NHP-TG1502Astro Telepresence Adapter

2x2 11n USB dongle User’s Guide i Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Operations in the 5.15-5.25GHz band are restricted to indoor usage only. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user. This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna, As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: NHP- TG1502”. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. For Taiwan 警語 警語警語 警語： ：： ： ii 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之 特性及功能。 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方 得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫 療用電波輻射性電機設備之干擾。 Europe – EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC: EN60950-1: 2009 Safety of Information Technology Equipment EN 62311: 2008 Assessment of electronic and electrical equipment related to human exposure restrictions for electromagnetic fields (0 Hz – 300GHz) EN 300 328 V1.7.1 (2006-10) Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband transmission systems; Data transmission equipment operating in the 2,4 GHz ISM band and using wide band modulation techniques; Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive EN 301 489-1 V1.8.1 (2008-04) Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements EN 301 489-17 V2.1.1 (2009-05) Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 17: Specific conditions for 2,4 GHz wideband transmission systems and 5 GHz high performance RLAN equipment This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries, except in France and Italy where restrictive use applies. In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio links and/or for supplying public access to telecommunications and/or network services. This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 – 2483.5 MHz. For detailed information the …

Text truncated - open the document above for the full version.

FCC ID: NHP-TG1502 Report No.: RF110804C16 Modular Approval Request Letter Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch September 9, 2011 Dear Application Examiner, CAMEO COMMUNICATIONS, INC., It’s a WLAN module, FCC ID: NHP-TG1502 would like to have your authorization as a modular device. The requirements of section 15.212 of FCC rules have been met and shown on the following statements. 1. “The modular transmitter must have its own RF shielding.”: The radio portion of this module has been shielded, please see exhibition External Photo. 2. “The modular transmitter must have buffered modulation/data inputs.” The EUT has buffered data inputs, it is integrated in chip RT3572. 3. “The modular transmitter must have its own power supply regulation.” The part number of this regulator is CAT7311. 4. “The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(C).” The EUT meets the FCC antenna requirements. The spurious emission, unique antenna connector and photo of antennas are shown in the test report. 5. “The modular transmitter must be tested in a stand-alone configuration” The EUT was tested in a stand-alone configuration via extender. Please see section Photographs of Test Configuration in the test report, the EUT was plugged in this extender. 6. “The modular transmitter must be labeled with its own FCC ID number.” Please see exhibition Label Sample for the FCC ID of this module. And also in the exhibition Users Manual, there are instructions give to the OEM on how to label the end product. FCC ID: NHP-TG1502 Report No.: RF110804C16 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.” The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are given in the Users Manual. 8. “The modular transmitter must comply with any applicable RF exposure requirements.” The EUT is compliant with all applicable RF exposure requirements. RF Exposure is addressed in the RF exposure exhibition. Please contact me if you have any further questions. Thanks for your attention. Best Regards, signature Gary Chang Assistant Manager Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch

Page 1 CONSTRUCTION PHOTOS OF EUT

Label Location

'( )*+, )*-. /0&1 234 564 78 Approval *Note* Av:!" THOMSON Jasmine 2011/08/30 TG1502 (FCC) Antony SN Label MAC Label 34.00 mm 6.00 mm 40.00 mm 10.00 mm 1. Label size: 34x6mm 2. Barcode type: code39 3. The height of barcode2mm 4. Font: Arial 5. The height of font 1 5mm ! ! . *Note* 1. Label size: 40x10mm 2. Barcode type: code39 3. The height of barcode2mm 4. Font: Arial 5. The height of font 1 5mm 6. Cameo MAC ! ! . SN: YYWWVVAXXXXX MAC: XXXXXXXXXXXX 7332TG1502*0AAv 6.CAMEO Generic Serial Number: (1) YY: Production Year (2) WW: Production Week (3) VV: Product Version, Ex.Cameo PN:, VV=A1 (4) A : Plant Code , Ex. China=> GNT : remark:we will start with D00001 to D99999, if we produce more than 100,000pcs a week, we will need to use E (5) XXXXX:, YYWWVVAXXXXX D E F Decimalism 00001 ~ 99999 " " 7332TG1502*0AA1 FCC ID: NHP-TG1502

