M4ZIN610Infinity 610

INfinity 610 USER’s GUIDE V1.0 August 25, 2011 © 2011 Sirit Inc., All Rights Reserved. “Sirit”, the Sirit Design, “RFID by Sirit”, the RFID by Sirit Design and “vision beyond sight” are all trademarks of Sirit Inc. All other trademarks are the property of their respective owners. Specifications are subject to change without notice. This product is covered by one or more of the following patents: U.S. Patent No. 7,199,713, 7,209,040, 6,346,881, and 6,617,962. Disclaimer and Limitation of Liability The content of this manual is for information use only and is subject to change without notice. Sirit assumes no responsibility or liability for any errors or inaccuracies that may appear in this publication. No part of this manual may be reproduced in any form or by any means, electronic, mechanical, recording, or otherwise, without the prior written permission of Sirit. Sirit products are not designed, intended, authorized or warranted to be suitable for life support applications or any other life critical applications which could involve potential risk of death, personal injury, property damage, or environmental damage. FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult FSTech-Sirit or an experienced radio/TV technician for help. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. About Sirit, a Federal Signal Technologies Company Sirit, a Federal Signals Technologies Company, designs, develops, manufactures and sells Radio Frequency Identification (RFID) technology. Targeted at a diverse set of markets RFID technology has become a core technology for applications including: electronic toll collection, access control, cashless payment systems, product identification, and supply chain management systems including logistics, warehousing and manufacturing, and asset management. Federal Signal Technologies 2 Technology Irvine, CA 92618 Tel: (949) 341-0409 Fax (949) 341-0521 Web: www.fstech.com Sirit 1321 Valwood Parkway, Suite 620 Carrollton, Texas 75006 United States Tel: 972.243.7208 Fax: 972.243.8034 Toll Free: 1.866.338.9586 Web: www.sirit.com Preface INfinity 610 User’s Guide i Preface Intended audience This document is intended for those who wish to setup and operate the INfinity 610 Radio Frequency Identification system. Before attempting to install, configure, and operate this product, you should be familiar with the following: h Windows-based software installation and operation h Device communication parameters including Ethernet and serial communications h RFID reader configuration including antenna placement h Basic digital input/output control What’s in this guide The information in this guide is presented as follows: Chapter 1 - Reader Overview:This chapter provides a brief overview of the INfinity 610 hardware and software. Chapter 2 - Reader Equipment Installation – This chapter describes how to mechanically and electrically install the reader. Chapter 3 - Reader Startup Tool (RST) Software Installation – This chapter describes how to install the Microsoft Windows RST application. Chapter 4 - Reader Operation – This chapter describes how to initially test a reader and how to operate deployed readers. Chapter 5 - Reader Startup Tool (RST) – This chapter describes the RST and the various functions you can perform with this Microsoft Windows application. Chapter 6 - Reader Configuration Tool (RCT) – This chapter describes the RCT and the various functions you can perform with this embedded reader application. Chapter 7 - Configuring Digital Inputs and Outputs – This chapter describes how to setup the reader’s digital inputs and outputs. Chapter 8 - Specifications – This chapter detailed mechanical, electrical, and environmental specifications for the INfinity 610. Chapter 9 - Safety Instructions – This chapter provides important safety information about the INfinity 610. All users must read this section before installing or operating this reader. Appendix A - IN610 Digital Input/Output Interface Module – This appendix provides information for installing, configuring, and using the external digital interface module. Appendix B - USB Port Setup – This appendix includes USB port driver installation and setup procedures for both Windows XP and Windows 7. Appendix C - Disposal of the INfinity 610 Reader – This appendix provides instruction for removing the battery and disposing of the reader. ii INfinity 610 User’s Guide What’s New in this Version Version 1.0 of this User’s Guide is the initial version. Conventions used in this manual The following conventions are used in this manual: Bold courier font indicates code entered by the user (values) within parentheses indicate parameters (values) in italics ind…

Text truncated - open the document above for the full version.

