LU9276227RC Toy Transmitter

TEST SET UP PHOTOGRAPH OF THE PRODUCT MEASUREMENT OF RADIATED EMISSION TEST SET UP

Instruction Manual 41 0504-A-0 Note: Battery life varies depending on usage. An average charge should last approximately 20 minutes. The rechargeable battery should be charged by an adult. AGES 8+ Race the 27 MHz X-19 Infiltrator against the 49 MHz Sea Prowler 99 for awesome competitive racing action! Includes: - Shadow Shifter - Full-Function Handset & Antenna - Instruction Manual Requires (included in Bonus Pack only): - 1x 9.6V 700mAh NiCd Battery Pack - 4-hour Charger for 9.6V 700mAh NiCd Battery Pack - 1x 9V Battery Important: - After use, the Battery Pack may be hot. Allow it to cool for at least 20 minutes before recharging. - If the Battery Pack shows signs of leakage or erosion, do not recharge; replace it immediately. - Do not disassemble the Battery Pack. - If the battery pack or charging unit becomes wet, dry thoroughly before recharging. - Do not use any other rechargeable battery except for the standard 9.6V NiCd Battery Pack that was intended solely for use with the product. - The Battery Charger used with the toy is to be regularly examined for damage to the plug, enclosure and other parts. In the event of such damage, the toy must not be used with this battery charger until the damage has been repaired. - The product is not intended for children inder 3 years old. - The product must only be used with the recommended battery charger. - The battery charger is not a toy. Before you can experience all the fun and excitement of using your toy, you must charge your Battery Pack. Follow these simple instructions for your initial charge-up and all recharges thereafter. FCC NOTICE: This equipment has been tested and found to comply with limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, this is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. IMPORTANT NOTICE Modifications not authorized by the manufacturer may void user's authority to operate this device. Emissions or interference of surrounding electronic equipment may affect operating performance. CAUTION: - Do not use rechargeable batteries for the Remote Control Handset. - Not suitable for children under 3 years. - May contain small parts. SPECIFICATIONS STEP 1: CHARGING THE BATTERY 1. Connect the Battery Charger Connector into the 9.6V NiCd Rechargeable Battery Pack. 2. Plug the Battery Charger into a standard wall 120V outlet (see Fig.1). 3. Allow the Battery Pack to charge for 4 hours. 4. Disconnect the Battery Pack from the Battery Charger and remove the Battery Charger from the wall outlet. It should feel warm. Fig.1 9.6 V Charger Battery Charger Battery Pack Run silent and run fast with Shadow Shifter -- the dual-mode R/C watercraft! This amazingly fast and sleek ship travels across the water at an incredible speed and, with a push of a button on the remote, it transforms from hyper-speed mode to stealth mode, so no one will hear you! This transformable ship is the ultimate in water R/C, they'll never even know you're coming! TM The preferred method of contact for Customer Service is through our e-mail contact form at www.mgae.com TM TM & © MGA Entertainment, Inc. SHADOW SHIFTER™ and all related logos, names, characters and distinctive likenesses are the exclusive property of MGA Entertainment. 16730 Schoenborn Street North Hills, CA 91343 USA (800) 222-4685 Printed in China.

