MCLCSE300APK9Cisco Edge 300

Americas Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA Cisco Edge 300 Series Switch Installation Guide •About this Guide, page 1 •Box Contents, page 2 •Overview, page 3 •Installing the Switch, page 6 •Powering on the Switch, page 15 •Restoring the Factory Settings, page 15 •Technical Specifications, page 15 •Obtaining Documentation and Submitting a Service Request, page 16 About this Guide This guide describes how to install the Cisco Edge 300 series switch on a wall or desktop and describes the LEDs and ports. For configuration information, see the Cisco Edge 300 series switch documentation on Cisco.com. For system requirements, important notes, limitations, open and resolved bugs, and documentation updates, see the release notes on Cisco.com. 2 Cisco Edge 300 Series Switch Installation Guide OL-24909-01 Box Contents Box Contents NoteVerify that you have received these items. If any item is missing or damaged, contact your Cisco representative or reseller. 1Cisco Edge 300 series switch7Four M3.5 x 16-mm Phillips head tapping screws 1 2Power adapter8Four plastic drywall anchors 1 3Power cord9Cable tie 1, 2 4Power cord retainer 1, 2 1. These parts are included in the wall-mount kit (ACC-E300-WALL). 2. These parts are included in the desktop kit (ACC-E300-DESK). 10Desktop bracket 2 5Wall-mount bracket 1 11Two M3.0 x 6-mm Phillips pan head screws 2 6Four M3.0 x 6-mm Phillips pan head screws 1 1 2 3 4 5 678 9 10 11 9 3 Cisco Edge 300 Series Switch Installation Guide OL-24909-01 Overview Overview Figure 1Cisco Edge 300 Series Switch — Front Figure 2Cisco Edge 300 Series Switch — Left Figure 3Cisco Edge 300 Series Switch — Rear Table 1Cisco Edge 300 Series Models ModelDescription CS-E300-AP-K9Cisco Edge 300 series switch with WiFi and Bluetooth CS-E300-K9Cisco Edge 300 series switch HS-E300-AP-K9HSJC/Cisco Edge 300 series switch with WiFi and Bluetooth HS-E300-K9HSJC/Cisco Edge 300 series switch 1USB ports5Gigabit Ethernet (uplink) port 2HDMI port6Ethernet (downlink) ports 3Audio out port7Power 4Audio in port POWER 1 234 GE HDMI 255417 2 1 3457 6 1USB port 255418 1 1Power button2Reset button 255419 RESET 12 4 Cisco Edge 300 Series Switch Installation Guide OL-24909-01 Overview Port Descriptions USB There are four USB 2.0 Type-A ports. Each USB port can provide up to 5 W of power to a connected device. You can connect a wired USB keyboard and mouse, a wireless USB receiver for a keyboard and mouse, a USB camera, or a USB thumb drive. HDMI The HDMI port supports high-definition video output at 720p or 1080p. Audio In You can connect a microphone that uses a 3.5 mm connector. Audio Out You can connect headphones or external speakers that use a 3.5 mm connector. Gigabit Ethernet The Gigabit Ethernet uplink port provides a 10/100/1000 Mb/s connection to a Catalyst 2000 or Catalyst 3000 series switch. Ethernet The Fast Ethernet ports provide 10/100 Mb/s connections to computers or other devices. Wireless Features WiFi Supports 802.11b/g/n wireless clients. Bluetooth Supports Human Interaction Design Protocol (HIDP) for remote control or input devices. 5 Cisco Edge 300 Series Switch Installation Guide OL-24909-01 Overview LEDs Figure 4Cisco Edge 300 Series Switch LEDs 1Ethernet downlink4Bluetooth 1 2Gigabit Ethernet uplink5Power 3WiFi 1 1. Only CS-E300-AP-K9 and HS-E300-AP-K9. Ta b l e 2L E D s LEDColorMeaning Ethernet downlink OffNo link. GreenLink present, no activity. Port is operating at 100 Mb/s. Blinking greenActivity. Port is sending or receiving data at 100 Mb/s. AmberLink present, no activity. Port is operating at 10 Mb/s. Blinking amber Activity. Port is sending or receiving data at 10 Mb/s. Gigabit Ethernet OffNo link. GreenLink up. Blinking greenActivity. 255420 R 1 234 R 1 234 5 5 2 1 345 6 Cisco Edge 300 Series Switch Installation Guide OL-24909-01 Installing the Switch Installing the Switch You can install the switch on a wall by using the wall-mount bracket or install the switch on a desk or table by using the desktop bracket. You can also install the switch in a ventilated cabinet using the wall-mount or desktop bracket. Equipment That You Need •Phillips screwdriver •Scratch awl or other sharp pointed object (wall-mount) •Electric drill with a 6-mm drill bit (wall-mount) Before You Begin Before installing the switch, verify that these guidelines are met: •Front clearance so that the LEDs can be seen. •AC power cord reaches from the AC power outlet to the rear-panel connector. •Cabling is away from sources of electrical noise, such as radios, power lines, and fluorescent lighting. Make sure that the cabling is safely away from other devices that might damage the cables. •Airflow around the switch is unrestricted. •Temperature around the unit does not exceed 104°F (40°C). •Humidity around the switch does not exceed 85 percent. •Altitude at the installation site is below 10,000 feet. •For Ethernet ports, cables from the switch to connected devices are not longer than 328 feet (100 meters). WiFiOffWiFi is disabled. GreenWiFi is enabled and functioning. Blinking greenWiFi is transmitting data. BluetoothOffBluetooth is disabled. GreenBluetooth is enabled and functioning. PowerOffThere is no power or the self test has failed. GreenSystem is operating normally. Blinking greenSystem software is being upgraded. Blinking amber System software download has failed. Table 2LEDs (continued) LEDColorMeaning 7 Cisco Edge 300 Series Switch Installation Guide OL-24909-01 Installing the Switch Warning Statements Statement 1005 WarningThis product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 20A Statement 1005 Statement 1071 Statement 1019 WarningThe plug-socket combination must be accessible at all times, because it serves as the main disconnecting device. Statement 1019 Statement 1030 WarningOnly trained and qualified personnel should be allowed to install, replace, …

