LU9276210Remote Control Toy Transmitter

TARANTULA RC TM Ages 8+ Instruction Manual Race the Tarantula 27 MHz Ascendor EKO-05 against the Tarantula 49 MHz MG-A1 Quadtrax for awesome competitive action! SPECIFICATIONS Includes: -Tarantula -Full-Function Handset -Instruction Manual Requires (included in Bonus Pack only): -1x 9.6V 700mAh NiCd Battery Pack -4-hour Charger for 9.6V 700mAh NiCd Battery Pack -1x 9V Battery CHARGING THE BATTERY Before you can experience all the fun and excitement of using your toy, you must charge your Battery Pack. Follow these simple instructions for your initial charge-up and all recharges thereafter. 1. Connect the Battery Charger Connector into the 9.6V NiCd Rechargeable Battery Pack. 2. Plug the Battery Charger into a standard wall 120V outlet. 3. Allow the Battery Pack to charge for 4 hours. 4. Disconnect the Battery Pack from the Battery Charger and remove the Battery Charger from the wall outlet. It should feel warm. Note:Battery life varies depending on usage. An average charge should last approximately 3 to 15 minutes. The rechargeable battery should be charged by an adult. Important: -After use, the Battery Pack may be hot. Allow it to cool for at least 20 minutes before recharging. -If the Battery Pack shows signs of leakage or erosion, do not recharge; replace it immediately. -Do not disassemble the Battery Pack. -If the battery pack or charging unit becomes wet, dry thoroughly before recharging. -Do not use any other rechargeable battery except for the standard 9.6V NiCd Battery Pack that was intended solely for use with the product. -The Battery Charger used with the toy is to be regularly examined for damage to the plug, enclosure and other parts. In the event of such damage, the toy must not be used with this battery charger until the damage has been repaired. -The product is not intended for children under 3 years old. -The product must only be used with the recommended battery charger. -The battery charger is not a toy. INSTALLATION OF BATTERIES Remote Controller: 1. Switch the power to the "OFF" position. 2. Unscrew and remove the battery compartment cover, located on the back of the handset, with a Phillips screwdriver. 3. Insert 1 x 9V battery in the proper direction as indicated inside the battery compartment. 4. Put the battery cover back on & tighten the screw securely. 5. Switch the power to the "ON" position. 6. Push the button to the further to play with Headlights. Vehicle: 1. Push the button at the rear top of vehicle to power off the vehicle, the green indicator inside the small doom located at the top of vehicle should be off. 2. Unscrew and remove the battery door at the back of the vehicle. 3. Plug a fully charged 9.6V NiCd Battery Pack. 4. Put the battery door back on & screw it securely. 5. Press the power button and the green indicator will turn on. PLAYING NOTE 1) Power-on default set vehicle to climbing mode. 2) For both TX and vehicle, green light ON indicates the climbing mode and red light ON indicates the fast running mode 3) Conventional bi-motor control with 2 joysticks. 4) The left trigger ring is for front swivel arm and the right trigger ring is for rear swivel arm 5) Pull both trigger rings towards yourself to unfold the arms; keep pulling the rings and Tarantula will stand up. Push the rings away from you to fold the arms up. 6) Press the rectangular red button to toggle between climbing and high-speed mode. Push both joysticks in the same direction to drive the vehicle straight back and forth to ensure good engagement of gears.) 7) Under high-speed mode, the vehicle cannot swivel arms for safety purposes. We will add sensors to the arms later so that high speed will be trigger only when the arms are pointing upwards. please change to climbing mode. Climbing up and down stairs The speed of standard climbing is 4.5 to 5 seconds per step and the speed of fast climbing is 2.7 to 3 seconds per step. Please refer to the movies from time to time and make sure you can fully understand the climbing method. For climbing up stairs, unfold the arms with the tip of rear arms slightly stand against the ground at around 5° to 10° to the horizontal. This will slightly lift up the rear of the vehicle. This is essential to avoid slipping down when climbing up steps. Make the Tarantula run forward and stand up before and touch the vertical wall of the 1st step with the track grasp on the edge of 1st step. Swivel the front arm by pulling the left trigger ring towards yourself. The front wheels and the jaw of vehicle will sit on the edge of the 1st step. Hold the trigger ring all the time to keep the Tarantula to climb. The difference between standard climbing and fast climbing is by controlling the time to push both joysticks. Please pay particular attention to the swivel angle of the front arms. For standard climbing, push and hold the joysticks only when the arms are pointing forward horizontal and release when the arms is vertical. For fast climbing, push the joysticks all the time to keep the track runs but release only when the swivel arm is pointing backward horizontal to vertical. For climbing down stairs, this can be done be swiveling the front arm only, on track movement is necessary. So keeping push the left ring away from you and all is done. Alternatively, you can just use track to run down the slope. Please review the movies thoroughly and practice to develop the climbing technique for demonstration purposes. You can climb up or down stairs with either front or rear side of the vehicle. However, it will be more stable to climbing with the front side. RECHARGING THE BATTERY After playing for approximately 5 to 10 minutes, the performance of your toy will decrease. It is time to charge your Battery Pack. Please follow the recharging instructions included with your Battery Pack and Charger. If the battery is warm, please allow up to twenty minutes for it to cool before recharging. OPERATIONAL TIPS AND HELPFUL HINTS -Make sure the battery door of the toy has bee…

