MCLT77Z29500PCI-E Embedded Module

TANGO module HW installation guide : 1. You must turn off USB5V via the switch(ie.SW200) and connect 2 USB cables to USB ports(i.e J300/J204) of the computer before putting TANGO module into the test fixture 2. Plug in TANGO module into the test fixture from right side and use clapper on the test fixuter to fix the TANGO. 3. Put SIM card into SIM card socket correctly. 4. Select adequate RF adaptors to connect RF connector in order to do electric measurement. Then turn on USB5V via the switch Note : below is the placement of each component TANGO module driver user guide : 1. First have HostDrivers (NVIDIA_TANGO_5.45.0455_Release) into your computer. The contents are listed as below : 2. Then click the file name (NVIDIA_TANGO_5.45.0455_Release) to follow its instructions to install until you complete the driver’s installation. 3. Put TANGO module into the socket, take out 2 mini‐USB cables to plug in 4. Turn on the switch to let USB 5V input into the fixture. Turn off the module if the switch shift toward down. 5. The device management shows 4 unknown COM ports when the switch turn on. You have to follow the indication of the pop‐up window to install adequate drivers. 5‐1 Please choose the right directory with the TANGO driver for diagnostic port 5‐2 You can see diagnostic port once you correctly installed. 5‐3 Next driver to be installed is network port. You follow same way to install the driver. 5‐4 The third driver to be installed is modem port. You follow same way to install the driver. 5‐5 The fourth driver to be installed is AT port. You follow same way to install the driver. In conclusion, you can see diagnostic , network , modem , and AT ports in the device management once you succeed.

HON HAI Precision IND. CO., LTD. 5F-1,5 Hsin-An Road Hsinchu, Science-Based Industrial Park Taiwan, R.O.C TEL: +886-2-22675511 FAX:+886-2-22676517 Attestation for FCC Declaration of Conformity Model Numb er: TangoP1001 Date: 2 012/8/20 FCC ID: MCLT77Z29500 Please be notified that we, HON HAI Precision IND. CO., LTD. declares that the product which bears the above FCC ID is also compliant with the FCC requirements for DoC. The test report numbers supporting the DoC is 1207FE26. Testing in regards to this report was done by A Test Lab Techno Corp., located in No.140-1 Changan Str., Bade City Taoyuan County Taiwan, which has been accredited in accordance to all of the requirements of 47 CFR 2.948 (d) and (e) of the FCC rules and KDB349827. Sincerely, HON HAI Precision IND. CO., LTD. Mrs. Rio Chen

HON HAI Precision IND. CO., LTD. Date: 2012/8/20 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 c.c. SIEMIC, INC. 2206 Ringwood Avenue, San Jose, CA 95131 USA To whom it may concern: I, the undersigned, hereby authorize Murphy Wang, Director of A Test Lab Techno Corp. and hereafter referred to as ATL, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Murphy Wang, Director of A Test Lab Techno Corp. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing ATL as our agent, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i) keep a record of all complaints made known to the us relating to the product’s compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested; j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Compliance Manger / Mrs. Rio Chen HON HAI Precision IND. CO., LTD. REMARK: 1. This authorization letter will be sent along with your application when filing with the Certification Division. 2. Please follow the format and type it on company letterhead and send original to us. 3. Authorized signature must be in agreement with grantee code contact in FCC database.

SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 1 Rev 3.0 HON HAI Precision IND. CO., LTD. 2012/8/23 To: SIEMIC, INC. 775 Montague Expressway, Milpitas, CA 95035 USA Dear Sir/Madam, Re: Project and Product Certification Representative Authorization Letter We, HON HAI Precision IND. CO., LTD. hereby authorize SIEMIC, INC. to act as a Certification Body for certifying for the following project(s): PCI-E Embedded Module, TANGOP1001 We affirm that between SIEMIC and HON HAI Precision IND. CO., LTD., any difference in understanding, including test plan, measurement methods, applicable standards and relevant procedures and processes have been resolved prior to commencement of testing activities. Sincerely, Mrs. Rio Chen / Compliance manger HON HAI Precision IND. CO., LTD. 5F-1, 5 Hsin-An Road Hsinchu, Science-Based Industrial Park Taiwan, R.O.C

HON HAI Precision IND. CO., LTD. Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC ID: MCLT77Z29500 To Whom It May Concern: Pursuant to the provisions of Sections 0.457 and 0.459 of the Commission’s rules (47 CFR §§ 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Operation Description Parts List Tune-Up Procedure Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachments for 180 days since the date we get Certification. External Photos Internal Photos Test Setup Photos User Manual It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards Mrs. Rio Chen Compliance manger HON HAI Precision IND. CO., LTD. 2012/8/20

HON HAI Precision IND. CO., LTD. 5F-1,5 Hsin-An Road Hsinchu, Science-Based Industrial Park Taiwan, R.O.C Tel: +886-3-5784975 Subject: Module Approval Date: 8/23/2012 FCC ID: MCLT77Z29500 Regarding to the FCC 15.212, HON HAI Precision IND. CO., LTD. would like to request modular approval for the submission FCC ID. HON HAI Precision IND. CO., LTD. confirms that the product complies with numbered requirements identified below: 1. The modular transmitter has its own RF shielding. (Please review external photos). 2. The modular transmitter have buffered modulation (data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over-modulation. (Please refer to the BOM list or Schematics). 3. The modular transmitter has its own power supply regulation. (Please refer to the BOM list or Schematics). 4. The modular transmitter complies with the antenna requirements of Section 15.203 and 15.204(c). (Please review external photos or test report). 5. The modular transmitter is tested in a stand-alone configuration. (Please review test setup photos). 6. The modular transmitter is labeled with its own FCC ID number. (Please review label sample). 7. The modular transmitter complies with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. (The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are given in the Users Manual). 8. The modular transmitter complies with any applicable RF exposure requirements. (The EUT is compliant with all applicable RF exposure requirements. RF Exposure is addressed in the RF exposure exhibition). Signature: Name: Mrs. Rio Chen Title: Compliance Manger Company Name: HON HAI Precision IND. CO., LTD.

1 of 2 External Photos Model Number: TangoP1001 FCC ID: MCLT77Z29500 2 of 2 EUT Photo 1 ) EUT Photo 2 )

FOXCONN CONFIDENTIAL 2 XXXXXXX xxxxxxx.xx LF MO-VVSS Tango Label Pasted Location Bottom Side HH LabelP/N: 503.00583.005 FCC ID : MCLT77Z29500model : T ango P1001 MADE IN CHINA FCC LabelP/N: XXX.XXXXX.XXX FOXCONN CONFIDENTIAL 3 FCC Label Definition FCC Label Definition:1. Label Size: 37*27mm2. Material: 50# White Mylar3. P/N: XXX.XXXXX.XXX FCC ID : MCLT77Z29500model : TANGO P1001 MADE IN CHINA

1 of 2 Internal Photos Model Number: TangoP1001 FCC ID: MCLT77Z29500 2 of 2 EUT Photo 1 ) EUT Photo 2 )