Text truncated - open the document above for the full version.

HON HAI Precision Ind. Co., Ltd. Model Declaration Letter We, the undersigning company Name: HON HAI Precision Ind. Co., Ltd. Address: 5F-1, 5, Hsin-An Road, Hsinchu Science-Based Industrial Park Hereby confirm that the following products: Product description: Cisco Edge 300 Type designation: CS-E300-AP-K9, HS-E300-AP-K9 Brand: Cisco All versions of the Model CS-E300-AP-K9 and HS-E300-AP-K9 are electrically equal and only differ is for different customer usage. Company Name: HON HAI Precision Ind. Co., Ltd. Address: 5F-1, 5, Hsin-An Road, Hsinchu Science-Based Industrial Park Telephone +886-3-5784975 Fax No.: +886-3-5775100 E-mail: [email protected] Signature: ________________________ Name: Mrs. Rio Chen

RF_160, Issue 02 Declaration of Authorization We Name: HON HAI Precision Ind. Co., Ltd. Address: 5F-1, 5, Hsin-An Road, Hsinchu Science-Based Industrial Park City: Hsinchu Country: Taiwan Declare that: Name Representative of agent: Ms. Cathy Wang Agent Company name: Neutron Engineering, Inc. Address: No.3 Jinshagang 1 st Road, Shixia, Dalang Town City: Dongguan Country: China is authorized to apply for Certification of the following product(s): Product description: Cisco Edge 300 Type designation: Cisco Trademark: CS-E300-AP-K9, HS-E300-AP-K9 on our behalf. Date: 2011-09-02 City: Hsinchu Name: Mrs. Rio Chen Function: Compliance Deputy Manager Signature: .............................. . Notes: (1): Required for FCC application (2): For FCC it must be the Grantee Code “owner” or the authorized agent.

FCC, Request for non-disclosure Date: 10-AUG-09 RF_501, Issue 5 Page 1 of 1 Company Name: HON HAI Precision Ind. Co., Ltd. Address: 5F-1, 5, Hsin-An Road, Hsinchu Science-Based Industrial Park City: Hsinchu Country: Taiwan To: Telefication B.V., Dept. FCC TCB Edisonstraat 12A 6902 PK ZEVENAAR The Netherlands Subject: Request for confidentiality FCC ID: MCLCSE300APK9 Reference number: CS-E300-AP-K9, HS-E300-AP-K9 Dear FCC TCB, 1. Long-Term Confidentiality Pursuant to 47 CFR Section 0.459(a) & (b), we hereby requests non-disclosure and confidential treatment of the following materials submitted in support of FCC certification application: Bill(s) of Material Block Diagrams Operational Description Schematic Diagrams Tune-up Procedure Above materials contain secrets, proprietary and technical information, which would customarily be guarded from competitors under 47 CFR, section 0.457(d)(2). Disclosure or publication or any portion of this company confidential material to other parties could cause substantial competitive harm and provide unjustified benefits for competitors. 2. Short-Term Confidentiality (STC) Pursuant to Public Notice DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, applicant hereby requests Short-Term Confidential treatment of the following materials (note 1): Internal Photos User’s Manual Test Set-up Photos External Photos Justification: Planned Release Date STC: (notes 2, 3, 4, 5) Date: 2011-09-02 Name and signature of applicant: Mrs. Rio Chen Notes: 1) A document or type of document can only have ONE type of confidentiality! 2) Short-Term confidentiality is in principle for 45 days from date of grant; it can be extended max 3 times (total time 180 days max.)! 3) FCC must be informed when marketing begins earlier. 4) Release takes place automatically thus extension must be requested in time. Telefication does not remind you of this! 5) Request for extension or for release must be received by Telefication at least 7 days before date of actual marketing or before expiration of the STC period

