MCLWINA1WiFi 11b/g/n Module

Confidential 1 WIN-A1 WIFI Module User Manual Rev. 0.0 Confidential 2 1. Introduction The WIN-A1 802.11b/g/n module provides wireless modem functionality utilizing direct sequence spread spectrum and OFDM/CCK technology. The objective of this use manual is to verify the functionality of the WIN-A1 802.11b/g/n module RF/Digital electronic design against the design specifications. This revision includes results taken at various temperatures (0ႂ,25 ႂ,70 ႂ) and voltages (3.0V,3.3V,3.6V). Included are statements of test purpose, test methodologies, test modes and parameters, environmental conditions, applicable specifications, and typical reference design performance. The major specifications and documents are listed below and upon to update in the following new revisions.  802.11b: IEEE Std 802.11b/D8.0-Sept 2001 Part 11 Paragraph 18.4.7.3  802.11g: IEEE Std 802.11g/D8.2-Apr 2003 Part 11 Paragraph 19.5.4  802.11n: IEEE P802.11n/D2.07-Mar 2006 Paragraph 20.3.20.1 Confidential 3 2.Mechanical Drawing Confidential 4 3. Regulatory Information USA-Federal Communications Commission (FCC) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Labeling Hon Hai Precision WiFi 11b/g/n module WIN-A1 labelled as below. FCC ID: MCLWINA1 The proposed with FCC ID label format is to be placed on the module. If FCC ID is not visible when the module is installed into the system, “Contains FCC ID: MCLWINA1” shall be placed on the outside of final host system. Caution: Exposure to Radio Frequency Radiation. To comply with FCC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. This device must not be co-located or operating in conjunction with any other antenna or transmitter. Canada-Industry Canada (IC) This device complies with RSS 210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of this device. The term “IC” before the equipment certification number only signifies that the Industry Canada technical specifications were met. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (EIRP) is not more than that required for successful communication. Confidential 5 To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing. Caution: Exposure to Radio Frequency Radiation. To comply with IC RF exposure compliance requirements, a separation distance of at least 20 cm must be maintained between the antenna of this device and all persons. This device must not be co-located or operating in conjunction with any other antenna or transmitter.

Applicant/Grantee Hon Hai Precision Ind. Co.,Ltd. FCC ID: MCLWINA1 Section 15.212 Modular Transmitters Request for Modular Approval Request for Limited Modular Approval Requirements EUT Conditions Comply (Y/N) Single Modular Approval Requirements 1 The radio elements of the modular transmitter must have their own shielding. The physical crystal and tuning capacitors may be located external to the shielded radio elements. The device is equipped with Metal shielding to cover RF section. Refer to external photos Y 2 The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over- modulation. All inputs to the device are buffered through logic U1 inputs. Refer to Schematic Diagram. Y 3 The modular transmitter must have its own power supply regulation. The device is equipped with Internal 1.8VDC regulator. Refer to Block Diagram. Y 4 The modular transmitter must comply with the antenna and transmission system requirements of Sections 15.203, 15.204(b) and 15.204(c). The antenna must either be permanently attached or employ a “unique” antenna coupler (at all connections between the module and the antenna, including the cable). The “professional installation” provision of Section 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph (b) of this section. Device is equipped with unique antenna (part number: KK23017- 01-7F,verdor: FOXCONN.) Y 5 The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing for compliance with Part 15 requirements. Unless the transmitter module will be battery powered, it must comply with the AC line conducted requirements found in Section 15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module (see Section 15.27(a)). The length of these lines shall be the length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available (see Section 15.31(i)). The device was tested outside of the Desktop PC for full modular approval. Refer to setup photos. Y 6 The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number. (A) If using a permanently affixed label, the modular transmitter must be labeled with its own FCC identification number, and, if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: XYZMODEL1” or “Contains FCC ID: XYZMODEL1.” Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. (B) If the modular transmitter uses an electronic display of the FCC identification number, the information must be readily accessible and visible on the modular transmitter or on the device in which it is installed. If the module is installed inside another device, then the outside of the device into which the module is installed must display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains FCC certified transmitter module(s).” Any similar wording that expresses the same meaning may be used. The user manual must include instructions on how to access the electronic display. A copy of these instructions must be included in the application for equipment authorization. The proposed FCC ID label format is to be placed on the module. If FCC ID is not visible when the module is installed into the system, “Contains FCC ID: MCLWINA1” shall be placed on the outside of final host system. Y 7 The modular transmitter must comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. Refer to “User’s Guide” Exhibit Y 8 The modular transmitter must comply with any applicable RF exposure requirements in its final configuration. The device complies with RF exposure compliance requirement Y A limited modular approval may be granted for single or split modular transmitters that do not comply with all of the above requirements, e.g., shielding, minimum signaling amplitude, buffered modulation/data inputs, or power supply regulation, if the manufacturer can demonstrate by alternative means in the application for equipment authorization that the modular transmitter meets all the applicable Part 15 requirements under the operating conditions in which the transmitter will be used. Limited modular approval also may be granted in those instances where compliance with RF exposure rules is demonstrated only for particular product configurations. The applicant for certification must state how control of the end product into which the module will be installed will be maintained such that full compliance of the end product is always ensured.