Page 2 Page 3

FCC ID: NHP-TG1502 Report No.: RF110804C16 Operational Description This device is a USB Adapter, which operates in both 2.4GHz and 5GHz bands; the maximum data rate could be up to 300Mbps which OFDM technique. If the signal to noise radio is too poor which could not support 300Mbps, the 11Mbps data rate with DSSS technique will be applied. The transmitter of the EUT is powered by 5Vdc from host equipment. The antenna is PIFA with UFL antenna connector. For more detailed instruction, please take a look at the user’s manual. FCC 15.407(c) states: The device shall automatically discontinue transmission in case of either absence of information to transmit or operational failure. These provisions are not intended to preclude the transmission of control or signaling information or the use of repetitive codes used by certain digital technologies to complete frame or burst intervals. Applicants shall include in their application for equipment authorization a description of how this requirement is met” Data transmission is always initiated by software, which is then pass down through the MAC, through the digital and analog baseband, and finally to the RF chip. Several special packets (ACKs, CTS, PSPoll, etc...) are initiated by the MAC. There are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only while one of the aforementioned packets are being transmitted.

Report No.: SA110804C16 Report Format Version 4.0.0 1 RF EXPOSURE REPORT REPORT NO.: SA110804C16 MODEL NO.: TG-1502 FCC ID: NHP-TG1502 APPLICANT: CAMEO COMMUNICATIONS, INC. ADDRESS: No. 42, Sec. 6, Mincyuan E. Rd., Neihu District, Taipei City 114, Taiwan ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Tsuen, Lin Kou Hsiang, Taipei Hsien 244, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 6 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced, except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval or endorsement by any government agency. The test results in the report only apply to the tested sample. Report No.: SA110804C16 Report Format Version 4.0.0 2 TABLE OF CONTENTS RELEASE CONTROL RECORD ............................................................................................. 3 1. CERTIFICATION .......................................................................................................... 4 2. RF EXPOSURE............................................................................................................ 5 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE)...................................... 5 2.2 MPE CALCULATION FORMULA ................................................................................. 5 2.3 CLASSIFICATION ........................................................................................................ 5 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER............................... 6 Report No.: SA110804C16 Report Format Version 4.0.0 3 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED Original release NA Sep. 02, 2011 Report No.: SA110804C16 Report Format Version 4.0.0 4 1. CERTIFICATION PRODUCT: Astro Telepresence Adapter MODEL: TG-1502 BRAND: Technicolor APPLICANT: CAMEO COMMUNICATIONS, INC. TESTED: Aug. 05 ~ Aug. 29, 2011 TEST SAMPLE: ENGINEERING SAMPLE STANDARDS: FCC Part 2 (Section 2.1091) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 The above equipment (Model: TG-1502) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE:Sep. 02, 2011 Pettie Chen / Specialist APPROVED BY : , DATE:Sep. 02, 2011 Gary Chang / Technical Manager Report No.: SA110804C16 Report Format Version 4.0.0 5 2. RF EXPOSURE 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY (mW/cm 2 ) AVERAGE TIME (minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 2.2 MPE CALCULATION FORMULA Pd = (Pout*G) / (4*pi*r2) where Pd = power density in mW/cm2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm 2.3 CLASSIFICATION The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. Report No.: SA110804C16 Report Format Version 4.0.0 6 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER FREQUENCY BAND (MHz) MAX POWER (dBm) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/cm 2 ) LIMIT (mW/cm 2 ) 2412-2462 28.3 0 20 0.133 1 5180-5240 16.6 2 20 0.014 1 5745-5825 25.4 2 20 0.108 1 ---END---

