O3U-98163Inductive Toy Doll (RFID Tag Reader)

BATTERIES: Allysen needs 3 “AAA” and 4 “AA” alkaline batteries in order to work. Please have an adult insert the batteries (not included) as shown. IMPORTANT NOTE: If you turn Allysen off or replace the batteries, her internal clock will stop. If she is turned off longer than 5 minutes, her clock will become incorrect. Should this happen, you can reset any of Allysen’s settings at any time by squeezing both hands simultaneously for approxi- mately 10 seconds. Allysen will automatically power down into Quiet Mode to save battery power if left unattended for a long period of time. To awaken her, squeeze either hand. To put Allysen into Quiet Mode, use one of two methods: 1) squeeze her right hand for approximately 10 seconds or 2) When Allysen asks, “What do you want to do?” reply, “Take a break.” Remember: to wake her, just squeeze either hand. WARNING: • Do not use rechargeable batteries; • Non-rechargeable batteries are not to be recharged; • Different types of batteries or new and used batteries are not to be mixed; • Only batteries of the same or equivalent type as recommended are to be used; • Batteries are to be inserted with the correct polarity; • Exhausted batteries should be removed from the toy; • The supply terminals should not be short-circuited. Battery regulations: Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries. 1 4 2 3 5 8 7 6 Use of the ON/OFF Switch: The OFF Switch should only be used if you plan NOT to play with Allysen for several months. Turning Allysen off with the ON/OFF switch stops her internal clock. If she is turned off longer than 5 minutes, her clock will become incorrect. Should this happen, you can reset any of Allysen’s settings at any time by squeezing both hands simultaneously for approximately 10 seconds. Please make sure the latch is in the LOCK position or Allysen will turn off. If the latch is in the UNLOCK position for longer than 5 minutes, her clock will need to be reset. INSTRUCTIONS Start-up (Requires Adult Assistance) Once the batteries are inserted, turn the switch on Allysen’s back to the ON position. Squeeze either of Allysen’s hands to wake her up and she will go through the Start-Up Routine. You will only need to do this once or each time the batteries are replaced. Note: If you turn the switch on her back to the OFF position, her internal clock will stop. If she is turned off longer than 5 minutes, her clock will become incorrect. Should this happen, you can reset any of Allysen’s settings at any time by squeezing both of Allysen’s hands simultaneously for approximately 10 seconds. Please make sure the latch is in the LOCK position or Allysen will turn off. If the latch is in the UNLOCK position for longer than 5 minutes, her clock will need to be reset. Before play can begin you must set the correct date & time. As you go through the prompts in the Start-Up Routine, you will be asked to respond to Allysen by squeezing her left hand to set the year, month, date and time. Time is a very important feature for Allysen. Make sure to set the correct day, month, and year in the Start-Up routine. Allysen needs to know the date and time so that she can remind you of holidays, remember when it’s your Birthday, etc. Please be patient and go through the steps carefully. Setting the Time and Telling Time When setting the hour, decide the closest number the hour hand on your home clock is pointing to and squeeze her left hand until she says the hour. When squeezing Allysen’s left hand, make sure to continually squeeze her hand until she says the right time. As soon as you let go of her hand, she will stop on the number she last said before you let go. When setting the minutes, note that Allysen tells the time in minutes by using 5 minute increments. Decide the closest number the minute hand on your home clock is pointing to and squeeze her left hand until she says the number of minutes closest to the actual time. Once you’ve completed entering in the correct time, Allysen will ask you to confirm if it is morning, afternoon or night. Once prompted, simply answer by saying either ‘morning’,‘afternoon’, or ‘night’. Once you’ve completed entering in the correct time, Allysen will ask you to confirm if it is morning, afternoon or night. Once prompted, simply answer by saying either ‘morning’, ‘afternoon’ or ‘night’. For example, if it’s 1:38pm, you should input 1 for the hour and 40 for the minutes, and answer “afternoon”. Setting the Year, Month and Date Allysen will prompt you to input the correct year, month and date. Once prompted by Allysen, simply squeeze her left hand to select the current year, month, and date. When squeezing Allysen’s left hand, make sure to continually squeeze her hand until she says the right year, month and date. As soon as you let go of her hand, she will stop on the number she last said before you let go. Setting Your Birth Date Allysen wants to know when your birthday is. Once prompted, squeeze Allysen’s left hand to select the month and date of your birthday. Once you do this, she’ll remember and wish you happy birthday on your special day. She will also remind you from time to time how far off your birthday is. Choosing a Nickname Allysen will ask you to choose a nickname for her to call you. She will ask ‘Would you like me to call you: Girlfriend, Jelly Bean, Best Friend, Girlie, Pickles or Sweetie?’ Please answer with the nickname you like best from the choices listed and Allysen will remember your selected nickname. Changing Nickname, Time, Date, Year & Birthdate If you want to change the nickname Allysen calls you or the time, date, year or birthdate, just squeeze both of Allysen’s hands simultaneously for approximately 10 seconds. 1. Right Hand Sensor: Allysen will know when you squeeze her right hand to put her into Quiet Mode and can also recognize her accessories when you place them in her right hand. If you look closely, you will see a small…

