LXP-VIM223Low Power Transmitter < 1.705 MHz

FCC ID: LXP-VIM223 (IC: 2298A-VIM223) Report No. M040411_Cert_Immobiliser This Laboratory is accredited by the National Association of Testing Authorities, Australia. The tests reported herein have been performed in accordance with its terms of accreditation for FCC Part 15.This document shall not be reproduced, except in full. EMC Technologies Report No. M040411_Cert_Immobiliser Appendix I – User Manual Knowing your vehicle 8 3 123456789 10 Your vehicle is equipped with anelectronic engine immobilizer systemto reduce the risk of unauthorizedvehicle use.Your immobilizer system is com-prised of a small transponder in theignition key, and antenna coil in thekey cylinder and Immobilizer ControlUnit (or Smartra Unit).With this system, whenever youinsert your ignition key into the igni-tion switch and turn it to ON, theantenna coil in the ignition switchreceives a signal from the transpon-der in the ignition key and then sendsthe signal to the ECU (EngineControl Unit).The ECU checks the signal whetherthe ignition key is valid.If the key is determined to be valid,the engine will start.If the key is determined to be invalid,the engine will not start. To deactivate the immobilizer sys-tem:Insert the ignition key into the keycylinder and turn it to the ON posi-tion.To activate the immobilizer sys-tem:Turn the ignition key to the OFF posi-tion. The immobilizer system acti-vates automatically. Without a validignition key for your vehicle, theengine will not start. This device complies with Part 15of the FCC rules. Operation is sub- ject to the following two conditions:1. This device may not cause harm- ful interference, and 2. This device must accept any inter- ference received, including inter-ference that may cause undesiredoperation. IMMOBILIZER SYSTEM (IF EQUIPPED) CAUTION The transponder in your ignitionkey is an important part of theimmobilizer system. It is designed to give years of trou-blefree service, however youshould avoid exposure to mois-ture, static electricity and roughhandling. Immobilizer system malfunction could occur. CAUTION Do not change, alter or adjustthe immobilizer system becauseit could cause the immobilizersystem to malfunction andshould only be serviced by anauthorized Kia dealer.Malfunctions caused by improp-er alterations, adjustments ormodifications to the immobilizersystem are not covered by yourvehicle manufacturer warranty. CAUTION Changes or modifications notexpressly approved by the partyresponsible for compliancecould void the user's authorityto operate the equipment. KM USA ~3-56.qxd 9/16/04 3:18 PM Page 8

Response to TCB findings.txt From: "Donna" <[email protected]> To: <[email protected]> Subject: FW: FCC ID: LXP-VIM223 Robert Bosch TCB findings Date: Sunday, October 03, 2004 9:13 PM Hi Barry, Please refer to details below regarding the current label material and proposed labelling changes. When the labelling method is changed next year - Do Bosch need to advise prior to this change or advise the FCC of the change, etc? Thanks for your assistance Regards Donna Cleary EMC Technologies Pty Ltd -----Original Message----- From: Altis Peter (RBAU-EB/PJM2) * [mailto:[email protected]] Sent: Monday, 4 October 2004 10:41 AM To: Donna Cc: [email protected] Subject: RE: FCC ID: LXP-VIM223 Robert Bosch TCB findings Importance: High Hi Donna, the material is a polypropylene film material, 0.08mm thick. It has passed all adhesion trials and is considered by RB and HMC as being a permanent label, suitable for its application and life of the part. Please ask Barry to consider/understand the part is mounted inside the car in the coulomb shroud enclosure and is not subjected to under bonnet conditions. Furthermore to aid our hi volume production early next year we will be moving to a laser etched 'label' such as attached. (concept only) Regards, Peter -----Original Message----- From: Donna [mailto:[email protected]] Sent: Monday, 4 October 2004 9:34 AM To: Altis Peter (RBAU-EB/PJM2) * Subject: FW: FCC ID: LXP-VIM223 Robert Bosch TCB findings Hi Peter, Please provide the required details. Thanks Donna Cleary EMC Technologies Pty Ltd -----Original Message----- From: Curtis-Straus Certification Dept. [mailto:[email protected]] Sent: Friday, 1 October 2004 3:46 AM To: Donna Cleary Subject: FCC ID: LXP-VIM223 Robert Bosch TCB findings Page 1 Response to TCB findings.txt Hi Donna, This issue was found during our review of the application: 1. Please supply details of the label material. Thank you. Best regards Barry C. Quinlan Certification Manager Curtis-Straus TCB This e-mail was scanned for viruses using BitDefender. This e-mail was scanned for viruses using BitDefender. Page 2

FCC ID: LXP-VIM223 (IC: 2298A-VIM223) Report No. M040411_Cert_Immobiliser EMC Technologies Pty Ltd – 57 Assembly Drive, Tullamarine VIC 3043 Australia www.emctech.com.au EMC Technologies Report Number: M040411_Cert_Immobiliser APPENDIX B1 – Test Sample Photographs (external) FCC ID: LXP-VIM223 (IC: 2298A-VIM223) Report No. M040411_Cert_Immobiliser EMC Technologies Pty Ltd – 57 Assembly Drive, Tullamarine VIC 3043 Australia www.emctech.com.au APPENDIX B1 – Test Sample Photographs (external)

FCC ID: LXP-VIM223 (IC: 2298A-VIM223) Report No. M040411_Cert_Immobiliser EMC Technologies Pty Ltd – 57 Assembly Drive, Tullamarine VIC 3043 Australia www.emctech.com.au EMC Technologies Report Number: M040411_Cert_Immobiliser APPENDIX B3 – Test Sample Internal Photographs FCC ID: LXP-VIM223 (IC: 2298A-VIM223) Report No. M040411_Cert_Immobiliser EMC Technologies Pty Ltd – 57 Assembly Drive, Tullamarine VIC 3043 Australia www.emctech.com.au APPENDIX B3 – Test Sample Internal Photographs

EMI TEST REPORT for CERTIFICATION to FCC PART 15.209 & RSS-210 FCC ID: LXP-VIM223 Industry Canada ID: 2298A-VIM223 Test Sample: XD Smartra Immobiliser Tested for: Robert Bosch Australia Report Number: M040411_Cert_Immobiliser Issue Date: 16 th August 2004 EMC Technologies Pty Ltd reports apply only to the specific samples tested under stated test conditions. It is the manufacturer’s responsibility to assure that additional production units of this model are manufactured with identical electrical and mechanical components. EMC Technologies Pty Ltd shall have no liability for any deductions, inferences or generalisations drawn by the client or others from EMC Technologies Pty Ltd issued reports. This report shall not be used to claim, constitute or imply product endorsement by EMC Technologies Pty Ltd. The tests, calibrations or measurements covered by this document have been performed in accordance with NATA requirements which include the requirements of ISO/IEC 17025 and are traceable to national standards of measurement. This document shall not be reproduced, except in full. NATA Accredited Laboratory Number: 5292 EMC Technologies Pty Ltd ABN 82 057 105 549 57 Assembly Drive Tullamarine Victoria Australia 3043 Ph: + 613 9335 3333 Fax: + 613 9338 9260 email: [email protected] FCC ID: LXP-VIM223 (IC: 2298A-VIM223) Report No. M040411_Cert_Immobiliser Page 2 of 10 This Laboratory is accredited by the National Association of Testing Authorities, Australia. The tests reported herein have been performed in accordance with its terms of accreditation for FCC Part 15.This document shall not be reproduced, except in full. EMI TEST REPORT FOR CERTIFICATION to FCC Part 15.209 & RSS-210 EMC Technologies Report No. M040411_Cert_Immobiliser Issue Date: 16 th August 2004 CONTENTS 1.0 INTRODUCTION 2.0 GENERAL INFORMATION 3.0 CONDUCTED EMI MEASUREMENTS 4.0 RADIATED EMI MEASUREMENTS 5.0 ANTENNA REQUIREMENT 6.0 COMPLIANCE STATEMENT APPENDIX A: MEASUREMENT INSTRUMENT DETAILS APPENDIX B: TEST SAMPLE PHOTOGRAPHS APPENDIX C: OPERATIONAL DESCRIPTIONS APPENDIX D: TEST SAMPLE BLOCK DIAGRAM APPENDIX E: TEST SAMPLE SCHEMATIC APPENDIX