Report No.: RF110804C16 1 Report Format Version 4.0.0 FCC TEST REPORT (15.247) REPORT NO.: RF110804C16 MODEL NO.: TG-1502 FCC ID: NHP-TG1502 RECEIVED: Aug. 04, 2011 TESTED: Aug. 05 ~ Aug. 29, 2011 ISSUED: Sep. 02, 2011 APPLICANT: CAMEO COMMUNICATIONS, INC. ADDRESS: No. 42, Sec. 6, Mincyuan E. Rd., Neihu District, Taipei City 114, Taiwan ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Tsuen, Lin Kou Hsiang, Taipei Hsien 244, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 137 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product, certification, approval or endorsement by TAF or any government agency. The test results in the report only apply to the tested sample. Report No.: RF110804C16 2 Report Format Version 4.0.0 TABLE OF CONTENTS RELEASE CONTROL RECORD......................................................................................... 5 1. CERTIFICATION...................................................................................................... 6 2. SUMMARY OF TEST RESULTS ............................................................................. 7 2.1 MEASUREMENT UNCERTAINTY .......................................................................... 7 3. GENERAL INFORMATION ...................................................................................... 8 3.1 GENERAL DESCRIPTION OF EUT........................................................................ 8 3.2 DESCRIPTION OF TEST MODES........................................................................ 10 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST ................................................... 11 3.2.2 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ........................ 12 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS ....................................... 16 3.4 DESCRIPTION OF SUPPORT UNITS .................................................................. 16 4. TEST TYPES AND RESULTS (FOR 2.4GHz BAND)............................................ 17 4.1 RADIATED EMISSION MEASUREMENT ............................................................. 17 4.1.1 LIMITS OF RADIATED EMISSION MEASUREMENT........................................... 17 4.1.2 TEST INSTRUMENTS .......................................................................................... 18 4.1.3 TEST PROCEDURES ........................................................................................... 19 4.1.4 DEVIATION FROM TEST STANDARD ................................................................. 19 4.1.5 TEST SETUP ........................................................................................................ 20 4.1.6 EUT OPERATING CONDITIONS .......................................................................... 20 4.1.7 TEST RESULTS .................................................................................................... 21 4.2 CONDUCTED EMISSION MEASUREMENT ........................................................ 34 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT...................................... 34 4.2.2 TEST INSTRUMENTS .......................................................................................... 34 4.2.3 TEST PROCEDURES ........................................................................................... 35 4.2.4 DEVIATION FROM TEST STANDARD ................................................................. 35 4.2.5 TEST SETUP ........................................................................................................ 36 4.2.6 EUT OPERATING CONDITIONS .......................................................................... 36 4.2.7 TEST RESULTS .................................................................................................... 37 4.3 6dB BANDWIDTH MEASUREMENT .................................................................... 39 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT .................................................. 39 4.3.2 TEST INSTRUMENTS .......................................................................................... 39 4.3.3 TEST PROCEDURE ............................................................................................. 39 4.3.4 DEVIATION FROM TEST STANDARD ................................................................. 39 4.3.5 TEST SETUP ........................................................................................................ 40 4.3.6 EUT OPERATING CONDITIONS .......................................................................... 40 4.3.7 TEST RESULTS .................................................................................................... 41 4.4 MAXIMUM OUTPUT POWER ............................................................................... 45 Report No.: RF110804C16 3 Report Format Version 4.0.0 4.4.1 LIMITS OF MAXIMUM OUTPUT POWER MEASUREMENT ............................... 45 4.4.2 INSTRUMENTS..................................................................................................... 45 4.4.3 TEST PROCEDURES ........................................................................................... 45 4.4.4 DEVIATION FROM TEST STANDARD ................................................................. 46 4.4.5 TEST SETUP ........................................................................................................ 46 4.4.6 EUT OPERATING CONDITIONS .......................................................................... 46 4.4.7 TEST RESULTS .................................................................................................... 47 4.5 POWER SPECTRAL DENSITY MEASUREMENT...........................…

Text truncated - open the document above for the full version.

