LDK-HTIAK2282Cisco Catalyst 9124AX Series Wi-Fi 6 Outdoor Access Points

Cisco Catalyst 9124AX Series Outdoor Access Point Hardware Installation Guide First Published:2021-03-29 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883 THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS. THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY. The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense. The following information is for FCC compliance of Class B devices: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If the equipment causes interference to radio or television reception, which can be determined by turning the equipment off and on, users are encouraged to try to correct the interference by using one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Modifications to this product not authorized by Cisco could void the FCC approval and negate your authority to operate the product. The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California. NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED "AS IS" WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE. IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative content is unintentional and coincidental. All printed copies and duplicate soft copies of this document are considered uncontrolled. See the current online version for the latest version. Cisco has more than 200 offices worldwide. Addresses and phone numbers are listed on the Cisco website at www.cisco.com/go/offices. Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: https://www.cisco.com/c/en/us/about/legal/trademarks.html. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1721R) © 2021 Cisco Systems, Inc. All rights reserved. CONTENTS Prefacevii PREFACE About this Guidevii Conventionsvii Related Documentationviii Cisco Bug Search Toolviii Communications, Services, and Additional Informationviii About the Cisco Catalyst 9124AX Series Outdoor Access Point1 CHAPTER 1 Introduction to Cisco Catalyst 9124AX Series Outdoor Access Point1 Cisco Catalyst 9124AX Series Outdoor Access Point Features1 AP Model Numbers and Regulatory Domains3 Antennas and Radios3 Hardware Features5 CHAPTER 2 Access Point Views, Ports, and Connectors5 Connectors and Ports5 C9124AXI (Internal Antenna) Model: Antenna Radiation Patterns7 C9124AXD (Directional Antenna) Model: Antenna Radiation Patterns10 Power Sources12 Power Injectors13 Ethernet (PoE) Ports13 Unpacking Your Access Point15 CHAPTER 3 Package Contents15 Unpacking the Access Point15 Optional Tools and Hardware from Cisco16 Cisco Catalyst 9124AX Series Outdoor Access Point Hardware Installation Guide iii Addi…

Text truncated - open the document above for the full version.

QA-FR-172-A FCC Confidential Authorization (2021/03/22) FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: LDK-HTIAK2282 In accordance with Sections 0.457 and 0.459 of the Commission’s Rules, Cisco Systems, Inc. hereby requests long-term confidential treatment of information accompanying this application as outlined below: • Block Diagram • Schematics • Operation Description As well as short-term (180 days) confidential treatment of information accompanying this application as outlined below: • Internal Photos • User’s Manual • External Photos • Test Set-up Photos The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely, Samuel Kim Engineering Manager 125 W Tasman Drive San Jose, CA 95134

Cisco Systems, Inc. FCC ID: LDK-HTIAK2282, IC: 2461N-HTIAK2282 EUT External Photographs 1.1 EUT Top View 1.2 EUT Bottom View Cisco Systems, Inc. FCC ID: LDK-HTIAK2282, IC: 2461N-HTIAK2282 1.3 EUT Front View 1.4 EUT Rear View Cisco Systems, Inc. FCC ID: LDK-HTIAK2282, IC: 2461N-HTIAK2282 1.5 EUT Side View

FCC Label Location EUT Bottom View

Cisco Systems, Inc. FCC ID: LDK-HTIAK2282, IC: 2461N-HTIAK2282 EUT Internal Photographs 1.1 EUT – Mainboard Top View 1.2 EUT – Mainboard Bottom View Cisco Systems, Inc. FCC ID: LDK-HTIAK2282, IC: 2461N-HTIAK2282 1.3 EUT – Second PCB Board Top View 1.4 EUT – Second PCB Board Bottom View Cisco Systems, Inc. FCC ID: LDK-HTIAK2282, IC: 2461N-HTIAK2282 1.5 EUT - Internal Antenna Plate Top View 1.6 EUT - Internal Antenna Plate Left Angle Top Cisco Systems, Inc. FCC ID: LDK-HTIAK2282, IC: 2461N-HTIAK2282 1.7 EUT - Internal Plate Bottom Angle

