Start music play on your device - Slide the Power [ON/OFF] switch to “OFF” when the speaker is not in use for power saving Color Changing RGB LED Light effect - Slide the Power [ON/OFF] switch to turn on the Speaker - Press [LIGHT] button repeatedly to toggle between below modes 1) Continuous color changing mode 2) Fixed color mode: While it is in color changing mode, wait until your desired color appears and press [LIGHT] button to freeze the color 3) Sound-to-Light mode : In fixed color mode, press [LIGHT] button once to switch to “Sound-to-light” mode and the top red light indicator will turn on. Start music play on your device, the color of the RGB LED light will change according to the beat of your music NOTE: - If the sound volume is too low, the RGB LED light may not turn on and this is normal. Turn the volume up and the RGB LED will light up. - If the speaker is not playing any music or sound, the RGB LED will turn off 4) Off mode Power Supply The speaker operates on built-in rechargeable battery To recharge the built-in battery, connect micro USB socket with PC through supplied USB cable Charging: Red LED indicator turns on Fully Charged: Red LED turns green when it is fully charged Low battery level: RED LED indicator flashes NOTE: Red/Green LED indicator is located on the bottom left of the speaker Specification Rated output power: 1.6W RMS DC Power input: USB: 5V, 500mA Bluetooth specification: V3.0 + EDR Supported Bluetooth Profiles: AVRCP, A2DP Range: maximum 10 meters (33 feet) line of sight Working temperature: 0C – 50C Troubleshooting No power: - Recharge your speaker No sound: - Adjust volume on your Bluetooth device or the speaker - Make sure that your Bluetooth device is connected with the speaker and they are within the effective operation range No RGB LED light: - Recharge your speaker - You may be in the color LED “OFF” mode. Press the [LIGHT] button to toggle the different color light mode according to the manual - If you are in the “Sound-to-Light” mode, try increase the volume level of your music until the color light appears Cautions: 1) Due to the used enclosure material, the device shall only be connected to a USB Interface of version 2.0 or higher. The connection to so called power USB is prohibited 2) Caution Risk of explosion if battery is replaced by an incorrect type. 3) Dispose of used batteries according to the instructions 4) Do not expose the device to an extremely high electromagnetic filed, this may impair the correct functioning of the device. 5) The normal function of the product may be disturbed by strong Electro-Magnetic Interference. If so, simply reset the product to resume normal operation by following the instruction manual. In case the function could not resume, please use the product in order location. FCC Statements This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct The interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. such modifications could void the user’s authority to operate this equipment.

Product Similarity Declaration FCC ID: L5CR087GT Date: Aug 30 2013 To Whom It May Concern, We , Ansen Electronics Company hereby declare that our ( Soft Mood Light Bluetooth Speaker ) Model Number: 06-ROQMOOD is same R087GT (PCB,Schemartic,Hardware erc), R087GT and 06-ROQMOOD are named differently due to marketing purposes. Please contact me if you have any question. Sincerely, Alvin Luo/ QE Manager Ansen Electronics Company Tel: (852)-2795-9473 Fax: (852)2751-6577 Web site:www.ansen.com.hk E-mail: [email protected]

Ansen Electronics Company FCC ID: L5CR087GT Date: Aug 30, 2013 To whom it may concern: We the undersigned, hereby authorize Shenzhen Huatongwei International Inspection Co., Ltd to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Shenzhen Huatongwei International Inspection Co., Ltd on our behalf shall have the same affect as acts of our own. This authorization shall expire 6 months from orignal data. If you have any questions regarding the authorization, please don’t hesitate to contact us. Sincerely, Alvin Luo/ QE Manager Ansen Electronics Company Tel: (852)-2795-9473 Fax: (852)2751-6577 Web site:www.ansen.com.hk E-mail: [email protected]