F: TEST SAMPLE PCB LAYOUT APPENDIX G: FCC ID LABELLING APPENDIX H: GRAPHS of EMI MEASUREMENTS APPENDIX I: USER MANUAL FCC ID: LXP-VIM223 (IC: 2298A-VIM223) Report No. M040411_Cert_Immobiliser Page 3 of 10 This Laboratory is accredited by the National Association of Testing Authorities, Australia. The tests reported herein have been performed in accordance with its terms of accreditation for FCC Part 15.This document shall not be reproduced, except in full. EMI TEST REPORT FOR CERTIFICATION to FCC PART 15.209 & RSS-210 Report Number: M040411_Cert_Immobiliser Test Sample: XD Smartra Immobiliser Manufacturer: Robert Bosch (Australia) Pty Ltd FCC ID: LXP-VIM223 Industry Canada ID: 2298A-VIM223 Equipment Type: Intentional Radiator Tested for: Robert Bosch (Australia) Pty Ltd Address: Cnr Centre & McNaughton Roads, Clayton VIC 3168, Australia Phone: + 61 3 9541 5555 Fax: + 61 3 9544 1137 Responsible Party: Peter Altis Test Standards: FCC Part 15, Subpart C – Intentional Radiators FCC Part 15.209: Radiated Emission Limits, General Requirements. ANSI C63.4 – 2003 OET Bulletin No. 65 RSS-210 Issue 5 Low Power Licence-Exempt RadioCommunication Devices. 6.3: Restricted Bands and Unwanted Emission Frequencies Test Date: 6 th April 2004 Test Officers: Chieu Huynh Kevin Hansen B.Eng (Hons) Electronics Attestation: I hereby certify that the device(s) described herein were tested as described in this report and that the data included is that which was obtained during such testing. Authorised Signatory: Chris Zombolas Technical Director EMC Technologies Pty Ltd FCC ID: LXP-VIM223 (IC: 2298A-VIM223) Report No. M040411_Cert_Immobiliser Page 4 of 10 This Laboratory is accredited by the National Association of Testing Authorities, Australia. The tests reported herein have been performed in accordance with its terms of accreditation for FCC Part 15.This document shall not be reproduced, except in full. EMI TEST REPORT FOR CERTIFICATION to FCC PART 15.209 & RSS-210 1.0 INTRODUCTION This report details the results of EMI tests and measurements performed on the XD Smartra Immobiliser. Test results and procedures were performed in accordance with the following Federal Communications Commission (FCC) standards/regulations: 47 CFR, Part 15, Subpart C: Rules for intentional radiators (particularly section 15.209) Section 15.203: Antenna requirements Section 15.205: Restricted bands of operation Section 15.207: Conducted Emission Limits Section 15.209: Radiated Emission Limits, General Requirements The test sample complied with the requirements of 47 CFR, Part 15 Subpart C - Section 15.209: Radiated Emission Limits, General Requirements The test sample also complied with the Industry Canada RSS-210 issue 5 (Low Power Licence- Exempt Radiocommunication Devices (All Frequency Bands)) clause 6.3: Restricted Bands and Unwanted Emission Frequencies. 1.1 Summary of Results FCC Part 15, Subpart C Clauses Industry Canada RSS-210 Clauses Test Performed Result 15.203 5.5 Antenna Requirement Not Applicable 15.205 6.3 Operation in Restricted Band Complies 15.207 6.6 Conducted Emissions Not Applicable 15.209 6.3 Radiated Emissions Complies The measurement procedure used was in accordance with ANSI C63.4-2003 and OET Bulletin No. 65. The instrumentation conformed to the requirements of ANSI C63.2-1996. 1.2 Modifications by EMC Technologies No modifications were required. FCC ID: LXP-VIM223 (IC: 2298A-VIM223) Report No. M040411_Cert_Immobiliser Page 5 of 10 This Laboratory is accredited by the National Association of Testing Authorities, Australia. The tests reported herein have been performed in accordance with its terms of accreditation for FCC Part 15.This document shall not be reproduced, except in full. 2.0 GENERAL INFORMATION (Information supplied by the Client) 2.1 Product Details Test Sample: XD Smartra Immobiliser FCC I…

Text truncated - open the document above for the full version.

