MCLADB1761WFIP Set-Top Box with Wi-Fi 11ac

Quick Installation Manual ADB - 1761WF 2 SAFETY INFORMATION AND WARNINGS Before any operation is performed, please read the operation instructions and pre- cautions carefully in order to minimize the possibility of accidents. When you use this Product you shall always respect basic safety measures in order to reduce risk of fire, electric shock or injury, following below instruc- tions. Power Source Use only the Class II power adapter provided with the Product. The Product should be operated only with power source of the same kind as indicated on the power adapter rating plate. The power adapter provided is a limited power source as per UL 60950-1/CAN/CSA- C22.2 No. 60950-1 and it is compliant to national standards of the specific country where the Product is installed. It is strictly forbidden to use different type of power source. The plug socket serves as the main power connection for the Product. Be sure that the power socket being used is easily accessible and located as close to the Product as possible. In order to reduce the risk of fire or electric shock, do not overload the electrical outlet, power strip, or extension power cable. Cleaning Instructions Unplug the Product from the power outlet (or socket) and any other telecommunica- tion interfaces before cleaning. Use a damp cloth for cleaning. Do not use liquid or aerosol cleansers. Maintenance Do not open the case in order to avoid electric shock or exposition to overvoltages. Improper mounting can cause electric shock during further use of the Product. There are no parts inside the Product that can be substituted by the user. Damage requiring service/replacement In case the Product requires service unplug the Product from the electrical outlet and contact your service provider. Typical conditions which may require service: – Liquid has been spilled into the Product. – The Product does not operate normally when you follow the operating instructions. – The Product has been dropped or damaged. – There are noticeable signs of overheating. – The power cord, extension cord, or plug is damaged. – A burning smell or smoke is perceived from the device. Environmental conditions for product installation and use: The Product shall be installed and configured in accordance with the user guide. The Product shall be used and installed indoor with a maximum ambient temperature of 40° C. The Product shall be installed in offices and residential areas only, as they are free from conducting polluting agents (i.e. areas considered pollution degree 2 environments as per standard IEC 1010). The Product shall not be placed near any source of heat or direct sunlight. The Product shall be placed in a well-ventilated area in order to prevent overheating. Do not cover or block the air vents on the Product. These are necessary for proper ventilation. Do not use this Product near water or in close proximity to bath tub, wash bowl, kitchen sink, or laundry basin, in a wet basement, or near a swimming pool. The Product shall not get in contact with water and moisture. Moving the Product from a cold environment to a hot one may cause moisture on some internal parts of the device. Wait until the Product is totally dry before turning it on. In case of fire, do not use water for fire-extinguishing. The Product shall not be used during a lightning storm. There is a remote risk of electric shock from lightning. Connections Ethernet ports must be connected only to devices that support the same kind of in- terface, and the cable used must not leave the building where the Product is installed. This Product is not available to connect to outdoor cable distribution system USB The equipment has to be connected to a standard USB device compliant with limited current circuit (as per UL 60950-1). 3 GETTING STARTED UNPACKING YOUR DIGITAL RECEIVERFRONT PANEL ReceiverPower Supply Installation Guide Quick Installation Guide HD TV Power supply Home Cinema Ethernet router SD TV SD card slot Led indicator in the power on/off button: ƒBlue - operating mode. Blinks while receiving signals from the RCU ƒRed - deep standby mode ƒPurple - normal standby mode. Blinks during software update. Rec LED - Red when recording is in progress (only when the ADB HDD module is connected). WiFi NETWORK CONFIGURATION If you decide to use wireless network please perform the steps listed in the “Connections” section. Make sure the ethernet cable is disconnected. On your TV the “Application Screen” shall appear: 1. select the WiFi network from the list, 2. enter the password if applicable. The front panel LED indicator shall display the following information: CONNECTIONS Installation Notice: Connecting your TV directly to the Audio/Video output of your Set-Top Box will assure a more vivid picture and enhance your viewing enjoyment. Plug in all cables before connecting the decoder to the power supply. Similarly always unplug the decoder from the power supply first, before disconnecting cables from the decoder or reconnecting them. 1. Connect the Ethernet cable or configure WiFi network. 2. Depending on the type of your TV set, connect your receiver either with the HDMI cable (for an HD TV set), jack connector (for an SD TV) or RF cable. 3. You can also connect audio devices such as home cinema. 4. The last step is connecting the decoder to the power supply socket. Now you can switch on your TV set. Make sure that you have selected the appropriate source of signal in the TV. If you are unsure how to do it, please consult your TV user manual. Red bar - no network connection. Blinking red bar - connecting in progress. Two yellow bars - poor signal. Three blue bars - medium strength. Four blue bars - strong signal. RF RCU CONFIGURATION Important: Remote Control Unit is packed separetly. In case when you are provided with an RF RCU please perform simultaneously the following steps in order to pair it with your STB: 1. RF RCU - enter the pairing mode according to the instructions attached to the device. 2…