Neutron Engineering Inc. Project No.: 1108C254 Page 2 of 19 1108C254 1108C254 Neutron Engineering Inc. Project No.: 1108C254 Page 2 of 19 1108C254 1108C254 Neutron Engineering Inc. Project No.: 1108C254 Page 3 of 19 1108C254 1108C254 Neutron Engineering Inc. Project No.: 1108C254 Page 3 of 19 1108C254 1108C254 Neutron Engineering Inc. Project No.: 1108C254 Page 4 of 19 1108C254 1108C254 Neutron Engineering Inc. Project No.: 1108C254 Page 4 of 19 1108C254 1108C254 Neutron Engineering Inc. Project No.: 1108C254 Page 5 of 19 1108C254 1108C254 Neutron Engineering Inc. Project No.: 1108C254 Page 5 of 19 1108C254 1108C254

CMIIT ID:2011DJ2744 CS-E300-AP-K9 CS-E300-AP-K9 Cisco Brand - WIFI CS-E300-K9 Cisco Brand - non-WIFI HS-E300-AP-K9 Co Brand - WIFI HS-E300-K9 Co Brand - non-WIFI 12V 5A Cisco Edge 300 Cisco Systems, Inc. 110 80 50.00 PID VID : CS-E300-AP-K9 V01 SN : FOCxxxxxxxx TAN : 74-9128-01 A0 XXXXXXXXXXXX FCC ID: MCLCSE300APK9 This equipment complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions: (1) This device may not cause harmful interference,and (2) This device must accept any interference received, including interference that may cause undesired operation CS-E300-K9 12V 5A Cisco Edge 300 Cisco Systems, Inc. PID VID : CS-E300-K9 V01 SN : FOCxxxxxxxx TAN : 74-9683-01 A0 XXXXXXXXXXXX CMIIT ID:2011DJ2745 HS-E300-AP-K9 12V 5A Cisco Edge 300 Cisco Systems, Inc. PID VID : HS-E300-AP-K9 V01 SN : FOCxxxxxxxx TAN : 74-9702-01 A0 XXXXXXXXXXXX HS-E300-K9 12V 5A Cisco Edge 300 Cisco Systems, Inc. PID VID : HS-E300-K9 V01 SN : FOCxxxxxxxx TAN : 74-9703-01 A0 XXXXXXXXXXXX CMIIT ID:2011XXXXXX HS-E300-AP-K9 12V 5A Cisco Edge 300 Cisco Systems, Inc. PID VID : HS-E300-AP-K9 V01 SN : FOCxxxxxxxx TAN : 74-9128-01 A0 XXXXXXXXXXXX Compliance label Bottom view