EDCS – 21541326 Maximum Permissible Exposure Study - Engineering Analysis C9124AXI-B Cisco Catalyst C9124AX Series 802.11ax Access Point FCC ID: LDK-HTIAK2282 2400-2483.5 MHz, 5150-5250 MHz, 5250-5350 MHz, 5470-5725 MHz, 5725-5850 MHz Against the following Specifications: 47 Code of Federal Regulations 2.1091 Cisco Systems 170 West Tasman Drive San Jose, CA 95134 Author: Johanna Knudsen Tested By: Johanna Knudsen Approved By: Sam Kim Title: Manager, Radio Compliance Revision: 1 This report replaces any previously entered test report under EDCS – 21541326. This test report has been electronically authorized and archived using the CISCO Doc Central. Test Report Template EDCS# 11556830. EDCS – 21541326 Attestation Statement of Compliance The C9124AXI-B has been evaluated for Maximum Permissible Exposure in compliance with 47 Code of Federal Regulations [Part 1.1307(b) (for fixed devices), Part 2.1091 (for mobile devices), and Part 2.1093 (for portable devices)]. Part 1.1307(b) refers to limits in Part 1.1310 and 2.1093. The evaluation was in accordance with methodology as referenced in KDB 447498 D01 General RF Exposure Guidance v06. This report serves as the additional technical analysis of the Cisco radio modules. This study addresses the following transmitters using the data derived in these test reports:  BLE reports EDCS-21541312, EDCS-21606814  2.4GHz reports EDCS# EDCS-21574927, EDCS-21541314  2.4GHz Auxiliary reports EDCS-21541311, EDCS-21574925  5GHz UNII-1 report EDCS-21574910, EDCS-21541322  5GHz UNII-2 report EDCS-21574912, EDCS-21541323  5GHz UNII-2ext report EDCS-21574913, EDCS-21541324  5GHz UNII-3 report EDCS-21574914, EDCS-21541325  5GHz UNII-1 Auxiliary reports EDCS-21541303, EDCS-21574899  5GHz UNII-2 Auxiliary reports EDCS-21541304, EDCS-21574902  5GHz UNII-2ext Auxiliary reports EDCS-21541305, EDCS-21574903  5GHz UNII-3 Auxiliary reports EDCS-21541306, EDCS-21574904 The limits used for this evaluation are in line with the recommendations of the World Health Organizations (WHO) International Committee on Non-Ionizing Radiation Protection (ICNIRP) as well as the American National Standards Institute (ANSI) C95.1. The limits chosen are of General Population/Uncontrolled Exposure. The following case scenarios were used:  BLE  2.4GHz WLAN  5GHz WLAN  2.4GHz Auxiliary Radio  5GHz Auxiliary Radio This device must be installed to provide a separation distance of at least 30 cm from all persons. Installers must be provided with antenna installation and transmitter operating conditions for satisfying RF exposure compliance. Based on the study this case scenario, the General Population/Uncontrolled Exposure and the minimum recommended distance is around 30cm from the antenna. EDCS – 21541326 1.0 EUT Description The Cisco Catalyst 9124AX Series outdoor access points are next-generation Wi-Fi 6 access points encased in a rugged and robust design that service providers and enterprises can easily deploy. The C9124AXI-B Supports the following radio modes: BLE 5.1 2.4GHz Wi-Fi Radio 802.11b (1-11Mbps) 802.11g (6-54Mbps) 802.11n HT20 (MCS0 – MCS31) 802.11ax HE20 (MCS0-MCS11, 4SS) 2.4GHz Auxiliary Radio 802.11g Non HT20, One Antenna, 6 to 54 Mbps, 1ss 5GHz Wi-Fi Radio: 802.11a (6-54Mbps) 802.11n HT20 (MCS0 – MCS31) 802.11n HT40 (MCS0 – MCS31) 802.11ac VHT20 (MCS0-MCS9, 4SS) 802.11ac VHT40 (MCS0-MCS9, 4SS) 802.11ac VHT80 (MCS0-MCS9, 4SS) 802.11ac VHT160 (MCS0-MCS9, 2SS Max) 802.11ax HE20 (MCS0-MCS11, 4SS) 802.11ax HE40 (MCS0-MCS11, 4SS) 802.11ax HE80 (MCS0-MCS11, 4SS) 802.11ax HE160 (MCS0-MCS9, 2SS Max) 5GHz Auxiliary Radio: 802.11a - Non HT20, One Antenna, 6 to 54 Mbps, 1ss The following antennas are supported by this product series. Please note, the antenna information has been provided by the customer (the Cisco business unit). The data included in this report represent the worst-case data for all antennas. Ithaca (Internal Antenna) Model C9124AXI-x Frequency Antenna Name Antenna Gain 2.4GHz & 5GHz (Wi‐Fi) Antenna 1 TX/RX: internal [email protected] 7dBi@5GHz 2.4GHz & 5GHz (Wi‐Fi) Antenna 2 TX/RX: internal [email protected] 7dBi@5GHz 2.4GHz & 5GHz (Wi‐Fi) Antenna 3 TX/RX: internal [email protected] 7dBi@5GHz 2.4GHz & 5GHz (Wi‐Fi) Antenna 4 TX/RX: internal [email protected] 7dBi@5GHz BLE Antenna T TX/RX: internal 5dBi 2.4GHz & 5GHz (Aux) Antenna A TX/RX: internal [email protected] 7dBi@5GHz 2.4GHz & 5GHz (Aux) Antenna B RX: internal [email protected] 7dBi@5GHz EDCS – 21541326 Methodology All calculations were made in accordance with ANSI C95.1. Measurement Uncertainty Values Parameter Max MU from standard Declared MU Occupied Channel Bandwidth +/- 5% +/-2% RF Output Power, conducted +/- 1,5dB+/-1.4dB Power Spectral Density, conducted +/- 3dB +/- 2dB Unwanted emissions, conducted +/- 3dB +/- 2dB All emissions, radiated +/- 6dB +/- 3.2dB Temperature +/- 3C +/- 0.7C Supply Voltages +/- 3% +/- 2.5% Time +/- 5% +/-2% EDCS – 21541326 2.0 Technical Requirements 2.1 Single Band Operation – Limits FCC Limits for Maximum Permissible Exposure (MPE) (A) Limits for Occupational/Controlled Exposure Frequency Electric Field Magnetic Field Power Density Averaging Time Range Strength (E) Strength (H) (S) |E| 2 , |H| 2 or S (MHz) (V/m) (A/m) (mW/cm 2 ) (minutes) 0.3-3.0 614 1.63 (100)* 6 3.0-30 1842/f 4.89/f (900/f 2 )* 6 30-300 61.4 0.163 1.0 6 300-1500 -- -- f/300 6 1500-100,000 -- -- 5 6 (B) Limits for General Population/Uncontrolled Exposure Frequency Electric Field Magnetic Field Power Density Averaging Time Range Strength (E) Strength (H) (S) |E| 2 , |H| 2 or S (MHz) (V/m) (A/m) (mW/cm 2 ) (minutes) 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180/f 2 )* 30 30-300 27.5 0.073 0.2 30 300-1500 -- -- f/1500 30 1500-100,000 -- -- 1.0 30 f = frequency in MHz *Plane-wave equivalent power density NOTE 1: See Section 1 for discussion of exposure categories. NOTE 2: The averaging time for General Population/Uncontrolled exposure to fixed transmitters is not applicable for mobile and portable transmitters. See 47 CFR §§2.109…

