O5OGD-W809N802.11b/g/n DEVICE DESCRIPTION: 150Mbps WIRELESS ADSL2/2+ ROUTER

GD-W809N 1 1. Packing List Wireless router x1 Power adapter (DC) x1 ADSL splitter x 1 Quick Installation Guide x1 RJ45 Cable x1 RJ11 Cable x1 CD x1(user manual) Warranty card X1 2. Installing your wireless Router Step 1 Connect the ADSL interface of the device and the Modem interface of the splitter through a telephone cable. Connect the phone to the Phone interface of the splitter through a cable. Connect the incoming line to the Line interface of the splitter. The splitter has three interfaces: Line: Connect to a wall phone jack (RJ-11 jack). Modem: Connect to the ADSL jack of the device. Phone: Connect to a telephone set. Step 2 Connect the LAN interface of the device to the network card of the PC through an Ethernet cable (MDI/MDIX). Note: Use twisted-pair cables to connect with the hub or switch. Step 3 Plug one end of the power adapter to the wall outlet and connect the other end to the Power interface of the device. The following figure shows the application diagram for the connection of the router, PC, splitter and the telephone sets, when no telephone set is placed before the splitter. GD-W809N 2 Caution: The power specification is 12V DC, 500 mA. If the power adapter does not match the specification, it may damage the device. 3. Front Panel There are 5 LED indicators on the front panel of the wireless router. By observing their status, you can judge whether the device runs normally. The following table describes the status of LED indicators (from left to right) on the front panel. LED Indicator Color StatusDescription On The initialization of the device is successful. Power Green Off The device is powered off. GD-W809N 3 On Connection between the device and the physical layer of the office is established. Slow Blinks No signal is being detected. ADSL Green Fast Blinks The device is handshaking with the physical layer of the office. On The Internet connection is normal in the routing mode (for example: PPP dial-up is successful), and no Internet data is being transmitted. BlinksInternet data is being transmitted in the routing mode. Green Off The device is in the bridge mode. Internet Red On The Internet connection fails after successful synchronization in the routing mode (for example: PPP dial-up is failed). On The LAN connection is nomal and activated. BlinksData is being transmitted in the LAN or Internet data is being transmitted in the bridge mode. LAN Green Off The LAN interface is not connected. On The connection of WLAN interface is normal. Blink Data is transmitted through the WLAN interface. Wireless Green Off The WLAN connection is not established.. 4. Rear Panel z Power: Power socket, for connecting the power adapter. z LAN: LAN interface (RJ45), for connecting a hub, switch, or computer with network card on LAN. GD-W809N 4 z ADSL: WAN interface (RJ11), for connecting to the ADSL interface or a splitter through a telephone cable. z WLAN: Press the button and hold it for 1 second to enable WLAN. z Reset: For restoring the factory default settings. Note: The Reset button is in a small circular hole on the rear panel. If you want to restore the default settings, please press the Reset button gently 3~6 seconds with a fine needle inserted into the hole and then release the button. The system reboots and returns to the factory default settings. 5. Installation Options Step 1 Open the browser, and enter http://192.168.1.1/ in the IE address bar. Enter the user name (admin, by default) and password (admin, by default) in the login page. Click Login to log in to the main page. Step 2 Click Wizard and then you can follow the on-screen step-by-step instructions to configure the wireless router. You may also configure the router by referring to the User Manual included in the CD-ROM. Shenzhen Landing Electronics Co.,Ltd Address: 3F Block A,BaiyingBuilding,No.1019 Nanhai Road, Nanshan District,Shenzhen,Guangdong, China Post Code:518067 E-Mail: [email protected] Website: http://www.goldwebcn.com 150Mbps Wireless ADSL2/2+ Router GD-W809N QUICK INSTALLATION GUIDE 150

11 22 33 44 55 A A B B C C D D Gan9.8T92A-6 POWER3.3V;1.0V: for RTL8672-VK5V;3.3V;2.5V: for RTL8271B-VR3.3V:for RTL8188CE WIFI RJ45 WIFI 1T1R RTL8188CE RJ11 Transformer Hybrid RTL8271B-VR AFE IF ETH PHY PCI-e SPI FLASH 4Mbyte RTL8672-VK SDRAM32Mbyte RJ45 RTL8303N Y3 17.664MHz Crystal 40MHz Size Document Number Rev Date: Sheet of Design By: Review By: 0.1 B 210 Friday, November 09, 2012 T&W PAGE <Reviewer> Size Document Number Rev Date: Sheet of Design By: Review By: 0.1 B 210 Friday, November 09, 2012 T&W PAGE <Reviewer> Size Document Number Rev Date: Sheet of Design By: Review By: 0.1 B 210 Friday, November 09, 2012 T&W PAGE <Reviewer>

