N67-782019-R-FBed Fan with Wireless Remote

782019 Find thousands more great ideas online Merrimack, New Hampshire USA 03054 • 800-846-3000 • Brookstone.com 782019_INS_Bed Fan V2Size:5”Wx4.75”H_Output:100%_Prints:1/1,Blk Chill out. Sleep in. Bed Fan with Wireless Remote CHIll WItH me. Merrimack, New Hampshire USA 03054 • 800-846-3000 • Brookstone.com Cyan Magenta Yellow Black www.croptima.com 782019_INS_Bed Fan V2.indd Sheet: 1 / 8 Date: 2012-4-5 page(s): 16, 1 1 Table of conTenTs Warnings and Cautions......................................................2 Location of Parts and Controls...............................................7 Installing/Replacing Remote Batteries.......................................8 Setting Up Your Bed Fan....................................................9 Operating Your Bed Fan....................................................10 Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Specifications..............................................................12 Warranty ..................................................................13 suppliers other than Brookstone may provide their own warranties to the purchaser, but Brookstone, in so far as permitted by law, provides these products “as is.” This warranty does not apply to: a) damage caused by failure to follow instructions relating to product’s use or the installation of components; b) damage caused by accident, abuse, misuse, fire, floods, earthquake or other external causes; c) damage caused by service performed by anyone who is not a representative of Brookstone; d) accessories used in conjunction with a covered product; e) a product or part that has been modified to alter functionality or capability; f) items intended to be periodically replaced by the purchaser during the normal life of the product including, without limitation, batteries or light bulbs; g) any product sold “as is” including, without limitation, floor demonstration models and refurbished items; or h) a product that is used commercially or for a commercial purpose. BrOOkStONe SHAll NOt Be lIABle FOr INCIDeNtAl Or CONSeQUeNtIAl DAmAGeS reSUltING FrOm tHe USe OF tHIS PrODUCt, Or ArISING OUt OF ANY BreACH OF tHIS WArrANtY. tO tHe eXteNt PermItteD BY APPlICABle lAW, BrOOkStONe DISClAImS ANY AND All StAtUtOrY Or ImPlIeD WArrANtIeS, INClUDING, WItHOUt lImItAtION, WArrANtIeS OF merCHANtABIlItY, FItNeSS FOr A PArtICUlAr PUrPOSe AND WArrANtIeS AGAINSt HIDDeN Or lAteNt DeFeCtS. IF BrOOkStONe CANNOt lAWFUllY DISClAIm StAtUtOrY Or ImPlIeD WArrANtIeS, tHeN tO tHe eXteNt PermItteD BY lAW, All SUCH WArrANtIeS SHAll Be lImIteD IN DUrAtION tO tHe DUrAtION OF tHIS eXPreSS WArrANtY. Some states disallow the exclusion or limitation of incidental or consequential damages or how long an implied warranty lasts, so the above exclusions or limitations may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state. 14 782019_INS_Bed Fan V2Size:5”Wx4.75”H_Output:100%_Prints:1/1,Blk Cyan Magenta Yellow Black www.croptima.com 782019_INS_Bed Fan V2.indd Sheet: 2 / 8 Date: 2012-4-5 page(s): 2, 15 one (1) YeaR lIMITeD WaRRanTY Brookstone ® warrants this product against defects in materials and/or workmanship under normal use for a period of ONE (1) YEAR from the date of purchase by the original purchaser (“Warranty Period”). If a defect arises and a valid claim is received within the Warranty Period, at its option, Brookstone will either 1) repair the defect at no charge, using new or refurbished replacement parts, or 2) replace the product with a new product that is at least functionally equivalent to the original product, or 3) provide a store credit in the amount of the purchase price of the original product. A replacement product or part, including a user-installable part installed in accordance with instructions provided by Brookstone, assumes the remaining warranty of the original product. When a product or part is exchanged, any replacement item becomes your property and the replaced item becomes Brookstone’s property. When a store credit is given, the original product must be returned to Brookstone and becomes Brookstone’s property. Obtaining Service: To obtain warranty service, call Brookstone Limited Warranty Service at 1-800-292-9819. Please be prepared to describe the product that needs service and the nature of the problem. A purchase receipt is required. All repairs and replacements must be authorized in advance. Service options, parts availability and response times will vary. You are responsible for delivery and the cost of delivery of the product or any parts to the authorized service center for replacement, per our instructions. limits and exclusions: Coverage under this Limited Warranty is limited to the United States of America, including the District of Columbia and the U.S. Territories of Guam, Puerto Rico, and the U.S. Virgin Islands. This Limited Warranty applies only to products manufactured for Brookstone that can be identified by the “Brookstone” trademark, trade name, or logo affixed to them or their packaging. The Limited Warranty does not apply to any non-Brookstone products. Manufacturers or 132 782019_INS_Bed Fan V2Size:5”Wx4.75”H_Output:100%_Prints:1/1,Blk caUTIon • TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. THERE ARE NO SERVICEABLE PARTS INSIDE. • TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. The lightning flash with arrow-head symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the unit’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the unit. IMPoRTanT safeTY In…

Text truncated - open the document above for the full version.