A Test Lab Techno Corp. Changan Lab：No. 140 -1, Changan Street, Bade City, Taoyuan County, Taiwan R.O.C. Te l：886-3-271-0188 / Fax：886-3-271-0190 MPE Report Test Report No. ： 1208FS11-01 Applicant ： HON HAI Precision IND. CO., LTD. Manufacturer ： HON HAI Precision IND. CO., LTD. Product Type ： PCI-E Embedded Module Trade Name ： N/A Model Number ： TangoP1001 Dates of Received ： Jul. 17, 2012 Dates of Test ： Aug. 03, 2012 Dates of Issued ： Aug. 22, 2012 Test Specification ： 47 CFR § 2.1091 47 CFR §1.1310 ANSI / IEEE Std.C95.1-1992 Location of Test Lab. ： Chang-an Lab. 1. The test operations have to be performed with cautious behavior, the test results are as attached. 2. The test results are under chamber environment of A Test Lab Techno Corp. A Test Lab Techno Corp. does not assume responsibility for any conclusions and generalizations drawn from the test results with regard to other specimens or samples. 3. The measurement report has to be written approval of A Test Lab Techno Corp. It may only be reproduced or published in full. This report shall not be reproduced except in full, without the written approval of A Test Lab Techno Corp. 4. This document may be altered or revised by A Test Lab Techno. Corp. personnel only, and shall be noted in the revision section of the document. Approved By ： Tested By ： (Yung Tan Tsai ) (Bill Hu) Report Number: 1208FS11-01Page 1 of 12 ©2012 A Test Lab Techno Corp. Contents 1. Description of Equipment under Test (EUT)............................................................... 3 2. Human Exposure Assessment .................................................................................... 4 3. RF Output Power........................................................................................................... 5 4. Test Result....................................................................................................................11 Report Number: 1208FS11-01Page 2 of 12 ©2012 A Test Lab Techno Corp. 1. Description of Equipment under Test (EUT) Applicant HON HAI Precision IND. CO., LTD. Applicant Address 5F-1,5 Hsin-An Road Hsinchu, Science-Based Industrial Park Taiwan, R.O.C Manufacturer HON HAI Precision IND. CO., LTD. Manufacturer Address 5F-1,5 Hsin-An Road Hsinchu, Science-Based Industrial Park Taiwan, R.O.C Product Type PCI-E Embedded Module Trade Name N/A Model Number TangoP1001 FCC ID MCLT77Z29500 Hardware Version Rev.F Software Version P1001.3.03_0.1 Frequency Range 824.2 - 848.8 MHz GPRS/EGPRS 850 1850.2 - 1909.8 MHz GPRS/EGPRS 1900 1852.4 - 1907.6 MHz WCDMA(RMC 12.2K)/HSDPA/HSUPA Band II 826.4 - 846.6 MHz WCDMA(RMC 12.2K)/HSDPA/HSUPA Band V 1710 - 1755 MHz LTE Band 4 704 - 716 MHz LTE Band 17 Transmit Power GPRS/EGPRS 850: 1.778 W / 32.50 dBm (conducted power) GPRS/EGPRS 1900: 0.871 W / 29.40 dBm WCDMA(RMC 12.2K)/HSDPA/HSUPA Band II: 0.230 W / 23.62 dBm WCDMA(RMC 12.2K)/HSDPA/HSUPA Band V: 0.225 W / 23.53 dBm LTE Band 4: 0.201 W / 23.03 dBm LTE Band 17: 0.208 W / 23.18 dBm Antenna for