Sirit Technologies Inc. Tel: 972.243.7208 1321 Valwood Parkway, Suite 620 Toll Free: 877.492.0101 Carrollton, Texas Fax: 972.243.8034 75006 USA Web site: www.sirit.com Letter of Agency Date: August 26, 2011 American Telecommunications Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 To Whom It May Concern: Please be advised that Sirit Technologies Inc. authorizes Washington Laboratories, Ltd. to act on our behalf, until otherwise notified, for applications submitted to American Telecommunications Certification Body, Inc. (ATCB). The following personnel of Washington Laboratories, Ltd. are authorized for M4ZIN610 certification: • Michael F. Violette, President • Steven D. Koster, EMC Operations Manager We certify that we are not subject to denial of federal benefits that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse ACT of 1988, U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002(b), to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you for your attention to this matter. Randal Roebuck, Director of DSRC Interoperability, Regulations and Connected Vehicle.

Sirit Technologies Inc. Tel: 972.243.7208 1321 Valwood Parkway, Suite 620 Toll Free: 877.492.0101 Carrollton, Texas Fax: 972.243.8034 75006 USA Web site: www.sirit.com Request for Confidentiality Date: August 26, 2011 Federal Communications Commission Office of Engineering and Technology Equipment Authorization Division 7345 Oakland Mills Road Columbia, MD 21046 RE: Equipment Type Certification Application FCC ID: M4ZIN610 Please be advised that under the provision of 47 CFR 0.459 the following exhibits are to be held confidential on behalf of Sirit Technologies Inc. • IN610 Schematics • IN610 Operational Description • IN610 Block Diagrams The application contains technical information that Sirit Technologies Inc. deems to be trade secrets and proprietary. If made public, the information might be used to the disadvantage of the applicant in the market place. Thank you for your attention to this matter. Signatory Randal Roebuck Director of DSRC Interoperability, Regulations and Connected Vehicle

Assembled Chassis Assembled Chassis, Connector View 1 Assembled Chassis, Connector View 2 Bottom View & Regulatory Label Location Side View 1 Side View 2 Back View

Bottom View & Regulatory Label Location

Printed Circuit Board, Top Printed Circuit Board, Bottom Printed Circuit Board, Connector Side Chassis Bottom Printed Circuit Board Installed in Chassis Top

