MCLJ20H076802.11abgn wireless module

1 1. Level 1 Environment‐related Substances should NEVER be used. 2. Purchase ink, paint, wire rods, and molding resins only from the business partners that Sony approves as Green Partners. 3. Recycled Resin and Coated Wire should be procured from Green Partners User Manual IEEE 802.11a/b/g/n 2x2 WiFi Module Project Name QCA9375 IEEE 802.11a/b/g/n 2x2 WiFi Module Customer Part No. 021430401 Approval Sheet Rev. 1.0 Foxconn Part No. J20H076.01 Prepared by Reviewed by Approved by Gallon G.R. Tao Robin Xu Chang‐Fu Lin HON HAI PRECISION IND. CO., LTD. No.2, 2nd Dong Huan Road, 10th YouSong lndustrial District, Longhua Town, Baoan, ShenZhen 2 CONTENTS 1. REVISION HISTORY..................................................................... 3 2 PRODUCT OVERVIEW................................................................... 4 3 SIGNAL DESCRIPTION.................................................................. 5 3.1 SIGNAL DIAGRAM........................................................................5 3.2 PINOUTS...............................................................................5 3.2.1 Connector Specification.............................................................5 3.2.2 Pin definition......................................................................5 4 ELECTRICAL SPECIFICATION............................................................ 6 4.1 ABSOLUTE MAXIMUM RATING..............................................................6 4.2 RECOMMENDED OPERATING CONDITION.....................................................6 4.3 POWER CONSUMPTION...................................................................6 4.4 POWER UP SEQUENCE...................................................................6 4.5 WLAN RF SPECIFICATIONS...............................................................7 4.5.1 WLAN RF Specification- 802.11b.....................................................7 4.5.2 WLAN RF Specification- 802.11g.....................................................8 4.5.3 WLAN RF Specification- 802.11n (2.4GHz) HT20.......................................9 4.5.4 WLAN RF Specification- 802.11a....................................................10 4.5.5 WLAN RF Specification- 802.11n (5GHz) HT20.......................................11 4.5.6 WLAN RF Specification- 802.11n (5GHz) HT40.......................................12 5 SCHEMATIC AND PCB LAYOUT......................................................... 13 5.1 MODULE SCHEMATIC....................................................................13 5.2 MODULE PCB LAYOUT..................................................................15 5.2.1 PCB Stack-up....................................................................15 5.2.2 Component Placement.............................................................15 5.2.3 PCB Layout......................................................................16 6 ANTENNA SPECIFICATIONS............................................................ 18 6.1 PCB PRINTED ANTENNA PATTERN.........................................................18 6.2 ANTENNA RADIATION PERFORMANCE.......................................................18 7 MODULE MECHANICAL SPECIFICATIONS............................................... 21 8 HANDLING NOTICE.................................................................... 22 9 RELIABILITY TEST PLAN...............................................................23 10 MARKING INFORMATION...............................................................25 11 PACKING INFORMATION...............................................................26 3 1. Revision History Date Document revision Change History 2013/5/24 1.0 Initial release ! 5! 2 Product Overview This documentation outlines the QCA9375 WiFi Module. It is 802.11a/b/g/n compatible, ARIB STD-T66 Compatible; the module Host I/F is USB 2.0. IEEE 802.11 a/b/g and 802.11n payload data rates for Wireless Local Area Network (WLAN). 1.1 Operating Frequency: 2402~2483.5MHz, 5150MHz~5250MHz, 5250MHz~5350MHz, 5470MHz~5725MHz, 5725MHz~5845MHz 1.2 Modulation: DBPSK, DQPSK, CCK, BPSK, QPSK, 16QAM, 64QAM 1.3 Data Rates: 1/2/5.5/11Mbps (11b) 6/9/12/18/24/36/48/54 Mbps (11g) MCS0~MCS15 1.4 Security: it supports WEP, TKIP, AES, WPA/WPA2 and WAPI 1.5 Full 802.11e QoS support including WMM. 1.6 Support Short Guard interval and Frame aggregation with A-MPDU The module is designed with a WTB (Wire to Board) connector to connect to host. Dimension is 40.0mm x37.5mm x 5.45mm (typical). Below figure1 shows functional block diagram of the WLAN module. Figure 1: Module Functional Block Diagram ! 6! 3 Signal Description 3.1 Signal Diagram Below figure 2 shows its signal diagram. Figure 2: Module Signal Diagram 3.2 Pinouts 3.2.1 Connector Specification JST WTB connector, Part Number: SM10B-GHS-TB(LF) ! 3.2.2 Pin definition Pin# Pin Name Pin Type Description Remark 1 GND - Ground 2 WoW O Wake-up on wireless LAN Active high 3 CHIP_PWD_L I Reset to module Active low 4 GND - Ground 5 USB_DM I/O USB differential signal negative 6 USB_DP I/O USB differential signal positive 7 VCC_3.3V Power 3.3V power supply +/-5% 8 VCC_3.3V Power 3.3V power supply +/-5% 9 GND - Ground 10 GND - Ground Pin1 6 4 Electrical Specification 4.1 Absolute Maximum Rating Symbol Condition Min. Typ. Max Unit VCC_3.3V Respect to GND -0.3 3.3 3.6 V CHIP_PWD_L Respect to GND -0.3 3.3 3.6 V Max Ripple on Supplied Voltage 3.3V 165 mVpp Operating Temperature -- -10 25 75 °C Storage Temperature -- -40 25 85 °C 4.2 Recommended Operating Condition Symbol Condition Min. Typ. Max Unit VCC_3.3V Respect to GND 3.14 3.3 3.46 V CHIP_PWD_L Respect to GND -0.3 3.3 3.46 V 4.3 Power Consumption Symbol Condition Min Typ. Max Unit Supply voltage 3.0 3.3 3.6 V Tx Current(1Mbps/16dBm,MIMO) -- 465 -- mA Tx Current(11g: 54Mbps/14.5dBm,MIMO) -- 400 -- mA Tx Current(11gn: MCS15/13dBm/HT20,MIMO) -- 380 -- mA Tx Current(11a: 6Mbps/15dBm,MIMO) -- 630 -- mA Tx Current(11a: 54Mbps/12dBm,MIMO) -- 490 -- mA Tx Curren…