Text truncated - open the document above for the full version.

HON HAI PRECISION IND. CO., LTD. 5F-1,5 Hsin-An Road Hsinchu, Science-Based Industrial Park Taiwan, R.O.C. A G E N C Y A U T H O R I Z A T I O N L E T T E R Date: 2015/5/8 To whom it may concern: We, the undersigned, hereby authorize Amanda Wu of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan) of Taiwan to act on our behalf in all manners relating to FCC application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Amanda Wu of BV CPS Taoyuan on our behalf shall have the same effect as acts of our own. If you have any questions regarding the authorization, please don’t hesitate to Contact us. Signature: Rio Chen Compliance Manager HON HAI PRECISION IND. CO., LTD. TEL: +886-3-5784975 FAX: +886-3-5775100 E-mail: [email protected]

HON HAI PRECISION IND. CO., LTD. 5F-1,5 Hsin-An Road Hsinchu, Science-Based Industrial Park Taiwan, R.O.C. Date: 2015/5/8 FCC ID: MCLADB1761WF Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, Rio Chen Compliance Manager HON HAI PRECISION IND. CO., LTD. TEL: +886-3-5784975 FAX: +886-3-5775100 E-mail: [email protected]

HON HAI PRECISION IND. CO., LTD. 5F-1,5 Hsin-An Road Hsinchu, Science-Based Industrial Park Taiwan, R.O.C. Date: 2015-05-068 FCC ID: MCLADB1761WF To the attention of Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the commission’s rules, we request short-term confidential treatment for the following information until (year/month/day) or (???days after the Grant Date of Equipment Authorization) in order to ensure sensitive business information remains confidential until the actual marketing of the device: External photos Test Setup photos User’s manual Internal Photos Sincerely yours, ------------------------------------------------------- Rio Chen Compliance Manager HON HAI PRECISION IND. CO., LTD. TEL: +886-3-5784975 FAX: +886-3-5775100 E-mail: [email protected]

Report No.: 150407E02 Page 1 CONSTRUCTION PHOTOS OF EUT Report No.: 150407E02 Page 2 Report No.: 150407E02 Page 3

