O4D-IC400WisReed Module

Fujitsu 2.4G Mesh Radio Module And NIC (Network Interface Card) User Manual V1.0 – 25 June, 2014 Copyright 2014 Fujitsu Limited Fujitsu 2.4G Mesh Radio Module And NIC User Manual Revision History Page 1 Copyright 2014 Fujitsu Limited Ve r Category Description of Change Date Author 1.0 1.1 First version Update content - 1. Add operating Voltage and Temperature 2. Add warning. 25.06.2014 25.06.2014 Fujitsu WNC Fujitsu 2.4G Mesh Radio Module And NIC User Manual Legal Notice This document contains proprietary information protected by copyright. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Fujitsu Limited. This document is furnished for informational use only, is subject to change without notice, and should not be construed as a commitment by Fujitsu Limited. Fujtsu Limited assumes no responsibility or liability for any errors or inaccuracies that may appear in this document. Copyright 2014 Fujitsu Limited All Rights Reserved Page 2 Copyright 2014 Fujitsu Limited Fujitsu 2.4G Mesh Radio Module And NIC User Manual Trademark Acknowledgements Company names and product names in this manual are trademarks or registered trademarks of respective companies. Note that system names and product names in this manual are not always followed by trademark symbols such as Ⓡ or TM. Page 3 Copyright 2014 Fujitsu Limited Fujitsu 2.4G Mesh Radio Module And NIC User Manual CONTENTS 1. About This Manual................................................................................................... 5 1-1. Covered Product ................................................................................................................ 5 2. Product Description ................................................................................................. 6 2-1. General .............................................................................................................................. 6 2-2. Technology ......................................................................................................................... 6 3. Product Installation And Use ................................................................................... 7 3-1. Installation .......................................................................................................................... 7 3-2. Use ..................................................................................................................................... 7 4. Product Information ................................................................................................. 8 4-1. Technical Specification....................................................................................................... 8 4-2. Regulatory Compliances (EN) ........................................................................................... 8 4-3. Regulatory Compliances (FCC)......................................................................................... 8 4-4. Product Label (Sample) ..................................................................................................... 9 4-5. NIC Block Diagram ............................................................................................................ 9 Page 4 Copyright 2014 Fujitsu Limited Fujitsu 2.4G Mesh Radio Module And NIC User Manual 1. About This Manual 1-1. Covered Product This User Manual contains information on how to install and use Fujitsu 2.4G Mesh Radio Module and Fujitsu 2.4G Mesh Radio NIC (Network Interface Card). Specifically below products are covered. - Part Number WR-H1R0WM1 (Fujitsu Intelligent Society Solution Smart Grid Communications 2.4GHz Mesh Radio Module) - Part Number WR-H2R0WN1 (Fujitsu Intelligent Society Solution Smart Grid Communications 2.4GHz Mesh Radio Interface Card) Page 5 Copyright 2014 Fujitsu Limited Fujitsu 2.4G Mesh Radio Module And NIC User Manual 2. Product Description 2-1. General Fujitsu 2.4G Mesh Radio Module and Fujitsu 2.4G Mesh Radio NIC (Network Interface Card) provide future-proof communications features to smart and advanced multi-functional static single/poly-phase revenue meter from Siemens, IM100 and IM300. The NIC, in an integrated form with IM100/300 as filed replaceable extended communications module, are essential components in Fujitsu Intelligent Society Solution Smart Grid Communications infrastructure solution for electricity, gas and water utility service providers. The Module is integral part of the NIC. 2-2. Technology Fujitsu RF Mesh technology – DFF (Depth-First Forwarding) – is Fujitsu’s wireless ad hoc mesh networking technology which enables autonomous formation of large scale networks and self-healing by application of artificial intelligence. Its scalability and reliability is proven by large utility provider’s deployment of more than one million smart meters in remotely reading power consumptions in real time through the Fujitsu RF Mesh network. DFF is a global standard adopted by IETF (Internet Engineering Task Force) as RFC 6971 and works upon standard wireless media such as IEEE802.11 (Wi-Fi) and conveys standard IPv4/v6 packets with advanced over-the-air security of AES, robust authentication and intrusion prevention mechanism. Most importantly, DFF enables users to enjoy future-proof communications performance. For it heuristically adapts to environment, over-the-air data rate is utilized at maximum so that DFF can perform in ultra-low latency and high bandwidth which are essential to deliver other smart grid applications such as Distribution Automation. Page 6 Copyright 2014 Fujitsu Limited Fujitsu 2.4G Mesh Radio Module And NIC User Manual 3. Product Installation And Use 3-1. Installation Fujitsu 2.4G Mesh Radio NIC is designed to work only with smart and advanced multi-functional static single/poly-phase revenue mete…

