LDK-ONT4TVCWGPON ONT

REVIEWDRAFT- CISCOCONFIDENTIAL CiscoCatalystPONSeriesSwitchesHardwareInstallationGuide FirstPublished:2020-11-08 AmericasHeadquarters CiscoSystems,Inc. 170 West TasmanDrive SanJose,CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000 800 553-NETS(6387) Fax:408 527-0883 CONTENTS Prefacevii PREFACE DocumentConventionsvii RelatedDocumentationix ObtainingDocumentationand Submittinga ServiceRequestix Introductionto the Passive OpticalNetwork1 CHAPTER1 Cisco CatalystPON Series OLT Overview2 Cisco CatalystPON Series OLT Models2 Front Panel3 Rear Panel4 Ports4 Power Supply5 LEDs6 Cisco CatalystPON Series ONT Overview7 Cisco CatalystPON Series ONT Models8 Front Panel8 Rear Panel10 Side Panel10 Top Panel11 Ports13 LEDs13 Lock Slot15 Cisco CatalystPON ManagerOverview15 Installation17 CHAPTER2 CiscoCatalystPONSeriesSwitchesHardwareInstallationGuide ii Contents REVIEWDRAFT- CISCOCONFIDENTIAL Safety Warnings17 Box Contents20 InstallationGuidelines22 Installingan OLT22 Mountingthe OLT on a Table or Shelf22 Attachingthe Rack-MountingBracketand Mountinga OLT on a Rack23 InstallingSFP or SFP+ Modules24 Installingan SFP or SFP+ Module24 Removingan SFP or SFP+ Module25 Establishingthe SystemGround25 RequiredTools and Equipment26 Connectingthe SystemGround26 Connectingto the Power Source28 Connectingto an AC Power Source28 Connectingto a DC Power Source29 SettingUp the OLT30 Installingan ONT30 Placingthe ONT on a Table or Shelf31 Installingthe ONT on a Wall31 Attachingthe Rack-MountingBracketand Mountingan ONT on a Rack32 Connectingto an AC Power Source33 SettingUp an ONT34 Installingthe Cisco CatalystPON Manager34 SettingUp the Cisco CatalystPON Manager39 Startingthe PON ManagerServer39 Creatinga New User in the PON ManagerClient40 Removingand ReplacingField-ReplaceableUnits(FRUs)45 CHAPTER3 Removingand Replacingthe Fan Module45 InstallationGuidelines45 Removingthe Fan Module45 Installinga Fan Module47 Removingand Replacingthe Power SupplyModule47 InstallationGuidelines48 CiscoCatalystPONSeriesSwitchesHardwareInstallationGuide iii Contents REVIEWDRAFT- CISCOCONFIDENTIAL Removingand InstallingPower SupplyBlank Cover49 Removinga Power SupplyBlank Cover49 Installinga Power SupplyBlank Cover49 Removinga Power SupplyModulefrom an OLT49 Insertingthe Power SupplyModulein an OLT52 Troubleshooting55 CHAPTER4 TroubleshootingCommonIssues55 Bad or DamagedCable55 Ethernetand Fiber-OpticCables55 Link Status56 10/100/1000PoE+ Port Connections56 Cisco CatalystPON Series OLT Troubleshooting56 SFP and SFP+ Module56 Fan Module57 Power SupplyModule57 InterfaceIndicator57 Findinga Cisco CatalystPON OLT Serial Number57 Cisco CatalystPON Series ONT Troubleshooting58 Findingthe Cisco CatalystPON ONT Serial Number58 TechnicalSpecifications59 APPENDIXA Cisco CatalystPON Series OLT TechnicalSpecifications59 PhysicalSpecifications59 EnvironmentalSpecifications59 Power Requirements60 Cisco CatalystPON Series ONT TechnicalSpecifications60 PhysicalSpecifications60 EnvironmentalSpecifications61 