N6YUT-1100RCar Alarm

TWO WAY CARF-1100R (USER’S MANUAL) UTEL CO.,LTD. N6YUT-1100R UTEL CO.,LTD CARF-1100R THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS : (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. Caution : Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Please check the followings before use. 1. This manual explained mainly the CARF-1100 model functions. 2. Once the engine( for manual transmission ) is started (by the key or remote controller), the engine does not stop even if the key is pulled out from the key box. After the user gets off the car, the doors will be locked and the engine will stop. (confirmation is required) 3. When the program is completed, the program jumper (cable of 2 PIN connector) must be cut. If the wire is still connected, the remote controller does not work. 4. After reading this manual, please confirm function of this product (whether they correspond with directions written on this manual) If any problem is founded, please contact our agency or company We do not have any reasonabilities for wrong operation coming from SET UP/SET UP program errors. CAUTION: This product must be installed by a technician who is instructed by UTEL(or agency)and arbitrary installation is prohibited. For the efficient use : 1. Codeless communication devices can be interrupted by near electronic waves and the territorial characteristics will have an influence on the communication distance. 2. For the efficient management of the car equipped with this product, please check the communication distance and if it is necessary the user can extend the distance by using the antenna. 1 THE TABLE OF CONTENTS 1. Components 2. Function of CARF-1100 1) CARF - 1100 2) Function of the buttons 3. Usage of CARF-1100 1) Function of button I (1)Arm /Disarm (Door lock/Unlock) (2)Valet ON/OFF 2) Function of button II (1)Auto transmission car (2)Manual transmission car 3) Function of button III (1)Opening the trunk (2)Knock, shock sensor ON/OFF 4) Function of button IV (1) Confirmation of the car condition (2) Panic function(emergency alarm) 5) Knock sensor 6) Auto re-arm 7) Enable/disable chirp 8) Operation of A/C/Heater 9) Cancellation of the alert tone 10) Low battery alarm 11) Change of arm delay time 4. Installation 1) Check list of carf series. 2) Connection and color code of the main harness ass'y 3) How to find wires(color and functions) 4) Wiring diagram 5) Program method 5. Warranty sheet 2 1. Components REMOTE(CARF-1100R) BASE MODULE(CARF-1100B) MAIN SIREN SHOCK SENSOR CABLE (4,6,8,10 pin connector)  3  2.Function of CARF-1100 1) CARF-1100 REMOTE CONTROLLED ENGINE START EMERGENCY LIGHTING AIR CONDITIONER AND HEATER OPERATION DOOR LOCK/UNLOCK VALET FUNCTION AUTO RE-ARM PANIC FUNCTION(EMERGENCY ALARM) CONFIRMATION OF THE ALARM TRUNK OPEN KNOCK SENSOR SHOCK SENSOR(IMPACT SENSOR) DOOR OPEN ALARM CONFIRMATION OF THE CAR CONDITION CONFIRMATION OF THE COMMUNICATION DISTANCE ENABLE AND DISABLE CHIRP 2) FUNCTION OF THE BUTTONS Short : press the button A beep accompanied by a green blink will occur once (remote controller) long : press the button for more than 2 seconds. The beep accompanied by a green blink will occur twice.  4   5  3. Usage of CARF-1100 Button Button press Door (CONDITION) Function CONFIRMATION SOUND (REMOTE CONTROLLER) SHORT CLOSED DOOR LOCK DOOR UNLOCK 1 BEEP, 1 GREEN LED 2.BEEPS, 2.GREEN LEDS  LONG CLOSED VALET ON VALET OFF 1 DUAL-BEEP, 1 GREEN LED 1 BEEP-HIGH-LOW, 1.GREEN LED SHORT CLOSED (LOCKED) REMOTE ENGINE START ENGINE STOP 1 CRIKET SOUND 1 GREEN LED 2 CRIKET SOUNDS 2GREENLEDS CLOSED ARM DELAY TIME4,10SEC ARM DELAY TIME AFTER 2SEC 4SEC →10SEC, 10SEC→4SEC  LONG OPENED CHIRP ON/OFF SOUND ON/OFF AFTER 2 SEC SHORT CLOSED OPENED TRUNK OPEN 2 DUAL-BEEPS 2GREENLEDS  LONG CLOSED (UNLOCKED) KNOCK,IMPACT SENSOR 1 BEEP 1GREENLED SHORT CLOSED OPENED CHECKING CARCONDITION DEPENDS ON FUNCTION  LONG CLOSED OPENED PANIC ON 1 BEEP 1 GREEN LED AFTER 2 SEC Confirmation sound will be heard from the remote controller after each button is pressed( A beep with a green LED blink ) When it occurs, please remove your finger from the buttons. (If you keep pressing the button, This set may operate another function) Example) To lock the door, press "button"of the remote controller. When the button is pressed. The beep accompanied by a green blink will occur once on the remote controller, then the same thing will happen to the car (The turn signal with a chirp will blink once.) This means the door is locked, After a little while the car will send the call back signal to the remote controller.(The beep with green LED blink) CALLBACK ? - When the button of the remote controller is pressed and the command is performed, this signal will be sent to the remote controller from the car to confirm that the command has been recognized.  6  1)Function of the button  (1) Arm/Disarm(Door lock/Unlock) 1. When the "button " is pressed, the beep will sound and the green LED will blink once each on the remote controller. 2.The chirp accompanied by the turn signal blink will occur at the same time on the car, then the doors will be locked and the callback signal will be sent from the car. 3.When the "button" is pressed once again, another beep and green LED blink will occur on the remote controller, but with the car, the chirp accompanied by the turn signal blink will occur twice),then the doors will be unlocked.(Callback signal will be sent once again-two beeps with two LED blink) 4. If you try to open the locked door with the key(not with the remote controller)or just by the force, the alarm will start and both the sound and yellow LED blink will arise 8 times on the remote controller. Right at t…