1.1 500.01828.005 ^d,ŽƵƐŝŶŐ^ĞƌŝĂůŝnjĂƟŽŶ>ĂďĞů 3503.00501.005ĐĂƌƚŽŶůĂďĞů 2503.01094.005 warrantyůĂďĞů 1.5 ^dt/&/^ƉĂƌĞ>ĂďĞů 1.2 1.3 1.4 EAN CodeůĂďĞů ^d,ŽƵƐŝŶŐt/&/>ĂďĞů GŝĨƚďŽdžůĂďĞů 1 1 1 1/10 2/Pallet ITEMPNĞƐĐƌŝƉƟŽŶQty A4ƉĂůůĞƚůĂďĞů 1.1 21.4 3 All Label position Add one layer film cover on the pallet label sheet CQA must double check all the status of pallet label sheet before shipping. the outside one layer film don’t cover the open side fo A4 sheet Customer Pallet label (2pcs/pallet) Label shall be placed on two opposite sides of the pallet center open of A4 sheet U 1.5 It must be inserted into the STB PE bag (at the bottom of STB) · Warranty Seal label shall be affixed in such a way that it covers one screw and hidden by rubber foot. · STB Housing Serialization Label - the label is affixed to the bottom of product casing in the dedicated area, please make sure that the label does not cover ventilation holes. · STB Housing WIFI Label - it applies ONLY to 1761WF variant; the label is affixed to the bottom of product casing in the dedicated area, please make sure that the label does not cover ventilation holes. 1.21.3 Open side T T ,ULV 6XQQ\ 3. ,; ,1ODEHO  $'%:)1$  ,ULV )LUVWUHOHDVH 1RWH ODEHOPDWHULDOLVP\ODU PDWWH 3(7 PDWWH 6XUIDFH0DWHULDO P\ODU PDWWH WKLFNQHVVPP 3(7 PDWWH WKLFNQHVVPP $GKHVLYHLVHPERVVLQJ ວ㢅㝴 $GKHVLYHWKLFNQHVVPP $GKHVLRQWRVWHHOaNJLQFK ,QLWLDO7DFNa +ROGLQJ3RZHUKUNJ LQFK EDFNJURXQGFRORU:KLWH 3ULQWFRORU%ODFN SDFNDJHEDJPXVWFRQWDLQ8/LQIRUPDWLRQ P\ODU PDWWH 3(7 PDWWH )R[FRQQSULQW 7KHODEHOGHILQDWLRQVHHWKHQH[WSDJH ߎ ㋭ ᮍ ৥ 9HQGRUVXSSO\6L]HGHWDLO FCC ID: MCLADB1761WF ADB-1761WF manufactured by Advanced Digital Broadcast Serial n°: AAAAXXXYWWXPPPPPP Made in XXXX ADBA-SX14015A P/N: 151160601 Rating: 12V 2.5ALot N°: S-ww/yy of: dd.mm.yy Factory ID: X I.T.E. E199598 8G92 MAC ETH: XX:XX:XX:XX:XX:XX MAC WiFi CL: XX:XX:XX:XX:XX:XX MAC WiFi AP: XX:XX:XX:XX:XX:XX This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,and (2) this device must accept any interference received,including interference that may cause undesired operation. Serial n°. Barcode MAC Addr. Barcode ADB-1761WF Made in XXXX manufactured by Advanced Digital Broadcast ADBA-SX14015A Lot N°: S-ww/yy of: dd.mm.yy P/N: 151160601 I.T.E. E199598 8G92 Factory ID: X MAC ETH: XX:XX:XX:XX:XX:XX MAC WiFi CL: XX:XX:XX:XX:XX:XX MAC WiFi AP: XX:XX:XX:XX:XX:XX MAC Addr. Barcode Serial n°: AAAAXXXYWWXPPPPPP Serial n°. Barcode Rating: 12V 2.5A FCC ID: MCLADB1761WF ד㰩ৃᩩ䭟 WPA2: xxxxxxxxxxxxxxxx SSID: BFZH-xxxxxx IRQW9(5'$1$SW WPA2: xxxxxxxxxxxxxxxx SSID: BFZH-xxxxxx   IRQW9(5'$1$SW  %DUFRGHW\SH($1 IRQW$ULDO,WDOLFSW IRQW$ULDO%ROGSW IRQW0\ULDG5RPDQSW $      % ˄IRQW$ULDO5HJXODUSW   I01X108.00 LF MO-VVSS    IRQW$ULDOQDUURZ%ROGSW )&&:DUQLQJIRQW$ULDO%ROGSW 9HQGRUFRGH IRQW$ULDO%ROGSW IRQW$ULDO,WDOLFSW 9HQGRUFRGH I01X108.00 LF MO-VVSS I.T.E. E199598 8G92 I.T.E. E199598 8G92 ד㰩ৃᩩ䭟 9HQGRUFRGH 9HQGRUFRGH Manufactured under license from Dolby Laboratories. “Dolby”and the double-D symbol are trademarks of Dolby Laboratories. (Fig. 1) FCC ID: MCLADB1761WF FCC LABEL LOCATION The label will be permanently affixed at a conspicuous location on the device. Label