Power Requirements61 Connectorand CableSpecifications63 APPENDIXB ConnectorSpecifications63 10/100/1000Ports (IncludingPoE)63 CiscoCatalystPONSeriesSwitchesHardwareInstallationGuide iv Contents REVIEWDRAFT- CISCOCONFIDENTIAL SFP ModuleConnectors63 Cablesand Adapters64 TransceiverModuleNetworkCables64 Cable Pinouts65 ConsolePort AdapterPinouts66 CiscoCatalystPONSeriesSwitchesHardwareInstallationGuide v Contents REVIEWDRAFT- CISCOCONFIDENTIAL CiscoCatalystPONSeriesSwitchesHardwareInstallationGuide vi Contents REVIEWDRAFT- CISCOCONFIDENTIAL Preface Thisprefacedescribestheconventionsofthisdocumentandinformationonhowtoobtainotherdocumentation. It also providesinformationon what's new in Cisco productdocumentation. The documentationset for this productstrives to use bias-freelanguage.For purposesof this documentation set, bias-freeis definedas languagethat does not imply discriminationbased on age, disability, gender, racial identity, ethnic identity, sexual orientation,socioeconomicstatus, and intersectionality. Exceptionsmay be presentin the documentationdue to languagethat is hardcodedin the user interfacesof the productsoftware, languageused based on RFP documentation,or languagethat is used by a referencedthird-partyproduct. Note • DocumentConventions, on page vii • RelatedDocumentation, on page ix • ObtainingDocumentationand Submittinga ServiceRequest, on page ix DocumentConventions This documentuses the followingconventions: DescriptionConvention Both the^symboland Ctrl representthe Control(Ctrl) key on a keyboard.For example,thekeycombination^DorCtrl-DmeansthatyouholddowntheControl key while you press the D key. (Keys are indicatedin capitalletters but are not case sensitive.) ^ or Ctrl Commandsand keywordsand user-enteredtext appearinboldfont.boldfont Documenttitles, new or emphasizedterms, and argumentsfor which you supply values are initalicfont. Italicfont Terminalsessionsand informationthe systemdisplaysappearincourierfont.Courierfont Bold Courierfont indicatestext that the user must enter.Bold Courierfont Elementsin square bracketsare optional.[x] CiscoCatalystPONSeriesSwitchesHardwareInstallationGuide vii DescriptionConvention An ellipsis(three consecutivenonboldedperiodswithoutspaces)after a syntax elementindicatesthat the elementcan be repeated. ... A verticalline, called a pipe, indicatesa choice within a set of keywordsor arguments. | Optionalalternativekeywordsare groupedin bracketsand separatedby vertical bars. [x | y] Requiredalternativekeywordsare groupedin braces and separatedby vertical bars. {x | y} Nestedsetofsquarebracketsorbracesindicateoptionalorrequiredchoiceswithin optionalor requiredelements.Bracesand a verticalbar within square brackets indicatea requiredchoice within an optionalelement. [x {y | z}] A nonquotedset of characters.Do not use quotationmarks aroundthe string or the string will includethe quotationmarks. string Nonprintingcharacterssuch as passwordsare in angle brackets.< > Defaultresponsesto systemprompts…

