LZX36248-X2.4 GHz Cordless Phone with Digital Answering Machine

EXCURSION 36248 MANUAL MAY 25 , 2000 FCC INFORMATION .......................................PAGE 1 HANDSET CONTROL-CORDLESS PHONE.............PAGE 3 HANDSET CONTROL-ANSWERING SYSTEM........PAGE4 BASE UNIT CONTROL ...................................PAGE 5 INITIAL SETUP ...........................................PAGE6 TELEPHONE OPERATION SPEED DIALING ......................................PAGE7 USING CALLER ID AND CALL WAITING ID ...............PAGE 9 PROGRAMING MODE .................................... PAGE 13 ANSWERING MACHINE OPERATION ................PAGE 16 REMOTE OPERATION .....................................PAGE 19 REMARK & DISPLAY ON BASE ........................PAGE 21 READING DISPLAY MESSAGE ......................... PAGE 22 FCC INFORMATION FCC Regulations This equipment has been tested and complies with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are intended to provide reasonable protection against such interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures : . Reorient or relocate the receiving antenna. . Increase the separation between the equipment and receiver. . Connect the equipment into an outlet on an electrical circuit different from that to which the receiver is connected. . Consult the dealer or an experienced radio/TV technician. Upon request from your telephone company, you must provide the FCC registration number and the Ringer Equivalence Number(REN) found on the bottom of your 36248. An FCC compliant telephone cord and modular plug are provided with this equipment. This equipment is designed to be connected to the telephone network or premises wiring using a compatible modular jack which is Part 68 compliant. Telephone Company Procedures The goal of the telephone company is to provide you with the best service it can. In order to do this, it may occasionally have to make changes in its equipment, operations, or procedures. If these changes might affect your service or the operation of your equipment, the telephone company will give you notice in writing to allow you to make any changes necessary to maintain uninterrupted service. If you have any questions about your telephone line, such as how many pieces of equipment you can connect to it, the telephone company will provide this information upon request. In certain circumstances, it may be necessary for the telephone company to request information from you about the equipment which you have connected to your telephone line. Upon request of the telephone company, you must provide the FCC registration number and the Ringer Equivalence Number(REN) of the equipment which is connected to your line. Both of these numbers are listed on the equipment label on the bottom of your 36248. In most(but not all) areas, the sum of the RENs of all devices connected to one line should not exceed 5. To be certain of the number of devices you may connect to your line as determined by the REN, you should contact your local telephone company. Note: This equipment is hearing aid-compatible(HAC). 1 Type of Service Your cordless telephone is designed for use on standard device telephone lines. The phone connects to the telephone line with a standard jack called the USOC-RJ11C. Connection to telephone company-provided coin service (central office implemented systems) is prohibited. Connection to party line service is subject to State tariffs. If Problems Arise If any of your telephone equipment is not operating properly, you should immediately remove it from your telephone line, as it may cause harm to the telephone network. If the telephone company notes a problem, they may temporarily stop service. When practical, they will notify you before this disconnection. If advance notice is not feasible, you will be notified as soon as possible. When you are notified, you will be given the opportunity to correct the problem and will be informed of your right to file a complaint with the FCC. In the event repairs are ever needed on your cordless telephone, they should be done by an authorized representative of For information, contact Industry Canada(IC)regulations This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numerique de la classe B respecte toutes les exigences du Reglement sur le material brouilleur du Canada. Notice: The Canadian Department of Communications label identifies certified equipment. This certification means the equipment meets certain telecommunications network Protective, operational and safety requirements. The Department does not guarantee the equipment will operate to the customer’s satisfaction. Before installing this equipment users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. Sometimes, the company’s inside wiring associated with a single line individual service may be extended with a certified connector assembly (telephone extension cord). The customer should be aware that compliance with these conditions may not prevent degradation of service in some situations. Repairs to certified equipment should be made by an authorized Canadian maintenance Facility by the supplier. Any equipment malfunctions or repairs or alterations made by The user to the equipment may give the telecommunications company cause to request the user to disconnect th…

Text truncated - open the document above for the full version.

