NYOSISJC10BEMCONTROL UNIT IMMOBILIZER

1.Model No. IMMOBILIZER : SISJC10BEM 2.Make Shinchang Electrics Co.,Ltd. 3.Name and address of manufacturer Shinchang Electrics Co.,Ltd. 734-2, Wonshi-Dong, Ansan-Si, Kyonggi-Do, Korea. 4.Address of assembly plant Shinchang Electrics Co.,Ltd. 734-2, Wonshi-Dong, Ansan-Si, Kyonggi-Do, Korea. 1. Product description 1.1 product summary Immobilizer is a vehicle anti-theft system by electronic identification of owner. The starter does not operate if a thief forces the door open and the engine started. 1.2 specification * The two reason why two reason for input frequency: CPU can recognize when CPU recognition CODE used for immobilizer send descripted data as radio frequency at transponder using binary code. That's why we establish 134.2khz and 123.2khz for recognizing 0 or 1 at CPU connect typeconnector type produce/modelSINCHANG/IMMOBILIZER oriented naturedirectivity polarizationnone antenna length- antenna gain- amplifiernothing antenna typenone size(W*H*D unit:mm ) communication method weight 65*60*25 -30 ~+80°C consumption current use power listspecification output freq. 134.2kHz input freq. 0 : 134.2kHz use frequency 28.7g(inclusion Case) oscillation mathod signal form modulation mathod use temperature F1D intermittent run HALF DPX RESONATOR AM modulation 1 : 123.2kHz 30ms(typ.) 500mA(Max.) DC12V (vehicle BATTERY) 1.3 Structure ① TRANSPONDER Transponder send response and SERIAL NUMBER to immobilizer changed ENCRYPTION KEY in ASIC whenever the Transponder receive ENERGY or CHALLENGE from radio frequency. ② COIL ANTENNA Ls (Inductance) : 444±20uH at 134.2KHz(equipped with STR'G LOCK) coil antenna is supplied the energy and challenge to transponder That is receiving and transmiited the signal from transponder to IMMOBILIZER in the SHL(STEERING HANDLE LOCK) ③ IMMOBILIZER ECU IMMO is operated the COIL ANTENNA. The information ,that is Receiving signal from COIL ANTENNA compared and analyzed, is transmitted to ENGINE ECU ④ ENGINE ECU If the Igition is on, ENGINE ECU are received related with transponder information from IMMOBILIZER ECU then perform engine starting or impossible starting. 6 12 ASIC CONDENSER COIL ② ID CODE MAGNETIC POWER ① Cylinder lock housing BATTERY ③ Question code Answer code ④

SHINCHANG ELECTRICS CO., LTD. 734-2, Wonshi-dong, Danwon-gu, Ansan-si, Gyunggi-do, 425-090, Korea Tel: +82-41-0910-472, Fax: +82-41-9010-419 Date: May 07, 2008 Compliance Certification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA To whom it may concern: I, the undersigned, hereby authorize Mr. Y.K.Kwon/Director of ONETECH Corp., and hereafter referred to as ONETECH, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Mr. Y.K.Kwon of ONETECH on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing CCS as our agent, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i) keep a record of all complaints made known to the us relating to the product’s compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested; j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Mr. Woo, Jung / Director Shinchang Electrics Co., Ltd.

SHINCHANG ELECTRICS CO., LTD. 734-2, Wonshi-dong, Danwon-gu, Ansan-si, Gyunggi-do, 425-090, Korea Tel: +82-41-910-0463, Fax: +82-41-901-0519 Date: July 28, 2010 FCC Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Attention: Application Examiner Reviewing Engineer Re: Request for confidentiality per Section 0.459 of FCC Rules Applicant: Shinchang Electrics Co., Ltd. FCC ID: NYOSISJC10BEM To whom it may concern, Request is hereby submitted, on behalf of my client, Shinchang Electrics, Co., Ltd, to withhold from public review certain portions of the application for equipment certification for the referenced FCC identifier. In particular, the following sections of the application and report are requested to be kept confidential: Schematics Block Diagram Parts List Operational Description Rationale for request for confidentiality: Shinchang Electrics Co., Ltd has invested considerable time and materials in research and development to produce the referenced product. Disclosure of the confidential portions of this application to competitors would give them competitive advantage in developing similar products. If you have questions or need further information, please contact the undersigned. Sincerely Yours, Mr. Woo, Jung / Director Shinchang Electrics Co., Ltd.