Text truncated - open the document above for the full version.

Product:GPONONT FCCID:LDK-ONT4TVCW Model:CGP-ONT-4TVCW Brand:CISCO Sincerely, Name:HaiwenLu CompliancePM [email protected] Date:2021-05-20 Attestation Letter Federal Communications Commission Authorization and Evaluation Division We Name: Cisco Systems Inc Address: 125 West Tasman Drive, San Jose, California, United States 95134-1706 Declare that the device does not support channel 12 ~ 13 in 2.4GHz band and any non-US channels in all the operational mode(s) for the following product.

DeclarationofConformityPage 1 of1 DeclarationofConformity Date:June01,2021 FederalCommunicationsCommission AuthorizationandEvaluationDivision FCCID:LDK-ONT4TVCW Pleasebenotifiedthatwe,theundersigned, CiscoSystemsIncdeclaresthattheproductwhichbearstheaboveFCCIDis alsocompliantwiththeFCCrequirementsforsDOC.AndthesDOCprocedure shallbecarriedoutpriortomarketingthedeviceintheUS. Sincerely, _________________ Name:HaiwenLu CompliancePM [email protected] Date:2021-06-01

EDCS-1216337 09/30/2020 Subject : Authorized signatures The following people are authorized by Cisco Systems to sign documents for FCC product approval under FCC Grantee code LDK, and ISED product approval under ISED registration 2461N on behalf of the company. Further this right is extended to any regular Cisco employee as deemed necessary. Louie Castro Jialei Xue Adam Walb Lillian Yao Howard Ji Haiwen Lu Jose Aguirre Allesandro Erta Emily Jaser Bogdan Tudosoiu Rekha Simha Andrea Orioli Guangmin Ouyang Rochelle Jacobsen Regards Samuel Kim Cisco Systems

AgentCompanyname:MRTTechnology(Suzhou)Co.,Ltd Address:D8Building,YouxinIndustrialPark,No.2Tian'edang Rd.,WuzhongEconomicDevelopmentZone City:Suzhou Country:China isauthorizedtoapplyforCertificationofthefollowingproduct(s): Product:GPONONT FCCID:LDK-ONT4TVCW Model:CGP-ONT-4TVCW Brand:CISCO Sincerely, _________________ Name:HaiwenLu CompliancePM [email protected] Date:2021-05-20 Declaration of Authorization We Name: Cisco Systems Inc Address: 125 West Tasman Drive, San Jose, California, United States 95134-1706 Declare that: Name Representative of agent: Marlin Chen

ConfidentialityRequestLetter FederalCommunicationsCommission AuthorizationandEvaluationDivision FCCID:LDK-ONT4TVCW ConfidentialityRequest PursuanttoSections0.457and0.459oftheCommission’sRules,weherebyrequest confidentialtreatmentofinformationaccompanyingthisapplicationasoutlinedbelow: 1.BlockDiagram 2.Schematics 3.OperationalDescription Theabovematerialscontaintradesecretsandproprietaryinformationnotcustomarily releasedtothepublic.Thepublicdisclosureofthesemattersmightbeharmfultothe applicantandprovideunjustifiedbenefitstoitscompetitors. TheapplicantunderstandsthatpursuanttoRule0.457,disclosureofthisapplicationand allaccompanyingdocumentationwillnotbemadebeforethedateoftheGrantforthis application. Sincerely, _________________ Name:HaiwenLu CompliancePM [email protected] Date:2021-05-20

Report No.: 2009RSU002-UE 1 of 2 EUT External Photograph (1) EUT Photo (2) EUT Photo Report No.: 2009RSU002-UE 2 of 2 (3) EUT Photo (4) EUT Photo

Report No.: 2009RSU002-UE 1 of 5 EUT Internal Photograph (1) EUT Photo (2) EUT Photo Report No.: 2009RSU002-UE 2 of 5 (3) EUT Photo (4) EUT Photo Report No.: 2009RSU002-UE 3 of 5 (5) EUT Photo (6) EUT Photo Report No.: 2009RSU002-UE 4 of 5 (7) EUT Photo (8) EUT Photo Report No.: 2009RSU002-UE 5 of 5 (9) EUT Photo