Certificates and reports shall not be reproduced except in full, without the written permission of Washington Labs, Limited. Maximum Permissible Exposure Evaluation For the Sirit Technologies Inc. INfinity 610 FCC ID: M4ZIN610 IC: 3637B-IN610 Septemeber 28, 2011 WLL Report: 12149-MPE Prepared for: SIRIT TECHNOLOGIES INC. 1321 VALWOOD PARKWAY STE 620 C ARROLLTON, TX 75006 Prepared by: WASHINGTON LABORATORIES, LTD. 7560 LINDBERGH DRIVE G AITHERSBURG, MARYLAND 20879 Testing Certificate AT-1448 Sirit Technologies Infinity 610 RF Exposure Test Report September, 2011 WLL Report #12047-MPE - ii - © 2011 Washington Laboratories, Ltd. Maximum Permissible Exposure Evaluation For the Sirit Technologies Inc. - UK INfinity 610 September 28, 2011 WLL Report # 12149-MPE Prepared by: John P. Repella EMC Engineer Reviewed by: Steven D. Koster VP, EMC & Wireless Sirit Technologies Infinity 610 RF Exposure Test Report September, 2011 WLL Report #12047-MPE - iii - © 2011 Washington Laboratories, Ltd. Abstract This report has been prepared on behalf of Sirit Technologies Inc. to document the findings of the maximum permissible exposure evaluation on the Sirit Technologies Inc. INfinity 610 RFID Fixed Reader. The purpose of this evaluation is to establish a minimum safe distance as per the RF exposure requirements as defined in FCC §1.1307 & §1.1310. This report documents the results of testing to the requirements of:  CFR Title 47 Volume 1 Practice and Procedure; (1.1307) Environmental Assessments The Evaluation was performed by Washington Laboratories, Ltd, 7560 Lindbergh Drive, Gaithersburg, MD 20879. Washington Laboratories, Ltd. has been accepted as an EMC Conformity Assessment Body (CAB) under the United States/European Union Memorandum of Agreement. Washington Laboratories, Ltd. is accredited by ACLASS under Testing Certificate AT-1448. Revision History Reason Date Rev 0 Initial Release September 28, 2011 Sirit Technologies Infinity 610 RF Exposure Test Report September, 2011 WLL Report #12047-MPE - iv - © 2011 Washington Laboratories, Ltd. Table of Contents Abstract .................................................................................................................................................................... ii 1 Introduction ................................................................................................................................................ 1 2 Requirements .............................................................................................................................................. 1 2.1 Transmitter Categories ............................................................................................................................. 1 2.2 Exposure Categories ................................................................................................................................ 1 3 Device Summary ......................................................................................................................................... 3 4 Radio Frequency Radiation Exposure Evaluation .................................................................................. 3 List of Tables Table 1: MPE Limits ..................................................................................................................................................2 Table 2: Device Summary of the INfinity 610 RFID Fixed Reader ...........................................................................3 Table 3: Transmitter MPE Calculation Summary ......................................................................................................4 Sirit Technologies Infinity 610 RF Exposure Test Report September, 2011 WLL Report #12047-MPE - Page 1 of 4 - © 2011 Washington Laboratories, Ltd. 1 Introduction This report has been prepared on behalf of Sirit Technologies Inc. to show compliance with the RF exposure requirements as defined in FCC §1.1307. Testing supporting this evaluation was performed at Washington Laboratories, Ltd, 7560 Lindbergh Drive, Gaithersburg, MD 20879. Washington Laboratories, Ltd. has been accepted as an EMC Conformity Assessment Body (CAB) under the United States/European Union Memorandum of Agreement. Washington Laboratories, Ltd. is accredited with ACLASS under Testing Certificate AT-1448. 2 Requirements Three different categories of transmitters are defined by the FCC in OET Bulletin 65. These categories are fixed installation, mobile, and portable. Additionally, the FCC categorizes the use of the devices based on the user’s awareness and the ability to exercise control over his or her exposure. The two categories are defined as Occupational/Controlled Exposure and General Population/Uncontrolled Exposure. 2.1 Transmitter Categories 2.1.1 Fixed Installations A fixed location means that the device, including its antenna, is physically secured at a permanent location and is not able to be easily moved to another location. Additionally, distance to humans from the antenna is maintained to at least 2 meters. 2.1.2 Mobile Devices A mobile device is defined as a transmitting device designed to be used in other than fixed locations and to be generally used in such a way that a separation distance of at least 20 centimeters is normally maintained between the transmitter's radiating structures and the body of the user or nearby persons. Transmitters designed to be used by consumers or workers that can be easily re-located, such as a wireless modem operating in a laptop computer, are considered mobile devices if they meet the 20 centimeter separation requirement. The FCC rules for evaluating mobile devices for RF compliance are found in 47 CFR §2.1091. 2.1.3 Portable Devices A portable device is defined as a transmitting device designed to be used so that the radiating structure(s) of the device is/are within 20 centimeters of the body of the user. Portable device requirements are found in Section 2.1093 of the FCC's Rules (47 CFR§2…

Text truncated - open the document above for the full version.