Text truncated - open the document above for the full version.

Test Report C9124AXI-B Cisco Catalyst C9124AX Series 802.11ax Access Point 5GHz Auxiliary Radio FCC ID: LDK-HTIAK2282 5150-5250 MHz Against the following Specifications: CFR47 Part 15.407 Cisco Systems 170 West Tasman Drive San Jose, CA 95134 Author: Johanna Knudsen Tested By: Julian Land, Said Abdelwafi Approved By: Sam Kim Title: Manager, Radio Compliance Revision: 2 This report replaces any previously entered test report under EDCS – 21541303. This test report has been electronically authorized and archived using the CISCO Engineering Document Control system. Test Report Template EDCS# 11644122. This test report has been electronically authorized and archived using the CISCO Engineering Document Control system. SECTION 1: OVERVIEW ......................................................................................................................................... 3 SECTION 2: ASSESSMENT INFORMATION ....................................................................................................... 4 2.1 GENERAL ............................................................................................................................................................. 4 2.2 DATE OF TESTING................................................................................................................................................. 6 2.3 REPORT ISSUE DATE ............................................................................................................................................ 6 2.4 TESTING FACILITIES ............................................................................................................................................. 6 2.5 EQUIPMENT ASSESSED (EUT) .............................................................................................................................. 6 2.6 EUT DESCRIPTION ............................................................................................................................................... 6 SECTION 3: RESULT SUMMARY .......................................................................................................................... 8 3.1 RESULTS SUMMARY TABLE ................................................................................................................................. 8 SECTION 4: SAMPLE DETAILS ........................................................................................................................... 13 APPENDIX A: EMISSION TEST RESULTS ........................................................................................................ 14 CONDUCTED TEST SETUP DIAGRAM ........................................................................................................................ 14 A.1 DUTY CYCLE .................................................................................................................................................... 15 A.2 99% AND 26DB BANDWIDTH ............................................................................................................................ 18 A.3 MAXIMUM CONDUCTED OUTPUT POWER ......................................................................................................... 21 A.4 POWER SPECTRAL DENSITY .............................................................................................................................. 28 A.5 CONDUCTED SPURIOUS EMISSIONS ................................................................................................................... 33 A.6 CONDUCTED BAND EDGE ................................................................................................................................. 43 APPENDIX B: EMISSION TEST RESULTS ........................................................................................................ 47 RADIATED EMISSION SETUP DIAGRAM-BELOW 1G ................................................................................................. 47 B.1 RADIATED SPURIOUS EMISSIONS ...................................................................................................................... 48 B.2 RADIATED EMISSIONS 30MHZ TO 1GHZ .......................................................................................................... 49 B.3 AC CONDUCTED EMISSIONS ............................................................................................................................. 5 0 APPENDIX C: LIST OF TEST EQUIPMENT USED TO PERFORM THE TEST .................................... 51 APPENDIX D: ABBREVIATION KEY AND DEFINITIONS ...................................................................... 53 APPENDIX E: PHOTOGRAPHS OF TEST SETUPS ................................................................................... 54 APPENDIX F: SOFTWARE USED TO PERFORM TESTING ................................................................... 54 APPENDIX G: TEST PROCEDURES ............................................................................................................. 54 APPENDIX H: SCOPE OF ACCREDITATION (A2LA CERTIFICATE NUMBER 1178-01) ................. 54 APPENDIX I: TEST ASSESSMENT PLAN .................................................................................................. 54 APPENDIX J: WORST CASE JUSTIFICATION ............................................................................................... 54 Section 1: Overview The samples were assessed against the tests detailed in section 3 under the requirements of the following specifications: Specifications: CFR47 Part 15.407 Section 2: Assessment Information 2.1 General This report contains an assessment of an apparatus against Electromagnetic Compatibility Standards based upon tests carried out on the samples submitted. The testing was performed by and for the use of Cisco systems Inc: With regard to this assessment, the following points should be noted: a) The results contained in this report relate only to the items tested an…