Text truncated - open the document above for the full version.

FCC ID: O3U-98163 Ophoto1 Ophoto2 FCC ID: O3U-98163 Ophoto3 Ophoto4 FCC ID: O3U-98163 Ophoto5 Ophoto6 FCC ID: O3U-98163 Ophoto7 Ophoto8 FCC ID: O3U-98163 Ophoto9 Ophoto10

Item No.: 98163 Label Size: 50mm x 12mm 50mm 12mm FCC ID:O3U-98163 Label Size: 18mm x 2mm 18mm 2mm

FCC ID: O3U-98163 Iphoto1 Iphoto2 FCC ID: O3U-98163 Iphoto3 Iphoto4 FCC ID: O3U-98163 Iphoto5 Iphoto6 FCC ID: O3U-98163 Iphoto7 Iphoto8 FCC ID: O3U-98163 Iphoto9 Iphoto10 FCC ID: O3U-98163 Iphoto11 Iphoto12 FCC ID: O3U-98163 Iphoto13 Iphoto14

FCC ID: O3U-98163 Iphoto15 Iphoto16 FCC ID: O3U-98163 Iphoto17 Iphoto18 FCC ID: O3U-98163 Iphoto19 Iphoto20 FCC ID: O3U-98163 Iphoto21 Iphoto22 FCC ID: O3U-98163 Iphoto23 Iphoto24 FCC ID: O3U-98163 Iphoto25 Iphoto26 FCC ID: O3U-98163 Iphoto27 Iphoto28

FCC ID: O3U-98163 Iphoto29 Iphoto30 FCC ID: O3U-98163 Iphoto31 Iphoto32 FCC ID: O3U-98163 Iphoto33 Iphoto34 FCC ID: O3U-98163 Iphoto35 Iphoto36 FCC ID: O3U-98163 Iphoto37 Iphoto38 FCC ID: O3U-98163 Iphoto39 Iphoto40 FCC ID: O3U-98163 Iphoto41 Iphoto42

FCC ID: O3U-98163 Iphoto43 Iphoto44 FCC ID: O3U-98163 Iphoto45 Iphoto46 FCC ID: O3U-98163 Iphoto47 Iphoto48 FCC ID: O3U-98163 Iphoto49 Iphoto50 FCC ID: O3U-98163 Iphoto51 Iphoto52 FCC ID: O3U-98163 Iphoto53 Iphoto54 FCC ID: O3U-98163 Iphoto55 Iphoto56

FCC ID: O3U-98163 Iphoto57 Iphoto58 FCC ID: O3U-98163 Iphoto59 Iphoto60 FCC ID: O3U-98163 Iphoto61 Iphoto62 FCC ID: O3U-98163 Iphoto63 Iphoto64 FCC ID: O3U-98163 Iphoto65 Iphoto66 FCC ID: O3U-98163 Iphoto67 Iphoto68 FCC ID: O3U-98163 Iphoto69 Iphoto70 FCC ID: O3U-98163 Iphoto71 Iphoto72 FCC ID: O3U-98163 Iphoto73 Iphoto74

