NI3-2511SR2-Port Wireless Router

Senao 2-Port Switch Wireless Router User Guide Before operating the unit, please read this manual thoroughly, and retain it for future reference. Model No. SL-2511SR Copyright The contents of this publication may not be reproduced in any part or as a whole, stored, transcribed in an information retrieval system, translated into any language, or transmitted in any form or by any means, mechanical, magnetic, electronic, optical, photocopying, manual, or otherwise, without the prior written permission. Trademarks All product, company, brand names are trademarks or registered trademarks of their respective companies. They are used for identification purpose only. Specifications are subject to be changed without prior notice. -1- FCC Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against radio interference in a commercial environment. This equipment can generate, use and radiate radio frequency energy and, if not installed and used in accordance with the instructions in this manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause interference, in which case the user, at his own expense, will be required to take whatever measures are necessary to correct the interference. CE Declaration of Conformity This equipment complies with the requirements relating to electromagnetic compatibility, EN 55022/A1 Class B, and EN 50082-1. This meets the essential protection requirements of the European Council Directive 89/336/EEC on the approximation of the laws of the member states relation to electromagnetic compatibility. -2- Table of Contents Chapter 1 Introduction...............................................................................4 Functions and Features .........................................................................4 1.2 Packing List ....................................................................................5 Chapter 2 Hardware Installation................................................................6 2.1 Panel Layout...................................................................................6 2.2 Procedure for Hardware Installation..............................................8 Chapter 3 Configuring Wireless Access Point.........................................11 3.1 Start-up and Log in.......................................................................11 3.2 System Info...................................................................................13 3.3 Toolbox.........................................................................................14 3.4 Primary Setup...............................................................................15 3.5 DHCP Server................................................................................18 3.6 MAC Address Control ..................................................................20 Appendix A TCP/IP Configuration for Windows 95/98..........................23 A.1 Install TCP/IP Protocol into Your PC..........................................23 A.2 Set TCP/IP Protocol for Working with This Device....................25 A.3 Specifications...............................................................................32 A.4 Regulatory Compliance Information...........................................34 -3- Chapter 1 Introduction Congratulations on your purchase of this outstanding Wireless Access Point. This product is specifically designed for Small Office and Home Office needs. It provides a solution for building a LAN and sharing resources with or without wire, and is easy to configure and operate even for non-technical users. Instructions for installing and configuring this product can be found in this manual. Before you install and use this product, please read this manual carefully for fully exploiting the functions of this product. Functions and Features z High speed for wireless LAN connection 11Mbps data rate by incorporating Direct Sequence Spread Spectrum (DSSS). z Roaming Provides seamless roaming within the IEEE 802.11b WLAN infrastructure. z IEEE 802.11b compatible Allowing inter-operation among multiple vendors. z Auto fallback 11M, 5M, 2M, 1M data rate with auto fallback. z Auto-sensing Ethernet Switch Equipped with a 2-port auto-sensing Ethernet switch. z DHCP server supported All of the networked computers can retrieve TCP/IP settings automatically from this product. z Web-based configuring Configurable through any networked computer’s web browser. -4- z MAC Address Access Control supported Allows you to assign different access right for different users. z Firmware Upgradable Provides firmware upgrade via Web Browser or Windows Application. 1.2 Packing List z Wireless Access Point unit z Installation CD-ROM z Power adapter z CAT-5 UTP Fast Ethernet cable -5- Chapter 2 Hardware Installation 2.1 Panel Layout 2.1.1. Front Panel Figure 2-1 Front Panel LED: LED Function ColorStatus Description POWER Power indicationGreenOn Power is being applied to this product. M1 System status 1OrangeBlinking This product is functioning properly. WLAN Wireless activityGreenBlinking Sending or receiving data via wireless On An active station is connected to the corresponding LAN port. Link/Act. 1~2 Link status Green Blinking The corresponding LAN port is sending or receiving data. 10/100 Data Rate GreenOn Data is transmitting in 100Mbps on the corresponding LAN port. Port: RESET To reset system settings to factory defaults, please follow the steps: 1. Power off the device, 2. Press the reset button and hold, 3. Power on the device, 4. Keep the button pressed about 5 seconds, 5. Release the button, 6. Watch the M1 LED, they will flash 8 times and then M1 flash once -6- per second. -7- 2.1.2. Rear Panel Figure 2-2 Rear Panel Ports: Port Description 12VDC Power inlet: DC 1…

Text truncated - open the document above for the full version.