Text truncated - open the document above for the full version.

PHOTOGRAPH OF THE PRODUCT FRONT VIEW OF THE PRODUCT REAR VIEW OF THE PRODUCT

FCC ID: LU9276210 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

LABEL LOCATION BOTTOM VIEW OF THE DEVICE WITH FCC ID LABEL FCC Label

PHOTOGRAPH OF THE PRODUCT INNER CIRCUIT TOP VIEW INNER CIRCUIT BOTTOM VIEW

FCC ID: LU9276210 Circuit Description The 49.86 (24.93 x 2)MHz crystal oscillator drives the base of Q3 the final/buffer amplifier. The modulation provided by IC. The output of Q3 has the matching network consisting of L2 and C18 that limit the harmonic content and effect the proper coupling of the antenna to the output stage. Antenna, Ground and Power Source The antenna consists of a 18.4cm long telescoping chrome over brass tubing. There is no external ground connection. The ground is only that of the printed circuit board. Electric current is supplied by a 9 Volt (“6F22” size battery x 1) primary battery

TARANTULA-TX0(FM)R1.sch-1 - Mon Jul 05 14:26:30 2004

香 港 標 準 及 檢 定 中 心 Hong Kong Standards and Testing Centre Date : 2004-07-28 TEST REPORT Page 1 of 18 No. : HM151908 This report shall not be reproduced unless with prior written approval from the Hong Kong Standards and Testing Centre. 香港新界大埔工業村大宏街10號 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] For full text of “Conditions of Issuance of Test Report”, please refer to overleaf or refer to the website of STC: www.hkstc.org (the section “Application and Quotation”). Applicant: MGA Entertainment (HK) Ltd. 9 th Floor, Tower 6, The Gateway, Harbour City, 9 Canton Road, Tsim Sha Tsui, Kowloon, Hong Kong Description of Samples: Model name: RF Car Model no.: 274995 Brand name: Tarantula FCC ID: LU9276210 Date Samples Received: 2004-07-12 Date Tested: 2004-07-26 Investigation Requested: FCC Part 15 Subpart C Conclusions: The submitted product COMPLIED with the requirements of Federal Communications Commission [FCC] Rules and Regulations Part 15. The tests were performed in accordance with the standards described above and on Section 2.2 in this Test Report. Remarks: ---- K C Lee, EMC for Chief Executive 香 港 標 準 及 檢 定 中 心 Hong Kong Standards and Testing Centre Date : 2004-07-28 TEST REPORT Page 2 of 18 No. : HM151908 香港新界大埔工業村大宏街10號 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] For full text of “Conditions of Issuance of Test Report”, please refer to overleaf or refer to the website of STC: www.hkstc.org (the section “Application and Quotation”). CONTENT: Cover Page 1 of 18 Content Page 2-3 of 18 1.0 General Details 1.1 Test Laboratory Page 4 of 18 1.2 Applicant Details Page 4 of 18 Applicant HKSTC Code Number for Applicant Manufacturer 1.3 Equipment Under Test [EUT] Page 5 of 18 Description of EUT operation 1.4 Date of Order Page 5 of 18 1.5 Submitted Samples Page 5 of 18 1.6 Test Duration Page 5 of 18 1.7 Country of Origin Page 5 of 18 1.8 Additional Information of EUT Page 6 of 18 2.0 Technical Details 2.1 Investigations Requested Page 7 of 18 2.2 Test Standards and Results Summary Page 7 of 18 3.0 Test Results 3.1 Emission Page 8-11 of 18 3.2 Bandwidth Measurement Page 12-13 of 18 香 港 標 準 及 檢 定 中 心 Hong Kong Standards and Testing Centre Date : 2004-07-28 TEST REPORT Page 3 of 18 No. : HM151908 香港新界大埔工業村大宏街10號 