2 3 STEP 4 : RECHARGING THE BATTERY STEP 2 : INSTALLATION OF BATTERIES OPERATIONAL TIPS AND HELPFUL HINTS TROUBLE SHOOTING SAFETY BATTERY PRECAUTIONS Remote Controller: 1. Switch the power to the "OFF" position. 2. Unscrew and remove the battery compartment cover, located on the back of the handset, with a Phillips screwdriver (see fig. 2). 3. Insert 1 x 9V Alkaline battery in the proper direction as indicated inside the battery compartment (see fig. 2). 4. Put the battery cover back on & tighten the screw securely. 5. Switch the power to the "ON" position. Craft: 1. Check that the power indicator at the top of the ship is "OFF." If not, push the power ON/OFF button once to turn off the ship. 2. Unscrew and remove the battery door at the back of the craft (see fig. 3). 3. Plug a fully charged 9.6V NiCd Battery Pack (see fig.3.) 4. Put the battery door back on & lock it securely. 5. Press the power button and the indicator will turn on. STEP 3: USING YOUR SHADOW SHIFTER 1. Screw the telescopic antenna into the opening at the top of the Remote Controller and slowly stretch the antenna to full length. 2. Switch Remote Controller "ON" and the power indicator will light up (see fig. 4). 3. Carefully put the craft on a clear water surface. 4. Hold the ship hull and press the power ON/OFF button at the top of the craft, the indicator will turn on (see fig. 5). 5. Press the left and right buttons to transform the ship between High-Speed and Stealth Modes (see fig. 4). The craft will run at turbo speed only when the main hull is transformed to its highest position (see figs. 6 & 7). 6. Use the Left & Right control sticks to make the craft run FORWARD, LEFT, RIGHT and BACKWARD. The craft will not go straight BACKWARD for balancing purposes (see fig. 4). 7. Make sure to power off the craft before taking the craft out of water to AVOID QUICK SPINNING PROPELLERS. 8. Please lift and hold the ship sideways at different orientations to allow the water to drain for at least 15 seconds. 9. Fully retract the antenna and turn the handset "OFF" after playing. After playing for approximately 20 minutes, the performance of your toy will decrease. It is time to charge your Battery Pack. Please follow the recharging instructions included with your Battery Pack and Charger. If the battery is warm, please allow up to twenty minutes for it to cool before recharging. - Stretch and retract the antenna slowly and avoid using brute force. - Please make sure the handset is turned "ON" before turning the craft "ON" or "OFF." - Make sure the battery door of the craft has screwed shut securely before playing. - The craft has a built-in smart sensor and it can operate only on water. - Make sure to turn the craft "OFF" before taking it out of the water. - If the craft is getting too far away from you, the Automatic Retrieval System (ARS) will transform the craft to Stealth Mode and navigate in a circular path. Move the handset closer to the craft to re-establish signal connection. - This toy is designed to run on fresh water with little current, please do not play on the sea. - Do not operate during thunderstorms. - When your toy starts to lose power, it may experience loss of functions or performance. If this happens, simply recharge your Battery Pack again and/or replace the Handset battery. - The toy is operated by radio waves. It is possible the unit may not perform properly due to interference from nearby devices such as a cordless phone, hair dryer, radio, walkie-talkie or other radio-controlled toys. - Avoid sand and snow when operating your toy. - Do not submerge the toy or the handset in water. - Always select a safe place to play. - Keep fingers, hair and loose clothing away from the propellers while the vehicle is switched "ON." - Please drain the water and clean the toy with a clean, dry cloth after playing. - If the toy or the battery is low on power, the craft will stop running. - Do not get your rechargeable battery wet. If you do, dry it immediately. 1. If your toy responds slowly or fails to operate: - Make sure the batteries in both the Handset and toy are installed properly. - Recharge your Battery Pack and/or replace the Handset battery. - Make sure both the toy and the handset are turned "ON." - Make sure the Battery Contacts have not become dirty. If they have, simply brush them with a dry cloth. - Move the remote control handset closer to your toy to determine the best communication between the remote handset and the toy. 2. Upon extensive playing, the protective circuitry may shut down the craft automatically to avoid overheating. It is recommended to allow the craft to cool down for at least 20 minutes before restarting. In case you really need to control the craft back, to avoid being washed away, before resting, please restart the homing signal after one minute. - Non-rechargeable batteries are not to be recharged. - Rechargeable batteries are to be removed from the toy before being charged. - Rechargeable batteries are only to be charged under adult supervision. - Different types of batteries or new and used batteries are not to be mixed. - Only batteries of the same or equivalent type as recommended are to be used. - Batteries are to be inserted with the correct polarity. - Exhausted batteries are to be removed from the toy. - The supply terminals are not to be short-circuited. - Do not dispose of the batteries in fire; batteries may leak or explode. - Batteries should be replaced by an adult. - Use alkaline batteries for better performance. - When not in use for an extended time, remove batteries to prevent possible leakage. IMPORTANT! TOYS INTENDED TO BE USED IN WATER ARE TO BE OPERATED IN WATER ONLY WHEN FULLY ASSEMBLED IN ACCORDANCE WITH THE INSTRUCTIONS. Fig. 2 Fig. 3 Fig. 4 Fig. 5 Fig. 6Fig. 7 Stealth Mode High-Speed Mode Power LED Power LED High- Speed Mode Stealth Mode Power ON/OFF Power ON/OFF 6LR61 006P 9V 6LR61 006P 9V

PHOTOGRAPH OF THE PRODUCT FRONT VIEW OF THE PRODUCT REAR VIEW OF THE PRODUCT

FCC ID: LU9276227 MADE IN CHINA This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

LABEL LOCATION BOTTOM VIEW OF THE DEVICE WITH FCC ID LABEL

PHOTOGRAPH OF THE PRODUCT INNER CIRCUIT TOP VIEW INNER CIRCUIT BOTTOM VIEW

FCC ID: LU9276227 Circuit Description The 27.145MHz crystal oscillator drives the base of Q1 the final/buffer amplifier. The modulation provided by IC. The output of Q1 has the matching network consisting of L2 and C5 that limit the harmonic content and effect the proper coupling of the antenna to the output stage. Antenna, Ground and Power Source The antenna consists of a 41cm long metal antenna. There is no external ground connection. The ground is only that of the printed circuit board. Electric current is supplied by a 9 Volt (“6F22” size battery x 1) primary battery