WiFi 11b/g/n module : WIN-A1 FCC ID: MCLWINA1 IC: 2878D-WINA1 External Photos

WiFi 11b/g/n module : WIN-A1 FCC ID: MCLWINA1 IC: 2878D-WINA1 Label & Label location XXXWWXXXX

WiFi 11b/g/n module : WIN-A1 FCC ID: MCLWINA1 IC: 2878D-WINA1 Internal Photos

FCC CFR47 PART 15 SUBPART C INDUSTRY CANADA RSS-210 ISSUE 7 CERTIFICATION TEST REPORT FOR WIFI 11B/G/N MODULE MODEL NUMBER: WIN-A1 FCC ID: MCLWINA1 IC: 2878D-WINA1 REPORT NUMBER: 10J13452-1 ISSUE DATE: OCTOBER 12, 2010 Prepared for HON HAI PRECISION IND. CO., LTD. 5F-1, 5 HSIN-AN ROAD HSINCHU SCIENCE-BASED INDUSTRIAL PARK, R.O.C., TAIWAN Prepared by COMPLIANCE CERTIFICATION SERVICES (UL CCS) 47173 BENICIA STREET FREMONT, CA 94538, U.S.A. TEL: (510) 771-1000 FAX: (510) 661-0888 REPORT NO: 10J13452-1 DATE: OCTOBER 12, 2010 FCC ID: MCLWINA1 IC: 2878D-WINA1 Page 2 of 86 COMPLIANCE CERTIFICATION SERVICES (UL CCS) FORM NO: CCSUP4701C 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. Revision History Rev. Issue Date Revisions Revised By --- 10/12/10 Initial Issue T. Chan REPORT NO: 10J13452-1 DATE: OCTOBER 12, 2010 FCC ID: MCLWINA1 IC: 2878D-WINA1 Page 3 of 86 COMPLIANCE CERTIFICATION SERVICES (UL CCS) FORM NO: CCSUP4701C 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS.................................................................................... 5 2. TEST METHODOLOGY ........................................................................................................ 6 3. FACILITIES AND ACCREDITATION.................................................................................... 6 4. CALIBRATION AND UNCERTAINTY .................................................................................. 6 4.1. MEASURING INSTRUMENT CALIBRATION ............................................................... 6 4.2. SAMPLE CALCULATION.............................................................................................. 6 4.3. MEASUREMENT UNCERTAINTY................................................................................ 6 5. EQUIPMENT UNDER TEST ................................................................................................. 7 5.1. DESCRIPTION OF EUT................................................................................................ 7 5.2. MAXIMUM OUTPUT POWER....................................................................................... 7 5.3. DESCRIPTION OF AVAILABLE ANTENNAS............................................................... 7 5.4. SOFTWARE AND FIRMWARE..................................................................................... 7 5.5. WORST-CASE CONFIGURATION AND MODE .......................................................... 7 5.6. DESCRIPTION OF TEST SETUP................................................................................. 8 6. TEST AND MEASUREMENT EQUIPMENT ....................................................................... 10 7. ANTENNA PORT TEST RESULTS .................................................................................... 11 7.1. 802.11b MODE IN THE 2.4 GHz BAND...................................................................... 11 7.1.1. 6 dB BANDWIDTH .............................................................................................. 11 7.1.2. 99% BANDWIDTH .............................................................................................. 14 7.1.3. OUTPUT POWER ............................................................................................... 17 7.1.4. AVERAGE POWER ............................................................................................ 18 7.1.5. POWER SPECTRAL DENSITY .......................................................................... 19 7.1.6. CONDUCTED SPURIOUS EMISSIONS............................................................. 22 7.2. 802.11g MODE IN THE 2.4 GHz BAND...................................................................... 26 7.2.1. 6 dB BANDWIDTH .............................................................................................. 26 7.2.2. 99% BANDWIDTH .............................................................................................. 29 7.2.3. OUTPUT POWER ............................................................................................... 32 7.2.4. AVERAGE POWER ............................................................................................ 33 7.2.5. POWER SPECTRAL DENSITY .......................................................................... 34 7.2.6. CONDUCTED SPURIOUS EMISSIONS............................................................. 37 7.3. 802.11n HT20 SISO MODE IN THE 2.4 GHz BAND .................................................. 41 7.3.1. 6 dB BANDWIDTH .............................................................................................. 41 7.3.2. 99% BANDWIDTH .............................................................................................. 44 7.3.3. OUTPUT POWER ............................................................................................... 47 7.3.4. AVERAGE POWER ............................................................................................ 48 7.3.5. POWER SPECTRAL DENSITY .......................................................................... 49 7.3.6. CONDUCTED SPURIOUS EMISSIONS............................................................. 52 8. RADIATED TEST RESULTS .............................................................................................. 56 REPORT NO: 10J13452-1 DATE: OCTOBER 12, 2010 FCC ID: MCLWINA1 IC: 2878D-WINA1 Page 4 of 86 COMPLIANCE CERTIFICATION SERVICES (UL CCS) FORM NO: CCSUP4701C 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. 8.1. LIMITS AND PROCEDURE ................................................................…