test Tel Cab, T-AT314 Antenna Specification GSM 850: 2.14 dBi PCS 1900: 2.14 dBi WCDMA Band II: 2.14 dBi WCDMA Band V: 2.14 dBi LTE Band 4: 2.14 dBi LTE Band 17: 2.14 dBi Antenna Designation External Antenna Temperature Range -30 ~ +70°C The above equipment was tested by A Test Lab Techno Corp. For compliance with the requirements set forth in 47 CFR § 2.1091 & 47 CFR § 1.1310. The results of testing in this report apply only to the product/system, which was tested. Other similar equipment will not necessarily produce the same results due to production tolerance and measurement uncertainties Report Number: 1208FS11-01Page 3 of 12 ©2012 A Test Lab Techno Corp. 2. Human Exposure Assessment Due to the design and installation of this product, it is not possible to conduct SAR evaluation. This is because client either manufactures or supplies the antenna(s) that will be used in the installation of this product. Therefore, this product will be evaluated as a mobile device per 47 CFR §1.1310 titled “Radiofrequency radiation exposure limits”, generally referred to as MPE limits. In 47 CFR § 2.1091, paragraph (b) defines a mobile device as “a transmitting device designed to be used in other than fixed locations and to generally be used in such a way that a separation distance of at least 20 cm is normally maintained between the transmitter’s radiating structure(s) and the body of the user or nearby persons. ” This product is intended to be installed into a vehicle such that the unit is physically secured at one location. In the installation guide supplied with the product, Client has made the following statement: “IMPORTANT: To meet the FCC’s RF Exposure Guidelines, the antenna should be installed so there is at least 20 cm of separation between the body of the user and nearby persons and the antenna”. Based on the installation of the transceiver and the antenna, the transmitters radiating structure is more than 20 cm from the user. Thus, this product is a “mobile device” as defined in section § 2.1091 paragraph (b). Exposure evaluation Equation from page 18 of OET Bulletin 65, Edition 97-01 2 4R PG S π = Where S: power density P: power input to the antenna G: power gain of the antenna in the direction of interest relative to an isotropic radiator. R: distance to the center of radiation of the antenna. Report Number: 1208FS11-01Page 4 of 12 ©2012 A Test Lab Techno Corp. 3. RF Output Power Band Date Rate CH Frequency (MHz) Conducted power Avg.-Burst (dBm) Worst Case 128 824.2 32.40 □ 190 836.6 32.50 ■ 4Down1Up Duty factor 1/8 251 848.8 32.40 □ 128 824.2 30.50 □ 190 836.6 30.10 □ 3Down2Up Duty factor 2/8 251 848.8 29.80 □ 128 824.2 28.60 □ 190 836.6 28.40 □ 2Down3Up Duty factor 3/8 251 848.8 28.00 □ 128 824.2 27.40 □ 190 836.6 27.10 □ GPRS850 1Down4Up Duty factor 4/8 251 848.8 26.90 □ 128 824.2 27.40 □ 190 836.6 27.50 ■ 4Down1Up Duty factor 1/8 251 848.8 27.30 □ 128 824.2 25.40 □ 190 836.6 25.20 □ 3Down2Up Duty factor 2/8 251 848.8 25.10 □ 128 824.2 23.4…