Text truncated - open the document above for the full version.

FCC ID: O4D-IC400 Modular Approval Request Letter Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch June 30, 2014 Dear Application Examiner, We, FUJITSU LIMITED, claim that the EUT, FCC ID: O4D-IC400 is a WLAN module and would like to have your authorization as a modular approval specific to the mobile RF exposure condition. The requirements of section 15.212 of FCC rules have been met and shown on the following statements. 1. “The modular transmitter must have its own RF shielding.” The radio portion of this module has been shielded, please see exhibition External Photo. 2. “The modular transmitter must have buffered modulation/data inputs.” The EUT has buffered data input, it is integrated in chip CPU (MAC IC) and POWER IC. 3. “The modular transmitter must have its own power supply regulation.” The part number of this regulator is POWER IC. 4. “The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(C).” The EUT meets the FCC antenna requirements. The spurious emission, unique antenna connector and photo of antennas are shown in the test report. 5. “The modular transmitter must be tested in a stand-alone configuration” The EUT was tested in a stand-alone configuration via a USB extender. Please see section Photographs of Test Configuration in the test report, the EUT was plugged in this extender. 6. “The modular transmitter must be labeled with its own FCC ID number.” Please see exhibition Label Sample for the FCC ID of this module. And also in the exhibition Users Manual, there are instructions give to the OEM on how to label the end product. FCC ID: O4D-IC400 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.” The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are given in the Users Manual. 8. “The modular transmitter must comply with any applicable RF exposure requirements.” The EUT is compliant with all applicable RF exposure requirements. RF Exposure is addressed in the RF exposure exhibition. Please contact me if you have any further question. Thanks for your attention. Best Regards, ____________________________ Daniel Lee Vice President Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch

CONSTRUCTION PHOTOS OF EUT

FCC ID: O4D-IC400 Label Location Front of EUT

SERIAL: 36000001 VERSION: 02A MAC: 00E000DEEC2A DATE: 201426 FCC ID: O4D-IC400 MODEL:Fujitsu 2.4G Mesh Radio NIC

CONSTRUCTION PHOTOS OF EUT

Report No.: SA140604C02 1 of 5 Report Format Version 5.0.0 RF EXPOSURE REPORT REPORT NO.: SA140604C02 MODEL NO.: Fujitsu 2.4G Mesh Radio Module FCC ID: O4D-IC400 RECEIVED: Jun. 04, 2014 TESTED: Jun. 18 ~ Jun. 19, 2014 ISSUED: Jun. 20, 2014 APPLICANT: FUJITSU LIMITED ADDRESS: Kyusyu R&D Center, 2-1, Momochihama 2-chome, Sawara-ku, Fukuoka-shi, Fukuoka-ken, 814-8588, JAPAN ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-com pliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: SA140604C02 2 of 5 Report Format Version 5.0.0 TABLE OF CONTENTS RELEASE CONTROL RECORD ................................................................................................................ 3 1. CERTIFICATION ............................................................................................................................ 4 2. RF EXPOSURE ............................................................................................................................. 5 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) ....................................................... 5 2.2 MPE CALCULATION FORMULA .................................................................................................. 5 2.3 CLASSIFICATION.......................................................................................................................... 5 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER ................................................ 5 Report No.: SA140604C02 3 of 5 Report Format Version 5.0.0 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA140604C02 Original release Jun. 20, 2014 Report No.: SA140604C02 4 of 5 Report Format Version 5.0.0 1. CERTIFICATION PRODUCT: WisReed Module MODEL NO.: Fujitsu 2.4G Mesh Radio Module BRAND: FUJITSU APPLICANT: FUJITSU LIMITED TESTED: Jun. 18 ~ Jun. 19, 2014 TEST SAMPLE: ENGINEERING SAMPLE STANDARDS: FCC Part 2 (Section 2.1091) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 The above equipment (model: Fujitsu 2.4G Mesh Radio Module) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE :Jun. 20, 2014 Ivy Lin / Specialist APPROVED BY : , DATE :Jun. 20, 2014 Ken Liu / Senior Manager Report No.: SA140604C02 5 of 5 Report Format Version 5.0.0 2. RF EXPOSURE 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY (mW/cm 2 ) AVERAGE TIME (minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 2.2 MPE CALCULATION FORMULA Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm 2.3 CLASSIFICATION The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER MODE MAX POWER (dBm) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/cm 2 ) LIMIT (mW/cm 2 ) 1TX 28.33 3.12 20 0.278 1 2TX 28.12 5.48 20 0.456 1 NOTE: For 2TX: Directional gain = 10 log[(10 G1 /20 + 10 G2 /20 + ... + 10 GN /20 ) 2 /N ANT ]= 5.48 dBi ---END---