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] For full text of “Conditions of Issuance of Test Report”, please refer to overleaf or refer to the website of STC: www.hkstc.org (the section “Application and Quotation”). Appendix A List of Measurement Equipment Page 14 of 18 Appendix B Duty Cycle Correction During 100 msec Page 15-16 of 18 Appendix C Photographs Page 17-18 of 18 香 港 標 準 及 檢 定 中 心 Hong Kong Standards and Testing Centre Date : 2004-07-28 TEST REPORT Page 4 of 18 No. : HM151908 香港新界大埔工業村大宏街10號 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] For full text of “Conditions of Issuance of Test Report”, please refer to overleaf or refer to the website of STC: www.hkstc.org (the section “Application and Quotation”). 1.0 General Details 1.1 Test Laboratory The Hong Kong Standards and Testing Centre Ltd. EMC Laboratory 10 Dai Wang Street, Taipo Industrial Estate New Territories, Hong Kong 1.2 Applicant Details Applicant MGA Entertainment (HK) Ltd. 9 th Floor, Tower 6, The Gateway, Harbour City, 9 Canton Road, Tsim Sha Tsui, Kowloon, Hong Kong HKSTC Code Number for Applicant MGE001 Manufacturer Kin Yat Industrial Co. Ltd. 7/F, Galaxy Factory Building, 25-27 Luk Hop Street, San Po Kong, Kowloon, Hong Kong 香 港 標 準 及 檢 定 中 心 Hong Kong Standards and Testing Centre Date : 2004-07-28 TEST REPORT Page 5 of 18 No. : HM151908 香港新界大埔工業村大宏街10號 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] For full text of “Conditions of Issuance of Test Report”, please refer to overleaf or refer to the website of STC: www.hkstc.org (the section “Application and Quotation”). 1.3 Equipment Under Test [EUT] Description of Sample Model Name: RF Car Manufacturer: Kin Yat Industrial Co. Ltd. Brand Name: Tarantula Model Number: 274995 Input Voltage: 9Vd.c.(“6F22” size battery x 1) 1.3.1 Description of EUT Operation The Equipment Under Test (EUT) is a MGA Entertainment (HK) Ltd., RF Car. The transmitter is a 3 button transmitter. The EUT continues to transmit while button is being pressed, Modulation by IC. and type is pulse modulation. 1.4 Date of Order 2004-07-12 1.5 Submitted Sample(s): 1 Sample per model 1.6 Test Duration 2004-07-26 1.7 Country of Origin China 香 港 標 準 及 檢 定 中 心 Hong Kong Standards and Testing Centre Date : 2004-07-28 TEST REPORT Page 6 of 18 No. : HM151908 香港新界大埔工業村大宏街10號 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] For full text of “Conditions of Issuance of Test Report”, please refer to overleaf or refer to the website of STC: www.hkstc.org (the section “Application and Quotation”). 1.8 Additional Information of EUT Submitted Not Available User Manual Part List Circuit Diagram Printed Circuit Board [PCB] Layout Block diagram FCC ID Label 香 港 標 準 及 檢 定 中 心 Hong Kong Standards and Testing Centre Date : 2004-07-28 TEST REPORT Page 7 of 18 No. : HM151908 香港新界大埔工業村大宏街10號 10 Dai Wang Street, Taipo Industrial Estate, N.T., Hong Kong Tel: (852) 2666 1888 Fax: (852) 2664 4353 Homepage: www.hkstc.org E-mail: [email protected] For full text of “Conditions of Issuance of Test Report”, please refer to overleaf or refer to the website of STC: www.hkstc.org (the section “Application and Quotation”). …

Text truncated - open the document above for the full version.

TEST SET UP PHOTOGRAPH OF THE PRODUCT MEASUREMENT OF RADIATED EMISSION TEST SET UP