MUH-SKYPORT2ColorTouch

Model THERM-500 Owner’s Manual & Installation Guide i FCC Compliance Statement This equipment has been tested and found to comply with the limits for an intentional radiator, pursuant to Part 15, subpart C of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference in radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that of the receiver. • Consult the dealer or an experienced radio or TV technician for help. Notice: Only peripherals complying with FCC limits may be attached to this equipment. Operation with noncompliant peripherals or peripherals not recommended by First Alert / BRK Brands, Inc. is likely to result in interference to radio and TV reception. Changes or modifications to the product, not expressly approved by First Alert / BRK Brands, Inc. could void the user’s authority to operate the equipment. FCC - INDOOR Mobile Radio Information: To comply with FCC/IC RF exposure limits for general population / uncontrolled exposure, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. This Device complies with Industry Canada License-exempt RSS standard(s). Operation is subject to the following two conditions: 1) this device may not cause interference, and 2) this device must accept any interference, including interference that may cause undesired operation of the device. Follow the Installation Instructions before proceeding. Set the thermostat mode to “OFF” prior to changing settings in setup or restoring Factory Defaults. CAUTION This color touchscreen has the ability to receive updates to its firmware. Periodically firmware updates are released by the manufacturer to add features and/or performance enhancements. This manual was produced reflecting the most current firmware/feature set at the time of publication, firmware rev. 3.04. Firmware releases after rev. 3.04 may not be adequately depicted in this manual. Please refer to the appropriate website or contact your place of purchase to learn about changes to the thermostat after firmware release 3.04. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Cet appareil est conforme avec Industrie Canada, exempts de licence standard RSS(s). Son fonctionnement est soumis aux deux conditions suivantes: 1) ce dispositif ne doit pas causer d’interférences, et 2) ce dispositif doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais fonctionnement de l’appareil. En vertu des règlements d’Industrie Canada, cet émetteur de radio ne peut fonctionner en utilisant une antenne d’un type et maximale (ou moins) Gain approuvé pour l’émetteur par Industrie Canada. Pour réduire les interférences radio potentielles aux autres utilisateurs , le type d’antenne et son gain doivent être choisis afin que la puissance isotrope rayonnée équivalente (PIRE) ne est pas plus de ce qui est nécessaire pour une communication réussie. We, First Alert /BRK Brands, Inc. declare under our sole responsibility that the device to which this declaration relates: Complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. ii iii Glossary of Terms Auto-Changeover: A mode in which the thermostat will turn on the heating or cooling based on room temperature demand. Cool Setpoint: The warmest temperature that the space should rise to before cooling is turned on (without regard to deadband). Deadband: The number of degrees the thermostat will wait, once a setpoint has been reached, before energizing heating or cooling. Differential: The forced temperature difference between the heat setpoint and the cool setpoint. Heat Setpoint: The coolest temperature that the space should drop to before heating is turned on (without regard to deadband). Icon: The word or symbol that appears on the thermostat display. Mode: The current operating condition of the thermostat (i.e. Off, Heat, Cool, Auto, Program On). Non-Programmable Thermostat: A thermostat that does not have the capability of running Time Period Programming. Programmable Thermostat: A thermostat that has the capability of running Time Period Programming. Temperature Swing: Same as Deadband. Time Period Programming: A program that allows the thermostat to automatically adjust the heat setpoint and/or the cool setpoint based on the time of the day. Same as Schedule. iv Table of Contents GET TO KNOW YOUR THERMOSTAT Home Screen ...............................................................................................1 Menu Screens .............................................................................................1 Dropdown Dashboard ...............…

Text truncated - open the document above for the full version.