Text truncated - open the document above for the full version.

CARF-1100R BLOCK DIAGRAM BFR92A 1st MIXER BFR92A FILTER 1st IF AMP 2nd MIXER (TA31142) 10.7MHz KTC3879Y R/TX EXCHANGE 2N3904S2N3906S 1st LOCAL OSC 2nd LOCAL OSC FILTER CH.CRYSTAL 10.245MHz 455KHz BFR92A FREQUENCY MULTIPLIER BFR92A OSC & FREQUENCY MULTIPLIER CH.CRYSTAL & BFR92A FREQUENCY MODULATION MMBV109 RX DATATX DATA CPUPIC16C621 POWER UP CIRCUIT RH5RI301B1.5V TO 3V SW1~4

EXTERNAL TOP SIDE EXTERNAL BOTTOM SIDE FCC ID : N6YUT-1100R FCC ID : N6YUT-1100R

PROPOSED FCC ID. LABEL AND MARKING BOTTOM SIDE

INTERNAL TOP SIDE INTERNAL BOTTOM SIDE FCC ID : N6YUT-1100R INTERNAL TOP SIDE INTERNAL BOTTOM SIDE FCC ID : N6YUT-1100R FCC ID : N6YUT-1100R FCC ID : N6YUT-1100R

CIRCUIT DESCRIPTIONS ON THE CARF-1100R CARF-1100R has two parts. The first part is RX board, and the second is TX board. Also, TX board has power circuit. Followings are descriptions on circuits. 1. RX BOARD The power of this board is supplied by the D/D converter on the TX board and this board demodulates the RF signal from transmitter. A. FRONTEND CIRCUIT The received signal through the antenna is amplified by Q1,Q2 ( BFR92A ), and the amplified signal is sent to the 1st mixer. B. 1st LOCAL OSCILLATOR The oscillated and multiplied signal by X1 ( CH.CRYSTAL ), Q7 and Q8 ( BFR92A ) is sent to the 1st mixer. C. FILTER ( 10.7MHz ) The down converted signal through the 1st mixer is filtered by filter ( 10.7MHz ). D. 1st IF AMPLIFIER The IF signal is amplified by Q4 ( KTC3879Y ), and sent to the 2nd mixer. E. 2nd LOCAL OSCILLATOR The 2nd local signal by U1 ( TA31142 ) and X2 ( 10.245MHz ) are sent to the 2nd mixer. F. 2nd MIXER The 2nd mixer which makes the signal of 455KHz is located inside of U1 ( TA31142 ). G. CPU The recovered data through the U1 is supplied to the U2 ( PIC16C621 ) and analyzed by U2. 2. TX BOARD This circuit makes a modulated RF signal and sends it to the receiver by air. A. POWER CIRCUIT The CARF-1100R uses the 1.5V AAA battery. The power supply of 1.5V is applied to the U3,U4 ( RH5RI301B ) and boosted up to 3.0V. B. FREQUENCY MODULATION The ID data made by the U2 is supplied to the D2 ( MMBV109 ) of the oscillator. C. OSCILLATOR & FREQUENCY MULTIPLIER The oscillated signal by X4 ( CH.CRYSTAL ) is multiplied by Q9 ( BFR92A ) and fed to the Q10. D. FREQUENCY MULTIPLIER The multiplied signal by Q10 ( BFR92A ) are sent to the amplifier part. E. HIGH FREQUENCY AMPLIFIER The multiplied signal by Q10 ( BFR92A ) is sent to the antenna via RX/TX-exchange circuit.