Date: 2004-05-28 TEST REPORT Page 1 of 19 No.: HM150908 This report shall not be reproduced unless with prior written approval from the Hong Kong Standards and Testing Centre. Applicant: MGA Entertainment (HK) Ltd. Description of Samples: Model name: Stealth Ship (27MHz) Model no.: 276227 Brand name: N/A FCC ID: LU9276227 Date Samples Received: 2004-04-28 Date Tested: 2004-05-11 to 2004-05-27 Investigation Requested: FCC Part 15 Subpart C Conclusions: See the attached sheets for details Remarks: ---- K C Lee, EMC for Chief Executive Date: 2004-05-28 TEST REPORT Page 2 of 19 No.: HM150908 CONTENT: Cover Page 1 of 19 Content Page 2-3 of 19 Conclusions Page 4 of 19 1.0 General Details 1.1 Test Laboratory Page 5 of 19 1.2 Applicant Details Page 5 of 19 Applicant HKSTC Code Number for Applicant Manufacturer 1.3 Equipment Under Test [EUT] Page 6 of 19 Description of EUT operation 1.4 Date of Order Page 6 of 19 1.5 Submitted Samples Page 6 of 19 1.6 Test Duration Page 6 of 19 1.7 Country of Origin Page 6 of 19 1.8 Additional Information of EUT Page 7 of 19 2.0 Technical Details 2.1 Investigations Requested Page 8 of 19 2.2 Test Standards and Results Summary Page 8 of 19 3.0 Test Results 3.1 Emission Page 9-12 of 19 3.2 Bandwidth Measurement Page 13-14 of 19 Date: 2004-05-28 TEST REPORT Page 3 of 19 No.: HM150908 Appendix A List of Measurement Equipment Page 15 of 19 Appendix B Duty Cycle Correction During 100 msec Page 16-17 of 19 Appendix C Photographs Page 18-19 of 19 Date: 2004-05-28 TEST REPORT Page 4 of 19 No.: HM150908 CONCLUSIONS The submitted product was deemed to have COMPLIED with the requirements of Federal Communications Commission [FCC] Rules and Regulations Part 15. The tests were performed in accordance with the standards described above and on Section 2.2 in this Test Report. Date: 2004-05-28 TEST REPORT Page 5 of 19 No.: HM150908 1.0 General Details 1.1 Test Laboratory The Hong Kong Standards and Testing Centre Ltd. EMC Laboratory 10 Dai Wang Street, Taipo Industrial Estate New Territories, Hong Kong Telephone: 852 2666 1888 Fax: 852 2664 4353 1.2 Applicant Details Applicant MGA Entertainment (HK) Ltd. 9 th Floor, Tower 6, The Gateway, Harbour City, 9 Canton Road, Tsimshatsui, Kowloon, Hong Kong. HKSTC Code Number for Applicant MGE001 Manufacturer N/A Date: 2004-05-28 TEST REPORT Page 6 of 19 No.: HM150908 1.3 Equipment Under Test [EUT] Description of Sample Model Name: Stealth Ship (27MHz) Manufacturer: N/A Brand Name: N/A Model Number: 276227 Input Voltage: 9Vd.c (“6F22” size battery x 1) 1.3.1 Description of EUT Operation The Equipment Under Test (EUT) is an MGA Entertainment (HK) Ltd., Stealth Ship (27MHz). The transmitter is a 2 button with 2 joystick transmitter. The EUT continues to transmit while button is being pressed, Modulation by IC. and type is pulse modulation. 1.4 Date of Order 2004-04-28 1.5 Submitted Sample(s): 3 Samples per model 1.6 Test Duration 2004-05-11 to 2004-05-27 1.7 Country of Origin China Date: 2004-05-28 TEST REPORT Page 7 of 19 No.: HM150908 1.8 Additional Information of EUT Submitted Not Available User Manual Part List Circuit Diagram Printed Circuit Board [PCB] Layout Block diagram FCC ID Label Date: 2004-05-28 TEST REPORT Page 8 of 19 No.: HM150908 2.0 Technical Details 2.1 Investigations Requested Perform ElectroMagnetic Interference measurement in accordance with FCC 47CFR [Codes of Federal Regulations] Part 15 and ANSI C63.4:2003 for FCC Certification. 2.2 Test Standards and Results Summary Tables EMISSION Results Summary Test Condition Test Requirement Test Method Class / Test Result Severity Pass Failed N/A Field Strength of Fundamental Emissions & Spurious Emissions FCC 47CFR 15.227 ANSI C63.4:2003 N/A Radiated Emissions, 30MHz to 1GHz FCC 47CFR 15.209 ANSI C63.4:2003 Class B Conducted Emissions on AC, 0.15MHz to 30MHz FCC 47CFR 15.207 ANSI C63.4:2003 Class B Note: N/A - Not Applicable Date: 2004-05-28 TEST REPORT Page 9 of 19 No.: HM150908 3.0 Test Results 3.1 Emission 3.1.1 Radiated Emissions (30 – 1000MHz) Test Requirement: FCC 47CFR 15.227 Test Method: ANSI C63.4:2003 Test Date: 2004-05-25 Mode of Operation: On mode Test Method: The sample was placed 0.8m above the ground plane on the OATS *. Measurements in both horizontal and vertical polarities were performed. During the test, each emission was maximized by: having the EUT continuously working, investigated all operating modes, rotated about all 3 axis (X, Y & Z) and considered typical configuration to obtain worst position, manipulating interconnecting cables, rotating turntable, varying antenna height from 1m to 4m in both horizontal and vertical polarizations. The emissions worst-case are shown in Test Results of the following pages. *: OATS [Open Area Test Site] located at HKSTC with a metal ground plane filed with the FCC pursuant to section 2.948 of the FCC rules, with Registration Number: 90657. Test Setup: EUT Pre-Amplifier Distance = 3m Receiver Turn Table Computer Ground Plane Date: 2004-05-28 TEST REPORT Page 10 of 19 No.: HM150908 Limits for Field Strength of Fundamental Emissions [FCC 47CFR 15.227]: Frequency Range of Fundamental Field Strength of Fundamental Emission [Peak] Field Strength of Fundamental Emission [Average] [MHz] [μV/m] [μV/m] 26.96-27.28 100,000 10,000 Results: FrequencyCorrectionLimit @3mE-Field FactorPolarity MHzdBμV/mμV/m 27.1547.9021.969.83,090.3100,000Vertical μ V/mdB μ V/m Field Strength dB μ V/m Field Strength of Fundamental Emissions Peak Value Measured Level @3m Field Strength FrequencyAdjusted byCorrectionLimit @3mE-Field Duty CycleFactorPolarity MHzdBdB μ V/m μ V/m 27.1538.3-9.621.960.21,023.310,000Vertical Field Strength of Fundamental Emissions Average Measured Level @3m Field Strength μV/mdBμV/m Field Strength dBμV/m According to FCC 47CFR15.35, the limit on the radio frequency emissions as measured using instrumentation with a peak detector function, corresponding to 20dB above the maximum permitted average limit for the frequency being…