LABEL LOCATION OF GD‐W809N

FCC ID O5OGD-W809N The location of Antenna on the PCB: Antenna

BLOCK DIAGRAM AND THEORY RJ45 RTL8303N POWER 3.3V;1.0V: for RTL8672-VK 5V;3.3V;2.5V: for RTL8271B-VR 3.3V:for RTL8188CE WIFI RJ45 WIFI 1T1R RTL8188CE RJ11 Transformer Hybrid RTL8271B-VR AFE IF ETH PHYPCI-e RTL8672-VK SPI FLASH 4Mbyte SDRAM 32Mbyte The Gan9.8t92b-1 is a high-performance wireless ADSL router, uplink rate up to 1 Mbps and downlink rate up to 24 Mbps. It provides one RJ11 telephone interface, one RJ45 Ethernet interfaces. The telephone interface is used for connecting to the Internet provided by the telecom carrier. The Ethernet interfaces are used for connecting to the computer, through which you can access the Internet. Computers that are connected with the router through the Ethernet interfaces can establish a small local network area (LAN). Those computers can communicate with each other, sharing resources and files. The Gan9.8t92b-1 is an ideal broadband CPE solution for both home users who wish to share high-speed Internet access and small offices that wish to do business on the Internet. The Gan9.8t92b-1 has Web-based graphic user interface (GUI), in which you can easily modify the settings and connect to your ISP. It also provides flow statistics, connection status, and other detailed information. It supports static IP address, dynamic IP address, and PPPoE connection. The Gan9.8t92b-1 is easily upgraded and provides terminal users and ISP with the guarantee of future. Frequency Range 2412MHz~2472MHz: 802.11b; 802.11g; 802.11n(HT20) 2422MHz~2462 MHz: 802.11n(HT40) Channel: Channel with 5MHz step Antenna gain: 2 dBi Type of emission WIFI Modulation type DSSS802.11bOFDM802.11g/n

KB-6160/KB-6160A/KB- 6167 1.6mm V-0ULE123995 S11411.6mm V-0ULE109769 FR4-97/MTC-971.6mm V-0ULE186152 ZD-95(G)F1/ZD- 95(G)F/ZD-95(G)F/ZD- 95(G)F1/ 1.6mm V-0ULE141940 FR-41.6mm V-0ULE213990 KB-6150,KB-6150C,KB- 6160,KB-6160A,KB- 6060A,KB-6160C,KB- 6060C 1.6mm V-0ULE123995 UL UL UL UL UL UL E308512 UL test in team BOBBINT375J 150 ULE59481 UEW130UL XUEW130UL JY312(#)130UL CT 130 UL UL test in team BobbinPM9820V-0ULE41429 Wire2UEW 150 ULE234867 TapeCT/PZ 130 ULE165111 TransformerJA70199ADIP-1.7mm,12pinULtest in team Bobbin T375J 150 ULE59481 Wire2UEW 130 ULE164502 1318-1(a)/1350F-1(b) 130 ULE17385 PZ/WF2902 130 ULE238500 UL UL JINGJIANG YAHUA PRESSURE SENSITIVE GLUE CO L T WIRE TAPE JINGJIANG YAHUA PRESSURE SENSITIVE GLUE CO.,LTD SHENZHEN DAYANG INDUSTRY CO LTD JINGJIANG YAHUA PRESSURE SENSITIVE GLUE CO LTD guangdong Shengyi Sci.Tech Co.,Ltd. SUMITOMO BAKELITE CO LTD ZHUHAI SUNTEK WIRE CO LTD SHENZHEN JINGQUANLI ELECTRONICS CO.,LTD CHANG CHUN PLASTICS CO LTD Tape 210010000240 TAI-I ELECTRIC WIRE & CABLE CO LTD SHUITIAN KINGBOARD MANUFACTURING FACTOR SHUITIAN KINGBOARD MANUFACTURING FACTOR XINGNING JINYAN ELECTRICAL CO.,LTD. SUZHOU MAILADUONA ELECTRIC MATERIAL CO.,LTD 3M COMPANY ELECTRICAL MARKETS DIV (EMD) Grace Electron Corp.(Guangzhou) SHANGHAI NANYA COPPER CLAD LAMINATE CO.LTD SHANDONG JINBAO ELECTRONICS CO LTD