Model THERM-500B Owner’s Manual & Installation Guide i FCC Compliance Statement This equipment has been tested and found to comply with the limits for an intentional radiator, pursuant to Part 15, subpart C of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference in radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that of the receiver. • Consult the dealer or an experienced radio or TV technician for help. Notice: Only peripherals complying with FCC limits may be attached to this equipment. Operation with noncompliant peripherals or peripherals not recommended by Bionaire / BRK Brands, Inc. is likely to result in interference to radio and TV reception. Changes or modifications to the product, not expressly approved by Bionaire / BRK Brands, Inc. could void the user’s authority to operate the equipment. FCC - INDOOR Mobile Radio Information: To comply with FCC/IC RF exposure limits for general population / uncontrolled exposure, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. This Device complies with Industry Canada License-exempt RSS standard(s). Operation is subject to the following two conditions: 1) this device may not cause interference, and 2) this device must accept any interference, including interference that may cause undesired operation of the device. Follow the Installation Instructions before proceeding. Set the thermostat mode to “OFF” prior to changing settings in setup or restoring Factory Defaults. CAUTION This color touchscreen has the ability to receive updates to its firmware. Periodically firmware updates are released by the manufacturer to add features and/or performance enhancements. This manual was produced reflecting the most current firmware/feature set at the time of publication, firmware rev. 3.04. Firmware releases after rev. 3.04 may not be adequately depicted in this manual. Please refer to the appropriate website or contact your place of purchase to learn about changes to the thermostat after firmware release 3.04. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Cet appareil est conforme avec Industrie Canada, exempts de licence standard RSS(s). Son fonctionnement est soumis aux deux conditions suivantes: 1) ce dispositif ne doit pas causer d’interférences, et 2) ce dispositif doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais fonctionnement de l’appareil. En vertu des règlements d’Industrie Canada, cet émetteur de radio ne peut fonctionner en utilisant une antenne d’un type et maximale (ou moins) Gain approuvé pour l’émetteur par Industrie Canada. Pour réduire les interférences radio potentielles aux autres utilisateurs , le type d’antenne et son gain doivent être choisis afin que la puissance isotrope rayonnée équivalente (PIRE) ne est pas plus de ce qui est nécessaire pour une communication réussie. We, Bionaire/BRK Brands, Inc. declare under our sole responsibility that the device to which this declaration relates: Complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. ii iii Glossary of Terms Auto-Changeover: A mode in which the thermostat will turn on the heating or cooling based on room temperature demand. Cool Setpoint: The warmest temperature that the space should rise to before cooling is turned on (without regard to deadband). Deadband: The number of degrees the thermostat will wait, once a setpoint has been reached, before energizing heating or cooling. Differential: The forced temperature difference between the heat setpoint and the cool setpoint. Heat Setpoint: The coolest temperature that the space should drop to before heating is turned on (without regard to deadband). Icon: The word or symbol that appears on the thermostat display. Mode: The current operating condition of the thermostat (i.e. Off, Heat, Cool, Auto, Program On). Non-Programmable Thermostat: A thermostat that does not have the capability of running Time Period Programming. Programmable Thermostat: A thermostat that has the capability of running Time Period Programming. Temperature Swing: Same as Deadband. Time Period Programming: A program that allows the thermostat to automatically adjust the heat setpoint and/or the cool setpoint based on the time of the day. Same as Schedule. iv Table of Contents GET TO KNOW YOUR THERMOSTAT Home Screen ...............................................................................................1 Menu Screens .............................................................................................1 Dropdown Dashboard ........................…

Text truncated - open the document above for the full version.

EXTERNAL PHOTOS Company Name Venstar Inc. Model # THERM‐500, THERM‐500B, T7850,T7900, T8850, T8900 FCC ID # MUH‐SKYPORT2 IC # 12547A‐SKYPORT2 Page 1 of 2 EXTERNAL PHOTOS Company Name Venstar Inc. Model # THERM‐500, THERM‐500B, T7850,T7900, T8850, T8900 FCC ID # MUH‐SKYPORT2 IC # 12547A‐SKYPORT2 Page 2 of 2

Monday, November 17, 2014 14:43:05

INTERNAL PHOTOS Company Name Venstar Inc. Model # THERM‐500, THERM‐500B, T7850,T7900, T8850, T8900 FCC ID # MUH‐SKYPORT2 IC # 12547A‐SKYPORT2 Page 1 of 5 Inside view of back cover plate INTERNAL PHOTOS Company Name Venstar Inc. Model # THERM‐500, THERM‐500B, T7850,T7900, T8850, T8900 FCC ID # MUH‐SKYPORT2 IC # 12547A‐SKYPORT2 Page 2 of 5 Close up with shield top removed INTERNAL PHOTOS Company Name Venstar Inc. Model # THERM‐500, THERM‐500B, T7850,T7900, T8850, T8900 FCC ID # MUH‐SKYPORT2 IC # 12547A‐SKYPORT2 Page 3 of 5 Close up with shield completely removed INTERNAL PHOTOS Company Name Venstar Inc. Model # THERM‐500, THERM‐500B, T7850,T7900, T8850, T8900 FCC ID # MUH‐SKYPORT2 IC # 12547A‐SKYPORT2 Page 4 of 5 Antenna Close up INTERNAL PHOTOS Company Name Venstar Inc. Model # THERM‐500, THERM‐500B, T7850,T7900, T8850, T8900 FCC ID # MUH‐SKYPORT2 IC # 12547A‐SKYPORT2 Page 5 of 5