1234 A B C D 4321 D C B A Title NumberRevisionSize Letter Date:16-May-2012Sheet of File:F:\My Documents\E1212.ddbDrawn By: E1212 RX BLOCK DIAGRAM 1 1 1 PONY 315MHZ RF MODULE RX-1 MCU U2:46R01C 4MHZ FAN DRIVER POWER SUPPLY AC-DC SWITCHING ANT DC 12V U3: FAN Q 2: 5V REGULATOR It is consisted with four sections: Ant matching net working, UHF downconverter, Resference and control, and OOK demodulator. Also shown in the figure are two capacitors (CTH, CAGC) and one timing component, usually a crystal. With the exception of a supply decoupling capacitor, and antenna impedance matching network, these are the only external components needed to assemble a complete UHF receiver. For optimal performance is highly recommended that the MICRF002 is impedance matched to the antenna, the matching network will add an additional two or three components. Four control inputs are shown in the block diagram: SEL0, SEL1, SWEN, and SHUT. Using these logic inputs, the user can control the operating mode and selectable features of the IC. These inputs are CMOS compatible, and are internally pulled-up. IF Band-pass Filter Roll-off response of the IF Filter is 5th order, while the demodulator data filter exhibits a 2nd order response. There needs a local frequency generator for any super-heterodyne receiver. In this circuit it is based on PLL type circuit inside and a crystal 4.7458 MHz(special for 315 MHz) outside.

Fan: One motor: JD8025HS The other motor: SM8025SH Adaptor:

Technical Description Description Function Component 315 MHz Receive module 1, 315MHz ASK RF receiver and demodulation. 2, RF Module with crystal 4.7458MHz. 3, Receive current 5.7mA & sensitivity -107dbm 315 MHz RX_MOD CPU The function signal decodes U2 Fan Driver The on/off function of fan controls Q2 5V Regulator Change the 12V dc power to 5V dc U3 Power Supply AC-DC Switching power supply Power supply Antenna Used: internal wire antenna It is consisted with four sections: Ant matching net working, UHF downconverter, Resference and control, and OOK demodulator. Also shown in the figure are two capacitors (CTH, CAGC) and one timing component, usually a crystal. With the exception of a supply decoupling capacitor, and antenna impedance matching network, these are the only external components needed to assemble a complete UHF receiver. For optimal performance is highly recommended that the MICRF002 is impedance matched to the antenna, the matching network will add an additional two or three components. Four control inputs are shown in the block diagram: SEL0, SEL1, SWEN, and SHUT. Using these logic inputs, the user can control the operating mode and selectable features of the IC. These inputs are CMOS compatible, and are internally pulled-up. IF Band-pass Filter Roll-off response of the IF Filter is 5th order, while the demodulator data filter exhibits a 2nd order response. There needs a local frequency generator for any super-heterodyne receiver. In this circuit it is based on PLL type circuit inside and a crystal 4.7458 MHz(special for 315 MHz) outside.

1 2 3 4 ABCD 4 3 2 1 D CBA Title Number Revision Size Letter Date: 15-May-2012 Sheet of File: F:\My Documents\E1212.ddb Drawn By: RX PART 1 PONY 1 1 VDD 1 PA6 2 PA5 3 PA7 4 PA2 5 PA1 6 PA0 7 VSS 8 U2 46R01C DAT 1 GND 2 VDD 3 315MHZ RX_MOD D11N4007 Vin 1 GND 2 Vout 3 U3 LM7805 + C3 220UF 16V C4 0.1UF R6 10K R5 150R R7 1K E1212 +12V DC +5V DC Q24410 FAN1 12V DC FAN2 12V DC D3 1N4007 C6 0.1UF ANT Fosc=4MHZ 123 J1
      