MRT Technology (Suzhou) Co., Ltd Report No.: 2009RSU002-U4 Phone: +86-512-66308358 Report Version: V01 Web: www.mrt-cert.com Issue Date: 06-01-2021 1 of 8 RF Exposure Evaluation Declaration FCC ID: LDK-ONT4TVCW Applicant: Cisco Systems, Inc. Application Type: Certification Product: GPON ONT Model No.: CGP-ONT-4TVCW Trademark: CISCO FCC Classification: Digital Transmission System (DTS) Unlicensed National Information Infrastructure (NII) Test Date: December 30 ~ 31, 2020 Reviewed By: Vincent Yu Approved By: Robin Wu The test results relate only to the samples tested. The test results shown in the test report are traceable to the national/international standards through the calibration of the equipment and evaluated measurement uncertainty herein. The test report shall not be reproduced except in full without the written approval of MRT Technology (Suzhou) Co., Ltd. Report No.: 2009RSU002-U4 2 of 8 Revision History Report No. Version Description Issue Date Note 2009RSU002-U4 Rev. 01 Initial Report 06-01-2021 Valid Report No.: 2009RSU002-U4 3 of 8 CONTENTS Description Page 1. General Information ............................................................................................................ 4 1.1. Applicant ............................................................................................................................... 4 1.2. Manufacturer ........................................................................................................................ 4 1.3. Testing Facility ..................................................................................................................... 4 2. Product Information ............................................................................................................ 5 2.1. Feature of Equipment under Test ..................................................................................... 5 2.2. Description of Available Antennas..................................................................................... 5 3. RF Exposure Evaluation ..................................................................................................... 6 3.1. Limits ..................................................................................................................................... 6 3.2. Test Result of RF Exposure Evaluation ........................................................................... 7 Appendix - EUT Photograph ...................................................................................................... 8 Report No.: 2009RSU002-U4 4 of 8 1. General Information 1.1. Applicant Cisco Systems, Inc. 125 West Tasman Drive, San Jose, California, United States 95134-1706 1.2. Manufacturer Cisco Systems, Inc. 125 West Tasman Drive, San Jose, California, United States 95134-1706 1.3. Testing Facility Test Site – MRT Suzhou Laboratory Laboratory Location (Suzhou - Wuzhong) D8 Building, No.2 Tian’edang Rd., Wuzhong Economic Development Zone, Suzhou, China Laboratory Location (Suzhou - SIP) 4b Building, Liando U Valley, No.200 Xingpu Rd., Shengpu Town, Suzhou Industrial Park, China Laboratory Accreditations A2LA: 3628.01 CNAS: L10551 FCC: CN1166 ISED: CN0001 VCCI: R-20025, G-20034, C-20020, T-20020 Test Site – MRT Shenzhen Laboratory Laboratory Location (Shenzhen) 1G, Building A, Junxiangda Building, Zhongshanyuan Road West, Nanshan District, Shenzhen, China Laboratory Accreditations A2LA: 3628.02 CNAS: L10551 FCC: CN1284 ISED: CN0105 Test Site – MRT Taiwan Laboratory Laboratory Location (Taiwan) No. 38, Fuxing 2nd Rd., Guishan Dist., Taoyuan City 333, Taiwan (R.O.C.) Laboratory Accreditations TAF: L3261-190725 FCC: 291082, TW3261 ISED: TW3261 Report No.: 2009RSU002-U4 5 of 8 2. Product Information 2.1. Feature of Equipment under Test 2.2. Description of Available Antennas Antenna Type Frequency Band (MHz) T X Paths Number of spatial streams Max Antenna Gain (dBi) CDD Directional Gain (dBi) For Power For PSD PCB Antenna 2412 ~ 2462 2 1 3.80 3.80 6.81 5180 ~ 5825 2 1 3.34 3.34 6.35 Note: The EUT supports Cyclic Delay Diversity (CDD) mode, and CDD signals are correlated. If all antennas have the same gain, G ANT , Directional gain = G ANT + Array Gain, where Array Gain is as follows. • For power spectral density (PSD) measurements on all devices, Array Gain = 10 log 10 (N ANT / N SS ) dB; • For power measurements on IEEE 802.11 devices, Array Gain = 0 dB for N ANT ≤ 4; Product Name GPON ONT Model No. CGP-ONT-4TVCW Wi-Fi Specification 802.11a/b/g/n/ac Operating Temp. -5 ~ 45°C Power Supply External Power Adapter Firmware Version 1.1.3.3_03 Accessories Adapter MODEL: DSA-18PFR-12 FUS 120150 INPUT: 100-240V~50/60Hz 0.6A OUTPUT: 12VDC, 1.5A, 18.0W Report No.: 2009RSU002-U4 6 of 8 3. RF Exposure Evaluation 3.1. Limits According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in 1.1307(b) LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (Minutes) (A) Limits for Occupational/ Control Exposures 300-1500 -- -- f/300 6 1500-100,000 -- -- 5 6 (B) Limits for General Population/ Uncontrolled Exposures 300-1500 -- -- f/1500 6 1500-100,000 -- -- 1 30 f= Frequency in MHz Calculation Formula: Pd = (Pout*G)/(4*pi*r 2 ) Where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 r = distance between observation point and center of the radiator in cm Pd is the limit of MPE, 1mW/cm². If we know the maximum gain of the antenna and the total power input to the antenna, through the calculation, we will know the distance r where the MPE limit is reached. Report No.: 2009RSU002-U4 7 of 8 3.2. Test Result of RF Exposure Evaluation Product GPON ONT Test Item RF Exposure Evaluation Antenna Gain: Refer to clause 2.2. Test …