FCC ID. : NYOSISJC10BEM Page 1 of 3 Report No. : E107R-059 It should not be reproduced except in full, without the written approval of ONETECH Corp. EMC-003 (Rev.1) HEAD OFFICE : #505 SK Apt. Factory, 223-28 Sangdaewon1-dong, Jungwon-gu, Seongnam-si, Gyeonggi-do 462-705 Korea (TEL: +82-31-746-8500, FAX: +82-31-746-8700) EMC Testing Dept : 307-51 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea. (TEL: +82-31-765-8289, FAX: +82-31-766-2904) FCC ID. : NYOSISJC10BEM Page 2 of 3 Report No. : E107R-059 It should not be reproduced except in full, without the written approval of ONETECH Corp. EMC-003 (Rev.1) HEAD OFFICE : #505 SK Apt. Factory, 223-28 Sangdaewon1-dong, Jungwon-gu, Seongnam-si, Gyeonggi-do 462-705 Korea (TEL: +82-31-746-8500, FAX: +82-31-746-8700) EMC Testing Dept : 307-51 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea. (TEL: +82-31-765-8289, FAX: +82-31-766-2904) FCC ID. : NYOSISJC10BEM Page 3 of 3 Report No. : E107R-059 It should not be reproduced except in full, without the written approval of ONETECH Corp. EMC-003 (Rev.1) HEAD OFFICE : #505 SK Apt. Factory, 223-28 Sangdaewon1-dong, Jungwon-gu, Seongnam-si, Gyeonggi-do 462-705 Korea (TEL: +82-31-746-8500, FAX: +82-31-746-8700) EMC Testing Dept : 307-51 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea. (TEL: +82-31-765-8289, FAX: +82-31-766-2904)

FCC ID. : NYOSISJC10BEM Page 1 of 1 Report No. : E107R-059 It should not be reproduced except in full, without the written approval of ONETECH Corp. EMC-003 (Rev.1) HEAD OFFICE : #505 SK Apt. Factory, 223-28 Sangdaewon1-dong, Jungwon-gu, Seongnam-si, Gyeonggi-do 462-705 Korea (TEL: +82-31-746-8500, FAX: +82-31-746-8700) EMC Testing Dept : 307-51 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea. (TEL: +82-31-765-8289, FAX: +82-31-766-2904) IDENTIFICATION LABEL: PROPOSED FCC ID LABEL The FCC ID shall be permanently affixed to the rear side of the equipment FCC ID AREA This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operations. Made in Korea FCC ID : NYOSISJC10BEM

FCC ID. : NYOSISJC10BEM Page 1 of 2 Report No. : E107R-059 It should not be reproduced except in full, without the written approval of ONETECH Corp. EMC-003 (Rev.1) HEAD OFFICE : #505 SK Apt. Factory, 223-28 Sangdaewon1-dong, Jungwon-gu, Seongnam-si, Gyeonggi-do 462-705 Korea (TEL: +82-31-746-8500, FAX: +82-31-746-8700) EMC Testing Dept : 307-51 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea. (TEL: +82-31-765-8289, FAX: +82-31-766-2904) FCC ID. : NYOSISJC10BEM Page 2 of 2 Report No. : E107R-059 It should not be reproduced except in full, without the written approval of ONETECH Corp. EMC-003 (Rev.1) HEAD OFFICE : #505 SK Apt. Factory, 223-28 Sangdaewon1-dong, Jungwon-gu, Seongnam-si, Gyeonggi-do 462-705 Korea (TEL: +82-31-746-8500, FAX: +82-31-746-8700) EMC Testing Dept : 307-51 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea. (TEL: +82-31-765-8289, FAX: +82-31-766-2904)