Text truncated - open the document above for the full version.

HON HAI PRECISION IND. CO., LTD. 5F-1,5 Hsin-An Road Hsinchu, Science-Based Industrial Park Taiwan, R.O.C. Date: 2013/5/27 GENERAL DECLARATION We, HON HAI PRECISION IND. CO., LTD. declare that the device does not support any non-US channels in all the operational mode(s) for the following product. FCC ID: MCLJ20H076 If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you! Signature: Rio Chen Compliance Manager HON HAI PRECISION IND. CO., LTD. TEL: +886-3-5784975 FAX: +886-3-5775100 E-mail: [email protected]

HON HAI PRECISION IND. CO., LTD. 5F-1,5 Hsin-An Road Hsinchu, Science-Based Industrial Park Taiwan, R.O.C. Declaration for DFS client devices Date: 2013/7/23 FCC ID: MCLJ20H076 IC: 2878D-J20H076 Dear Examiner: Per KDB# 848637, We, Hon Hai PRECISION IND.CO.,LTD declare that following description truly represent our product in consideration. Please do not hesitate to contact us, if further info is required. Thanks. a). A channel/frequency plan for the device showing the channels that have active scanning or passive scanning. Active scanning is where the device can transmit a probe (beacon) and passive scanning is where the device can listen only without probes. Below is the channel / frequency plan for the device b). For client devices that have software configuration control to operate in different modes (active scanning in some and passive scanning in others) or in different bands (devices with multiple equipment classes or those that operate on non-DFS frequencies), or modular devices that configure the modes of operations through software; the applicant must provide in the application software and operations description that discuss how the software and / or hardware is implemented to ensure that proper operations modes cannot be modified by an end user or an installer. Also, include an attestation that the device complies with the requirements for software configuration control as discussed in KDB #594280. CH 1 2 3 4 5 6 7 8 9 10 11 Frequency (MHz) 2412 2417 2422 2427243224372442 2447 2452 2457 2462 Scan Type Active Active Active Active Active Active Active Active Active Active Active CH 36 40 44 48 52 56 60 64 Frequency (MHz) 5180 5200 5220 5240526052805300 5320 Scan Type Active Active Active Active Passive Passive Passive Passive CH 100 104 108 112 116 132 136 140 Frequency (MHz) 5500 5520 5540 5560558056605680 5700 Scan Type Passive Passive Passive Passive Passive Passive Passive Passive CH 149 153 157 161 165 Frequency (MHz) 5745 5765 5785 58055825 Scan Type Active Active Active Active Active On DFS channels, the WLAN driver on the device operates under the control of an AP at all times, except when in ad-hoc mode, on US non-DFS channels. As described in the answer to question a, the device passively scans DFS frequencies until a master device is detected. The control of this functionality is not accessible to anyone under any conditions. Furthermore, the firmware is locked by proprietary password and cannot be changed or modified by end user. If you should have any question(s) regarding this declaration, please don’t hesitate to contact us. Thank you! Signature: Rio Chen Compliance Manager HON HAI PRECISION IND. CO., LTD. TEL: +886-3-5784975 FAX: +886-3-5775100 E-mail: [email protected]

