MCLT77H330WiFi Module

Confidential 1 T77H330 WiFi Module User Manual Rev. 0.01 Confidential 2 1. Introduction Project Name: 802.11n WiFi Module This documentation describes the product specification of the WiFi 802.11b/g/n module, it is a confidential document of FOXCONN. 1.1 Scope The T77H330 802.11b/g/n module provides wireless modem functionality utilizing CCK and OFDM technology. The objective of this use manual is to verify the functionality of the T77H330 802.11b/g/n module RF/Digital electronic design against the design specifications. 1.2 Function ¾ Support IEEE 802.11b/g/n specified functions ¾ 1x1 single stream with antenna diversity ¾ USB2.0 interface support Confidential 3 2. Product Specification 2.1 RF Specification For 802.11b RF Specifications: Confidential 4 For 802.11g RF Specifications: For 802.11n HT20 RF Specifications: Confidential 5 For 802.11n HT20 RF Specifications: Confidential 6 Confidential 7 2.2 Electrical Specification Absolute Maximum Ratings These specifications indicate levels where permanent damage to the device can occur. Functional operation is not guaranteed under these conditions. Operation at absolute maximum conditions for extended can adversely affect long-term reliability of the device. DC Specification Confidential 8 3. Pin descriptions 3.1 USB Pin descriptions 3.2 RF Connector Confidential 9 4. Mechanical Drawing Confidential 10 FCC Notice: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Confidential 11 This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: MCLT77H330”. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Canada Notice This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable. Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Déclaration d'exposition aux radiations: Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement do…

Text truncated - open the document above for the full version.

HON HAI PRECISION IND. CO., LTD. 5F-1,5 Hsin-An Road Hsinchu, Science-Based Industrial Park Taiwan, R.O.C. Date: 2011/9/20 G E N E R A L D E C L A R A T I O N We, HON HAI PRECISION IND. CO., LTD. declares that device does not have “Ad Hoc on non-US frequencies” while applying for the follow product. FCC ID: MCLT77H330 If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you! Signature: Rio Chen Compliance Manager HON HAI PRECISION IND. CO., LTD. TEL: +886-3-5784975 FAX: +886-3-5775100 E-mail: [email protected]

HON HAI PRECISION IND. CO., LTD. 5F-1,5 Hsin-An Road Hsinchu, Science-Based Industrial Park Taiwan, R.O.C. Date:2011/9/20 FCC ID: MCLT77H330 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours, Rio Chen Compliance Manager HON HAI PRECISION IND. CO., LTD. TEL: +886-3-5784975 FAX: +886-3-5775100 E-mail: [email protected]

HON HAI PRECISION IND. CO., LTD. 5F-1,5 Hsin-An Road Hsinchu, Science-Based Industrial Park Taiwan, R.O.C. Federal Communications Commission Authorization and Evaluation Division Date: September 20, 2011 Confidentiality Request FCC ID: MCLT77H330 Pursuant to DA 04-1705 of the Commission’s Rules, we request short-term confidential treatment for the following information until April. 10, 2010 of Equipment Authorization in order to ensure sensitive business information remains confidential until the actual marketing of the device: External Photos Test Setup Photos User’s Manual Internal Photo Thank you! Sincerely yours, ------------------------------------------------------- Rio Chen Compliance Manager HON HAI PRECISION IND. CO., LTD. TEL: +886-3-5784975 FAX: +886-3-5775100 E-mail: [email protected]

HON HAI PRECISION IND. CO., LTD. 5F-1,5 Hsin-An Road Hsinchu, Science-Based Industrial Park Taiwan, R.O.C. AGENCY AUTHORIZATION LETTER Date: 2011/9/20 To whom it may concern: We, the undersigned, , HON HAI PRECISION IND. CO., LTD. hereby authorize Bureau Veritas Consumer Products Services (H.K) Ltd., Taoyuan Branch. of Taiwan to act on our behalf in all matters relating to all processes required in the FCC Part 15C approval and any communication needed with the national authority. Any and all acts carried out by Bureau Veritas Consumer Products Services (H.K) Ltd., Taoyuan Branch. on our behalf shall have the same effects as acts of our own. If you have any questions regarding the authorization, please don’t hesitate to contact us. Thank you! Sincerely yours, Signature: Rio Chen Compliance Manager HON HAI PRECISION IND. CO., LTD. TEL: +886-3-5784975 FAX: +886-3-5775100 E-mail: [email protected]