             
  !!!!"! #  $% $&

' (! )*+ )*+ ,-
- .
/-  .
01 . *21 

* 3
*
 4
'0*/ ,- 51 0* 6
 
 ,
5 5 *
* 5 
0
- .'% 76
+#  +#    + * + 3  1 0  / + 2 5
 18

9:7
 ;
 76

 7#5
* 97
3 /

Intertek Testing Services Shenzhen Ltd. Kejiyuan Branch 6F, D Block, Huahan Building, Langshan Road, Nanshan District, Shenzhen, P. R. China Tel: (86 755) 8601 6288 Fax: (86 755) 8601 6751 Website: www.china.intertek-etlsemko.com 31 July, 2012 Chung Mei Industries Limited 11th Floor Chung Mei Centre, 15B Hing Yip Street , Kwun Tong Kowloon Hong Kong Dear Mr. Jing Hua Liu, Enclosed you will find your file copy of a Part 15 Certification (FCC ID: N67-782019-R-F). For your reference, TCB will normally take another 5 days for reviewing the report. Approval will then be granted when no query is sorted. Please contact me if you have any questions regarding the enclosed material. Sincerely, Shawn Xing Enclosure • The test results reported in this test report shall refer only to the sample actually tested and shall not refer or be deemed to refer to bulk from which such a sample may be said to have been obtained. • This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to copy or distribute this report. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results referenced from this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. • For Terms And Conditions of the services, it can be provided upon request. • The evaluation data of the report will be kept for 3 years from the date of issuance. TRF no.: FCC 15C_RX_b FCC ID: N67-782019-R-F Intertek Testing Services Shenzhen Ltd. Kejiyuan Branch 6F, D Block, Huahan Building, Langshan Road, Nanshan District, Shenzhen, P. R. China Tel: (86 755) 8601 6288 Fax: (86 755) 8601 6751 Website: www.china.intertek-etlsemko.com Chung Mei Industries Limited Application For Certification (FCC ID: N67-782019-R-F) Superheterodyne Receiver Sample Description: Bed Fan with Wireless Remote Model: SKU 782019, E1212 SZ12060224-1 Billy Li 31 July, 2012 INTERTEK TESTING SERVICES TRF no.: FCC 15C_RX_b FCC ID: N67-782019-R-F і LIST OF EXHIBITS INTRODUCTION EXHIBIT 1: General Description EXHIBIT 2: System Test Configuration EXHIBIT 3: Emission Results EXHIBIT 4: Equipment Photographs EXHIBIT 5: Product Labelling EXHIBIT 6: Technical Specifications EXHIBIT 7: Instruction Manual EXHIBIT 8: Miscellaneous Information EXHIBIT 9: Test Equipment List INTERTEK TESTING SERVICES TRF no.: FCC 15C_RX_b FCC ID: N67-782019-R-F ii MEASUREMENT/TECHNICAL REPORT Chung Mei Industries Limited - MODEL: SKU 782019, E1212 FCC ID: N67-782019-R-F This report concerns (check one:) Original Grant X Class II Change _____ Equipment Type: CYY – Communications Receiver used w/Pt 15 Transmitter Deferred grant requested per 47 CFR 0.457(d)(1)(ii)? Yes No X If yes, defer until: date Company Name agrees to notify the Commission by: date of the intended date of announcement of the product so that the grant can be issued on that date. Transition Rules Request per 15.37? Yes No X If no, assumed Part 15, Subpart B for unintentional radiator - the new 47 CFR [10-1-10 Edition] provision. Report prepared by: Shawn Xing Intertek Testing Services Shenzhen Ltd. Kejiyuan Branch 6/F, Block D, HuaHan Building, Longshan Road, Nanshan District, Shenzhen, China. Phone: (86 755) 86016288 Fax: (86 755) 86016751 INTERTEK TESTING SERVICES TRF no.: FCC 15C_RX_b FCC ID: N67-782019-R-F iii Table of Contents 1.0 General Description ........................................................................................ 2 1.1 Product Description ........................................................................................... 2 1.2 Related Submittal(s) Grants............................................................................... 2 1.3 Test Methodology.............................................................................................. 3 1.4 Test Facility ....................................................................................................... 3 2.0 System Test Configuration ............................................................................. 5 2.1 Justification ....................................................................................................... 5 2.2 EUT Exercising Software................................................................................... 5 2.3 Special Accessories .......................................................................................... 5 2.4 Equipment Modification ..................................................................................... 6 2.5 Measurement Uncertainty.................................................................................. 6 2.6 Support Equipment List and Description ............................................................ 6 3.0 Emission Results ............................................................................................ 8 3.1 Field Strength Calculation.................................................................................. 9 3.2 Radiated Emission Configuration Photograph.................................................. 10 3.3 Radiated Emission Data .................................................................................. 11 3.4 Conducted Emission Data.......................................................................13 4.0 Equipment Photographs ............................................................................... 18 5.0 Product Labelling .............................................................…

Text truncated - open the document above for the full version.