Text truncated - open the document above for the full version.

REPORT NO: 10J13452-1 DATE: OCTOBER 12, 2010 FCC ID: MCLWINA1 IC: 2878D-WINA1 Page 81 of 86 COMPLIANCE CERTIFICATION SERVICES (UL CCS) FORM NO: CCSUP4701C 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. 11. SETUP PHOTOS ANTENNA PORT CONDUCTED RF MEASUREMENT SETUP RADIATED RF MEASUREMENT SETUP FOR PORTABLE CONFIGURATION ANTENNA PORT CONDUCTED PHOTO X-AXIS WITH LONG ENDS AT REAR PHOTO REPORT NO: 10J13452-1 DATE: OCTOBER 12, 2010 FCC ID: MCLWINA1 IC: 2878D-WINA1 Page 82 of 86 COMPLIANCE CERTIFICATION SERVICES (UL CCS) FORM NO: CCSUP4701C 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. X-AXIS WITH LONG ENDS AT FRONT PHOTO Y-AXIS WITH LONG ENDS AT RIGHT PHOTO REPORT NO: 10J13452-1 DATE: OCTOBER 12, 2010 FCC ID: MCLWINA1 IC: 2878D-WINA1 Page 83 of 86 COMPLIANCE CERTIFICATION SERVICES (UL CCS) FORM NO: CCSUP4701C 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. Y-AXIS WITH LONG END AT LEFT PHOTO Z-AXIS WITH LONG ENDS AT TOP PHOTO REPORT NO: 10J13452-1 DATE: OCTOBER 12, 2010 FCC ID: MCLWINA1 IC: 2878D-WINA1 Page 84 of 86 COMPLIANCE CERTIFICATION SERVICES (UL CCS) FORM NO: CCSUP4701C 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. RADIATED RF MEASUREMENT SETUP Z-AXIS WITH LONG ENDS AT BOTTOM PHOTO RADIATED FRONT PHOTO REPORT NO: 10J13452-1 DATE: OCTOBER 12, 2010 FCC ID: MCLWINA1 IC: 2878D-WINA1 Page 85 of 86 COMPLIANCE CERTIFICATION SERVICES (UL CCS) FORM NO: CCSUP4701C 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. POWERLINE CONDUCTED EMISSIONS MEASUREMENT SETUP RADIATED BACK PHOTO LINE CONDUCTED FRONT PHOTO REPORT NO: 10J13452-1 DATE: OCTOBER 12, 2010 FCC ID: MCLWINA1 IC: 2878D-WINA1 Page 86 of 86 COMPLIANCE CERTIFICATION SERVICES (UL CCS) FORM NO: CCSUP4701C 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of UL CCS. END OF REPORT LINE CONDUCTED BACK PHOTO