Text truncated - open the document above for the full version.

Close From: [email protected] [SMTP:[email protected]] To: [email protected] Cc: [email protected] Subject: RE: HKSTC HM150908 report FCC ID: LU9276227 MET: 15672 Sent: 6/24/2004 12:09 AM Importance: Normal Hi Alvin, Q1. The sample is transmitter, product name is Stealth Ship (27MHz). Q2. Antenna is two years Q3. Please see attached file for the update test report. Hi Alvin, would you help me check the LU9277880A & LU9276227 status. (My client is urgent to get the cert.) Thanks Best Regards Alice -----Original Message----- From: [email protected] [mailto:[email protected]] Sent: Tuesday, June 22, 2004 5:29 AM To: [email protected] Cc: [email protected] Subject: HKSTC HM150908 report FCC ID: LU9276227 MET: 15672 Hi Alice, I have some comments about the above test report: 1) The description does not match the equipment. 2) Please check the calibration date on Asset EM194 Biconilog Antenna. 3) In the table on page 11/19, for the first two rows the limits should be 100uV/m. I look forward to your response. Thank you for using MET Laboratories TCB services. Best Regards, Alvin Ilarina EMC/RF Laboratory Manager MET Laboratories, Inc. 4855 Patrick Henry Dr. Bldg #6 Santa Clara, CA 95054 U.S.A. w:408-213-2671 c:650-544-9070 [email protected] www.metlabs.com HM150908 _r1 test report.pdf

TEST SET UP PHOTOGRAPH OF THE PRODUCT MEASUREMENT OF RADIATED EMISSION TEST SET UP

TEST SET UP PHOTOGRAPH OF THE PRODUCT MEASUREMENT OF RADIATED EMISSION TEST SET UP