FCC ID: MCLT77H330 Report No.: RF110909E05 Modular Approval Request Letter Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch October 3, 2011 Dear Application Examiner, HON HAI Precision Ind. Co., Ltd., device: a WLAN module, FCC ID: MCLT77H330, would like to have your authorization as a modular device. The requirements of section 15.212 of FCC rules have been met and shown on the following statements. 1. “The modular transmitter must have its own RF shielding.”: The radio portion of this module has been shielded, please see exhibition External Photo. 2. “The modular transmitter must have buffered modulation/data inputs.” The EUT has buffered data inputs, it is integrated in chip RT5370. 3. “The modular transmitter must have its own power supply regulation.” The part number of this regulator is AT25640B/NI. 4. “The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(C).” The EUT meets the FCC antenna requirements. The spurious emission, unique antenna connector and photo of antennas are shown in the test report. 5. “The modular transmitter must be tested in a stand-alone configuration” The EUT was tested in a stand-alone configuration via extender. Please see section Photographs of Test Configuration in the test report, the EUT was plugged in this extender. 6. “The modular transmitter must be labeled with its own FCC ID number.” Please see exhibition Label Sample for the FCC ID of this module. And also in the exhibition Users Manual, there are instructions give to the OEM on how to label the end product. FCC ID: MCLT77H330 Report No.: RF110909E05 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.” The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are given in the Users Manual. 8. “The modular transmitter must comply with any applicable RF exposure requirements.” The EUT is compliant with all applicable RF exposure requirements. RF Exposure is addressed in the RF exposure exhibition. Please contact me if you have any further questions. Thanks for your attention. Best Regards, signature Hank Chung Assistant Manager Bureau Veritas Consumer Products Services (H.K.) Ltd., Hsinchu Branch

Page 1 CONSTRUCTION PHOTOS OF EUT Model No.: T77H330

11.08.09 Annie Huang 11.08.11 Annie Huang 1 update label content 11.08.13 Annie Huang 2 update label content 11.08.15 Annie Huang 3 modify 11.08.18 Annie Huang 4 Modify label size and update label content 11.09.03 Annie Huang 5 remove ANATEL NO and update label layout label size Annie Huang Sunny w u PTT label 50# mylar 500.XXXXX.005 Note:1. Surface material: 50#Mylar thickness: 0.05+/-0.005mm color: matte white 2. Adhesive: Acrylic thickness: 0.023+/-0.002mm 3. Liner: Glassine 4.All of the font:Arial 5.Printing color:black 6.Font type:Arial. Font height:1.2mm label stick position: picture just for reference WiFi module PTT label Scale: 1:1 XXXXXXXXXXXX FCC ID:XXXXXXXXX IC:XXXXXXXXXX MadeinChina Model No. : T77H330 WiFi Module IC:XXXXXXXXXX MadeinChina ANATEL NO. : XXXXX Model No. : T77H330 WiFi Module Scale: 2:1 XXXXXXXXXXXX FCC ID:XXXXXXXXX IC:XXXXXXXXXX MadeinChina Model No. : T77H330 WiFi Module T

(Fig. 1) FCC ID: MCLT77H330 FCC LABEL LOCATION The label will be permanently affixed at a conspicuous location on the device. Label

Page 2

FCC ID: MCLT77H330 Report No.: RF110909E05 Operational Description This device is a WLAN Module, which operates in the 2.4GHz frequency spectrum with throughput of up to150Mbps which OFDM technique will be applied. If the signal to noise radio is too poor which could not support 150Mbps, the 11Mbps data rate with DSSS technique will be applied. The transmitter of the EUT is powered by 5Vdc from host equipment. The antenna is PCB Printed antenna with Switching Type RF antenna connectors. The other instruction, please have a look at the users manual.

Report No.: SA110909E05 Report Format Version 4.0.0. 1 RF EXPOSURE REPORT REPORT NO.: SA110909E05 MODEL NO.: T77H330 FCC ID: MCLT77H330 RECEIVED: Sep. 09, 2011 TESTED: Sep. 16, 2011 ISSUED: Sep. 30, 2011 APPLICANT: Hon Hai PRECISION IND.CO.,LTD ADDRESS: 5F-1,5 Hsin-An Road Hsinchu, Science-Based Industrial Park Taiwan, R.O.C. ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS: No. 81-1, Lu Liao Keng, 9th Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan This test report consists of 6 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced, except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval or endorsement by any government agency. The test results in the report only apply to the tested sample. Report No.: SA110909E05 Report Format Version 4.0.0. 2 TABLE OF CONTENTS RELEASE CONTROL RECORD....................................................................................3 1. CERTIFICATION.......................................................................................4 2. RF EXPOSURE LIMIT..............................................................................5 3. MPE CALCULATION FORMULA..............................................................5 4. CLASSIFICATION.....................................................................................5 5. CALCULATION RESULT OF MAXIMUM CONDUCTED POWER...........6 Report No.: SA110909E05 Report Format Version 4.0.0. 3 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA110909E05 Original release Sep. 30, 2011 Report No.: SA110909E05 Report Format Version 4.0.0. 4 1.CERTIFICATION PRODUCT: WiFi Module BRAND NAME: FOXCONN MODEL NO.: T77H330 TEST SAMPLE: ENGINEERING SAMPLE APPLICANT: Hon Hai PRECISION IND.CO.,LTD STANDARDS: FCC Part 2 (Section 2.1091) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 The above equipment (Model: T77H330) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE: June 20, 2011 ( Midoli Peng, Specialist) APPROVED BY : , DATE: June 20, 2011 ( May Chen, Deputy Manager ) Report No.: SA110909E05 Report Format Version 4.0.0. 5 2.RF Exposure Limit LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY (mW/cm 2 ) AVERAGE TIME (minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 3.MPE calculation Formula Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm 4.Classification The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. Report No.: SA110909E05 Report Format Version 4.0.0. 6 5.Calculation result of maximum conducted power For WLAN: 15.247(2.4GHz) FREQUENCY BAND (MHz) CONDUCTED POWER (mW) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/ cm 2 ) LIMIT (mW/cm 2 ) 2412-2462 354.8 1.29 20 0.095 1.00 ---END---