Note: This report may not be duplicated without prior written consent of Bay Area Compliance Laboratory Corporation. This report must not be used by the client to claim product endorsement by NVLAP or any agency of the U.S. Government. FCC PART 15 Subpart C EUT External Photo FOR UNICAL ENTERPRISES, INC. 16960 Gale Avenue City of Industry, CA 91745 FCC ID: LZX36248-X June 29, 2000 This Report Concerns: Original Report Equipment Type: 2.4 GHz Cordless Phone with Digital Answering Machine and Caller ID– Household Appliances Test Engineer: Edward Yan Test Date: June 27, 2000 Reviewed By: John Y. Chan – Engineering Manager Prepared By: Bay Area Compliance Laboratory Corporation 230 Commercial Street, Suite 2 Sunnyvale, CA 94086 (408) 732-9162 Unical Enterprises, Inc. FCC ID: LZX36248-X Report # EUT external photo.doc FCC Part 15 Subpart C Test Report Page 2 of 10 TABLE OF CONTENTS 1 - GENERAL INFORMATION.................................................................................................................................3 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT)..............................................................................3 1.2 PURPOSE...............................................................................................................................................................3 1.3 RELATED SUBMITTAL(S)/GRANT(S).....................................................................................................................3 1.4 TEST METHODOLOGY............................................................................................................................................3 1.5 TEST FACILITY......................................................................................................................................................3 1.6 TEST EQUIPMENT LIST..........................................................................................................................................4 1.7 EQUIPMENT UNDER TEST (EUT)...........................................................................................................................4 2 – EUT PHOTOGRAPHS..........................................................................................................................................5 2.1 EUT OVERALL - FRONT VIEW..............................................................................................................................5 2.2 EUT OVERALL - REAR VIEW................................................................................................................................6 2.3 EUT HANDSET - FRONT VIEW..............................................................................................................................7 2.4 EUT HANDSET - REAR VIEW................................................................................................................................8 APPENDIX A – AGENT AUTHORIZATION LETTER.........................................................................................9 Unical Enterprises, Inc. FCC ID: LZX36248-X Report # EUT external photo.doc FCC Part 15 Subpart C Test Report Page 3 of 10 1 - GENERAL INFORMATION 1.1 Product Description for Equipment Under Test (EUT) The UNICAL ENTERPRISES, INC.’s 36248-X or the "EUT" as referred to in this report is a 2.4 GHz Cordless Phone with Digital Answering Machine and Caller ID. The EUT was composed of two parts, one is a Handset which measured 7.0” L x 1.5” W x 2.5”H, and the other is a Base which measures 7.5”L x 6.0”W x 2.0”H. 1.2 Purpose This document is a qualification test report based on the Electromagnetic Interference (EMI) tests performed on the 2.4 GHz Cordless Phone with Digital Answering Machine and Caller ID, Model is 36248-X. The EMI measurements were performed according to the measurement procedure described in ANSI C63.6: 1992. The tests were performed in order to determine whether the electromagnetic emissions from the equipment under test, referred to as EUT hereafter, are within the specification limits defined by FCC Title 47, Part 15, Subpart C, section 15.205, 15.207, and 15.249. 1.3 Related Submittal(s)/Grant(s) No Related Submittals 1.4 Test Methodology All measurements contained in this report were conducted with ANSI C63.4 –1992, American National Standard for Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the range of 9 kHz to 40 GHz. All radiated and conducted emissions measurement was performed at Bay Area Compliance Laboratory, Corp. The radiated testing was performed at an antenna-to-EUT distance of 3 meters. 1.5 Test Facility The Open Area Test site used by Bay Area Compliance Laboratory Corporation to collect radiated and conducted emission measurement data is located in the back parking lot of the building at 230 Commercial Street, Suite 2, Sunnyvale, California, USA. Test sites at Bay Area Compliance Laboratory Corporation has been fully described in reports submitted to the Federal Communication Commission (FCC) and Voluntary Control Council for Interference (VCCI). The details of these reports has been found to be in compliance with the requirements of Section 2.948 of the FCC Rules on February 11 and December 10, 1997 and Article 8 of the VCCI regulations on December 25, 1997. The facility also complies with the radiated and AC line conducted test site criteria set forth in ANSI C63.4-1992. The Federal Communications Commission and Voluntary Control Council for Interference has the reports on file and is listed under FCC file 31040/SIT 1300F2 and VCCI Registration No.: C-674 and R-657. The test sites has been approved by the FCC and VCCI for public use and is listed in the FCC Public Access Link (PAL) database. Additionally, Bay Area Compliance Laboratory Corporation is a National Institute of Standards and Technology (NIST) accredited laboratory, under the National Voluntary Laboratory Accredited Program (NVLA…

Text truncated - open the document above for the full version.