W66 N220 Commerce Court ● Cedarburg, WI 53012 USA ● Phone: 262.375.4400 ● Fax: 262.375.4248 ● www.lsr.com Prepared For: Venstar Name: ColorTouch Report: RF314318 B FCC RF Model: TERM-500 LSR: C-2052 Serial: Eng Sample Page 1 of 8 i. Title Page ENGINEERING TEST REPORT # 314318 B LSR Job #: C-2052 RF Exposure Compliance of: ColorTouch Test Date(s): November 14 th , December 1 st -4 th , 2014 Prepared For: Venstar USA Attn: Steve Dushane 9250 Owensmouth Avenue Chatsworth, CA 91311 This Test Report is issued under the Authority of: Shane D. Rismeyer, EMC Engineer Signature: Date: 1/27/15 This Test Report may not be reproduced, except in full, without written approval of LS Research, LLC. Prepared For: Venstar Name: ColorTouch Report: RF314318 B FCC RF Model: TERM-500 LSR: C-2052 Serial: Eng Sample Page 2 of 8 ii. Table of Contents Table of Contents i. Title Page ................................................................................................................................... 1 ii. Table of Contents ....................................................................................................................... 2 iii. LS Research, LLC ...................................................................................................................... 3 1.0 Conformance Summary ............................................................................................................. 4 2.0 SAR Test Exclusion Threshold .................................................................................................. 4 3.0 Client Information ...................................................................................................................... 5 3.1 Equipment Under Test (EUT) Information ................................................................................ 5 3.2 Product Description ................................................................................................................... 5 3.3 Modifications Incorporated In the EUT for Compliance Purposes ........................................... 5 3.4 Deviations & Exclusions from Test Specifications ................................................................... 5 3.5 Additional Information .............................................................................................................. 5 4.0 RF Conducted Measurement Data ............................................................................................. 6 5.0 SAR Test Exclusion Calculation ............................................................................................... 6 6.0 MPE Calculation ........................................................................................................................ 8 Prepared For: Venstar Name: ColorTouch Report: RF314318 B FCC RF Model: TERM-500 LSR: C-2052 Serial: Eng Sample Page 3 of 8 iii. LS Research, LLC LSR, LLC in Review As an EMC Testing Laboratory, our Accreditation and Assessments are recognized through the following: A2LA – American Association for Laboratory Accreditation Accreditation based on ISO/IEC 17025: 2005 with Electrical (EMC) Scope of Accreditation A2LA Certificate Number: 1255.01 Federal Communications Commission (FCC) – USA Listing of 3 Meter Semi-Anechoic Chamber based on Title 47 CFR – Part 2.948 FCC Registration Number: 90756 Industry Canada On file, 3 Meter Semi-Anechoic Chamber based on RSS-212 – Issue 1 File Number: IC 3088-A On file, 3 and 10 Meter OATS based on RSS-212 – Issue 1 File Number: IC 3088 U. S. Conformity Assessment Body (CAB) Validation Validated by the European Commission as a U. S. Competent Body operating under the U. S./EU, Mutual Recognition Agreement (MRA) operating under the European Union Electromagnetic Compatibility –Council Directive 2004/108/EC (formerly 89/336/EEC, Article 10.2). Date of Validation: January 16, 2001 Validated by the European Commission as a U.S. Notified Body operating under the U.S. /EU, Mutual Recognition Agreement (MRA) operating under the European Union Telecommunication Equipment – Council Directive 99/5/EC, Annex V. Date of Validation: November 20, 2002 Notified Body Identification Number: 1243 Prepared For: Venstar Name: ColorTouch Report: RF314318 B FCC RF Model: TERM-500 LSR: C-2052 Serial: Eng Sample Page 4 of 8 1.0 Conformance Summary The EUT was found to MEET the 5mm minimum test separation distance threshold for SAR test exclusion per FCC §2.1091(mobile) using methods of FCC KDB 447498 D01 General RF Exposure Guidance v05r02 as a standalone device. 2.0 SAR Test Exclusion Threshold SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 20 cm 1-g SAR test exclusion threshold equation: [(max. power of channel, including tune-up tolerance, mW) / (min. test separation distance, mm)] * [√f(GHz)] ≤ 3.0 10-g SAR test exclusion threshold equation: [(max. power of channel, including tune-up tolerance, mW) / (min. test separation distance, mm)] * [√f(GHz)] ≤ 7.5 Prepared For: Venstar Name: ColorTouch Report: RF314318 B FCC RF Model: TERM-500 LSR: C-2052 Serial: Eng Sample Page 5 of 8 3.0 Client Information Manufacturer Name: Venstar Address: 9250 Owensmouth Ave. Contact Person: Steve Dushane 3.1 Equipment Under Test (EUT) Information The following information has been supplied by the applicant. Product Name: ColorTouch Model Number: THERM-500 Serial Number: Eng Sample FCC ID MUH-SKYPORT2 3.2 Product Description Color Touch thermostat is a controller used with HVAC system to regulate temperature and/or humidity. This thermostat incorporates an on-board Wi-Fi transceiver, which allows the user to observe temperature and humidity information using a remote device. 3.3 Modifications Incorporated In the EUT for Compliance Purposes None noted at time of test 3.4 Deviations & Exclusions from Test Specifications None noted at time of test 3.5 Additional Information Low Channel 1(2412 MHz), Middle Channel 6 (2437 MHz), High Channel 11 (2462 MHz). EUT progr…