HON HAI PRECISION IND. CO., LTD. 5F-1,5 Hsin-An Road Hsinchu, Science-Based Industrial Park Taiwan, R.O.C. Federal Communications Commission Authorization and Evaluation Division Date: July 15, 2013 Confidentiality Request FCC ID: MCLJ20H076 Pursuant to DA 04-1705 of the Commission’s Rules, we request short-term confidential treatment for the following information until Oct. 15th, 2013 of Equipment Authorization in order to ensure sensitive business information remains confidential until the actual marketing of the device: External Photos Test Setup Photos User’s Manual Internal Photo Thank you! Sincerely yours, ------------------------------------------------------- Rio Chen Compliance Manager HON HAI PRECISION IND. CO., LTD. TEL: +886-3-5784975 FAX: +886-3-5775100 E-mail: [email protected]

HON HAI PRECISION IND. CO., LTD. 5F-1,5 Hsin-An Road Hsinchu, Science-Based Industrial Park Taiwan, R.O.C. Date:2013/5/27 FCC ID: MCLJ20H076 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, Rio Chen Compliance Manager HON HAI PRECISION IND. CO., LTD. TEL: +886-3-5784975 FAX: +886-3-5775100 E-mail: [email protected]

HON HAI PRECISION IND. CO., LTD. 5F-1,5 Hsin-An Road Hsinchu, Science-Based Industrial Park Taiwan, R.O.C. AGENCY AUTHORIZATION LETTER Date: 2013/5/27 To whom it may concern: We, the undersigned, , HON HAI PRECISION IND. CO., LTD. hereby authorize Bureau Veritas Consumer Products Services (H.K) Ltd., Taoyuan Branch. of Taiwan to act on our behalf in all matters relating to all processes required in the FCC Part 15C+15E approval and any communication needed with the national authority. Any and all acts carried out by Bureau Veritas Consumer Products Services (H.K) Ltd., Taoyuan Branch. on our behalf shall have the same effects as acts of our own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you! Sincerely yours, Signature: Rio Chen Compliance Manager HON HAI PRECISION IND. CO., LTD. TEL: +886-3-5784975 FAX: +886-3-5775100 E-mail: [email protected]

FCC ID: MCLJ20H076 Report No.: RF130523E10 Modular Approval Request Letter Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch July 16, 2013 Dear Application Examiner, HON HAI Precision Ind. Co., Ltd., device: a 802.11abgn wireless module, FCC ID: MCLJ20H076 would like to have your authorization as a modular device. The requirements of section 15.212 of FCC rules have been met and shown on the following statements. 1. “The modular transmitter must have its own RF shielding.”: The radio portion of this module has been shielded, please see exhibition External Photo. 2. “The modular transmitter must have buffered modulation/data inputs.” The EUT has buffered data input. It is integrated in chip QCA9375. 3. “The modular transmitter must have its own power supply regulation.” The part number of this regulator is QCA9375. 4. “The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(C).” The EUT meets the FCC antenna requirements. The spurious emission, unique antenna connector and photo of antennas are shown in the test report. 5. “The modular transmitter must be tested in a stand-alone configuration” The EUT was tested in a stand-alone configuration via extender. Please see section Photographs of Test Configuration in the test report, the EUT was plugged in this extender. 6. “The modular transmitter must be labeled with its own FCC ID number.” Please see exhibition Label Sample for the FCC ID of this module. And also in the exhibition Users Manual, there are instructions give to the OEM on how to label the end product. 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.” The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are given in the Users Manual. 8. “The modular transmitter must comply with any applicable RF exposure requirements.” The EUT is compliant with all applicable RF exposure requirements. RF Exposure is addressed in the RF exposure exhibition. Please contact me if you have any further questions. Thanks for your attention. Best Regards, signature Hank Chung Assistant Manager Bureau Veritas Consumer Products Services (H.K.) Ltd., Hsinchu Branch

Report No.: 130523E10 1 of 5 CONSTRUCTION PHOTOS OF EUT Report No.: 130523E10 4 of 5