55 44 33 22 11 D D C C B B A A Gan9.8T92A-6 RF PATH A VD33_A VD33 PCIE_CLK_MPCIE_HSIPPCIE_HSOPPCIE_CLK_PPCIE_HSINPCIE_HSONPCIE_RST LED_WIFI VD33 VD15R1 VD15R0 XI VD33 PCIE_RST VD33_A VD15 VD33_A XO VD33 VD33 PCIE_HSON PCIE_HSIN VD15VD12 PCIE_HSIP VD33 VD12 SPS33 VD33 VD33 VD33_A GPIO_4 PCIE_HSOP GPIO_5 PCIE_CLK_MPCIE_CLK_P LED_WIFI GPIO_6 GPIO_7 GPIO_4GPIO_5GPIO_6GPIO_7 VD33_A VD15 XI XO VDD33 PCIE_HSIN 3 PCIE_HSOP 3 PCIE_RST 3 PCIE_HSIP 3 PCIE_CLK_M 3 LED_WIFI 4 PCIE_CLK_P 3 PCIE_HSON 3 40M_clock 3 Size Document Number Rev Date: Sheet of Design By: Review By: 0.1 C 11 11 Friday, November 09, 2012 T&W PAGE sen <Reviewer> Size Document Number Rev Date: Sheet of Design By: Review By: 0.1 C 11 11 Friday, November 09, 2012 T&W PAGE sen <Reviewer> Size Document Number Rev Date: Sheet of Design By: Review By: 0.1 C 11 11 Friday, November 09, 2012 T&W PAGE sen <Reviewer> WC51 MLCC,10uF,M,6.3V,X5R,0805 WC35 22pF WC270u1F WC4410pF WR33 NP WC26 MLCC,105,K,10V,X5R,0402 WC32 220,NP0,0402 WR23 24K,F 21 WC30 104,M,10V,X5R,0402 WC20 10nF WR27NI/24K,F 2 1 WC38 10pF WR34 NP WR13 MLCC,220,J,25V,NP0,0603 WC13 1R5 WC34 MLCC,10uF,M,6.3V,X5R,0805 WC33 220,NP0,0402 WC5010pF 12 WC4010pF WL7 2.2nH 1 2 WC3 10pF WL52.2nH 12 WR25 10K,F,1/16W,0402 2 1 WC21 MLCC,104,M,10V,X5R,0402 WR12 MLCC,220,J,25V,NP0,0603 WC10 105 WC4 105, WC28 10pF WC14 2R7 WC24 MLCC,104,M,10V,X5R,0402 WR21Bead WANT3 12 WC4622pF/0603 WR16 0R,0603 2 1 WC7 1R5 WC110R9 WC69NI/22pF 1 2 WC39 NP WC16 104 WR31 NP WR50R,0603 21 WC37 22pF WR26 ChipR,THKF,0R,J,1/16W,0402 crystal 40MHz XTAL,40MHz,Fund,?à10ppm,15pF,SMD3.2*2.5,4pin,7M40000183 ,TXC 2 14 3 WC2510nF WC5 10uF,M,6.3V,0805 WC2 22uF,M,6.3V,0805 WC12NP WC52 MLCC,104,M,10V,X5R,0402 WC23 MLCC,105,K,10V,X5R,0402 WL3 3n3 1 2 WC6105 WC29 104,M,10V,X5R,0402 WC9 2R7 WC41 NP WR22 10K,F,1/16W,0402 2 1 WR11Bead WC17 MLCC,105,K,10V,X5R,0402 WC8 0u1F WR32 NP WL2 3n3 1 2 WR37 ChipR,THKF,0R,J,1/16W,0402 WC49MLCC,105,K,10V,X5R,0402 WL815nH 12 WR24 NP WC4722pF WC31 105,K,10V,X5R,0402 R T L 8 1 8 8 C E WU2 PAPE[0] 13 RX2G_IP[0] 19 VD15R[0] 18 TX2G_PAON[0] 16 TX2G_PAOP[0] 17 VD33PA[0] 15 TRSWP[0] 14 VD15R[1] 21 LED1 / ANT_SEL_N 24 LED0 / ANT_SEL_P 23 VD33A 25 RETX 26 VD15A 27 VD12A_LDO 28 XI 29 XO 30 CK_BT_40M 31 REFCLK_N // NC 44 V33PCIe 1 BT_STATE 34 BT_PRI 35 VD15D 41 PDn 36 WAKEn // NC 37 CLKREQn // NC 38 VD12D_LDO 40 HSOP // NC 43 HSON // NC 42 PERSTn // NC 39 REFCLK_P // DV12S_LDO 45 HSIN // HSDP 46 HSIP // HSDM 47 VD12S_LDO // NC 48 WL_ACT 32 WL_RX / B15V_VLD 33 TRSWN[0] / LED2 2 VD33IO 3 VDSPS33 4 LX_SPS0 5 GND_SPS0 6 VD12D 7 BT_Suspend 8 GPIO[5] 9 EEDO 10 EEDI 11 EESK 12 GND 49 VD33R 22 RX2G_IN[0] 20 WC70NI/22pF 1 2 WL16.8uH 12 WL4 2.2nH 1 2 WL6 2.7nH 1 2 WANT2 PX-20314-001E-01 23 1 4