KTL Korea Testing Laboratory Page 1 of 15 TEST REPORT This test report only responds to the tested sample and shall not be reproduced except in full without written approval of the the Korea Testing Laboratory. Tested and reported by Reviewed by Soun-Kweon Seol , Senior Engineer Seok-Jin Kim , EMC Team Leader KOREA TESTING LABORATORY FG101-01-02-00 222-13, Guro-Dong Guro-Gu Seoul Korea 152-053 http://www.ktl.re.kr Ref. Report No. 99-341-040-1 Name and address of the applicant Utel Co., Ltd. 1662-13, Daechang B/D 2F, Bongchun 7-dong, Kwamak-ku, Seoul, Korea 151-057 Standard / Test regulation FCC Part 15, Subpart C Test result Pass Incoming date : July 22, 1999 Test item(s) ; Security/Remote Control Transmitter (Car Alarm) Model/type ref. ; CARF-1100R Manufacturer ; Utel Co., Ltd. Additional information ; -Required Authorization :Certification -FCC ID. : N6YUT-1100R - N o t e : Test report(verification) on receiver portion of this unit is issued on Ref.Report No. 99-341-040-2. Test date : July 30, 1999 Issue date : August 4, 1999 Ref. Report No. 99 - 341 – 040-1 Page 2 of 15 TABLE OF CONTENTS . GENERAL INFORMATION ................................................................................................................... 3 1. Grantee Name and Mailing Address 2. Manufacturer's Name and Mailing Address 3. Equipment Descriptions 4. Rules and Regulations 5. Measuring Procedure 6. Place of Measurement 7. Date of Measurement . GENERAL REQUIREMENTS OF THE EUT ...................................................................................... 5 1. Labelling Requirement (Section 15.19) 2. Information to User (Sections 15.21) 3. Special Accessories (Section 15.27) 4. Compliant Conditions (Section 15.231) 5. Modification of the Equipment Under Test . INPUT POWER MEASUREMENT (Section 15.31)............................................................................. 6 . RADIATED EMISSION MEASUREMENT (Section 15.231)............................................................ 7-13 1. Test Procedure 2. Photograph for the worst case configuration 3. Sample Calculation 4. Measurement Data 5. Reference Data . OCCUPIED BANDWIDTH MEASUREMENT (Section.15.231)...................................................... 14 . TEST EQUIPMENTS USED FOR FCC COMPLIANCE TESTING................................................ 15 Ref. Report No. 99 - 341 – 040-1 Page 3 of 15 . GENERAL INFORMATION 1. Grantee Name and : Utel Co., Ltd. Mailing Address 1662-13, Daechang B/D 2F, Bongchun 7-dong, Kwamak-ku, Seoul, Korea 151-057 2. Manufacturer's Name and : Utel Co., Ltd. Mailing Address 1662-13, Daechang B/D 2F, Bongchun 7-dong, Kwamak-ku, Seoul, Korea 151-057 3. Equipment Descriptions 3.1 Operating Frequency : 447.6375MHz 3.2 Type of Emission : FM Pulse Code Signal 3.3 Power Supply : DC 1.5V ( Battery) 3.4 Additional Information; - Oscillator used : Crystal(49.7375MHz) X 9 = 447.6375MHz - Frequency Multiplier used : BFR92A 4. Rules and Regulations : FCC Part 15, Subpart C 5. Measuring Procedure : ANSI C63.4-1992 6. Place of Measurement : Absorber-lined room(3-Meter) of KAITECH 7. Date of Measurement 6.1 Conducted Emission : Not Applicable 6.2 Radiated Emission : July 30, 1999 Ref. Report No. 99 - 341 – 040-1 Page 4 of 15 . GENERAL REQUIREMENTS OF THE EUT 1. Labelling Requirement (Section 15.19) 1.1 Location on Enclosure : Manual for Installation and Operating Instruction 1.2 How Applied : Printing 2. Information to User (Section 15.21) The following or similar statements were provided in the manual for user instruction. Please refer page 2 of the attached manual for details. 3. Special Accessories (Section 15.27) 3.1 Were the special Accessories provided? [ ] yes, [ x ] no 3.2 If yes, details for the special accessories are as follows : 3.3 If yes, were the appropriate instructions provided on the first page of the text concerned with the device? [ ] yes, [ ] no 3.4 Are these accessories provided of the type which can be readily obtained from multiple retail outlets? [ ] yes, [ ] no And therefore does the manual specify what additional components or accessories are required to used in order to comply with the Rules? [ ] yes, [ ] no This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION : Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Ref. Report No. 99 - 341 – 040-1 Page 5 of 15 4. Compliant Conditions (Section 15.231) 4.1 Was the EUT used for continuous transmissions, such as voice or video, and data transmission ? [ ] yes, [ x ] no 4.2 Was the EUT manually operated ? [ x ] yes, [ ] no If yes, did the EUT employ a switch that would automatically deactivate the transmitter within not more than 5 seconds of being released ? [ x ] yes, [ ] no 4.3 Was the EUT automatically activated ? [ ] yes, [ x ] no If yes, did the EUT cease transmission within 5 seconds after deactivation ? [ ] yes, [ ] no 4.4 Was the EUT used for periodic transmissions at regular predetermined intervals ? [ ] yes, [ x ] no 5. Modification of the Equipment Under Test [ x ] Any modifications were not made to the EUT during the testing since the test results were found of be complied with the FCC Rules with the EUT in the as received condition. [ ] Modification(s) was(were) made to the EUT in order to make it meet FCC Rules since it had shown non- compliance for some test items in the course of our testing. - Status of non-compliance : - Details of Modifications : Ref. Report No. 99 - 341 – 040-1 Page 6 of 15 . INPUT POWER MEASUREMENT (Section 15.31) INPUT POWER 14.17 mW Note : 1. Input Power : P ove = (P p x D) pulse + P D Where, P p : Input Peak Power (= V x I p ) P D : Input …

Text truncated - open the document above for the full version.

TEST SETUP PHOTOS RADIATED EMISSION