Text truncated - open the document above for the full version.

FCC 47 CFR PART 22H and 24E Product Type ： PCI-E Embedded Module Applicant ： HON HAI Precision IND. CO., LTD. Address ： 5F-1,5 Hsin-An Road Hsinchu, Science-Based Industrial Park Taiwan, R.O.C Model Number ： TangoP1001 Test Specification ： FCC 47 CFR PART 22H: Oct, 2011 FCC 47 CFR PART 24E: Oct, 2011 ANSI/TIA-603-C-2004 Application Purpose ： Original Receive Date ： Jul. 17, 2012 Issue Date ： Aug. 22, 2012 Issue by A Test Lab Techno Corp. No. 140-1, Changan Street, Bade City, Taoyuan County 334, Taiwan R.O.C. Te l：+886-3-2710188 / Fax：+886-3-2710190 T aiwan Accreditation Foundation accreditation number: 1330 Note: This report shall not be reproduced except in full, without the written approval of A Test Lab Techno Corp. This document may be altered or revised by A Test Lab Techno Corp. personnel only, and shall be noted in the revision section of the document. The client should not use it to claim product endorsement by TAF, or any government agencies. The test results in the report only apply to the tested sample. Report Number: 1207FR24-01 1/115 A Test Lab Techno Corp. Revision History Rev. Issue Date Revisions Revised By 00 Aug. 15, 2012 Initial Issue 01 Aug. 22, 2012 Revise Model Number Queenie Yang Report Number: 1207FR24-01 2/115 A Test Lab Techno Corp. Verification of Compliance Issued Date: 08/22/2012 Product Type : PCI-E Embedded Module Applicant : HON HAI Precision IND. CO., LTD. Address : 5F-1,5 Hsin-An Road Hsinchu, Science-Based Industrial Park Taiwan, R.O.C Model Number : TangoP1001 FCC ID : MCLT77Z29500 EUT Rated Voltage : DC 3.3V Test Voltage : 120 Vac / 60 Hz Applicable Standard : FCC 47 CFR PART 22H: Oct, 2011 FCC 47 CFR PART 24E: Oct, 2011 ANSI/TIA-603-C-2004 Application Purpose : Original Test Result : Complied Performing Lab. : A Test Lab Techno Corp. No. 140-1, Changan Street, Bade City, Taoyuan County 334, Taiwan R.O.C. Te l：+886-3-2710188 / Fax：+886-3-2710190 T aiwan Accreditation Foundation accreditation number: 1330 http://www.atl-lab.com.tw/e-index.htm The above equipment was tested by A Test Lab Techno Corp. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4: 2009 and the energy emitted by the sample tested as described in this report is in compliance with the requirements of FCC Rules Part 22H, Part 24E. The test results of this report relate only to the tested sample identified in this report. Approved By ： Reviewed By ： (Manager) (Murphy Wang) (Testing Engineer) (Fly Lu) Report Number: 1207FR24-01 3/115 A Test Lab Techno Corp. TABLE OF CONTENTS 1 General Information ....................................................................................................................................... 6 1.1. EUT Description .................................................................................................................................. 6 1.2. Mode of Operation .............................................................................................................................. 7 1.3. EUT Exercise Software....................................................................................................................... 7 1.4. Configuration of Test System Details .................................................................................................. 8 1.5. Test Site Environment ......................................................................................................................... 8 1.6. Summary of Test Result ...................................................................................................................... 9 2 RF Output Power Test ................................................................................................................................. 10 2.1. Limit................................................................................................................................................... 10 2.2. Test Instruments ................................................................................................................................ 10 2.3. Test Setup ......................................................................................................................................... 10 2.4. Test Procedure .................................................................................................................................. 10 2.5. Uncertainty .........................................................................................................................................11 2.6. Test Result .........................................................................................................................................11 3 Effective Radiated Power / Equivalent Isotropic Radiated Power Test .................................................. 15 3.1. Limit................................................................................................................................................... 15 3.2. Test Instruments ................................................................................................................................ 15 3.3. Setup ................................................................................................................................................. 16 3.4. Test Procedure .................................................................................................................................. 17 3.5. Uncertainty ........................................................................................................................................ 17 3.6. Test Result ........................................................................................................................................ 18 4 Occupied Bandwidth Test ...........................................................................................................................…

Text truncated - open the document above for the full version.