R:\Customer document\\SL-2011CD PLUS\ Poa-FCC (1650x2336x256 jpeg)

American Telecommunications Certification Body Inc. 6731 Whittier Ave, McLean, VA 22101 March 7, 2002 RE: Seano International Co., Ltd. FCC ID: NI3-2511SR Please provide the following information before processing can continue. 1.) Please provide block diagram of RF card. 2.) Please revise manual warning statements to advise end users of the 20cm Mobile category RF Safety prohibitions. 3.) Frequencies listed on Form 731 are not permitted. Since this is an 802.11b device, Form 731 will be changed to 2400 to 2484 MHz to 2412 to 2462 MHz. 4.) Test Report in section 3.1 should reflect revised frequency range. William H. Graff President and Examining Engineer mailto: [email protected] The items indicated above must be submitted before processing can continue on the above referenced application. Failure to provide the requested information may result in application termination. Correspondence should be considered part of the permanent submission and may be viewed from the Internet after a Grant of Equipment Authorization is issued. Please do not respond to this correspondence using the email reply button. In order for your response to be processed expeditiously, you must submit your documents through the AmericanTCB.com website. Also, please note that partial responses increase processing time and should not be submitted. Any questions about the content of this correspondence should be directed to the sender.

Page 1 ANNEX PHOTOGRAPHS OF EUT Page 2 Page 3 Page 4

C 2.7 2 9 . 2 3 m m 79.70 mm S/N: FOR HOME OR OFFICE USE FC Tested To Comply With FCC Standards This device complies with art 15 of the FCC Rules. Operation is subject to the following two conditions:(1) The device may not cause harmful interference. And(2) this device must accept any interference received, including interference that may cause undesired operation. 2-Port Switch Wireless Router Model No.: SL-2511SR Wireless Solution Provider FCC ID: NI3-2511SR S/N: FOR HOME OR OFFICE USE FC Tested To Comply With FCC Standards This device complies with art 15 of the FCC Rules. Operation is subject to the following two conditions:(1) The device may not cause harmful interference. And(2) this device must accept any interference received, including interference that may cause undesired operation. 2-Port Switch Wireless Router Model No.: SL-2511SR Wireless Solution Provider FCC ID: NI3-2511SR

Page 5 Page 6 Page 7

Page 8 Page 9 Page 10

Page 11 Page 12 Page 13 Page 14

FCC ID: NI3-2511SR ADT No.910206R02 Operational Description The transmitter of the EUT (2-Port Switch Wireless Router) is powered by adapter and connected with notebook. The antenna is dipole antenna with Inverted TNC connector. Under normal use condition, the user has to keep at least 20cm separation distance away from the radiator. For more detailed instruction, please take a look at the users manual. DSSS Information This device is Direct Sequence Spread Spectrum, the data is mixed by pseudorandom code which is an orthogonal code. The mixed data is digital modulated by BPSK and QPSK technique depends on the data rates. The CCK coding is applied for increasing the data rate, and also the processing gain will be increased. The bit rates are 1,2,5.5,11Mbps, the symbol rates are 1,1,1.375,1.375Mbps, the chip rates are always 11Mbps. So, the Chip/symbol is 11,11,8 and 8 respectively. Although the bit rate is higher, the processing gain is lower than 10, but the CCK coding used in higher bit rate will provide 2.2dB coding gain.

CHECKDRAW SENAO SHEET APPROVAL FILE NAME MODEL NO DATE DRAWING NO. PCB VER: CHECKDRAW SENAO SHEET APPROVAL FILE NAME MODEL NO DATE DRAWING NO. PCB VER:

CHECKDRAW SENAO SHEET APPROVAL FILE NAME MODEL NO DRAWING NO. DATEPCB VER: CHECKDRAW SENAO SHEET APPROVAL FILE NAME MODEL NO DRAWING NO. DATEPCB VER:

CHECKDRAW SENAO SHEET APPROVAL FILE NAME MODEL NO DRAWING NO. DATEPCB VER: CHECKDRAW SENAO SHEET APPROVAL FILE NAME MODEL NO DRAWING NO. DATEPCB VER:

FCC ID: NI3-2511SR Report No.: RF910220R03 1 Issued: March 4, 2002 FCC TEST REPORT REPORT NO.: RF910220R03 MODEL NO.: SL-2511SR, EL-2511SR RECEIVED: Feb. 22, 2002 TESTED: Feb. 19 ~ Feb. 26. 2002 APPLICANT:SENAO INTERNATIONAL CO., LTD. ADDRESS:2F, No. 531 CHUNG CHENG RD., HSIN-TIEN, TAIPEI, TAIWAN, R.O.C. ISSUED BY:Advance Data Technology Corporation LAB LOCATION:47 14 th Lin, Chiapau Tsun, Linko, Taipei, Taiwan, R.O.C. This test report consists of 49 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by CNLA, NVLAP or any government agencies. The test results in the report only apply to the tested sample. 0528 ILAC MRA Lab Code: 200102-0 FCC ID: NI3-2511SR Report No.: RF910220R03 2 Issued: March 4, 2002 Table of Contents 1CERTIFICATION........................................................................................... 4 2SUMMARY OF TEST RESULTS .................................................................. 5 3GENERAL INFORMATION ........................................................................... 6 3.1GENERAL DESCRIPTION OF EUT ............................................................. 6 3.2DESCRIPTION OF TEST MODES ............................................................... 7 3.3GENERAL DESCRIPTION OF APPLIED STANDARDS .............................. 7 3.4DESCRIPTION OF SUPPORT UNITS ......................................................... 8 4TEST TYPES AND RESULTS ...................................................................... 9 4.1CONDUCTED EMISSION MEASUREMENT................................................ 9 4.1.1LIMITS OF CONDUCTED EMISSION MEASUREMENT ...................................................... 9 4.1.2TEST INSTRUMENTS ...........................................................................................................9 4.1.3TEST PROCEDURES .......................................................................................................... 10 4.1.4TEST SETUP ....................................................................................................................... 10 4.1.5EUT OPERATING CONDITIONS......................................................................................... 11 4.1.6TEST RESULTS ................................................................................................................... 12 4.2RADIATED EMISSION MEASUREMENT................................................... 18 4.2.1LIMITS OF RADIATED EMISSION MEASUREMENT ......................................................... 18 4.2.2TEST INSTRUMENTS ......................................................................................................... 19 4.2.3TEST PROCEDURES .......................................................................................................... 20 4.2.4TEST SETUP ....................................................................................................................... 21 4.2.5EUT OPERATING CONDITIONS......................................................................................... 21 4.2.6TEST RESULTS ................................................................................................................... 22 4.36DB BANDWIDTH MEASUREMENT ......................................................... 27 4.3.1LIMITS OF 6dB BANDWIDTH MEASUREMENT ................................................................ 27 4.3.2TEST INSTRUMENTS ......................................................................................................... 27 4.3.3TEST PROCEDURE ............................................................................................................28 4.3.4TEST SETUP ....................................................................................................................... 28 4.3.5EUT OPERATING CONDITIONS......................................................................................... 28 4.3.6TEST RESULTS ................................................................................................................... 29 4.4MAXIMUM PEAK OUTPUT POWER.......................................................... 33 4.4.1LIMITS OF MAXIMUM PEAK OUTPUT POWER MEASUREMENT ................................... 33 4.4.2INSTRUMENTS.................................................................................................................... 33 4.4.3TEST PROCEDURES .......................................................................................................... 34 4.4.4TEST SETUP ....................................................................................................................... 34 4.4.5EUT OPERATING CONDITIONS......................................................................................... 34 4.4.6TEST RESULTS ................................................................................................................... 35 4.5POWER SPECTRAL DENSITY MEASUREMENT ..................................... 36 4.5.1LIMITS OF POWER SPECTRAL DENSITY MEASUREMENT ........................................... 36 4.5.2TEST INSTRUMENTS ......................................................................................................... 36 4.5.3TEST PROCEDURE ............................................................................................................37 4.5.4TEST SETUP ....................................................................................................................... 37 4.5.5EUT OPERATING CONDITION ........................................................................................... 37 4.5.6TEST RESULTS ................................................................................................................... 38 4.6BAND EDGES MEASUREMENT ..............................................…

Text truncated - open the document above for the full version.

FCC ID: NI3-2511SR Report No.: RF910220R03 47 Issued: March 4, 2002 5 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST FCC ID: NI3-2511SR Report No.: RF910220R03 48 Issued: March 4, 2002 RADIATED EMISSION TEST