Report No.: 150407E02 Page 1 CONSTRUCTION PHOTOS OF EUT Report No.: 150407E02 Page 2 Report No.: 150407E02 Page 3 Report No.: 150407E02 Page 4 Report No.: 150407E02 Page 5 Report No.: 150407E02 Page 6 Report No.: 150407E02 Page 7 Report No.: 150407E02 Page 8

FCC ID: MCLADB1761WF Report No.: RF150407E02 Operational Description This device is a IP Set-Top Box with Wi-Fi 11ac, which operates in Z-Wave technology and WLAN (2.4GHz & 5GHz), and can transmitting simultaneously. The maximum data rate could be up to 1733.3Mbps which OFDM technique. If the signal to noise radio is too poor which could not support 1733.3Mbps. The transmitter of the EUT is powered by DC 12V from power adapter. The antennas provided to the EUT, please refer to the following table: The other instruction, please have a look at the users manual. FCC 15.407(c) states: The device shall automatically discontinue transmission in case of either absence of information to transmit or operational failure. These provisions are not intended to preclude the transmission of control or signaling information or the use of repetitive codes used by certain digital technologies to complete frame or burst intervals. Applicants shall include in their application for equipment authorization a description of how this requirement is met” Data transmission is always initiated by software, which is then pass down through the MAC, through the digital and analog baseband, and finally to the RF chip. Several special packets (ACKs, CTS, PSPoll, etc...) are initiated by the MAC. There are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only while one of the aforementioned packets are being transmitted.

HON HAI PRECISION IND. CO., LTD. 5F-1,5 Hsin-An Road Hsinchu, Science-Based Industrial Park Taiwan, R.O.C. Date: 2015-06-04 FCC ID: MCLADB1761WF Software Operational Description We, HON HAI PRECISION IND. CO., LTD. hereby declare that requirements of KDB594280 have been met and shown on the following question. SOFTWARE SECURITY DESCRIPTION General Description 1. Describe how any software/firmware update will be obtained, downloaded, and installed. Description: (1) Obtain and download The firmware could be obtained from specific site of internet. (2) Install The product will install new firmware by setup menu or automatically. 2. Describe all the radio frequency parameters that are modified by any software/firmware without any hardware changes. Are these parameters in some way limited, such that, it will not exceed the authorized parameters? Description: Only two radio frequency parameters, Channel and Channel Bandwidth, can be configured via UI: . All above parameters are pre-installed and cannot be configured. 3. Are there any authentication protocols in place to ensure that the source of the software/firmware is legitimate? If so, describe in details; if not, explain how the software is secured from modification. Description: Firmware has a private signature inside. If firmware is modified, then it cannot be allowed to be upgraded. 4. Are there any verification protocols in place to ensure that the software/firmware is legitimate? If so, describe in details. Description: Firmware has a private signature inside. If firmware is modified, then it cannot be allowed to be upgraded. 5. Describe, if any, encryption methods used. Description: HON HAI PRECISION IND. CO., LTD. 5F-1,5 Hsin-An Road Hsinchu, Science-Based Industrial Park Taiwan, R.O.C. Not Supported 6. For a device that can be configured as a master and client (with active or passive scanning), explain how the device ensures compliance for each mode? In particular if the device acts as master in some band of operation and client in another; how is compliance ensured in each band of operation? Description: Our device works as following configuration: 2412-2462MHz : active and passive scan 5180-5240 / 5745-5825MHz : active and passive scan 5260-5340 / 5500-5700MHz : passive scan only This configuration is pre-installed and cannot be configured. Third-Party Access Control 1. How are unauthorized software/firmware changes prevented? Description: Our software/firmware has a private signature inside. If firmware is modified, then it cannot be allowed to be upgraded. 