Text truncated - open the document above for the full version.

W66 N220 Commerce Court ● Cedarburg, WI 53012 Phone: 262.375.4400 ● Fax: 262.375.4248 www.lsr.com ENGINEERING TEST REPORT # 314318 LSR Job #: C-2052 Compliance Testing of: ColorTouch Test Date(s): November 14 th , December 1 st -4 th , 2014 Prepared For: Venstar USA Attn: Steve Dushane 9250 Owensmouth Avenue Chatsworth, CA 91311 This Test Report is issued under the Authority of: Shane D. Rismeyer, EMC Engineer Signature: Date: 1/27/15 Test Report Reviewed by: Peter Feilen, EMC Engineer Signature: Date: 1/26/15 Report by: Shane D. Rismeyer, EMC Engineer Signature: Date: 1/25/15 This Test Report may not be reproduced, except in full, without written approval of LS Research, LLC. LS Research, LLC Page 2 of 47 Prepared For: Venstar Model Number: THERM-500 Report #: 314318 EUT: ColorTouch Serial Number: Eng Sample LSR Job #: C-2052 Table of Contents 1.0 Summary of Test Report .............................................................................................................. 4 2.0 Test Facilities ............................................................................................................................... 4 3.0 Client Information ........................................................................................................................ 5 3.1 Equipment Under Test (EUT) Information .................................................................................. 5 3.2 Product Description ..................................................................................................................... 5 3.3 Modifications Incorporated In the EUT for Compliance Purposes ............................................. 5 3.4 Deviations & Exclusions from Test Specifications ..................................................................... 5 3.5 Additional Information ................................................................................................................ 5 4.0 Conditions of Test ........................................................................................................................ 6 5.0 Test Equipment ............................................................................................................................ 6 6.0 Conformance Summary ............................................................................................................... 6 Appendix A – Test Equipment ............................................................................................................. 7 Appendix B – Test Data ........................................................................................................................ 8 B.1 – RF Conducted Emissions ........................................................................................................ 8 B.2 – Radiated Emissions ............................................................................................................... 28 Appendix C - Uncertainty Summary .................................................................................................. 46 Appendix D - References .................................................................................................................... 