FCC ID: LXP-VIM223 (IC: 2298A-VIM223) Report No. M040411_Cert_Immobiliser This Laboratory is accredited by the National Association of Testing Authorities, Australia. The tests reported herein have been performed in accordance with its terms of accreditation for FCC Part 15.This document shall not be reproduced, except in full. EMC Technologies Report No. M040411_Cert_Immobiliser Appendix A – Measurement instrumentation FCC ID: LXP-VIM223 (IC: 2298A-VIM223) Report No. M040411_Cert_Immobiliser EMC Technologies Pty Ltd – 57 Assembly Drive, Tullamarine VIC 3043 Australia www.emctech.com.au APPENDIX A MEASUREMENT INSTRUMENTATION DETAILS EQUIPMENT TYPE MAKE/MODEL SERIAL NUMBER LAST CAL. DD/MM/YY DUE DATE DD/MM/YY CAL. INTERVAL EMI RECEIVER HP 8574B System Components 26/09/03 26/09/04 1 YEAR *2 EMI RECEIVER HP 8546A, Sn: 3549A00290 13/02/04 13/02/05 1 YEAR *2 EMI RECEIVER Rohde & Schwarz, Model ESIB40 SN 1088 7490, 20 Hz – 40 GHz 20/07/03 20/07/04 1 YEAR *3 ANTENNAS EMCO 93110B BICONICAL 20/08/03 20/08/04 1 YEAR *1 20 - 300 MHz Sn. 9804-3092 EMCO 93146A LOG PERIODIC 19/07/03 19/07/04 1 YEAR *1 200 -1000MHz Sn. 5033 EMCO 3115 DOUBLE RIDGED HORN 1 - 18 GHz Sn: 8908-3282 29/01/03 29/01/06 3 YEAR *1 EMCO 6502 ACTIVE LOOP ANTENNA 0.009 – 30 MHz Sn: 9609-3065 04/07/03 04/07/04 1 YEAR *1 Note *1. In-house calibration. Refer to Quality Manual. Note *2. NATA calibration by Agilent Technologies (Aust) Pty Ltd Note *3. NATA calibration by Rohde & Schwarz TEST SITES Shielded Room Test Laboratory Melbourne 11m x 8m x 4m Chamber-semi-anechoic 8.8m x 5.8m x 3.1m Test Chamber 3.4m x 6.1m x 2.5m Test Chamber 3.4m x 7.3m x 7.5m Test Chamber Feb 03 N/A N/A N/A Feb 04 N/A N/A N/A 1 Year *1 N/A N/A N/A Open Area Test Site Melbourne 3/10 Metre site. 1-4 metre antenna mast. 1.2 metre/400 kg Turntable. (Situated at Lerderderg Gorge, near Bacchus Marsh, Victoria) 11/02/04 11/02/05 1 Year *1 Note *1. In-house calibration. Refer to Quality Manual.