FCC ID O5OGD-W809N TEST REPORT Report No.: EM201200354-4 Application No.: ZJ00017974 Client: Shenzhen Landing Electronics Co., Ltd. Address: A409-410 Nanshan Medical Instrument Industry Park,1019# Nanhai Road,Nanshan District,Shenzhen,Guangdong,518067,P.R.China Sample Description: 150Mbps Wireless ADSL2/2+ Router Model: GD-W809N Adding model / FCC ID: O5OGD-W809N Test Specification: FCC Part 15,Subpart C(Section 15.247) Test Date: 2012-07-18 to 09-27 Issue Date: 2012-10-28 Test Result: Pass. Prepared By: Reviewed By: Approved By: Lynn Xiao/ Test Engineer Jane Cao / Technical Assistance Gavin Wu / Manager Date:2012-10-28 Date:2012-10-28 Date:2012-10-28 Other Aspects: / Abbreviations: ok / P = passed; fail / F = failed; n.a. / N = not applicable The test result in this test report refers exclusively to the presented test sample. This report shall not be reproduced except in full, without the written approval of GRGT. GRG Metrology and Test Co., Ltd. Address: 163, Pingyun Road, West of Huangpu Avenue, Guangzhou, Guangdong, P.R. China Tel:+86-20-38699960 Fax:+86-20-38695185 Email: [email protected] http://www.grgtest.com Ver.:1.0 / 01.Jan.2011 Report No.: EM201200354-4 Application No.: ZJ00017974 Page 2 of 133 FCC ID O5OGD-W809N DIRECTIONS OF TEST 1. This station carries out test task according to the national regulation of verifications which can be traced to National Primary Standards and BIPM. 2. The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. 3. If there is any objection concerning the test, the client should inform the laboratory within 15 days from the date of receiving the test report. Report No.: EM201200354-4 Application No.: ZJ00017974 Page 3 of 133 FCC ID O5OGD-W809N Table of Contents TABLE OF CONTENTS .......................................................................................................................................................... 3 1. TEST RESULT SUMMARY ............................................................................................................................................... 5 2. GENERAL DESCRIPTION OF EUT................................................................................................................................. 6 2.1 APPLICANT .................................................................................................................................................................... 6 2.2 MANUFACTURER ......................................................................................................................................................... 6 2.3 BASIC DESCRIPTION OF EQUIPMENT UNDER TEST ............................................................................................. 6 3. LABORATORY AND ACCREDITATIONS ..................................................................................................................... 7 3.1 LABORATORY ............................................................................................................................................................... 7 3.2 ACCREDITATIONS ....................................................................................................................................................... 7 3.3 MEASUREMENT UNCERTAINTY ............................................................................................................................... 7 3.4 LIST OF USED TEST EQUIPMENT AT GRGT ............................................................................................................. 8 4. ANTENNA REQUIREMENT ............................................................................................................................................. 9 5. CONDUCTED EMISSION MEASUREMENT ............................................................................................................... 10 5.1 LIMITS ....................................................................................................................................................................... 10 5.2 TEST PROCEDURES ................................................................................................................................................ 10 5.3 TEST SETUP ............................................................................................................................................................. 11 5.4 TEST RESULTS ......................................................................................................................................................... 12 6. RADIATED ELECTROMAGNETIC DISTURBANCE ................................................................................................. 14 6.1 LIMITS ....................................................................................................................................................................... 14 6.2 TEST PROCEDURES ................................................................................................................................................ 14 6.3 TEST SETUP ............................................................................................................................................................. 15 6.4 TEST RESULTS ......................................................................................................................................................... 17 7. SPURIOUS EMSSION AT ANTENNA PORT ................................................................................................................ 41 7.1 LIMITS ....................................................................................................................................................................... 41 7.2 TEST PROCEDURES .................................................................................................................................…

Text truncated - open the document above for the full version.

TEST SETUP PHOTOS