003-130120 FCC ID:MCLJ20H076 IC:2878D-J20H076 (Fig. 1) FCC ID: MCLJ20H076 FCC LABEL LOCATION The label will be permanently affixed at a conspicuous location on the device. Label

Report No.: 130523E10 2 of 5 Report No.: 130523E10 3 of 5 Report No.: 130523E10 5 of 5

FCC ID: MCLJ20H076 Report No.: RF130523E10 Operational Description This device is a 802.11abgn wireless module, which operates in both of the 5GHz and 2.4GHz bands and can transmitting simultaneously, the maximum data rate could be up to 300Mbps which OFDM technique. If the signal to noise radio is too poor which could not support 300Mbps, the 11Mbps data rate with DSSS technique will be applied. The transmitter of the EUT is powered from DC 3.3V ± 10% from host equipment. The antennas provided to the EUT, please refer to the following table: The other instruction, please have a look at the users manual. FCC 15.407(c) states: The device shall automatically discontinue transmission in case of either absence of information to transmit or operational failure. These provisions are not intended to preclude the transmission of control or signaling information or the use of repetitive codes used by certain digital technologies to complete frame or burst intervals. Applicants shall include in their application for equipment authorization a description of how this requirement is met” Data transmission is always initiated by software, which is then pass down through the MAC, through the digital and analog baseband, and finally to the RF chip. Several special packets (ACKs, CTS, PSPoll, etc...) are initiated by the MAC. There are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only while one of the aforementioned packets are being transmitted.

Report No.: SA130523E10 1 of 6 Report Format Version 5.0.0 RF EXPOSURE REPORT REPORT NO.: SA130523E10 MODEL NO.: J20H076 FCC ID: MCLJ20H076 RECEIVED: May 23, 2013 TESTED: May 30, 2013 ISSUED: July 15, 2013 APPLICANT: Hon Hai PRECISION IND.CO.,LTD ADDRESS: 5F-1, Hsin-An Road, Hsinchu, Science Industrial Park, Taiwan, R.O.C. ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS: No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. This report should not be used by the client to claim product certification, approval, or endorsement by any government agencies. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification Report No.: SA130523E10 2 of 6 Report Format Version 5.0.0 TABLE OF CONTENTS RELEASE CONTROL RECORD ..................................................................................... 3 1. CERTIFICATION ...................................................................................................... 4 2. RF EXPOSURE LIMIT .............................................................................................. 5 3. MPE CALCULATION FORMULA ............................................................................. 5 4. CLASSIFICATION .................................................................................................... 5 5. CALCULATION RESULT OF MAXIMUM CONDUCTED POWER ........................... 6 Report No.: SA130523E10 3 of 6 Report Format Version 5.0.0 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA130523E10 Original release July 15, 2013 Report No.: SA130523E10 4 of 6 Report Format Version 5.0.0 1. CERTIFICATION PRODUCT: 802.11abgn wireless module BRAND NAME: FOXCONN MODEL NO.: J20H076 TEST SAMPLE: ENGINEERING SAMPLE APPLICANT: Hon Hai PRECISION IND.CO.,LTD TESTED DATE: May 30, 2013 STANDARDS: FCC Part 2 (Section 2.1091) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 The above equipment (Model: J20H076) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE: Jan. 09, 2013 ( Lori Chung, Specialist ) APPROVED BY : , DATE: Jan. 09, 2013 ( May Chen, Manager ) Report No.: SA130523E10 5 of 6 Report Format Version 5.0.0 2. RF EXPOSURE LIMIT LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY (mW/cm 2 ) AVERAGE TIME (minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 3. MPE CALCULATION FORMULA Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale pi = 3.1416 r = distance between observation point and center of the radiator in cm 4. CLASSIFICATION The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. Report No.: SA130523E10 6 of 6 Report Format Version 5.0.0 5. CALCULATION RESULT OF MAXIMUM CONDUCTED POWER For 15.247(2.4GHz): FREQUENCY BAND (MHz) MAX POWER (mW) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/ cm 2 ) LIMIT (mW/cm 2 ) 2412-2462 657.863 3.18 20 0.27219 1 For 15.247(5GHz): FREQUENCY BAND (MHz) MAX POWER (mW) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/ cm 2 ) LIMIT (mW/cm 2 ) 5745 ~ 5825 363.291 4.98 20 0.22750 1 For 15.407(5GHz): FREQUENCY BAND (MHz) MAX POWER (mW) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/ cm 2 ) LIMIT (mW/cm 2 ) 5180-5240 5260-5320 5500-5580 & 5660-5700 235.624 4.78 20 0.14091 1 --- END ---