FCC ID. : NYOSISJC10BEM Page 1 of 13 Report No. : E107R-059 It should not be reproduced except in full, without the written approval of ONETECH Corp. EMC-003 (Rev.1) HEAD OFFICE : #505 SK Apt. Factory, 223-28 Sangdaewon1-dong, Jungwon-gu, Seongnam-si, Gyeonggi-do 462-705 Korea (TEL: +82-31-746-8500, FAX: +82-31-746-8700) EMC Testing Dept : 307-51 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea. (TEL: +82-31-765-8289, FAX: +82-31-766-2904) ELECTROMAGNETIC EMISSION C OMPLIANCE REPORT FOR LOW POWER TRANSMITTER BELOW 1 705 KHZ Test Report No. : E107R-059 AGR No. : A107A-081 Applicant : SHINCHANG ELECTRICS CO., LTD. Address : 734-2, Wonshi-dong, Danwon-gu, Ansan-si, Kyungki-do, 425-090, Korea Manufacturer : SHINCHANG ELECTRICS CO., LTD. Address : 734-2, Wonshi-dong, Danwon-gu, Ansan-si, Kyungki-do, 425-090, Korea Type of Equipment : CONTROL UNIT IMMOBILIZER FCC ID. : NYOSISJC10BEM Model Name : SISJC10BEM Serial number : N/A Total page of Report : 13 pages (including this page) Date of Incoming : July 20, 2010 Date of issuing : July 29, 2010 SUMMARY The equipment complies with the regulation of FCC Part 15 Subpart C Section 15.209. This test report contains only the result of a single test of the sample supplied for the examination. Prepared by: Reviewed by: Young-Min, Choi / Asst. Chief Engineer Y. K. Kwon / Managing Director EMC/RF Center EMC/RF Center ONETECH Corp. ONETECH Corp. FCC ID. : NYOSISJC10BEM Page 2 of 13 Report No. : E107R-059 It should not be reproduced except in full, without the written approval of ONETECH Corp. EMC-003 (Rev.1) HEAD OFFICE : #505 SK Apt. Factory, 223-28 Sangdaewon1-dong, Jungwon-gu, Seongnam-si, Gyeonggi-do 462-705 Korea (TEL: +82-31-746-8500, FAX: +82-31-746-8700) EMC Testing Dept : 307-51 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea. (TEL: +82-31-765-8289, FAX: +82-31-766-2904) CONTENTS PAGE 1. VERIFICATION OF COMPLIANCE ............................................................................................................................3 2. GENERAL INFORMATION...........................................................................................................................................4 2.1 PRODUCT DESCRIPTION..................................................................................................................................................4 2.2 ALTERNATIVE TYPE(S)/MODEL(S); ALSO COVERED BY THIS TEST REPORT..................................................................4 2.3 RELATED SUBMITTAL(S) / GRANT(S).............................................................................................................................4 2.4 PURPOSE OF THE TEST....................................................................................................................................................4 2.5 TEST METHODOLOGY.....................................................................................................................................................4 2.6 TEST FACILITY................................................................................................................................................................4 3. SYSTEM TEST CONFIGURATION..............................................................................................................................5 3.1 JUSTIFICATION................................................................................................................................................................5 3.2 PERIPHERAL EQUIPMENT................................................................................................................................................5 3.3 MODE OF OPERATION DURING THE TEST........................................................................................................................5 3.4 EQUIPMENT MODIFICATIONS.........................................................................................................................................5 3.5 CONFIGURATION OF TEST SYSTEM................................................................................................................................5 3.6 ANTENNA REQUIREMENT...............................................................................................................................................6 4. PRELIMINARY TEST .....................................................................................................................................................6 4.1 AC POWER LINE CONDUCTED EMISSIONS TESTS..........................................................................................................6 4.2 RADIATED EMISSIONS TESTS..........................................................................................................................................6 5. FINAL RESULT OF MEASURMENT ...........................................................................................................................7 5.1 RADIATED EMISSION TEST BELOW 30 MHZ..................................................................................................................7 5.2 RADIATED EMISSION TEST ABOVE 30 MHZ...................................................................................................................8 5.2.1 Operating Condition: Tx Mode...............................................................................................................................8 5.2.2 Operating Condition: Rx Mode...............................................................................................................................9 5.3 BANDWIDTH OF THE OPERATING FREQUENCY.............................................................................................................10 6. FIELD STRENGTH CALCULATION .........................................................................................................................12 7. LIST OF TEST EQUIPMENT....................…

Text truncated - open the document above for the full version.

FCC ID. : NYOSISJC10BEM Page 1 of 1 Report No. : E107R-059 It should not be reproduced except in full, without the written approval of ONETECH Corp. EMC-003 (Rev.1) HEAD OFFICE : #505 SK Apt. Factory, 223-28 Sangdaewon1-dong, Jungwon-gu, Seongnam-si, Gyeonggi-do 462-705 Korea (TEL: +82-31-746-8500, FAX: +82-31-746-8700) EMC Testing Dept : 307-51 Daessangnyeong-ri, Chowol-eup, Gwangju-si, Gyeonggi-do 464-862 Korea. (TEL: +82-31-765-8289, FAX: +82-31-766-2904) Radiated Emission Test