FCC 47 CFR PART 27 SUBPART L Product Type ： PCI-E Embedded Module Applicant ： HON HAI Precision IND. CO., LTD. Address ： 5F-1,5 Hsin-An Road Hsinchu, Science-Based Industrial Park Taiwan, R.O.C Trade Name ： N/A Model Number ： TangoP1001 Test Specification ： FCC 47 CFR PART 27 SUBPART L: Oct. 2011 ANSI C63.4: 2009 ANSI/TIA-603-C-2004 Application Purpose ： Original Receive Date ： Jul. 17, 2012 Issue Date ： Aug. 22, 2012 Issue by A Test Lab Techno Corp. No. 140-1, Changan Street, Bade City, Taoyuan County 334, Taiwan R.O.C. Te l：+886-3-2710188 / Fax：+886-3-2710190 T aiwan Accreditation Foundation accreditation number: 1330 Note: This report shall not be reproduced except in full, without the written approval of A Test Lab Techno Corp. This document may be altered or revised by A Test Lab Techno Corp. personnel only, and shall be noted in the revision section of the document. The client should not use it to claim product endorsement by TAF, or any government agencies. The test results in the report only apply to the tested sample. Report Number: 1208FR13-01 1/68 A Test Lab Techno Corp. Revision History Rev. Issue Date Revisions Revised By 00 Aug. 15, 2012 Initial Issue 01 Aug. 22, 2012 Revise Model Number Queenie Yang Report Number: 1208FR13-01 2/68 A Test Lab Techno Corp. Verification of Compliance Issued Date: 08/22/2012 Product Type : PCI-E Embedded Module Applicant : HON HAI Precision IND. CO., LTD. Address : 5F-1,5 Hsin-An Road Hsinchu, Science-Based Industrial Park Taiwan, R.O.C Trade Name : N/A Model Number : TangoP1001 FCC ID : MCLT77Z29500 EUT Rated Voltage : DC 3.3V Test Voltage : 120 Vac / 60 Hz Applicable Standard : FCC 47 CFR PART 27 SUBPART L: Oct. 2011 ANSI C63.4: 2009 ANSI/TIA-603-C-2004 Test Result : Complied Application Purpose : Original Performing Lab. : A Test Lab Techno Corp. No. 140-1, Changan Street, Bade City, Taoyuan County 334, Taiwan R.O.C. Te l：+886-3-2710188 / Fax：+886-3-2710190 T aiwan Accreditation Foundation accreditation number: 1330 http://www.atl-lab.com.tw/e-index.htm The above equipment was tested by A Test Lab Techno Corp. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4: 2009 and the energy emitted by the sample tested as described in this report is in compliance with the requirements of FCC Rules Part 27L. The test results of this report relate only to the tested sample identified in this report. Approved By ： Reviewed By ： (Manager) (Murphy Wang) (Testing Engineer) (Fly Lu) Report Number: 1208FR13-01 3/68 A Test Lab Techno Corp. TABLE OF CONTENTS 1 General Information................................................................................................................................. 6 1.1. EUT Description .................................................................................................................................. 6 1.2. Mode of Operation............................................................................................................................... 7 1.3. EUT Exercise Software....................................................................................................................... 8 1.4. Configuration of Test System Details .................................................................................................. 8 1.5. Test Site Environment ......................................................................................................................... 8 1.6. Summary of Test Result ...................................................................................................................... 9 2 Conducted Output Average Power Test.............................................................................................. 10 2.1. Limit ................................................................................................................................................... 10 2.2. Test Instruments ................................................................................................................................ 10 2.3. Test Setup.......................................................................................................................................... 10 2.4. Test Procedure .................................................................................................................................. 10 2.5. Uncertainty ........................................................................................................................................ 10 2.6. Test Result......................................................................................................................................... 11 3 Effective Radiated Power / Equivalent Isotropic Radiated Power Test............................................ 13 3.1. Limit ................................................................................................................................................... 13 3.2. Test Instruments ................................................................................................................................ 13 3.3. Test Setup.......................................................................................................................................... 13 3.4. Test Procedure .................................................................................................................................. 15 3.5. Uncertainty ........................................................................................................................................ 15 3.6. Test Result......................................................................................................................................... 16 4 Frequency Stability Test ....................................................................................................................... 17 4.1. Limit ............…

Text truncated - open the document above for the full version.

Part 22H & Part 24E Test Setup Photographs Radiated Emissions Test Configuration: Below 1GHz _ Front View Below 1GHz _ Rear View Report Number: 1207FR24-01 1/3 A Test Lab Techno Corp. Below 1GHz _ Close View Above 1GHz _ Front View Report Number: 1207FR24-01 2/3 A Test Lab Techno Corp. Above 1GHz _ Rear View Above 1GHz _ Close View Report Number: 1207FR24-01 3/3 A Test Lab Techno Corp.

Part 27L Test Setup Photographs Radiated Emissions Test Configuration: Below 1GHz _ Front View Below 1GHz _ Rear View A Test Lab Techno Corp. Report Number: 1208FR13 1/3 Above 1GHz _ Front View Above 1GHz _ Rear View A Test Lab Techno Corp. Report Number: 1208FR13 2/3 A Test Lab Techno Corp. Report Number: 1208FR13 3/3 Close View