47 LS Research, LLC Page 3 of 47 Prepared For: Venstar Model Number: THERM-500 Report #: 314318 EUT: ColorTouch Serial Number: Eng Sample LSR Job #: C-2052 LS Research, LLC in Review As an EMC Testing Laboratory, our Accreditation and Assessments are recognized through the following: A2LA – American Association for Laboratory Accreditation Accreditation based on ISO/IEC 17025: 2005 with Electrical (EMC) Scope of Accreditation A2LA Certificate Number: 1255.01 Federal Communications Commission (FCC) – USA Listing of 3 Meter Semi-Anechoic Chamber based on Title 47 CFR – Part 2.948 FCC Registration Number: 90756 Industry Canada On file, 3 Meter Semi-Anechoic Chamber based on RSS-212 – Issue 1 File Number: IC 3088-A On file, 3 and 10 Meter OATS based on RSS-212 – Issue 1 File Number: IC 3088 U. S. Conformity Assessment Body (CAB) Validation Validated by the European Commission as a U. S. Competent Body operating under the U. S./EU, Mutual Recognition Agreement (MRA) operating under the European Union Electromagnetic Compatibility –Council Directive 2004/108/EC (formerly 89/336/EEC, Article 10.2). Date of Validation: January 16, 2001 Validated by the European Commission as a U.S. Notified Body operating under the U.S. /EU, Mutual Recognition Agreement (MRA) operating under the European Union Telecommunication Equipment – Council Directive 99/5/EC, Annex V. Date of Validation: November 20, 2002 Notified Body Identification Number: 1243 LS Research, LLC Page 4 of 47 Prepared For: Venstar Model Number: THERM-500 Report #: 314318 EUT: ColorTouch Serial Number: Eng Sample LSR Job #: C-2052 1.0 Summary of Test Report In November-December 2014 the EUT, Color Touch Thermostat, was tested and MEETS the following requirements: FCC and IC Paragraph Test Requirements Compliance (Yes/No) FCC:15.247 (a)(2) IC: RSS 210 A8.2 (a) 6 dB Bandwidth of a Digital Modulation System Yes FCC : 15.247(b) & 1.1310 IC : RSS 210 A8.4 Maximum Output Power Yes FCC:15.247 (d) IC: RSS 210 A8.2 (b) Power Spectral Density of a Digital Modulation System Yes FCC :15.247(d) IC : RSS 210 A8.5 RF Conducted Spurious Emissions at the Transmitter Antenna Terminal Yes FCC : 15.247(c), 15.209 & 15.205 IC : RSS 210 A8.2(b), section 2.2, 2.6 and 2.7 Transmitter Radiated Emissions Yes FCC : 15.109 IC : RSS GEN Receive Mode (Digital Device) Radiated Emissions Yes FCC : 2.1055 (d) Frequency Stability Yes FCC : 15.207 IC : RSS GEN sect. 7.2.2 Power Line Conducted Emissions Measurements Yes 2.0 Test Facilities All testing was performed at: LS Research, LLC W66 N220 Commerce Court Cedarburg, Wisconsin, 53012 USA LS Research, LLC is accredited by A2LA (American Association for Laboratory Accreditation) to the requirements of ISO/IEC 17025, 2005 “General Requirements for the Competence of Calibrat…

Text truncated - open the document above for the full version.

TEST SETUP PHOTOS Company Name Venstar Inc. Model # THERM‐500, THERM‐500B, T7850,T7900, T8850, T8900 FCC ID # MUH‐SKYPORT2 IC # 12547A‐SKYPORT2 Page 1 of 6 TEST SETUP PHOTOS Company Name Venstar Inc. Model # THERM‐500, THERM‐500B, T7850,T7900, T8850, T8900 FCC ID # MUH‐SKYPORT2 IC # 12547A‐SKYPORT2 Page 2 of 6 TEST SETUP PHOTOS Company Name Venstar Inc. Model # THERM‐500, THERM‐500B, T7850,T7900, T8850, T8900 FCC ID # MUH‐SKYPORT2 IC # 12547A‐SKYPORT2 Page 3 of 6 TEST SETUP PHOTOS Company Name Venstar Inc. Model # THERM‐500, THERM‐500B, T7850,T7900, T8850, T8900 FCC ID # MUH‐SKYPORT2 IC # 12547A‐SKYPORT2 Page 4 of 6 TEST SETUP PHOTOS Company Name Venstar Inc. Model # THERM‐500, THERM‐500B, T7850,T7900, T8850, T8900 FCC ID # MUH‐SKYPORT2 IC # 12547A‐SKYPORT2 Page 5 of 6 TEST SETUP PHOTOS Company Name Venstar Inc. Model # THERM‐500, THERM‐500B, T7850,T7900, T8850, T8900 FCC ID # MUH‐SKYPORT2 IC # 12547A‐SKYPORT2 Page 6 of 6