FCC ID: O3U-98163 Iphoto75 Iphoto76 FCC ID: O3U-98163 Iphoto77 Iphoto78 FCC ID: O3U-98163 Iphoto79 Iphoto80 FCC ID: O3U-98163 Iphoto81 Iphoto82 FCC ID: O3U-98163 Iphoto83 Iphoto84 FCC ID: O3U-98163 Iphoto85

FCC ID: O3U-98163 Technical Description : The brief circuit description is listed as follows : - L201 and associated circuit act as Antenna and Antenna Matching Circuit for the head reader. - L202 and associated circuit act as Antenna and Antenna Matching Circuit for the hand reader. - U201(HL5233), X201 and associated circuit act as RFID reader (head reader) and 13.56 MHz Oscillator. - U202(HL5233), X202 and associated circuit act as RFID reader (hand reader) and 13.56 MHz Oscillator. - U101(RSC-4128) acts as MCU and Speech Recognition Processor. - U102(K8D3216UBC) acts as NOR-type Flash Memory. - U103 and U104 act as Logic Gates. - U105(AT24C04N) acts as EEPROM. - U301(74HC374) acts as 3-State Octal D-type Flip-Flop. - U302(74HC373) acts as 3-State Octal D-type Latch. - U2 acts as Audio Amplifier. - Q302 to Q307 and associated circuit act as Eye Motor Driver. - Q308 to Q313 and associated circuit act as Mouth Motor Driver. - CN101 acts as cartridge Connector. Antenna Used : Two loop antennas have been used.