Report No.: RF140604C02 1 of 82 Report Format Version 5.2.0 FCC TEST REPORT REPORT NO.: RF140604C02 MODEL NO.: Fujitsu 2.4G Mesh Radio Module FCC ID: O4D-IC400 RECEIVED: Jun. 04, 2014 TESTED: Jun. 18 ~ Jun. 19, 2014 ISSUED: Jun. 20, 2014 APPLICANT: FUJITSU LIMITED ADDRESS: Kyusyu R&D Center, 2-1, Momochihama 2-chome, Sawara-ku, Fukuoka-shi, Fukuoka-ken, 814-8588, JAPAN ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-com pliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF140604C02 2 of 82 Report Format Version 5.2.0 TABLE OF CONTENTS RELEASE CONTROL RECORD ................................................................................................................ 4 1. CERTIFICATION ............................................................................................................................ 5 2. SUMMARY OF TEST RESULTS ................................................................................................... 6 2.1 MEASUREMENT UNCERTAINTY ................................................................................................ 6 3. GENERAL INFORMATION ............................................................................................................ 7 3.1 GENERAL DESCRIPTION OF EUT .............................................................................................. 7 3.2 DESCRIPTION OF TEST MODES ................................................................................................ 8 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ................................................ 9 3.3 DUTY CYCLE OF TEST SIGNAL ................................................................................................ 12 3.4 DESCRIPTION OF SUPPORT UNITS ........................................................................................ 14 3.4.1 CONFIGURATION OF SYSTEM UNDER TEST ......................................................................... 14 3.5 GENERAL DESCRIPTION OF APPLIED STANDARDS ............................................................. 15 4. TEST TYPES AND RESULTS ..................................................................................................... 16 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT ..................................................... 16 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT ................................... 16 4.1.2 TEST INSTRUMENTS ................................................................................................................. 17 4.1.3 TEST PROCEDURES ................................................................................................................. 18 4.1.4 DEVIATION FROM TEST STANDARD ....................................................................................... 18 4.1.5 TEST SETUP ............................................................................................................................... 19 4.1.6 EUT OPERATING CONDITIONS ................................................................................................ 20 4.1.7 TEST RESULTS .......................................................................................................................... 21 4.2 CONDUCTED EMISSION MEASUREMENT .............................................................................. 46 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ........................................................... 46 4.2.2 TEST INSTRUMENTS ................................................................................................................. 46 4.2.3 TEST PROCEDURES ................................................................................................................. 47 4.2.4 DEVIATION FROM TEST STANDARD ....................................................................................... 47 4.2.5 TEST SETUP ............................................................................................................................... 47 4.2.6 EUT OPERATING CONDITIONS ................................................................................................ 47 4.2.7 TEST RESULTS .......................................................................................................................... 48 4.3 6dB BANDWIDTH MEASUREMENT .......................................................................................... 50 4.3.…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST 2 3 RADIATED EMISSION TEST 4