Note: This report may not be duplicated without prior written consent of Bay Area Compliance Laboratory Corporation. This report must not be used by the client to claim product endorsement by NVLAP or any agency of the U.S. Government. FCC PART 15 Subpart C EUT FCC ID Label location FOR UNICAL ENTERPRISES, INC. 16960 Gale Avenue City of Industry, CA 91745 FCC ID: LZX36248-X June 29, 2000 This Report Concerns: Original Report Equipment Type: 2.4 GHz Cordless Phone with Digital Answering Machine and Caller ID– Household Appliances Test Engineer: Edward Yan Test Date: June 27, 2000 Reviewed By: John Y. Chan – Engineering Manager Prepared By: Bay Area Compliance Laboratory Corporation 230 Commercial Street, Suite 2 Sunnyvale, CA 94086 (408) 732-9162 Unical Enterprises, Inc. FCC ID: LZX36248-X Report # EUT ID Label.doc FCC Part 15 Subpart C Test Report Page 2 of 7 TABLE OF CONTENTS 1 - GENERAL INFORMATION.................................................................................................................................3 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT)..............................................................................3 1.2 PURPOSE...............................................................................................................................................................3 1.3 RELATED SUBMITTAL(S)/GRANT(S).....................................................................................................................3 1.4 TEST METHODOLOGY............................................................................................................................................3 1.5 TEST FACILITY......................................................................................................................................................3 1.6 TEST EQUIPMENT LIST..........................................................................................................................................4 1.7 EQUIPMENT UNDER TEST (EUT)...........................................................................................................................4 2 – FCC PRODUCT LABELING AND WARNING STATEMENT.......................................................................5 2.1 FCC ID LABEL.....................................................................................................................................................5 2.2 PROPOSED LABEL LOCATION ON EUT..................................................................................................................5 2.3 FCC WARNING STATEMENT.................................................................................................................................5 APPENDIX A – AGENT AUTHORIZATION LETTER.........................................................................................6 Unical Enterprises, Inc. FCC ID: LZX36248-X Report # EUT ID Label.doc FCC Part 15 Subpart C Test Report Page 3 of 7 1 - GENERAL INFORMATION 1.1 Product Description for Equipment Under Test (EUT) The UNICAL ENTERPRISES, INC.’s 36248-X or the "EUT" as referred to in this report is a 2.4 GHz Cordless Phone with Digital Answering Machine and Caller ID. The EUT was composed of two parts, one is a Handset which measured 7.0” L x 1.5” W x 2.5”H, and the other is a Base which 1.2 Purpose This document is a qualification test report based on the Electromagnetic Interference (EMI) tests performed on the 2.4 GHz Cordless Phone with Digital Answering Machine and Caller ID, Model is 36248-X. The EMI measurements were performed according to the measurement procedure described in ANSI C63.6: 1992. The tests were performed in order to determine whether the electromagnetic emissions from the equipment under test, referred to as EUT hereafter, are within the specification limits defined by FCC Title 47, Part 15, Subpart C, section 15.205, 15.207, and 15.249. 1.3 Related Submittal(s)/Grant(s) No Related Submittals 1.4 Test Methodology All measurements contained in this report were conducted with ANSI C63.4 –1992, American National Standard for Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the range of 9 kHz to 40 GHz. All radiated and conducted emissions measurement was performed at Bay Area Compliance Laboratory, Corp. The radiated testing was performed at an antenna-to-EUT distance of 3 meters. 1.5 Test Facility The Open Area Test site used by Bay Area Compliance Laboratory Corporation to collect radiated and conducted emission measurement data is located in the back parking lot of the building at 230 Commercial Street, Suite 2, Sunnyvale, California, USA. Test sites at Bay Area Compliance Laboratory Corporation has been fully described in reports submitted to the Federal Communication Commission (FCC) and Voluntary Control Council for Interference (VCCI). The details of these reports has been found to be in compliance with the requirements of Section 2.948 of the FCC Rules on February 11 and December 10, 1997 and Article 8 of the VCCI regulations on December 25, 1997. The facility also complies with the radiated and AC line conducted test site criteria set forth in ANSI C63.4-1992. The Federal Communications Commission and Voluntary Control Council for Interference has the reports on file and is listed under FCC file 31040/SIT 1300F2 and VCCI Registration No.: C-674 and R-657. The test sites has been approved by the FCC and VCCI for public use and is listed in the FCC Public Access Link (PAL) database. Additionally, Bay Area Compliance Laboratory Corporation is a National Institute of Standards and Technology (NIST) accredited laboratory, under the National Voluntary Laboratory Accredited Program (NVLAP). The scope of the accreditation covers the FCC Method - 47 CFR Part 15 - Digital Devices, Unical Enterprises, Inc. FCC ID: LZX36248-X Report # EUT ID Label.doc FCC Part 15 Subpart C Test Report Page 4 of 7 IEC/CISPR 22: 1993, and…

Text truncated - open the document above for the full version.