123456 A B C D 654321 D C B A utchison arbourRing ACEFIELD LIMITED Product Development & Engineering Model Name:Allysen Description: Design by: Date:Date:2006-06-01Date:2006-06-01Date:2006-06-01 Project No:PM98163 Draw by:YangFuZhi File name:Size: A4 Check by:LTH Sheet: 1of 4 Rev:0 Approved by:Vincent C108 12PF C109 12PF C111 33PF C110 33PF X101 3.58MHz X102 32KHz VDD C118 104 C116 473 C115 104 A 0 P 0 1 A 1 P 0 2 A 2 P 0 3 A 3 A 4 P 0 4 A 5 P 0 5 A 6 P 0 6 D101 IN4148 C112 1u C120 2.2u C121 1u C122 100u D103 IN4148 D102 IN4148 R103 1.5K C117 103 C113 104 C123 3300 R105 680 R104 100 C119 104 VDD P101 MIC -58dbm P0.0 1 D7 2 D6 3 PDN 4 D5 5 D4 6 GND 7 XO1 8 XI1 9 VDD 10 XM 11 XO2 12 XI2 13 D3 14 D2 15 P2.7 16 D1 17 D0 18 GND 19 VDD 20 P2.6 21 M1 22 P2.5 23 BRKPT 24 RESET 25 D A C O U T 2 6 A V S S 2 7 V C M 2 8 M I C I N 2 2 9 M I C I N 1 3 0 M I C G N D 3 1 V R E F 3 2 A V D D 3 3 N C 3 4 P 2 . 4 3 5 P 2 . 3 3 6 N C 3 7 P 2 . 2 3 8 G N D 3 9 P 2 . 1 4 0 P 2 . 0 4 1 G N D 4 2 V D D 4 3 R D F 4 4 W R C 4 5 R D R 4 6 W R C 4 7 A 1 9 4 8 A 1 8 4 9 T E S T 5 0 PLLEN 51 A17 52 P1.7 53 A16 54 P1.6 55 GND 56 VDD 57 A15 58 P1.5 59 A14 60 P1.4 61 A13 62 P1.3 63 A12 64 P1.2 65 A11 66 P1.1 67 A10 68 GND 69 VDD 70 A9 71 P1.0 72 A8 73 A7 74 P0.7 75 N C 7 6 P 0 . 6 7 7 A 6 7 8 N C 7 9 P 0 . 5 8 0 A 5 8 1 N C 8 2 P 0 . 4 8 3 A 4 8 4 N C 8 5 G N D 8 6 P W M 0 8 7 P W M 1 8 8 V D D 8 9 N C 9 0 A 3 9 1 P 0 . 3 9 2 N C 9 3 A 2 9 4 P 0 . 2 9 5 A 1 9 6 N C 9 7 P 0 . 1 9 8 A 0 9 9 N C 1 0 0 U101 RSC-4128 VDD A0 1 A1 2 A2 3 GND 4 SDA 5 SCL 6 WP 7 VCC 8 U105 AT24CO4N C114 104VDD C101 104 C102 104 C103 104 C104 104 C105 104 C106 104 VDD P07 A7 A8 P10 A9 P00 D7 D6 PDN D5 D4 D3 D2 P27 D1 D0 DACOUT A10 A11 A12 A13 A14 A15 A16 A17 P11 P12 P13 P14 P15 P16 P17 P 2 0 P 2 1 P 2 2 P 2 3 P 2 4 A 1 8 A 1 9 W R D RDR RDF P21 P04 P07 P26 P25 Y0 4 Y1 5 Y2 6 Y3 7 G 1 A 2 B 3 1 6 8 U104A 74HC139 Y3 9 Y2 10 Y1 11 Y0 12 A 14 B 13 G 15 U104B 74HC139 R102 100K 1 2 3 U103A 74C08 4 5 6 U103B 74C08 8 10 9 U103C 74CO8 12 13 11 1 4 7 U103D 74CO8 C11 104 OE 28 A16 48 A15 1 A14 2 A13 3 A12 4 A11 5 A10 6 A9 7 A8 8 A19 9 RY/BY 15 A20 10 A18 16 A17 17 A7 18 A6 19 A5 20 A4 21 A3 22 A2 23 A1 24 A0 25 NC 13 BYTE 47 D15/A-1 45 DQ14 43 DQ13 41 DQ12 39 DQ11 36 DQ10 34 DQ9 32 DQ8 30 DQ7 44 DQ0 29 DQ1 31 DQ2 33 DQ3 35 DQ4 38 DQ5 40 DQ6 42 CE 26 WE 11 WP 14 RESET 12 V S S 2 7 V S S 4 6 V D D 3 7 U102 K8D3216UBC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 2021 40 22 39 23 38 24 37 25 36 26 35 27 34 28 33 29 32 30 31 CN101 CARTRIDGE CONNECTOR C107 104 VDD VDD VDD VDD A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 D0 D1 D2 D3 D4 D5 D6 D7 A21 A20 VDD CD VDD GND VDD PDN CD P00 P01 OC WE WRD CEX R17 100KVDD P10 P11 P12 P13 RDF RDP4 A0A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 A21 D0 D1 D2 D3 D4 D5 D6 D7 PDN PB4 EEPROM CLEAR P00 ALLYSON MAIN MCU & MEMORY R101 100K P14 Model NO. : 98163 123456 A B C D 654321 D C B A utchison arbourRing ACEFIELD LIMITED Product Development & Engineering