Neutron Engineering Inc. Project No.: 1108C254 Page 6 of 19 1108C254 1108C254 Neutron Engineering Inc. Project No.: 1108C254 Page 6 of 19 1108C254 1108C254 Neutron Engineering Inc. Project No.: 1108C254 Page 7 of 19 1108C254 1108C254 Neutron Engineering Inc. Project No.: 1108C254 Page 7 of 19 1108C254 1108C254 Neutron Engineering Inc. Project No.: 1108C254 Page 8 of 19 1108C254 1108C254 Neutron Engineering Inc. Project No.: 1108C254 Page 8 of 19 1108C254 1108C254 Neutron Engineering Inc. Project No.: 1108C254 Page 9 of 19 1108C254 1108C254 Neutron Engineering Inc. Project No.: 1108C254 Page 9 of 19 1108C254 1108C254 Neutron Engineering Inc. Project No.: 1108C254 Page 10 of 19 1108C254 1108C254 Neutron Engineering Inc. Project No.: 1108C254 Page 10 of 19 1108C254 1108C254 Neutron Engineering Inc. Project No.: 1108C254 Page 11 of 19 1108C254 1108C254 Neutron Engineering Inc. Project No.: 1108C254 Page 11 of 19 1108C254 1108C254 Neutron Engineering Inc. Project No.: 1108C254 Page 12 of 19 1108C254 1108C254 Neutron Engineering Inc. Project No.: 1108C254 Page 12 of 19 1108C254 1108C254 Neutron Engineering Inc. Project No.: 1108C254 Page 13 of 19 1108C254 1108C254 Neutron Engineering Inc. Project No.: 1108C254 Page 13 of 19 1108C254 1108C254 Neutron Engineering Inc. Project No.: 1108C254 Page 14 of 19 1108C254 1108C254 Neutron Engineering Inc. Project No.: 1108C254 Page 14 of 19 1108C254 1108C254 Neutron Engineering Inc. Project No.: 1108C254 Page 15 of 19 1108C254 1108C254 Neutron Engineering Inc. Project No.: 1108C254 Page 15 of 19 1108C254 1108C254 Neutron Engineering Inc. Project No.: 1108C254 Page 16 of 19 1108C254 1108C254 Neutron Engineering Inc. Project No.: 1108C254 Page 16 of 19 1108C254 1108C254 Neutron Engineering Inc. Project No.: 1108C254 Page 17 of 19 1108C254 1108C254 Neutron Engineering Inc. Project No.: 1108C254 Page 17 of 19 1108C254 1108C254 Neutron Engineering Inc. Project No.: 1108C254 Page 18 of 19 1108C254 1108C254 Neutron Engineering Inc. Project No.: 1108C254 Page 18 of 19 1108C254 1108C254 Neutron Engineering Inc. Project No.: 1108C254 Page 19 of 19 1108C254

Neutron Engineering Inc. FCC RF EXPOSURE REPORT FCC ID: MCLCSE300APK9 Project No. : 1108C254 Equipment : Cisco Edge 300 Model : CS-E300-AP-K9, HS-E300-AP-K9 Applicant : HON HAI Precision Ind. Co., Ltd. Address : 5F-1, 5, Hsin-An Road,Hsinchu Science-Based Industrial Park According: : FCC Guidelines for Human Exposure IEEE C95.1 Neutron Engineering Inc. No.3, Jinshagang 1st Road, ShiXia, Dalang Town, Dong Guan, China. TEL : (0769) 8318-3000 FAX : (0769) 8319-6000 Neutron Engineering Inc. MPE CALCULATION METHOD: Calculation Method of RF Safety Distance: where: S = power density P = power input to the antenna G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna Ant. Brand name Model Name Antenna TypeConnector Gain (dBi) cable length 1 FOXCONN FX01B88-O G-EF-H PCB U.FL 3.10 41 mm TEST RESULTS EUT： Cisco Edge 300 Model Name ： AD7000W/37 Temperature： 25 °C Relative Humidity： 60 % Pressure： 1012 hPa Test Voltage ： AC 120V/60Hz Test Mode ： CH00/ CH39 /CH78 -1Mbps Antenna Gain (dBi) Antenna Gain (numeric) Peak Output Power (dBm) Peak Output Power (mW) Power Density (S) (mW/cm 2 ) Limit of Power Density (S) (mW/cm 2 ) Te s t Result 3.10 2.0417 -0.31 0.9311 0.000378401 Complies 3.10 2.0417 1.93 1.5596 0.000633801 Complies 3.10 2.0417 -0.41 0.9099 0.000369791 Complies Neutron Engineering Inc. EUT： Cisco Edge 300 Model Name ： CS-E300-AP-K9 Temperature： 25 °C Relative Humidity： 60 % Pressure： 1012 hPa Test Voltage ： AC 120V/60Hz Test Mode ： CH00/ CH39 /CH78 -1Mbps Antenna Gain (dBi) Antenna Gain (numeric) Peak Output Power (dBm) Peak Output Power (mW) Power Density (S) (mW/cm 2 ) Limit of Power Density (S) (mW/cm 2 ) Te s t Result 3.10 2.0417 2.77 1.8923 0.000769041 Complies 3.10 2.0417 3.02 2.0045 0.000814611 Complies 3.10 2.0417 2.57 1.8072 0.000734431 Complies