Note: This report may not be duplicated without prior written consent of Bay Area Compliance Laboratory Corporation. This report must not be used by the client to claim product endorsement by NVLAP or any agency of the U.S. Government. FCC PART 15 Subpart C EUT Internal Photo FOR UNICAL ENTERPRISES, INC. 16960 Gale Avenue City of Industry, CA 91745 FCC ID: LZX36248-X June 29, 2000 This Report Concerns: Original Report Equipment Type: 2.4 GHz Cordless Phone with Digital Answering Machine and Caller ID– Household Appliances Test Engineer: John Chan / Edward Yan Test Date: June 27, 2000 Reviewed By: John Y. Chan – Engineering Manager Prepared By: Bay Area Compliance Laboratory Corporation 230 Commercial Street, Suite 2 Sunnyvale, CA 94086 (408) 732-9162 Unical Enterprises, Inc. FCC ID: LZX36248-X Report # EUT internal photo.doc FCC Part 15 Subpart C Test Report Page 2 of 16 TABLE OF CONTENTS 1 - GENERAL INFORMATION.................................................................................................................................3 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT)..............................................................................3 1.2 PURPOSE...............................................................................................................................................................3 1.3 RELATED SUBMITTAL(S)/GRANT(S)......................................................................................................................3 1.4 TEST METHODOLOGY............................................................................................................................................3 1.5 TEST FACILITY......................................................................................................................................................3 1.6 TEST EQUIPMENT LIST..........................................................................................................................................4 1.7 EQUIPMENT UNDER TEST (EUT)...........................................................................................................................4 2 – EUT PHOTOGRAPHS..........................................................................................................................................5 2.1 EUT HANDSET – ENCLOSURE OFF WITH SHIELDING VIEW..................................................................................5 2.2 EUT HANDSET – ENCLOSURE OFF WITHOUT SHIELDING VIEW............................................................................6 2.3 EUT HANDSET MAIN BOARD COMPONENT VIEW.................................................................................................7 2.4 EUT HANDSET MAINBOARD CIRCUIT VIEW.........................................................................................................8 2.5 EUT RF BOARD COMPONENT VIEW.....................................................................................................................9 2.6 EUT RF BOARD CIRCUIT VIEW..........................................................................................................................10 2.7 EUT BASE UNIT ENCLOSURE OFF VIEW.............................................................................................................11 2.8 EUT BASE UNIT MAINBOARD CIRCUIT VIEW.....................................................................................................12 2.9 EUT BASE UNIT VOICE MAIL BOARD COMPONENT VIEW..................................................................................13 2.10 EUT BASE UNIT VOICE MAIL BOARD CIRCUIT VIEW.......................................................................................14 APPENDIX A – AGENT AUTHORIZATION LETTER.......................................................................................15 Unical Enterprises, Inc. FCC ID: LZX36248-X Report # EUT internal photo.doc FCC Part 15 Subpart C Test Report Page 3 of 16 1 - GENERAL INFORMATION 1.1 Product Description for Equipment Under Test (EUT) The UNICAL ENTERPRISES, INC.’s 36248-X or the "EUT" as referred to in this report is a 2.4 GHz Cordless Phone with Digital Answering Machine and Caller ID. The EUT was composed of two parts, one is a Handset which measured 7.0” L x 1.5” W x 2.5”H, and the other is a Base which measures 7.5”L x 6.0”W x 2.0”H. 1.2 Purpose This document is a qualification test report based on the Electromagnetic Interference (EMI) tests performed on the 2.4 GHz Cordless Phone with Digital Answering Machine and Caller ID, Model is 36248-X. The EMI measurements were performed according to the measurement procedure described in ANSI C63.6: 1992. The tests were performed in order to determine whether the electromagnetic emissions from the equipment under test, referred to as EUT hereafter, are within the specification limits defined by FCC Title 47, Part 15, Subpart C, section 15.205, 15.207, and 15.249. 1.3 Related Submittal(s)/Grant(s) No Related Submittals 1.4 Test Methodology All measurements contained in this report were conducted with ANSI C63.4 –1992, American National Standard for Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the range of 9 kHz to 40 GHz. All radiated and conducted emissions measurement was performed at Bay Area Compliance Laboratory, Corp. The radiated testing was performed at an antenna-to-EUT distance of 3 meters. 1.5 Test Facility The Open Area Test site used by Bay Area Compliance Laboratory Corporation to collect radiated and conducted emission measurement data is located in the back parking lot of the building at 230 Commercial Street, Suite 2, Sunnyvale, California, USA. Test sites at Bay Area Compliance Laboratory Corporation has been fully described in reports submitted to the Federal Communication Commission (FCC) and Voluntary Control Council for Interference (VCCI). The details of these reports has been found to be in comp…