FCC ID: LXP-VIM223 (IC: 2298A-VIM223) Report No. M040411_Cert_Immobiliser This Laboratory is accredited by the National Association of Testing Authorities, Australia. The tests reported herein have been performed in accordance with its terms of accreditation for FCC Part 15.This document shall not be reproduced, except in full. EMC Technologies Report No. M040411_Cert_Immobiliser Appendix H – Graphs of EMI Measurement EMC Technologies Pty. Ltd. - Global Product Certification Job No:m040612 Test Date: 16-06-04 GRAPH No. 1 r:\PCF\m040411i_1.PCF Melbourne- 57 Assembly Drv Tullamarine, 3043, Vic, Australia Ph+(613) 9335 3333 Fax+(613) 9338 9260Sydney---- 16,6 Gladstone Rd Castle Hill, 2154, NSW, Australia Ph+(612) 9899 4599 Fax+(612) 9899 4019Robert Bosch (Australia) Pty Ltd XD Smartra - 125kHz Immobiliser Old Variant - Tx ON Antenna Parallel Radiated Emissions (dBuV/m) m040411rm040411r # = Ambient Limits: Legend: Source: _ FCC15209 FCC PART 15.209 3mtr LMTS __ Ambients __ Emissions 28 29 30 18 15 16 17 31 Ver 5.5 Build 93radiated emissions site 2 lerderderg t:6502_E c1:C1700804 c2:NONE p:NONE a:NONESite ID: OATS1,Lerderderg Gorge Rd, Bacchus Marsh, VIC Test Officer:Chieu Huynh Peaks:No Freq Peak Qp Val FCC15209 dL1 (MHz) (dBuV/m) (dBuV/m) (dB) 1 0.125 74.9 74.9 105.5 -30.6 Frequency (MHz) .1 1 10 .009 30.5 10 20 30 40 50 60 70 80 90 100 110 120 130 v ^ 1 ~ # # # # # # # # # # # # # # # # # # # EMC Technologies Pty. Ltd. - Global Product Certification Job No:m040612 Test Date: 16-06-04 GRAPH No. 2 r:\PCF\m040411i_2.PCF Melbourne- 57 Assembly Drv Tullamarine, 3043, Vic, Australia Ph+(613) 9335 3333 Fax+(613) 9338 9260Sydney---- 16,6 Gladstone Rd Castle Hill, 2154, NSW, Australia Ph+(612) 9899 4599 Fax+(612) 9899 4019Robert Bosch (Australia) Pty Ltd XD Smartra - 125kHz Immobiliser Old Variant - Tx ON Antenna Perpendicular Radiated Emissions (dBuV/m) m040411rm040411r # = Ambient Limits: Legend: Source: _ FCC15209 FCC PART 15.209 3mtr LMTS __ Ambients __ Emissions 1 13 3 4 20 21 22 23 Ver 5.5 Build 93radiated emissions site 2 lerderderg t:6502_E c1:C1700804 c2:NONE p:NONE a:NONESite ID: OATS1,Lerderderg Gorge Rd, Bacchus Marsh, VIC Test Officer:Chieu Huynh Peaks:No Freq Peak Qp Val FCC15209 dL1 (MHz) (dBuV/m) (dBuV/m) (dB) 1 0.125 69.5 69.5 105.5 -36.0 Frequency (MHz) .1 1 10 .009 30.5 10 20 30 40 50 60 70 80 90 100 110 120 130 v ^ 1 ~ # # # # # # # # # # # # # # # # # # # EMC Technologies Pty. Ltd. - Global Product Certification Job No:m040411 Test Date: 8-04-04 GRAPH No. 3 r:\PCF\m040411i_3.PCF Melbourne- 57 Assembly Drv Tullamarine, 3043, Vic, Australia Ph+(613) 9335 3333 Fax+(613) 9338 9260Sydney---- 16,6 Gladstone Rd Castle Hill, 2154, NSW, Australia Ph+(612) 9899 4599 Fax+(612) 9899 4019Robert Bosch (Australia) Pty Ltd XD Smartra - 125kHz Immobiliser Old Variant - Tx Idle Antenna Parallel Radiated Emissions (dBuV/m) m040411rm040411r # = Ambient Limits: Legend: Source: _ FCC15209 FCC PART 15.209 3mtr LMTS __ Ambients __ Emissions 5 29 30 8 28 14 7 31 Ver 5.5 Build 93radiated emissions site 2 lerderderg t:6502_E c1:C1700804 c2:NONE p:NONE a:NONESite ID: OATS2,Lerderderg Gorge Rd, Bacchus Marsh, VIC Test Officer:Kevin Hansen Frequency (MHz) .1 1 10 .009 30.5 10 20 30 40 50 60 70 80 90 100 110 120 130 # # # # # # # # # # # # # # # # # # # EMC Technologies Pty. Ltd. - Global Product Certification Job No:m040411 Test Date: 8-04-04 GRAPH No. 4 r:\PCF\m040411i_4.PCF Melbourne- 57 Assembly Drv Tullamarine, 3043, Vic, Australia Ph+(613) 9335 3333 Fax+(613) 9338 9260Sydney---- 16,6 Gladstone Rd Castle Hill, 2154, NSW, Australia Ph+(612) 9899 4599 Fax+(612) 9899 4019Robert Bosch (Australia) Pty Ltd XD Smartra - 125kHz Immobiliser Old Variant - Tx Idle Antenna Perpendicular Radiated Emissions (dBuV/m) m040411rm040411r # = Ambient Limits: Legend: Source: _ FCC15209 FCC PART 15.209 3mtr LMTS __ Ambients __ Emissions 1 25 26 4 24 13 3 27 Ver 5.5 Build 93radiated emissions site 2 lerderderg t:6502_E c1:C1700804 c2:NONE p:NONE a:NONESite ID: OATS2,Lerderderg Gorge Rd, Bacchus Marsh, VIC Test Officer:Kevin Hansen Frequency (MHz) .1 1 10 .009 30.5 10 20 30 40 50 60 70 80 90 100 110 120 130 # # # # # # # # # # # # # # # # # # # # EMC Technologies Pty. Ltd. - Global Product Certification Job No:m040411 Test Date: 8-04-04 GRAPH No. 5 r:\PCF\m040411i_5.PCF Melbourne- 57 Assembly Drv Tullamarine, 3043, Vic, Australia Ph+(613) 9335 3333 Fax+(613) 9338 9260Sydney---- 16,6 Gladstone Rd Castle Hill, 2154, NSW, Australia Ph+(612) 9899 4599 Fax+(612) 9899 4019Robert Bosch (Australia) Pty Ltd XD Smartra - 125kHz Immobiliser New Variant - Tx ON Antenna Parallel Radiated Emissions (dBuV/m) m040411rm040411r # = Ambient Limits: Legend: Source: _ FCC15209 FCC PART 15.209 3mtr LMTS __ Ambients __ Emissions 5 14 7 8 32 33 34 35 Ver 5.5 Build 93radiated emissions site 2 lerderderg t:6502_E c1:C1700804 c2:NONE p:NONE a:NONESite ID: OATS2,Lerderderg Gorge Rd, Bacchus Marsh, VIC Test Officer:Kevin Hansen Peaks:No Freq Peak Qp Val FCC15209 dL1 (MHz) (dBuV/m) (dBuV/m) (dB) 1 0.125 75.4 75.4 105.5 -30.1 Frequency (MHz) .1 1 10 .009 30.5 10 20 30 40 50 60 70 80 90 100 110 120 130 v ^ 1 ~ # # # # # # # # # # # # # # # # # # # EMC Technologies Pty. Ltd. - Global Product Certification Job No:m040411 Test Date: 8-04-04 GRAPH No. 6 r:\PCF\m040411i_6.PCF Melbourne- 57 Assembly Drv Tullamarine, 3043, Vic, Australia Ph+(613) 9335 3333 Fax+(613) 9338 9260Sydney---- 16,6 Gladstone Rd Castle Hill, 2154, NSW, Australia Ph+(612) 9899 4599 Fax+(612) 9899 4019Robert Bosch (Australia) Pty Ltd XD Smartra - 125kHz Immobiliser New Variant - Tx ON Antenna Perpendicular Radiated Emissions (dBuV/m) m040411rm040411r # = Ambient Limits: Legend: Source: _ FCC15209 FCC PART 15.209 3mtr LMTS __ Ambients __ Emissions 1 13 3 4 36 37 34 39 Ver 5.5 Build 93radiated emissions site 2 lerderderg t:6502_E c1:C1700804 c2:NONE p:NONE a:NONESite ID: OATS2,Lerderderg Gorge Rd, Bacchus Marsh, VIC Test Officer:Kevin Hansen Peaks:No Freq Peak Qp Val FCC15209 dL1 (MHz) (dBuV/m)…

Text truncated - open the document above for the full version.

FCC ID: LXP-VIM223 (IC: 2298A-VIM223) Report No. M040411_Cert_Immobiliser EMC Technologies Pty Ltd – 57 Assembly Drive, Tullamarine VIC 3043 Australia www.emctech.com.au EMC Technologies Report Number: M040411_Cert_Immobiliser APPENDIX B2 – Test Setup Photographs FCC ID: LXP-VIM223 (IC: 2298A-VIM223) Report No. M040411_Cert_Immobiliser EMC Technologies Pty Ltd – 57 Assembly Drive, Tullamarine VIC 3043 Australia www.emctech.com.au APPENDIX B2 – Test Setup Photographs