Certificates and reports shall not be reproduced except in full, without the written permission of Washington Laboratories, Limited. FCC & Industry Canada Certification Test Report For the Sirit Technologies Inc. INfinity 610 FCC ID: M4ZIN610 IC: 3637B-IN610 WLL JOB# 12149-01 Rev 1 September 14, 2011 Re-issued September 28, 2011 Prepared for: Sirit Technologies Inc. 1321 Valwood Parkway Ste 620 Carrollton, TX 75006 Prepared By: Washington Laboratories, Ltd. 7560 Lindbergh Drive Gaithersburg, Maryland 20879 Testing Certificate AT-1448 SIRIT Technologies Inc. INfinity 610 FCC Certification Test Report September, 2011 WLL Report #12149-01 Rev 1 - ii - © 2011 Washington Laboratories, Ltd. FCC & Industry Canada Certification Test Report For the Sirit Technologies Inc. INfinity 610 FCC ID: M4ZIN610 IC: 3637B-IN610 WLL JOB# 12149-01 Rev 0 September 14, 2011 Re-issued September 28, 2011 Prepared by: John P. Repella Compliance Engineer Reviewed by: Steven D. Koster VP, EMC & Wireless SIRIT Technologies Inc. INfinity 610 FCC Certification Test Report September, 2011 WLL Report #12149-01 Rev 1 - iii - © 2011 Washington Laboratories, Ltd. Abstract This report has been prepared on behalf of Sirit Technologies Inc. Inc. to support the attached Application for Equipment Authorization. The test report and application are submitted for a Frequency Hopping Spread Spectrum Transmitter under Part 15.247 (10/2009) of the FCC Rules and Regulations and Spectrum Management and Telecommunications Policy RSS-210 of Industry Canada. This Certification Test Report documents the test configuration and test results for the Sirit Technologies Inc. Inc. INfinity 610. Testing was performed on an Open Area Test Site (OATS) of Washington Laboratories, Ltd, 7560 Lindbergh Drive, Gaithersburg, MD 20879. Site description and site attenuation data have been placed on file with the FCC's Sampling and Measurements Branch at the FCC laboratory in Columbia, MD. The Industry Canada OATS numbers are 3035A-1 and 3035A-2 for Washington Laboratories, Ltd. Site 1 and Site 2, respectively. Washington Laboratories, Ltd. has been accepted by the FCC and approved by ACLASS under Certificate AT-1448 as an independent FCC test laboratory. The Sirit Technologies Inc. Inc. INfinity 610 complies with the limits for a Frequency Hopping Spread Spectrum Transmitter device under FCC Part 15.247 and Industry Canada RSS-210. Revision History Description of Change Date Rev 0 Initial Release September 14, 2011 Rev 1 Edited per client comments September 28, 2011 SIRIT Technologies Inc. INfinity 610 FCC Certification Test Report September, 2011 WLL Report #12149-01 Rev 1 - iv - © 2011 Washington Laboratories, Ltd. Table of Contents Abstract .................................................................................................................................... ii 1 Introduction ......................................................................................................................................1 1.1 Compliance Statement ................................................................................................................ 1 1.2 Test Scope ................................................................................................................................... 1 1.3 Contract Information ................................................................................................................... 1 1.4 Test and Support Personnel ........................................................................................................ 1 1.5 Abbreviations .............................................................................................................................. 2 2 Equipment Under Test .....................................................................................................................3 2.1 EUT Identification & Description .............................................................................................. 3 2.2 Test Configuration ...................................................................................................................... 3 2.3 Testing Algorithm ....................................................................................................................... 3 2.4 Test Location .............................................................................................................................. 4 2.5 Measurements ............................................................................................................................. 4 2.5.1 References ............................................................................................................................... 4 2.6 Measurement Uncertainty ........................................................................................................... 4 3 Test Equipment ................................................................................................................................6 4 Test Summary ..................................................................................................................................7 5 Test Results ......................................................................................................................................8 5.1 Time of Occupancy (15.247 (a)(1)(i) & RSS-210 [A8. 1 (c)]) ................................................... 8 5.2 RF Power Output: (15.247 (b)(2) & RSS-210 [A8.4 (1)]) ....................................................... 10 5.3 Occupied Bandwidth: (15.247 (a) (1)(i) & RSS-210 [A8. 1 (c)]) ............................................ 12 5.4 Channel Spacing and Number of Hop Channels (FCC 15. 247(a)(1) & RSS-210 [A8.1 (b)] .. 18 5.5 Conducted Spurious Emissions at Antenna Terminals (FCC Part §2.1051) ............................ 26 5.6 Radiated Spurious Emissions: (FCC Part 15.205, 15.209 & RSS-210 [A8. 5]) ....................... 43 5.6.1 Test Procedure ................…

Text truncated - open the document above for the full version.

Test Setup Photos ©2008 Washington Laboratories, Ltd Test Setup Photos ©2008 Washington Laboratories, Ltd Test Setup Photos ©2008 Washington Laboratories, Ltd Test Setup Photos ©2008 Washington Laboratories, Ltd Test Setup Photos ©2008 Washington Laboratories, Ltd