Model Name:Allysen Description: Design by: Date:Date:2006-06-01Date:2006-06-01Date:2006-06-01 Project No:PM98163 Draw by:YangFuZhi File name:Size: A4 Check by:LTH Sheet: 2 of 4 Rev:0 Approved by:Vincent Q1 2SC5343 R14 680 R16 100K VAAA(4.5V)VAA(6V) PB2 LEFT HAND PB3 RIGHT HAND Q2 M7 R18 10K R15 680 R1 10K P16 P17 P23 P24 BATT_CHECK 1 2 3 4 5 6 7 8 U2 SPY0030A C9 104 C8 224 C7 104 R10 6.8K R9 20K C6 220u SP1 SPEAKER VCC P21 DACOUT Vout 3 Vin 2 G N D 1 U1 7533 C2 100u C1 100u D1 IN4148 SW1 ON/OFF PTC1 0.75A PTC2 0.3A BT1 4.5V BT2 6V L3 10uH VDD VAA(6V) ON OFF ON OFF "AA SIZE X 4" "AAA SIZE X 3" L4 10uH VAAA(4.5V) R4 10 ALLYSON C60 10u R90 10K Q3 M7 RP201 RES PORT RP202 RES PORT RP203 RES PORT R201 10K(1%) C201 104 UPPER BACK LOWER BACK RIGHT FOOT P25 P26 P27 P22 P20 VCC D3 2.7v D4 3.6v SW2 2.2K(1%) (located on clothes) 2.7K(1%) (located on pants) 82K(1%) (located on shoes) Model NO. : 98163 123456 A B C D 654321 D C B A utchison arbourRing ACEFIELD LIMITED Product Development & Engineering Model Name:Allysen Description: Design by: Date:Date:2006-06-01Date:2006-06-01Date:2006-06-01 Project No:PM98163 Draw by:YangFuZhi File name:Size: A4 Check by:LTH Sheet: 3 of 4 Rev:0 Approved by:Vincent Q301 M7 Q314 2SC5343 R301 47K R314 100K C302 104 R315 47K VDD C308 104 100K X 8 EyemotFwd EyemotBwd MouMotFwd MouMotBwd RK301 D9 P21 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7 RDP4 WP0 WP1 WP2 WP3 WP4 WP5 BATT_CHECK OC WRD M301 M Q303 772 Q302 772 Q304 9014 Q307 882 Q306 882 Q305 9014 C304 104 C301 104 C303 104 R303 100 R302 100 R305 1K R304 1K D301 IN4148 L301 10uH L302 10uH VAA(6V) EyeMotFwd EyeMotBwd M302 M Q309 772 Q308 772 Q310 9014 Q313 882 Q312 882 Q311 9014 C307 104 C305 104 C306 104 R311 100 R310 100 R313 1K R312 1K D306 IN4148 L303 10uH L304 10uH VAA(6V) MouMotFwd MouMotBwd 1234 DISC (EYE) 1234 DISC (MOUTH) W P 3 W P 4 W P 5 W P 0 W P 1 W P 2 P D N P D N MOTOR-EYE MOTOR-MOUTH_CHIN 1 23 45678 ALLYSEN MOTOR CONTROL VDD OC 1 V D D 2 0 1D 3 G N D 1 0 1Q 2 CLK 11 2Q 5 8D 18 2D 4 8Q 19 3D 7 7Q 16 3Q 6 7D 17 4Q 9 6D 14 4D 8 6Q 15 5D 13 5Q 12 U301 74HC374 OC 1 O1 2 D1 3 D2 4 O2 5 O3 6 D3 7 D4 8 O4 9 O5 12 D5 13 D6 14 O6 15 O7 16 D7 17 D8 18 O8 19 C 11 G N D 1 0 V D D 2 0 U302 74HC373 DETECT THE EYE LOCATION DETECT THE MOUTH LOCATION Model NO. : 98163 123456 A B C D 654321 D C B A utchison arbourRing ACEFIELD LIMITED Product Development & Engineering Model Name:Allysen Description: Design by: Date:Date:2006-06-01Date:2006-06-01Date:2006-06-01 Project No:PM98163 Draw by:YangFuZhi File name:Size: A4 Check by:LTH Sheet: 4 of 4 Rev:0 Approved by:Vincent SL 1 READY 2 PLAYMODE 3 LHOLDN 4 SDATAI/OUT7 6 CLOCKI/OUT/6 8 DATAI/OUT5 10 OUT4 12 OUT3 14 OUT2 16 OUT1 18 OUT0 20 VDD1 24 VDD 23 VSS 48 VSS2 47 COM 45 IN1 43 AO1 41 IN2 39 AO2 38 A03 37 OSC1 35 OSC2 34 OENB 31 END 32 VDD2 29 VDD 28 VSS1 27 DRIV1 25 U201 HL5233 C206 104 C202 104 C203 103 C208 39P C210 10P C212 10P C214 15P C215 15p C220 104 X201 13.56MHz VC201 1-50P C218 10uF L201 ANTENNA R…