Report No.: RF110804C16-1 1 Report Format Version 4.0.0 FCC TEST REPORT (15.407) REPORT NO.: RF110804C16-1 MODEL NO.: TG-1502 FCC ID: NHP-TG1502 RECEIVED: Aug. 04, 2011 TESTED: Aug. 05 ~ Aug. 29, 2011 ISSUED: Sep. 02, 2011 APPLICANT: CAMEO COMMUNICATIONS, INC. ADDRESS: No. 42, Sec. 6, Mincyuan E. Rd., Neihu District, Taipei City 114, Taiwan ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Tsuen, Lin Kou Hsiang, Taipei Hsien 244, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 78 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product, certification, approval or endorsement by TAF or any government agency. The test results in the report only apply to the tested sample. Report No.: RF110804C16-1 2 Report Format Version 4.0.0 TABLE OF CONTENTS RELEASE CONTROL RECORD......................................................................................... 4 1. CERTIFICATION...................................................................................................... 5 2. SUMMARY OF TEST RESULTS ............................................................................. 6 2.1 MEASUREMENT UNCERTAINTY .......................................................................... 6 3. GENERAL INFORMATION ...................................................................................... 7 3.1 GENERAL DESCRIPTION OF EUT........................................................................ 7 3.2 DESCRIPTION OF TEST MODES.......................................................................... 8 3.2.1 CONFIGURATION OF SYSTEM UNDER TEST ..................................................... 8 3.2.2 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL .......................... 9 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS ....................................... 11 3.4 DESCRIPTION OF SUPPORT UNITS .................................................................. 11 4. TEST TYPES AND RESULTS ............................................................................... 12 4.1 RADIATED EMISSION MEASUREMENT ............................................................. 12 4.1.1 LIMITS OF RADIATED EMISSION MEASUREMENT........................................... 12 4.1.2 LIMITS OF UNWANTED EMISSION OUT OF THE RESTRICTED BANDS ......... 12 4.1.3 TEST INSTRUMENTS .......................................................................................... 13 4.1.4 TEST PROCEDURES ........................................................................................... 14 4.1.5 DEVIATION FROM TEST STANDARD ................................................................. 14 4.1.6 TEST SETUP ........................................................................................................ 15 4.1.7 EUT OPERATING CONDITION ............................................................................ 15 4.1.8 TEST RESULTS .................................................................................................... 16 4.2 CONDUCTED EMISSION MEASUREMENT ........................................................ 25 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT...................................... 25 4.2.2 TEST INSTRUMENTS .......................................................................................... 25 4.2.3 TEST PROCEDURES ........................................................................................... 26 4.2.4 DEVIATION FROM TEST STANDARD ................................................................. 26 4.2.5 TEST SETUP ........................................................................................................ 27 4.2.6 EUT OPERATING CONDITIONS .......................................................................... 27 4.2.7 TEST RESULTS .................................................................................................... 28 4.3 MAXIMUM CONDUCTED OUTPUT POWER MEASUREMENT .......................... 30 4.3.1 LIMITS OF MAXIMUM CONDUCTED OUTPUT POWER MEASUREMENT ....... 30 4.3.2 TEST INSTRUMENTS .......................................................................................... 30 4.3.3 TEST PROCEDURE ............................................................................................. 31 4.3.4 DEVIATION FROM TEST STANDARD ................................................................. 31 4.3.5 TEST SETUP ........................................................................................................ 31 4.3.6 EUT OPERATING CONDITIONS .......................................................................... 31 4.3.7 TEST RESULTS .................................................................................................... 32 4.4 PEAK POWER EXCURSION MEASUREMENT ................................................... 36 4.4.1 LIMITS OF PEAK POWER EXCURSION MEASUREMENT................................. 36 4.4.2 TEST INSTRUMENTS .......................................................................................... 36 4.4.3 TEST PROCEDURE ............................................................................................. 36 4.4.4 DEVIATION FROM TEST STANDARD ................................................................. 37 4.4.5 TEST SETUP ........................................................................................................ 37 4.4.6 EUT OPERATING CONDITIONS .......................................................................... 37 4.4.7 TEST RESULTS .................................................................................................... 38 4.5 PEAK POWER SPECTRAL DENSITY MEASUREMENT ..................................... 44 4.…

Text truncated - open the document above for the full version.