Ansen Electronics Company Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Gentlemen: This letter is to comply with Sections 0.457 and 0.459 pertaining to confidential material. Ansen Electronics Company would like the following documents regarding this submission for FCC ID: L5CR087GT to be kept confidential. 1. Block Diagram 2. Schematic 3. Theory of Operation The above material contains trade secrets or technical data, which would customarily be guarded from competitors. We do not want these documents to be accessible to the general public. Sincerely, Alvin Luo/ QE Manager Ansen Electronics Company Tel: (852)-2795-9473 Fax: (852)2751-6577 Web site:www.ansen.com.hk E-mail: [email protected]

External photos of the EUT

Internal photos of the EUT

RF EXPOSURE REPORT FCC Per 47 CFR 2.1093(d) Report Reference No. ..................... : FCC ID. ............................................ : TRE1308006402 R/C:32328 L5CR087GT Compiled by ( position+printed name+signature) .. : File administrators Jerome Luo Supervised by ( position+printed name+signature) .. : Test Engineer Yuchao Wang Approved by ( position+printed name+signature) .. : Manager Wenliang Li Date of issue ..................................... : Aug 27, 2013 Testing Laboratory Name .............. : Shenzhen Huatongwei International Inspection Co., Ltd Address ............................................. : Keji Nan No.12 Road, Hi-tech Park, Shenzhen, China Applicant’s name ............................ : Ansen Electronics Company Address ............................................. : Unit 1401B-1405A Telecom Tower,Wharf T&T Square, 123 Hoi Bun Road, Kwun Tong,Kowloon,Hong Kong Test specification: Standard ........................................... : FCC Per 47 CFR 2.1093(d) TRF Originator .................................. : Shenzhen Huatongwei International Inspection CO., Ltd Master TRF ....................................... : Dated 2006-06 Shenzhen Huatongwei International Inspection Co., Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen Huatongwei International Inspection Co., Ltd is acknowledged as copyright owner and source of the material. Shenzhen Huatongwei International Inspection Co., Ltd takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test item description .................... : Soft Mood Light Bluetooth Speaker Trade Mark ....................................... : / Manufacturer .................................. : Ansen Electronics Company Model/Type reference ....................... : R087GT Listed Models .................................. : 06-ROQMOOD Operation Frequency ........................ : From 2402MHz to 2480MHz Modulation Type ............................... : GFSK,π/4 DQPSK,8DPSK Rating ............................................... : DC 5.0V from USB Result ................................................ : Positive Report No.: TRE1308006402 Page 2 of 7 Issued:2013-08-27 RF EXPOSURE REPORT Test Report No. : TRE1308006402 Aug 27, 2013 ______________________________________________________________________________________________ Date of issue Equipment under Test : Soft Mood Light Bluetooth Speaker Model /Type : R087GT Listed Models : 06-ROQMOOD Applicant : Ansen Electronics Company Address : Unit 1401B-1405A Telecom Tower,Wharf T&T Square, 123 Hoi Bun Road, Kwun Tong,Kowloon,Hong Kong Manufacturer : Ansen Electronics Company Address : Chen Tung Industrial Zone,Ning Tau Administrative District,Qiao Tau Zhen,Dongguan,Guangdong The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Report No.: TRE1308006402 Page 3 of 7 Issued:2013-08-27 Contents 1. SUMMARY 4 1.1. EUT configuration 4 1.2. NOTE 4 2. TEST ENVIRONMENT 5 2.1. Address of the test laboratory 5 2.2. Environmental conditions 5 2.3. Statement of the measurement uncertainty 5 3. METHOD OF MEASUREMENT 5 3.1. Applicable Standard 5 3.2. Limit 6 3.3. RF Exposure 6 4. CONCLUSION 7 Report No.: TRE1308006402 Page 4 of 7 Issued:2013-08-27 1. SUMMARY 1.1. EUT configuration The following peripheral devices and interface cables were connected during the measurement: ● - supplied by the manufacturer ○ - supplied by the lab ○ Power Cable Length (m) : / Shield : / Detachable : / ○ Multimeter Manufacturer : / Model No. : / 1.2. NOTE 1. The EUT is a Soft Mood Light Bluetooth Speaker with Bluetooth function,The functions of the EUT listed as below: Test Standards Reference Report Bluetooth FCC Part 15 Subpart C TRE1308006401 RF Exposure FCC Per 47 CFR 2.1093(d) TRE1308006402 2. The frequency bands used in this EUT are listed as follows: Frequency Band(MHz) 2400-2483.5 5150-5350 5470-5725 5725-5850 EUT √ － － － Report No.: TRE1308006402 Page 5 of 7 Issued:2013-08-27 2. TEST ENVIRONMENT 2.1. Address of the test laboratory Shenzhen Huatongwei International Inspection Co., Ltd Keji Nan No.12 Road, Hi-tech Park, Shenzhen, China Phone: 86-755-26715686 Fax: 86-755-26748089 The sites are constructed in conformance with the requirements of ANSI C63.7, ANSI C63.4 (2009) and CISPR Publication 22. 2.2. Environmental conditions During the measurement the environmental conditions were within the listed ranges: Temperature: 15-35 ° C Humidity: 30-60 % Atmospheric pressure: 950-1050mbar 2.3. Statement of the measurement uncertainty The data and results referenced in this document are true and accurate. The reader is cautioned that there may be errors within the calibration limits of the equipment and facilities. The measurement uncertainty was calculated for all measurements listed in this test report acc. to TR-100028-01” Electromagnetic compatibility and Radio spectrum Matters (ERM);Uncertainties in the measurement of mobile radio equipment characteristics; Part 1” and TR-100028-02 “Electromagnetic compatibility and Radio spectrum Matters (ERM);Uncertainties in the measurement of mobile radio equipment characteristics; Part 2 “ and is documented in the Shenzhen Huatongwei International Inspection Co., Ltd quality system acc. to DIN EN ISO/IEC 17025. Furthermore, component and process variability of devices similar to that tested may result in additional deviation. The manufacturer has the sole responsibility of continued compliance of the device. Hereafter the best measurement capability for Shenzhen Huatongwei laboratory is reported: Test Items Measurement Uncertainty Notes Transmitter power conducted 0.57 dB (1) (1) This uncertainty represents an expanded uncertainty expressed at approximately the 95% c…