Text truncated - open the document above for the full version.

• The test results reported in this report shall refer only to the sample actually tested and shall not refer or be deemed to refer to bulk from which such a sample may be said to have been obtained. • This report shall not be reproduced except in full without prior authorization from Intertek Testing Services Hong Kong Limited. • The evaluation data of the report will be kept for 3 years from the date of issuance. FCC ID : O3U-98163 Playmates Toys Int’l. Ltd./Playmates Asia Services Ltd. Application For Certification (FCC ID: O3U-98163) Transmitter Sample Description : Amazing Allysen Model : 98163 Additional Model : 98186 We hereby certify that the sample of the above item is considered to comply with the requirements of FCC Part 15, Subpart C for Intentional Radiator, mention 47 CFR [4-5-2005] 0611653 AC/at August 18, 2006 INTERTEK TESTING SERVICES FCC ID: O3U-98163 i LIST OF EXHIBITS INTRODUCTION EXHIBIT 1: General Description EXHIBIT 2: System Test Configuration EXHIBIT 3: Emission Results EXHIBIT 4: Equipment Photographs EXHIBIT 5: Product Labelling EXHIBIT 6: Technical Specifications EXHIBIT 7: Instruction Manual EXHIBIT 8: Miscellaneous Information INTERTEK TESTING SERVICES FCC ID: O3U-98163 ii MEASUREMENT/TECHNICAL REPORT Playmates Toys Int’l. Ltd./Playmates Asia Services Ltd. - MODEL: 98163 FCC ID: O3U-98163 August 18, 2006 This report concerns (check one:) Original Grant X Class II Change Equipment Type: Low Power Transmitter (example: computer, printer, modem, etc.) Deferred grant requested per 47 CFR 0.457(d)(1)(ii)? Yes No X If yes, defer until: date Company Name agrees to notify the Commission by: date of the intended date of announcement of the product so that the grant can be issued on that date. Transition Rules Request per 15.37? Yes No X If no, assumed Part 15, Subpart C for intentional radiator - the new 47 CFR [4-5- 2005 Edition] provision. Report prepared by: Chan Kar Ming, Anthony Intertek Testing Services 2/F., Garment Center, 576, Castle Peak Road, HONG KONG Phone: 852-2173-8517 Fax: 852-2742-9149 INTERTEK TESTING SERVICES FCC ID: O3U-98163 iii Table of Contents 1.0 General Description................................................................................................ 2 1.1 Product Description ............................................................................................. 2 1.2 Related Submittal(s) Grants................................................................................. 2 1.3 Test Methodology................................................................................................ 3 1.4 Test Facility ......................................................................................................... 3 2.0 System Test Configuration..................................................................................... 5 2.1 Justification.......................................................................................................... 5 2.2 EUT Exercising Software ..................................................................................... 5 2.3 Special Accessories............................................................................................. 5 2.4 Equipment Modification ....................................................................................... 6 2.5 Support Equipment List and Description .............................................................. 6 3.0 Emission Results .................................................................................................... 8 3.1 Field Strength Calculation .................................................................................... 9 3.1 Field Strength Calculation (cont’d) ..................................................................... 10 3.2 Radiated Emission Configuration Photograph .................................................... 11 3.3 Radiated Emission Data .................................................................................... 12 3.4 Frequency Tolerance......................................................................................... 16 4.0 Equipment Photographs ....................................................................................... 19 5.0 Product Labelling.................................................................................................. 21 6.0 Technical Specifications....................................................................................... 23 7.0 Instruction Manual ................................................................................................ 25 8.0 Miscellaneous Information ................................................................................... 27 8.1 Measured Bandwidth......................................................................................... 28 8.2 Emission Test Procedures ................................................................................ 29 8.2 Emission Test Procedures (Cont’d).................................................................... 30 INTERTEK TESTING SERVICES FCC ID: O3U-98163 iv List of attached file Exhibit type File Description filename Test Report Test Report report.pdf Operation Description Technical Description descri.pdf Test Setup Photo Radiated Emission radiated photos.doc Test Report Bandwidth Plot bw.pdf External Photo External Photo external photos.doc Internal Photo Internal Photo internal photos.doc Block Diagram Block Diagram block.pdf Schematics Circuit Diagram circuit.pdf ID Label/Location Label Artwork and Location label.pdf User Manual User Manual manual.pdf INTERTEK TESTING SERVICES FCC ID: O3U-98163 1 EXHIBIT 1 GENERAL DESCRIPTION INTERTEK TESTING SERVICES FCC ID: O3U-98163 2 1.0 General Description 1.1 Product Description The equipment under test (EUT) is a transmitter for an Inductive toy doll operating at 13.56 MHz which is controlled by a crystal. The EUT is powered by 4 AA and 3 AAA batteries. This toy set includes a toy doll (RFID rea…

Text truncated - open the document above for the full version.

INTERTEK TESTING SERVICES Front View Back View