2. Is it possible for third parties to load device drivers that could modify the RF parameters, country of operation or other parameters which impact device compliance? If so, describe procedures to ensure that only approved drivers are loaded. Description: It is impossible. Our software/firmware has a private signature inside. If firmware is modified, then it cannot be allowed to be upgraded. 3. Explain if any third parties have the capability to operate a US sold device on any other regulatory domain, frequencies, or in any manner that is in violation of the certification. Description: The parameters of country, frequencies and etc. are permanent settings and cannot be configured. The device can operate only at authorized frequencies and bandwidth. 4. What prevents third parties from loading non-US versions of the software/firmware on the device? Description: The parameters of country, frequencies and etc. are permanent settings and cannot be configured. 5. For modular devices, describe how authentication is achieved when used with different hosts. Description: Our device has proprietary value and cannot work on other hosts. SOFTWARE CONFIGURATION DESCRIPTION HON HAI PRECISION IND. CO., LTD. 5F-1,5 Hsin-An Road Hsinchu, Science-Based Industrial Park Taiwan, R.O.C. USER CONFIGURATION GUIDE 1. To whom is the UI accessible? (Professional installer, end user, other...) a) What parameters are viewable to the professional installer/end‐user? Description: Both professional and end user cannot see any RF parameters, other than frequency channel setting and RSSI. b) What parameters are accessible or modifiable to the professional installer? Description: Both professional and end user cannot access any RF parameters, other than frequency channel setting and RSSI. They can select frequency channel from authorized frequency channels list. i) Are the parameters in some way limited, so that the installers will not enter parameters that exceed those authorized? Description: Both professional and end user cannot access any RF parameters, other than frequency channel setting and RSSI. They can select frequency channel from authorized frequency channels list. ii) What controls exist that the user cannot operate the device outside its authorization in the U.S.? Description: The parameters of country, frequencies and etc. are permanent settings and cannot be configured. c) What configuration options are available to the end‐user Description: The end user can select frequency channel from authorized frequency channels list. i) Are the parameters in some way limited, so that the installers will not enter parameters that exceed those authorized? Description: The installers can select frequency channel from authorized frequency channels list. ii) What controls exist that the user cannot operate the device outside its authorization in the U.S.? Description: The parameters of country, frequencies and etc. are permanent settings and cannot be configured. d) Is the country code factory set? Can it be changed in the UI? Description: It is factory set and cannot be changed in the UI. i) If so, what controls exist to ensure that the device can only operate within its authorization in the U.S.? Description: The parameters of country, frequencies and etc. are permanent settings and cannot be configured. e) What are the default parameters when the device is restarted? HON HAI PRECISION IND. CO., LTD. 5F-1,5…