Text truncated - open the document above for the full version.

FCC PART 15 SUBPART C TEST REPORT FCC PART 15.247 Report Reference No. ..................... : FCC ID. ........................................... : TRE1308006401 R/C:32328 L5CR087GT Compiled by ( position+printed name+signature) .. : File administrators Jerome Luo Supervised by ( position+printed name+signature) .. : Test Engineer Yuchao Wang Approved by ( position+printed name+signature) .. : Manager Wenliang Li Date of issue ..................................... : Aug 27, 2013 Testing Laboratory Name .............. : Shenzhen Huatongwei International Inspection Co., Ltd Address ............................................ : Keji Nan No.12 Road, Hi-tech Park, Shenzhen, China Applicant’s name ............................ : Ansen Electronics Company Address ............................................ : Unit 1401B-1405A Telecom Tower,Wharf T&T Square, 123 Hoi Bun Road, Kwun Tong,Kowloon,Hong Kong Test specification: Standard ........................................... : FCC Part 15.247: Operation within the bands 902-928 MHz, 2400-2483.5 MHz and 5725-5850 MHz TRF Originator .................................. : Shenzhen Huatongwei International Inspection CO., Ltd Master TRF ....................................... : Dated 2006-06 Shenzhen Huatongwei International Inspection Co., Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen Huatongwei International Inspection Co., Ltd is acknowledged as copyright owner and source of the material. Shenzhen Huatongwei International Inspection Co., Ltd takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test item description ..................... : Soft Mood Light Bluetooth Speaker Trade Mark ....................................... : / Model/Type reference....................... : R087GT Listed Models .................................. : 06-ROQMOOD Manufacturer .................................. : Ansen Electronics Company Modulation Type ............................... : GFSK,8DPSK,π/4DQPSK Operation Frequency ........................ : From 2402MHz to 2480MHz Rating ............................................... : DC 5.0V from USB Result................................................ : Positive Report No.: TRE1308006401 Page 2 of 92 Issued:2013-08-27 T E S T R E P O R T Test Report No. : TRE1308006401 Aug 27, 2013 ______________________________________________________________________________________________ Date of issue Equipment under Test : Soft Mood Light Bluetooth Speaker Model /Type : R087GT Listed Models : 06-ROQMOOD Applicant : Ansen Electronics Company Address : Unit 1401B-1405A Telecom Tower,Wharf T&T Square, 123 Hoi Bun Road, Kwun Tong,Kowloon,Hong Kong Manufacturer : Ansen Electronics Company Address : Chen Tung Industrial Zone,Ning Tau Administrative District,Qiao Tau Zhen,Dongguan,Guangdong Test Result according to the standards on page 4: Positive The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Report No.: TRE1308006401 Page 3 of 92 Issued:2013-08-27 Contents 1. TEST STANDARDS .................................................................. 4 2. SUMMARY ............................................................................. 5 2.1. General Remarks 5 2.2. Equipment Under Test 5 2.3. Short description of the Equipment under Test (EUT) 5 2.4. EUT operation mode 5 2.5. Block Diagram of Test Setup 6 2.6. Related Submittal(s) / Grant (s) 6 2.7. Modifications 6 2.8. NOTE 6 3. TEST ENVIRONMENT ............................................................... 7 3.1. Address of the test laboratory 7 3.2. Test Facility 7 3.3. Environmental conditions 8 3.4. Test Description 8 3.5. Statement of the measurement uncertainty 8 3.6. Equipments Used during the Test 9 4. TEST CONDITIONS AND RESULTS ............................................ 10 4.1. AC Power Conducted Emission 10 4.2. Radiated Emission 13 4.3. Maximum Peak Output Power 18 4.4. 20dB Bandwidth 24 4.5. Band Edge 30 4.6. Frequency Separation 51 4.7. Number of hopping frequency 58 4.8. Time Of Occupancy(Dwell Time) 61 4.9. Pseudorandom Frequency Hopping Sequence 82 4.10. Antenna Requirement 83 5. TEST SETUP PHOTOS OF THE EUT .......................................... 84 Report No.: TRE1308006401 Page 4 of 92 Issued:2013-08-27 1. TEST STANDARDS The tests were performed according to following standards: FCC Rules Part 15.247 : Frequency Hopping, Direct Spread Spectrum and Hybrid Systems that are in operation within the bands of 902-928 MHz, 2400-2483.5 MHz, and 5725-5850 MHz. ANSI C63.10-2009 : American National Standard for Testing Unlicensed Wireless Devices Report No.: TRE1308006401 Page 5 of 92 Issued:2013-08-27 2. SUMMARY 2.1. General Remarks Date of receipt of test sample : Aug 15, 2013 Testing commenced on : Aug 16, 2013 Testing concluded on : Aug 27, 2013 2.2. Equipment Under Test Power supply system utilised Power supply voltage : ○ 120V / 60 Hz ○ 115V / 60Hz ○ 12 V DC ○ 24 V DC ● Other (specified in blank below) DC 5.0V from USB 2.3. Short description of the Equipment under Test (EUT) 2.4GHz (Soft Mood Light Bluetooth Speaker (M/N:R087GT)) For more details, refer to the user’s manual of the EUT. Serial number: Prototype 2.4. EUT operation mode The EUT has been tested under typical operating condition. There are EDR (Enhanced Data Rate) and BDR (Basic Data Rate)mode.The Applicant provides communication tools software to control the EUT for staying in continous transmitting and receiving mode for testing. There are 79 channels of EUT, and the test carried out at the lowest channel, middle channel and highest channel . Channel Frequency(MHz) Channel Frequency(MHz) 0 2402 40 2442 1 2403 41 2443 2 2404 42 2444 3 2405 43 2445 4 2406 44 2446 5 2407 45 2447 6 2408 46…

Text truncated - open the document above for the full version.

Test setup photos of the EUT