Text truncated - open the document above for the full version.

Test Report C9124AXI-B Cisco Catalyst C9124AX Series 802.11ax Access Point 5GHz Auxiliary Radio FCC ID: LDK-HTIAK2282 5250-5350 MHz Against the following Specifications: CFR47 Part 15.407 Cisco Systems 170 West Tasman Drive San Jose, CA 95134 Author: Johanna Knudsen Tested By: Julian Land, Said Abdelwafi Approved By: Sam Kim Title: Manager, Radio Compliance Revision: 2 This report replaces any previously entered test report under EDCS – 21541304. This test report has been electronically authorized and archived using the CISCO Engineering Document Control system. Test Report Template EDCS# 11644123. This test report has been electronically authorized and archived using the CISCO Engineering Document Control system. SECTION 1: OVERVIEW ......................................................................................................................................... 3 SECTION 2: ASSESSMENT INFORMATION ....................................................................................................... 4 2.1 GENERAL ............................................................................................................................................................. 4 2.2 DATE OF TESTING................................................................................................................................................. 6 2.3 REPORT ISSUE DATE ............................................................................................................................................ 6 2.4 TESTING FACILITIES ............................................................................................................................................. 6 2.5 EQUIPMENT ASSESSED (EUT) .............................................................................................................................. 6 2.6 EUT DESCRIPTION ............................................................................................................................................... 7 SECTION 3: RESULT SUMMARY .......................................................................................................................... 8 3.1 RESULTS SUMMARY TABLE ................................................................................................................................. 8 SECTION 4: SAMPLE DETAILS ........................................................................................................................... 10 APPENDIX A: EMISSION TEST RESULTS ........................................................................................................ 11 CONDUCTED TEST SETUP DIAGRAM ........................................................................................................................ 11 A.1 DUTY CYCLE .................................................................................................................................................... 12 A.2 99% AND 26DB BANDWIDTH ............................................................................................................................ 14 A.3 MAXIMUM CONDUCTED OUTPUT POWER ......................................................................................................... 17 A.4 POWER SPECTRAL DENSITY .............................................................................................................................. 23 A.5 CONDUCTED SPURIOUS EMISSIONS ................................................................................................................... 29 A.6 CONDUCTED BANDEDGE ................................................................................................................................... 41 APPENDIX B: EMISSION TEST RESULTS ........................................................................................................ 45 RADIATED EMISSION SETUP DIAGRAM-BELOW 1G ................................................................................................. 45 B.1 RADIATED SPURIOUS EMISSIONS ...................................................................................................................... 46 B.2 RADIATED EMISSIONS 30MHZ TO 1GHZ .......................................................................................................... 47 B.3 AC CONDUCTED EMISSIONS ............................................................................................................................. 4 8 APPENDIX C: LIST OF TEST EQUIPMENT USED TO PERFORM THE TEST .......................................... 49 APPENDIX D: ABBREVIATION KEY AND DEFINITIONS ............................................................................. 51 APPENDIX E: PHOTOGRAPHS OF TEST SETUPS .......................................................................................... 52 APPENDIX F: SOFTWARE USED TO PERFORM TESTING ................................................................... 52 APPENDIX G: TEST PROCEDURES ............................................................................................................. 52 APPENDIX H: SCOPE OF ACCREDITATION (A2LA CERTIFICATE NUMBER 1178-01) ................. 52 APPENDIX I: TEST ASSESSMENT PLAN .................................................................................................. 52 APPENDIX J: WORST CASE JUSTIFICATION ............................................................................................... 52 Section 1: Overview The samples were assessed against the tests detailed in section 3 under the requirements of the following specifications: Specifications: CFR47 Part 15.407 Section 2: Assessment Information 2.1 General This report contains an assessment of an apparatus against Electromagnetic Compatibility Standards based upon tests carried out on the samples submitted. The testing was performed by and for the use of Cisco systems Inc: With regard to this assessment, the following points should be noted: a) The results contained in this report relate only t…