Text truncated - open the document above for the full version.

Report No.: SA150407E02 Page No. 1 / 9 Report Format Version: 6.1.1 RF Exposure Report Report No.: SA150407E02 Compliance ID : ADBA-SX14015A Product Name* : ADB-1761WF *For any other product variant refer to above Compliance ID FCC ID: MCLADB1761WF Received Date: Feb. 11, 2015 Test Date: Apr. 24 to May 09, 2015 Issued Date: May 28, 2015 Applicant: HON HAI PRECISION IND. CO., LTD. Address: 5F-1,5 Hsin-An Road Hsinchu, Science-Based Industrial Park Taiwan, R.O.C. Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory Lab Address: No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan R.O.C. Test Location (1): No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan R.O.C. Test Location (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by any government agencies. Report No.: SA150407E02 Page No. 2 / 9 Report Format Version: 6.1.1 Table of Contents Release Control Record .................................................................................................................................. 3 1 Certificate of Conformity ...................................................................................................................... 4 2 RF Exposure .......................................................................................................................................... 5 2.1 Limits for Maximum Permissible Exposure (MPE) .............................................................................. 5 2.2 MPE Calculation Formula ................................................................................................................... 5 2.3 Classification ....................................................................................................................................... 5 2.4 Antenna Gain ...................................................................................................................................... 6 3 Calculation Result Of Maximum Conducted Power .......................................................................... 7 Report No.: SA150407E02 Page No. 3 / 9 Report Format Version: 6.1.1 Release Control Record Issue No. Description Date Issued SA150407E02 Original release. May 28, 2015 Report No.: SA150407E02 Page No. 5 / 9 Report Format Version: 6.1.1 2 RF Exposure 2.1 Limits for Maximum Permissible Exposure (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (minutes) Limits For General Population / Uncontrolled Exposure 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 2.2 MPE Calculation Formula Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm 2.3 Classification The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. Report No.: SA150407E02 Page No. 6 / 9 Report Format Version: 6.1.1 2.4 Antenna Gain 1. The antennas provided to the EUT, please refer to the following table: Zigbee Antenna No. Transmitter Circuit Brand Model Ant. Gain(dBi) <Including cable loss> Frequency range (GHz to GHz) Antenna Type Connecter Type 1 Chain (0) INPAQ NA 2.78 2.4~2.5 PIFA NA 2 Chain (1) NA 2.45 2.4~2.5 5GHz Band Antenna No. Transmitter Circuit Brand Model Ant. Gain(dBi) <Including cable loss> Frequency range (GHz to GHz) Antenna Type Connecter Type 1 Chain (0) TONGDA COMMUNICAT ION CO., LTD. NA 3.49 5.15~5.25 PCB i-pex(MHF) NA 3.99 5.725~5.85 PCB i-pex(MHF) 2 Chain (1) NA 3.47 5.15~5.25 PCB i-pex(MHF) NA 4.57 5.725~5.85 PCB i-pex(MHF) 3 Chain (2) NA 4.11 5.15~5.25 PCB i-pex(MHF) NA 3.7 5.725~5.85 PCB i-pex(MHF) 4 Chain (3) NA 3.45 5.15~5.25 PCB i-pex(MHF) NA 3.46 5.725~5.85 PCB i-pex(MHF) Report No.: SA150407E02 Page No. 7 / 9 Report Format Version: 6.1.1 3 Calculation Result Of Maximum Conducted Power For WLAN CDD MODE 802.11a Frequency Band (MHz) Max Power (mW) Antenna Gain (dBi) Distance (cm) Power Density (mW/cm 2 ) Limit (mW/cm 2 ) 5180-5240 274.648 9.66 20 0.50525 1 5745-5825 217.062 9.96 20 0.42787 1 NOTE: 5150~5250MHz: Directional gain = 10 log[(10 G1/20 + 10 G2/20 + 10 G3/20 + 10 G4/20 ) 2 / 4] = 9.66dBi 5725~5825MHz: Directional gain = 10 log[(10 G1/20 + 10 G2/20 + 10 G3/20 + 10 G4/20 ) 2 / 4] = 9.96dBi 802.11ac (VHT20) Frequency Band (MHz) Max…

Text truncated - open the document above for the full version.

Report No.: RF150407E02 Page No. 1 / 81 Report Format Version:6.1.1 FCC Test Report (WLAN) Report No.: RF150407E02 Compliance ID : ADBA-SX14015A Product Name* : ADB-1761WF *For any other product variant refer to above Compliance ID FCC ID: MCLADB1761WF Received Date: Feb. 11, 2015 Test Date: Feb. 11 to May 11, 2015 Issued Date: May 28, 2015 Applicant: HON HAI PRECISION IND. CO., LTD. Address: 5F-1,5 Hsin-An Road Hsinchu, Science-Based Industrial Park Taiwan, R.O.C. Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory Lab Address: No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan R.O.C. Test Location (1): No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan R.O.C. Test Location (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report must not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF150407E02 Page No. 2 / 81 Report Format Version:6.1.1 Table of Contents Release Control Record .................................................................................................................................. 4 1 Certificate of Conformity ...................................................................................................................... 5 2 Summary of Test Results ..................................................................................................................... 6 2.1 Measurement Uncertainty ................................................................................................................... 6 2.2 Modification Record ............................................................................................................................ 6 3 General Information .............................................................................................................................. 7 3.1 General Description of EUT (WLAN) .................................................................................................. 7 3.2 Description of Test Modes ................................................................................................................... 9 3.2.1 Test Mode Applicability and Tested Channel Detail ........................................................................... 10 3.3 Duty Cycle of Test Signal ..................................................................................................…

Text truncated - open the document above for the full version.