Report No.: RF130523E10 1 of 92 Report Format Version 5.2.0 Reference No.:121122E01 FCC TEST REPORT (15.247) REPORT NO.: RF130523E10 MODEL NO.: J20H076 FCC ID: MCLJ20H076 RECEIVED: May 23, 2013 TESTED: May 29 to June 05, 2013 ISSUED: July 15, 2013 APPLICANT: Hon Hai PRECISION IND.CO.,LTD ADDRESS: 5F-1, Hsin-An Road, Hsinchu, Science Industrial Park, Taiwan, R.O.C. ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS : No. 81-1, Lu Liao Keng, 9th Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (1): No. 81-1, Lu Liao Keng, 9th Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification Report No.: RF130523E10 2 of 92 Report Format Version 5.2.0 Reference No.:121122E01 Table of Contents RELEASE CONTROL RECORD ........................................................................................ 6 1. CERTIFICATION .................................................................................................... 7 2. SUMMARY OF TEST RESULTS ............................................................................ 8 2.1 MEASUREMENT UNCERTAINTY .......................................................................... 9 3. GENERAL INFORMATION ................................................................................... 10 3.1 GENERAL DESCRIPTION OF EUT ..................................................................... 10 3.2 DESCRIPTION OF TEST MODES ....................................................................... 12 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ........................ 13 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS ....................................... 16 3.4 DESCRIPTION OF SUPPORT UNITS .................................................................. 17 3.5 CONFIGURATION OF SYSTEM UNDER TEST ................................................... 17 4. TEST TYPES AND RESULTS (FOR 2.4GHZ, 2400 ~ 2483.5MHZ BAND) ........... 18 4.1 CONDUCTED EMISSION MEASUREMENT ........................................................ 18 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ...................................... 18 4.1.2 TEST INSTRUMENTS .......................................................................................... 18 4.1.3 TEST PROCEDURES .......................................................................................... 19 4.1.4 DEVIATION FROM TEST STANDARD ................................................................. 19 4.1.5 TEST SETUP ....................................................................................................... 20 4.1.6 EUT OPERATING CONDITIONS ......................................................................... 20 4.1.7 TEST RESULTS ................................................................................................... 21 4.2 RADIATED EMISSION AND BANDEDGE MEASUREMENT ................................ 23 4.2.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT .............. 23 4.2.2 TEST INSTRUMENTS .......................................................................................... 24 4.2.3 TEST PROCEDURES .......................................................................................... 26 4.2.4 DEVIATION FROM TEST STANDARD ................................................................. 26 4.2.5 TEST SETUP ....................................................................................................... 27 4.2.6 EUT OPERATING CONDITIONS ......................................................................... 27 4.2.7 TEST RESULTS ................................................................................................... 28 4.3 6DB BANDWIDTH MEASUREMENT ................................................................... 38 4.3.1 LIMITS OF 6DB BANDWIDTH MEASUREMENT ................................................. 38 4.3.2 TEST INSTRUMENTS .......................................................................................... 38 4.3.3 TEST PROCEDURE ............................................................................................. 38 4.3.4 DEVIATION FROM TEST STANDARD ................................................................. 38 4.3.5 TEST SETUP ....................................................................................................... 38 4.3.6 EUT OPERATING CONDITIONS ............................................…

Text truncated - open the document above for the full version.

Report No.: RF130523E10-1 1 of 77 Report Format Version 5.2.0 Reference No.:121122E01 FCC TEST REPORT (15.407) REPORT NO.: RF130523E10-1 MODEL NO.: J20H076 FCC ID: MCLJ20H076 RECEIVED: May 23, 2013 TESTED: May 29 to June 05, 2013 ISSUED: July 15, 2013 APPLICANT: Hon Hai PRECISION IND.CO.,LTD ADDRESS: 5F-1, Hsin-An Road, Hsinchu, Science Industrial Park, Taiwan, R.O.C. ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS : No. 81-1, Lu Liao Keng, 9th Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (1): No. 81-1, Lu Liao Keng, 9th Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. TEST LOCATION (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan, R.O.C. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification Report No.: RF130523E10-1 2 of 77 Report Format Version 5.2.0 Reference No.:121122E01 Table of Contents RELEASE CONTROL RECORD..............................................................................4 1. CERTIFICATION ..................................…

Text truncated - open the document above for the full version.