Report No.: RF110909E05 R1 1 Report Format Version 4.0.0 Cancels and replaces the report No.: RF110909E05 dated Sep. 30, 2011 FCC TEST REPORT REPORT NO.: RF110909E05 R1 MODEL NO.: T77H330 FCC ID: MCLT77H330 RECEIVED: Sep. 09, 2011 TESTED: Sep. 15 to 16, 2011 ISSUED: Oct. 04, 2011 APPLICANT: Hon Hai PRECISION IND.CO.,LTD ADDRESS: 5F-1,5 Hsin-An Road Hsinchu, Science-Based Industrial Park Taiwan, R.O.C. ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS : No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan TEST LOCATION (1): No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan TEST LOCATION (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan This test report consists of 80 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval, or endorsement by TAF or any government agencies. The test results in the report only apply to the tested sample. Report No.: RF110909E05 R1 2 Report Format Version 4.0.0 Cancels and replaces the report No.: RF110909E05 dated Sep. 30, 2011 Table of Contents RELEASE CONTROL RECORD........................................................................................4 1. CERTIFICATION....................................................................................................5 2. SUMMARY OF TEST RESULTS............................................................................6 2.1 MEASUREMENT UNCERTAINTY..........................................................................7 3. GENERAL INFORMATION.....................................................................................8 3.1 GENERAL DESCRIPTION OF EUT.......................................................................8 3.2 DESCRIPTION OF TEST MODES.......................................................................10 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL........................11 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS.......................................14 3.4 DESCRIPTION OF SUPPORT UNITS..................................................................15 3.5 CONFIGURATION OF SYSTEM UNDER TEST...................................................16 4. TEST TYPES AND RESULTS..............................................................................17 4.1 CONDUCTED EMISSION MEASUREMENT........................................................17 4.1.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT......................................17 4.1.2 TEST INSTRUMENTS..........................................................................................17 4.1.3 TEST PROCEDURES..........................................................................................18 4.1.4 DEVIATION FROM TEST STANDARD.................................................................18 4.1.5 TEST SETUP.......................................................................................................19 4.1.6 EUT OPERATING CONDITIONS.........................................................................19 4.1.7 TEST RESULTS...................................................................................................20 4.2 RADIATED EMISSION MEASUREMENT.............................................................22 4.2.1 LIMITS OF RADIATED EMISSION MEASUREMENT...........................................22 4.2.2 TEST INSTRUMENTS..........................................................................................23 4.2.3 TEST PROCEDURES..........................................................................................24 4.2.4 DEVIATION FROM TEST STANDARD.................................................................24 4.2.5 TEST SETUP.......................................................................................................25 4.2.6 EUT OPERATING CONDITIONS.........................................................................25 4.2.7 TEST RESULTS...................................................................................................26 4.3 6dB BANDWIDTH MEASUREMENT....................................................................55 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT..................................................55 4.3.2 TEST INSTRUMENTS..........................................................................................55 4.3.3 TEST PROCEDURE.............................................................................................55 4.3.4 DEVIATION FROM TEST STANDARD.................................................................55 4.3.5 TEST SETUP.......................................................................................................55 4.3.6 EUT OPERATING CONDITIONS.........................................................................55 4.3.7 TEST RESULTS...................................................................................................56 4.4 MAXIMUM PEAK OUTPUT POWER....................................................................60 4.4.1 LIMITS OF MAXIMUM PEAK OUTPUT POWER MEASUREMENT.....................60 4.4.2 INSTRUMENTS....................................................................................................60 Report No.: RF110909E05 R1 3 Report Format Version 4.0.0 Cancels and replaces the report No.: RF110909E05 dated Sep. 30, 2011 4.4.3 TEST PROCEDURES..........................................................................................60 4.4.4 DEVIATION FROM TEST STANDARD.................................................................60 4.4.5 TEST SETUP.......................................................................................................60 4.4.6 EUT OPERATING CONDITIONS.…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST 2 RADIATED EMISSION TEST (BELOW 1GHz) 3 RADIATED EMISSION TEST (ABOVE 1GHz)