Text truncated - open the document above for the full version.

MRT Technology (Suzhou) Co., Ltd Report No.: 2009RSU002-U3 Phone: +86-512-66308358 Report Version: V01 Web: www.mrt-cert.com Issue Date: 06-01-2021 1 of 117 FCC ID: LDK-ONT4TVCW Applicant: Cisco Systems, Inc. Application Type: Certification Product: GPON ONT Model No.: CGP-ONT-4TVCW Brand Name: CISCO FCC Classification: Unlicensed National Information Infrastructure (NII) Type of Device: Master Device FCC Rule Part(s): Part 15 Subpart E - 15.407 Section (h)(2) KDB 905462 D02v02, KDB 905462 D04v01 Test Date: September 22 ~ October 09, 2020 Reviewed By: Vincent Yu Approved By: Robin Wu DFS MEASUREMENT REPORT FCC 15.407 WLAN 802.11a/n/ac The test results relate only to the samples tested. This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in KDB 905462 D02v02. Test results reported herein relate only to the item(s) tested. The test report shall not be reproduced except in full without the written approval of MRT Technology (Suzhou) Co., Ltd. Report No.: 2009RSU002-U3 2 of 117 Revision History Report No. Version Description Issue Date Note 2009RSU002-U3 Rev. 01 Initial Report 06-01-2021 Valid Report No.: 2009RSU002-U3 3 of 117 CONTENTS Description Page 1. GENERAL INFORMATION ..................................................................................................... 5 1.1. Applicant ....................................................................................................................... 5 1.2. Manufacturer ................................................................................................................ 5 1.3. Testing Facility .............................................................................................................. 5 2. PRODUCT INFORMATION ..................................................................................................... 6 2.1. Equipment Description .................................................................................................. 6 2.2. Product Specification Subjective to this Report ............................................................. 6 2.3. DFS Band Carrier Frequencies Operation .................................................................... 7 2.4. Description of Available Antennas ................................................................................ 7 2.5. Test Mode .................................................................................................................... 8 2.6. Test Environment Condition .......................................................................................... 8 3. DFS DETECTION THRESHOLDS AND RADAR TEST WAVEFORMS................................... 9 3.1. Applicability .................................................................................................................. 9 3.2. DFS Devices Requirements ........................................................................................ 10 3.3. DFS Detection Threshold Values ................................................................................. 11 3.4. Parameters of DFS Test Signals ................................................................................. 12 3.5. Conducted Test Setup ................................................................................................ 15 4. TEST EQUIPMENT CALIBRATION DATE ............................................................................ 16 5. TEST RESULT ...................................................................................................................... 17 5.1. Summary .................................................................................................................... 17 5.2. Radar Waveform Calibration ....................................................................................... 18 5.2.1. Calibration Setup ........................................................................................................ 18 5.2.2. Calibration Procedure ................................................................................................. 18 5.2.3. Cablibration Result ..................................................................................................... 19 5.2.4. Channel Loading Test Result ...................................................................................... 21 5.3. NII Detection Bandwidth Measurement ....................................................................... 22 5.3.1. Test Limit .................................................................................................................... 22 5.3.2. Test Procedure ........................................................................................................... 22 5.3.3. Test Result .................................................................................................................. 24 5.4. Initial Channel Availability Check Time Measurement ................................................. 27 5.4.1. Test Limit .................................................................................................................... 27 5.4.2. Test Procedure ........................................................................................................... 27 5.4.3. Test Result .................................................................................................................. 28 5.5. Radar Burst at the Beginning of the Channel Availability Check Time Measurement .. 29 Report No.: 2009RSU002-U3 4 of 117 5.5.1. Test Limit .................................................................................................................... 29 5.5.2. Test Procedure ........................................................................................................... 29 5.5.3. Test Result ..........................................................................…

Text truncated - open the document above for the full version.