Neutron Engineering Inc. Report No.: NEI-FCCP-1-1108C254 Page 1 of 99 FCC Radio Test Report FCC ID: MCLCSE300APK9 This report concerns (check one) : Original Grant Class II Change Issued Date : Sep. 01, 2011 Project No. : 1108C254 Equipment : Cisco Edge 300 Model Name : CS-E300-AP-K9;HS-E300-AP-K9 Applicant : Hon Hai Precision Ind., Co.,Ltd. Address : 5F-1, 5, Hsin-An Road, Hsinchu Science-Based Industrial Park Hsinchu Taiwan Manufacturer : Cisco Systems, Inc. Address : 170 West Tasman Drive, San Jose，CA 95134-1706 U.S.A Testing Engineer : (Ivan Cao) Technical Manager : (Leo Hung) Authorized Signatory : (Steven Lu) Neutron Engineering Inc. No.3,Jinshagang 1st Road, ShiXia, Dalang Town, Dong Guan, China. TEL : (0769) 8318-3000 FAX : (0769) 8319-6000 Tested by: Neutron Engineering Inc. EMC Laboratory Date of Receipt: Aug. 10, 2011 Date of Test: Aug. 10, 2011 ~ Aug. 31, 2011 Neutron Engineering Inc. Report No.: NEI-FCCP-1-1108C254 Page 2 of 99 Declaration Neutron represents to the client that testing is done in accordance with standard procedures as applicable and that test instruments used has been calibrated with the standards traceable to National Measurement Laboratory (NML) of R.O.C., or National Institute of Standards and Technology (NIST) of U.S.A. Neutron's reports apply only to the specific samples tested under conditions. It is manufacture’s responsibility to ensure that additional production units of this model are manufactured with the identical electrical and mechanical components. Neutronshall have no liability for any declarations, inferences o r generalizations drawn by the client or others from Neutron issued reports. Neutron’s reports must not be used by the client to claim product endorsement by the authorities or any agency of the Government. This report is the confidential property of the client. As a mutual protection to the clients, the public and Neutron-self, extracts from the test report shall not be reproduced except in full with Neutron’s authorized written approval. Neutron’s laboratory quality assurance procedures are in compliance with the ISO Guide 17025 requirements, and accredited by the conformity assessment authorities listed in this test report. Limitation For the use of the authority's logo is limited unless the Test Standard(s)/Scope(s)/Item(s) mentioned in this test report is (are) included in the conformity assessment authorities acceptance respective. Neutron Engineering Inc. Report No.: NEI-FCCP-1-1108C254 Page 3 of 99 Table of Contents Page 1 . CERTIFICATION 6 2 . SUMMARY OF TEST RESULTS 7 2.1 TEST FACILITY 8 2.2 MEASUREMENT UNCERTAINTY 8 3 . GENERAL INFORMATION 9 3.1 GENERAL DESCRIPTION OF EUT 9 3.2 DESCRIPTION OF TEST MODES 11 3.3 TABLE OF PARAMETERS OF TEXT SOFTWARE SETTING 11 3.4 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 12 3.5 DESCRIPTION OF SUPPORT UNITS (CONDUCTED MODE) 13 4 . EMC EMISSION TEST 14 4.1 CONDUCTED EMISSION MEASUREMENT 14 4.1.1 POWER LINE CONDUCTED EMISSION LIMITS 14 4.1.2 MEASUREMENT INSTRUMENTS LIST AND SETTING 14 4.1.3 TEST PROCEDURE 15 4.1.4 DEVIATION FROM TEST STANDARD 15 4.1.5 TEST SETUP 15 4.1.6 EUT OPERATING CONDITIONS 16 4.1.7 TEST RESULTS 17 4.2 RADIATED EMISSION MEASUREMENT 21 4.2.1 RADIATED EMISSION LIMITS 