Text truncated - open the document above for the full version.

Test Report C9124AXI-B Cisco Catalyst C9124AX Series 802.11ax Access Point 5GHz Auxiliary Radio FCC ID: LDK-HTIAK2282 5470-5725 MHz Against the following Specifications: CFR47 Part 15.407 Cisco Systems 170 West Tasman Drive San Jose, CA 95134 Author: Johanna Knudsen Tested By: Julian Land, Said Abdelwafi Approved By: Sam Kim Title: Manager, Radio Compliance Revision: 2 This report replaces any previously entered test report under EDCS – 21541305. This test report has been electronically authorized and archived using the CISCO Engineering Document Control system. Test Report Template EDCS# 11644124. This test report has been electronically authorized and archived using the CISCO Engineering Document Control system. SECTION 1: OVERVIEW ......................................................................................................................................... 3 SECTION2: ASSESSMENT INFORMATION ........................................................................................................ 4 2.1 GENERAL ............................................................................................................................................................. 4 2.2 DATE OF TESTING................................................................................................................................................. 6 2.3 REPORT ISSUE DATE ............................................................................................................................................ 6 2.4 TESTING FACILITIES ............................................................................................................................................. 6 2.5 EQUIPMENT ASSESSED (EUT) .............................................................................................................................. 6 2.6 EUT DESCRIPTION ............................................................................................................................................... 6 SECTION 3: RESULT SUMMARY .......................................................................................................................... 8 3.1 RESULTS SUMMARY TABLE ................................................................................................................................. 8 SECTION 4: SAMPLE DETAILS ............................................................................................................................. 9 APPENDIX A: EMISSION TEST RESULTS ........................................................................................................ 10 CONDUCTED TEST SETUP DIAGRAM ........................................................................................................................ 10 A.1 DUTY CYCLE .................................................................................................................................................... 11 A.2 99% AND 26DB BANDWIDTH ............................................................................................................................ 13 A.3 MAXIMUM CONDUCTED OUTPUT POWER ......................................................................................................... 17 A.4 POWER SPECTRAL DENSITY .............................................................................................................................. 23 A.5 CONDUCTED SPURIOUS EMISSIONS ................................................................................................................... 29 A.6 CONDUCTED BANDEDGE ................................................................................................................................... 41 APPENDIX B: EMISSION TEST RESULTS ........................................................................................................ 47 RADIATED EMISSION SETUP DIAGRAM-BELOW 1G ................................................................................................. 47 B.1 RADIATED SPURIOUS EMISSIONS ..................................................................................…

Text truncated - open the document above for the full version.