Report No.: 2009RSU002-U2 180 of 283 Site: WZ-AC2 Time: 2020/09/09 - 21:38 Limit: FCC_Part15.209_RE(3m) Engineer: Antony Yang Probe: AC1_BBHA9120D_1-18GHz Polarity: Vertical EUT: GPON ONT Power: AC 120V/60Hz Test Mode: Transmit by 802.11n-HT20 at channel 5240MHz (CDD Mode) No Flag Mark Frequency (MHz) Measure Level (dBuV/m) Reading Level (dBuV) Margin (dB) Limit (dBuV/m) Factor (dB) Type 1 * 5235.760 105.371 99.274 N/A N/A 6.098 PK 2 5350.000 63.986 57.528 -10.014 74.000 6.458 PK 3 5354.080 64.382 58.041 -9.618 74.000 6.340 PK Note: Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) - Pre_Amplifier Gain (dB) Report No.: 2009RSU002-U2 181 of 283 Site: WZ-AC2 Time: 2020/09/09 - 21:40 Limit: FCC_Part15.209_RE(3m) Engineer: Antony Yang Probe: AC1_BBHA9120D_1-18GHz Polarity: Vertical EUT: GPON ONT Power: AC 120V/60Hz Test Mode: Transmit by 802.11n-HT20 at channel 5240MHz (CDD Mode) No Flag Mark Frequency (MHz) Measure Level (dBuV/m) Reading Level (dBuV) Margin (dB) Limit (dBuV/m) Factor (dB) Type 1 * 5236.640 95.399 89.308 N/A N/A 6.090 AV 2 5350.000 47.488 41.030 -6.512 54.000 6.458 AV 3 5355.280 47.549 41.239 -6.451 54.000 6.310 AV Note: Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) - Pre_Amplifier Gain (dB) Report No.: 2009RSU002-U2 182 of 283 Site: WZ-AC2 Time: 2020/09/09 - 21:43 Limit: FCC_Part15.209_RE(3m) Engineer: Antony Yang Probe: AC1_BBHA9120D_1-18GHz Polarity: Horizontal EUT: GPON ONT Power: AC 120V/60Hz Test Mode: Transmit by 802.11n-HT20 at channel 5320MHz (CDD Mode) No Flag Mark Frequency (MHz) Measure Level (dBuV/m) Reading Level (dBuV) Margin (dB) Limit (dBuV/m) Factor (dB) Type 1 * 5317.600 107.214 101.123 N/A N/A 6.090 PK 2 5350.000 62.136 55.678 -11.864 74.000 6.458 PK 3 5352.720 64.107 57.731 -9.893 74.000 6.377 PK Note: Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) - Pre_Amplifier Gain (dB) Report No.: 2009RSU002-U2 183 of 283 Site: WZ-AC2 Time: 2020/09/09 - 21:47 Limit: FCC_Part15.209_RE(3m) Engineer: Antony Yang Probe: AC1_BBHA9120D_1-18GHz Polarity: Horizontal EUT: GPON ONT Power: AC 120V/60Hz Test Mode: Transmit by 802.11n-HT20 at channel 5320MHz (CDD Mode) No Flag Mark Frequency (MHz) Measure Level (dBuV/m) Reading Level (dBuV) Margin (dB) Limit (dBuV/m) Factor (dB) Type 1 * 5316.360 96.935 90.871 N/A N/A 6.064 AV 2 5350.000 48.434 41.976 -5.566 54.000 6.458 AV Note: Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) - Pre_Amplifier Gain (dB) Report No.: 2009RSU002-U2 184 of 283 Site: WZ-AC2 Time: 2020/09/09 - 21:49 Limit: FCC_Part15.209_RE(3m) Engineer: Antony Yang Probe: AC1_BBHA9120D_1-18GHz Polarity: Vertical EUT: GPON ONT Power: AC 120V/60Hz Test Mode: Transmit by 802.11n-HT20 at channel 5320MHz (CDD Mode) No Flag Mark Frequency (MHz) Measure Level (dBuV/m) Reading