21 4.2.2 MEASUREMENT INSTRUMENTS LIST ANS SETTING 22 4.2.3 TEST PROCEDURE 23 4.2.4 DEVIATION FROM TEST STANDARD 23 4.2.5 TEST SETUP 24 4.2.6 EUT OPERATING CONDITIONS 24 4.2.7 TEST RESULTS (BETWEEN30 – 1000 MHZ) 25 4.2.8 TEST RESULTS (ABOVE 1000 MHZ) 29 5 . NUMBER OF HOPPING CHANNEL 53 5.1 APPLIED PROCEDURES / LIMIT 53 5.1.1 MEASUREMENT INSTRUMENTS LIST AND SETTING 53 5.1.2 TEST PROCEDURE 53 5.1.3 DEVIATION FROM STANDARD 53 5.1.4 TEST SETUP 53 5.1.5 EUT OPERATION CONDITIONS 53 5.1.6 TEST RESULTS 54 Neutron Engineering Inc. Report No.: NEI-FCCP-1-1108C254 Page 4 of 99 Table of Contents Page 6 . AVERAGE TIME OF OCCUPANCY 56 6.1 APPLIED PROCEDURES / LIMIT 56 6.1.1 MEASUREMENT INSTRUMENTS LIST 56 6.1.2 TEST PROCEDURE 56 6.1.3 DEVIATION FROM STANDARD 56 6.1.4 TEST SETUP 57 6.1.5 EUT OPERATION CONDITIONS 57 6.1.6 TEST RESULTS 58 7 . HOPPING CHANNEL SEPARATION MEASUREMENT 70 7.1 APPLIED PROCEDURES / LIMIT 70 7.1.1 MEASUREMENT INSTRUMENTS LIST AND SETTING 70 7.1.2 TEST PROCEDURE 70 7.1.3 DEVIATION FROM STANDARD 70 7.1.4 TEST SETUP 70 7.1.5 EUT OPERATION CONDITIONS 70 7.1.6 TEST RESULTS 71 8 . BANDWIDTH TEST 75 8.1 APPLIED PROCEDURES / LIMIT 75 8.1.1 MEASUREMENT INSTRUMENTS LIST AND SETTING 75 8.1.2 TEST PROCEDURE 75 8.1.3 DEVIATION FROM STANDARD 75 8.1.4 TEST SETUP 75 8.1.5 EUT OPERATION CONDITIONS 75 8.1.6 TEST RESULTS 76 9 . PEAK OUTPUT POWER TEST 80 9.1 APPLIED PROCEDURES / LIMIT 80 9.1.1 MEASUREMENT INSTRUMENTS LIST AND SETTING 80 9.1.2 TEST PROCEDURE 80 9.1.3 DEVIATION FROM STANDARD 80 9.1.4 TEST SETUP 80 9.1.5 EUT OPERATION CONDITIONS 80 9.1.6 TEST RESULTS 81 10 . ANTENNA CONDUCTED SPURIOUS EMISSION 85 10.1 APPLIED PROCEDURES / LIMIT 85 10.1.1 MEASUREMENT INSTRUMENTS LIST AND SETTING 85 10.1.2 TEST PROCEDURE 85 10.1.3 DEVIATION FROM STANDARD 85 10.1.4 TEST SETUP 85 10.1.5 EUT OPERATION CONDITIONS 85 Neutron Engineering Inc. Report No.: NEI-FCCP-1-1108C254 Page 5 of 99 Table of Contents Page 10.1.6 TEST RESULTS 86 11 . EUT TEST PHOTO 98 Neutron Engineering Inc. Report No.: NEI-FCCP-1-1108C254 Page 6 of 99 1. CERTIFICATION E q u i p m e n t : Cisco Edge 300 Brand Name : Cisco Model Name : CS-E300-AP-K9;HS-E300-AP-K9 A p p l i c a n t : Hon Hai Precision Ind., Co.,Ltd. F a c t o r y : HONG FU JIN PRECISION INDUSTRY (SHEN ZHEN) CO LTD Address : Bldg. D10, F21, No. 2, 2ND DONGHUAN ROAD, 10TH YOUSONG INDUSTRIAL DISTRICT,LONGHUA TOWN,BAOAN, SHENZHEN, GUANGDONG, CHINA Date of Test: Aug. 10, 2011 ~ Aug. 31, 2011 T e s t I t e m : ENGINEERING SAMPLE Standards : FCC Part15, Subpart C(15.247) / ANSI C63.4 : 2003 The above equipment has been tested and found compliance with the requirement of the relative standards by Neutron Engineering Inc. EMC Laboratory. The test data, data evaluation, and equipment configuratio…

Text truncated - open the document above for the full version.

Neutron Engineering Inc. Report No.: NEI-FCCP-1-1108C254 Page 98 of 99 11. EUT TEST PHOTO Conducted Measurement Photos Neutron Engineering Inc. Report No.: NEI-FCCP-1-1108C254 Page 98 of 99 11. EUT TEST PHOTO Conducted Measurement Photos Neutron Engineering Inc. Report No.: NEI-FCCP-1-1108C254 Page 99 of 99 Radiated Measurement Photos Neutron Engineering Inc. Report No.: NEI-FCCP-1-1108C254 Page 99 of 99 Radiated Measurement Photos