Text truncated - open the document above for the full version.

Note: This report may not be duplicated without prior written consent of Bay Area Compliance Laboratory Corporation. This report must not be used by the client to claim product endorsement by NVLAP or any agency of the U.S. Government. FCC PART 15 Subpart C EMI MEASUREMENT AND TEST REPORT FOR UNICAL ENTERPRISES, INC. 16960 Gale Avenue City of Industry, CA 91745 FCC ID: LZX36248-X June 29, 2000 This Report Concerns: Original Report Equipment Type: 2.4 GHz Cordless Phone with Digital Answering Machine and Caller ID– Household Appliances Test Engineer: Edward Yan Test Date: June 27, 2000 Reviewed By: John Y. Chan – Engineering Manager Prepared By: Bay Area Compliance Laboratory Corporation 230 Commercial Street, Suite 2 Sunnyvale, CA 94086 (408) 732-9162 Unical Enterprises, Inc. FCC ID: LZX36248-X Report # test report.doc FCC Part 15 Subpart C Test Report Page 2 of 25 TABLE OF CONTENTS 1 - GENERAL INFORMATION.................................................................................................................................3 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT)..............................................................................3 1.2 PURPOSE...............................................................................................................................................................3 1.3 RELATED SUBMITTAL(S)/GRANT(S).....................................................................................................................3 1.4 TEST METHODOLOGY............................................................................................................................................3 1.5 TEST FACILITY......................................................................................................................................................3 1.6 TEST EQUIPMENT LIST..........................................................................................................................................4 1.7 EQUIPMENT UNDER TEST (EUT)...........................................................................................................................4 1.8 LOCAL SUPPORT EQUIPMENT................................................................................................................................4 FOR BASE ONLY..........................................................................................................................................................4 FOR HANDSET ONLY...................................................................................................................................................5 1.9 REMOTE SUPPORT EQUIPMENT.............................................................................................................................5 1.10 EXTERNAL I/O CABLING FOR THE EUT BASE UNIT............................................................................................5 1.11 EXTERNAL I/O CABLING FOR THE EUT HANDSET UNIT.....................................................................................5 2 - SYSTEM TEST CONFIGURATION....................................................................................................................6 2.1 DESCRIPTION OF TEST CONFIGURATION...............................................................................................................6 2.2 CONFIGURATION OF TEST SYSTEM (BASE UNIT)..................................................................................................7 2.3 CONFIGURATION OF TEST SYSTEM (HANDSET UNIT)...........................................................................................8 2.4 TEST SETUP BLOCK DIAGRAM (BASE UNIT).........................................................................................................9 2.5TEST SETUP BLOCK DIAGRAM (HANDSET UNIT).................................................................................................10 2.6 EQUIPMENT MODIFICATIONS..............................................................................................................................11 3 - CONDUCTED EMISSIONS TEST DATA.........................................................................................................12 3.1 MEASUREMENT UNCERTAINTY...........................................................................................................................12 3.2 EUT SETUP.........................................................................................................................................................12 3.3 SPECTRUM ANALYZER SETUP.............................................................................................................................12 3.4 TEST PROCEDURE................................................................................................................................................13 3.5 SUMMARY OF TEST RESULTS..............................................................................................................................13 3.6 CONDUCTED EMISSIONS TEST DATA...................................................................................................................13 3.7 PLOT OF CONDUCTED EMISSIONS TEST DATA.....................................................................................................13 4 - RADIATED EMISSION DATA...........................................................................................................................14 4.1 MEASUREMENT UNCERTAINTY...........................................................................................................................14 4.2 EUT SETUP.........................................................................................................................................................14 4.3 SPECTRUM ANALYZER SETUP.............................................................................................................................14 4.4 TEST PROCEDURE...........…

Text truncated - open the document above for the full version.