Level (dBuV) Margin (dB) Limit (dBuV/m) Factor (dB) Type 1 * 5313.200 103.164 97.167 N/A N/A 5.997 PK 2 5350.000 62.625 56.167 -11.375 74.000 6.458 PK 3 5368.320 64.077 57.966 -9.923 74.000 6.111 PK Note: Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) - Pre_Amplifier Gain (dB) Report No.: 2009RSU002-U2 185 of 283 Site: WZ-AC2 Time: 2020/09/09 - 21:51 Limit: FCC_Part15.209_RE(3m) Engineer: Antony Yang Probe: AC1_BBHA9120D_1-18GHz Polarity: Vertical EUT: GPON ONT Power: AC 120V/60Hz Test Mode: Transmit by 802.11n-HT20 at channel 5320MHz (CDD Mode) No Flag Mark Frequency (MHz) Measure Level (dBuV/m) Reading Level (dBuV) Margin (dB) Limit (dBuV/m) Factor (dB) Type 1 * 5313.520 91.028 85.024 N/A N/A 6.003 AV 2 5350.000 47.532 41.074 -6.468 54.000 6.458 AV 3 5350.960 47.595 41.167 -6.405 54.000 6.427 AV Note: Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) - Pre_Amplifier Gain (dB) Report No.: 2009RSU002-U2 186 of 283 Site: WZ-AC2 Time: 2020/09/09 - 21:53 Limit: FCC_Part15.209_RE(3m) Engineer: Antony Yang Probe: AC1_BBHA9120D_1-18GHz Polarity: Horizontal EUT: GPON ONT Power: AC 120V/60Hz Test Mode: Transmit by 802.11n-HT20 at channel 5500MHz (CDD Mode) No Flag Mark Frequency (MHz) Measure Level (dBuV/m) Reading Level (dBuV) Margin (dB) Limit (dBuV/m) Factor (dB) Type 1 5443.950 59.093 52.653 -14.907 74.000 6.440 PK 2 5460.000 57.875 51.389 -16.125 74.000 6.486 PK 3 5464.920 65.450 58.945 -2.750 68.200 6.505 PK 4 5470.000 62.314 55.789 -5.886 68.200 6.524 PK 5 * 5501.370 108.547 102.026 N/A N/A 6.521 PK Note: Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) - Pre_Amplifier Gain (dB) Report No.: 2009RSU002-U2 187 of 283 Site: WZ-AC2 Time: 2020/09/09 - 21:56 Limit: FCC_Part15.209_RE(3m) Engineer: Antony Yang Probe: AC1_BBHA9120D_1-18GHz Polarity: Horizontal EUT: GPON ONT Power: AC 120V/60Hz Test Mode: Transmit by 802.11n-HT20 at channel 5500MHz (CDD Mode) No Flag Mark Frequency (MHz) Measure Level (dBuV/m) Reading Level (dBuV) Margin (dB) Limit (dBuV/m) Factor (dB) Type 1 5452.770 45.391 38.927 -8.609 54.000 6.464 AV 2 5460.000 45.254 38.768 -8.746 54.000 6.486 AV 3 5470.000 46.115 39.590 -7.885 54.000 6.524 AV 4 * 5502.630 97.249 90.722 N/A N/A 6.527 AV Note: Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) - Pre_Amplifier Gain (dB) Report No.: 2009RSU002-U2 188 of 283 Site: WZ-AC2 Time: 2020/09/09 - 21:58 Limit: FCC_Part15.209_RE(3m) Engineer: Antony Yang Probe: AC1_BBHA9120D_1-18GHz Polarity: Vertical EUT: GPON ONT Power: AC 120V/60Hz Test Mode: Transmit by 802.11n-HT20 at channel 5500MHz (CDD Mode) No Flag Mark Frequency (MHz) Measure Level (dBuV/m) Reading Level (dBuV) Margin (dB) Limit (dBuV/m) Factor (dB) Type 1 5447.955 59.614 53.163 -14.386 74.000 6.450 PK 2 5460.000 58.566 52.080 -15.…

Text truncated - open the document above for the full version.

Report No.: 2009RSU002-U2 66 of 283 802.11n-HT20 Power Spectral Density - Ant 1 / Ant 0 + 1 Channel 36 (5180MHz) Channel 44 (5220MHz) Channel 48 (5240MHz) Channel 52 (5260MHz) Channel 60 (5300MHz) Channel 64 (5320MHz) Channel 100 (5500MHz) Channel 116 (5580MHz) Report No.: 2009RSU002-U2 67 of 283 802.11n-HT20 Power Spectral Density - Ant 1 / Ant 0 + 1 Channel 140 (5700MHz) Channel 144 (5720MHz) Channel 149 (5745MHz) Channel 157 (5785MHz) Channel 165 (5825MHz) Report No.: 2009RSU002-U2 68 of 283 802.11n-HT40 Power Spectral Density - Ant 1 / Ant 0 + 1 Channel 38 (5190MHz) Channel 46 (5230MHz) Channel 54 (5270MHz) Channel 62 (5310MHz) Channel 102 (5510MHz) Channel 110 (5550MHz) Channel 134 (5670MHz) Channel 142 (5710MHz) Report No.: 2009RSU002-U2 69 of 283 802.11n-HT40 Power Spectral Density - Ant 1 / Ant 0 + 1 Channel 151 (5755MHz) Channel 159 (5795MHz) Report No.: 2009RSU002-U2 70 of 283 802.11ac-VHT20 Power Spectral Density - Ant 1 / Ant 0 + 1 Channel 36 (5180MHz) Channel 44 (5220MHz) Channel 48 (5240MHz) Channel 52 (5260MHz) Channel 60 (5300MHz) Channel 64 (5320MHz) Channel 100 (5500MHz) Channel 116 (5580MHz) Report No.: 2009RSU002-U2 71 of 283 802.11ac-VHT20 Power Spectral Density - Ant 1 / Ant 0 + 1 Channel 140 (5700MHz) Channel 144 (5720MHz) Channel 149 (5745MHz) Channel 157 (5785MHz) Channel 165 (5825MHz) Report No.: 2009RSU002-U2 72 of 283 802.11ac-VHT40 Power Spectral Density - Ant 1 / Ant 0 + 1 Channel 38 (5190MHz) Channel 46 (5230MHz) Channel 54 (5270MHz) Channel 62 (5310MHz) Channel 102 (5510MHz) Channel 110 (5550MHz) Channel 134 (5670MHz) Channel 142 (5710MHz) Report No.: 2009RSU002-U2 73 of 283 802.11ac-VHT40 Power Spectral Density - Ant 1 / Ant 0 + 1 Channel 151 (5755MHz) Channel 159 (5795MHz) Report No.: 2009RSU002-U2 74 of 283 802.11ac-VHT80 Power Spectral Density - Ant 1 / Ant 0 + 1 Channel 42 (5210MHz) Channel 58 (5290MHz) Channel 106 (5530MHz) Channel 122 (5610MHz) Channel 138 (5690MHz) Channel 155 (5775MHz) Report No.: 2009RSU002-U2 75 of 283 6.7. Frequency Stability Measurement 6.7.1.Test Limit Manufactures of U-NII devices are responsible for ensuring frequency stability such that an emission is maintained within the band of operation under all conditions of normal operation as specified in the user’s manual. 6.7.2.Test Procedure Used Frequency Stability Under Temperature Variations: The equipment under test was connected to an external AC or DC power supply and input rated voltage. RF output was connected to a frequency counter or spectrum analyzer via feed through attenuators. The EUT was placed inside the temperature chamber. Set the spectrum analyzer RBW low enough to obtain the desired freque…

Text truncated - open the document above for the full version.