O76-X7HG2400AIMS

Page 1 of 3 CONFIDENTIAL User Manual and Basic Theory of Operation Product Name: ES10 Communications Module Model Number: ES10 Date Revision Description July 8, 2024 1 • Confirmed that the product is not portable • Confirm use case distance • Transmission schedule and events July 9, 2024 2 • Antenna Location within the dispenser August 8, 2024 3 • Updated according to optimized placement of the U.FL antenna (OBIP) • Added section on FCC Compliance Statements The ES10 communications module is a piece of hardware that provides connectivity and additional functionality to the ES10 Pump assembly (Dispenser). The ES10 Module is responsible for: • Communicating (Relaying) all the dispenser data to the gateway (Telemetry, Properties and Events) • Detecting and communicating the ID of the badged individual triggering a dispense This module mates with the ES10 Integrated Pump Assembly (IPA) to produce the optical alignment necessary to communicate with it via Infra-Red. See Figures 1, 2 below. General Requirements • The ES10 Communications module is not a stand-alone module. It requires an ES10 Sanitizer or Soap dispenser to fulfill its purpose. • The ES10 Communications module is not a wearable or portable device. • Under general use-case conditions, users are expected to be standing at about 2 to 3 ft. of distance from the ES10 Module. This is the average separation between the body of the user and a dispenser unit as a sanitizing event is triggered. Telemetry Schedule and Events The ES10 module will transmit data after: • A dispensing is triggered • Any status change - Open/Close of enclosure or change of sanitizer refill • Any configuration change. • No dispensing, status or configuration change has occurred – timeout set to 15 minutes. Communications Module Technical Data • Batteries: AA x 4 • Nominal Voltage: 6V • Communication Interfaces in the ES10 Module: o Integrated Pump Assembly (IPA) to Comms. Module: Infra-Red – IR (Inbound) o Comms. Module to Gateway: BLE (Outbound) o Comms. Badge to Module: BLE (Inbound) Page 2 of 3 CONFIDENTIAL Location of the Antenna within the Dispenser Note: The dimensions are approximately. Figure 1 - ES10 Communications Module (left) and IPA (Right) Figure 2 - ES10 IPA-Communications Module Assembly Optical Path U.FL Antenna 30mm 30mm 47mm Enclosure Side 45mm 93mm Back Front Antenna 70mm Page 3 of 3 CONFIDENTIAL Internal Positioning of the Antenna The image below shows the positioning of the U.FL antenna as seen from the back of the ES10 comms. Module. Compliance Statements FCC compliance statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 15mm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. End of Document.

UNITED STATES DESIGNATED AGENT LETTER Date: 30-07-2024 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Applicant U.S. designated agent Company Name: Gojo Industries, Inc. Company Name: Gojo Industries, Inc. FRN: 0002945194 FRN: 0002945194 Grantee Code: O76 Contact Name: Aaron Reynolds Contact Name Aaron Reynolds Address: One Gojo Plaza Suite 500 Address: One Gojo Plaza Suite 500 City/Province/Zip: Akron/Ohio/44311 City/Province/Zip: Akron/Ohio/44311 Telephone: 330-255-6000 Telephone: 330-255-6000 Fax: 330-255-6114 Fax: 330-255-6114 Email: [email protected] Email: [email protected] Applicable Equipment: FCC ID: O76-X7HG2400A ATTN: Director of Certification: We, Gojo Industries, Inc. understand and acknowledge the applicants consent and the designated agent’s obligation to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and e-mail of the designated agent listed above. We, Gojo Industries, Inc. acknowledge the applicant’s acceptance of its obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. Print Name: Aaron Reynolds Title: Product Engineering & Commercialization VP Signature: On behalf of Company: Gojo Industries, Inc. Telephone: 330-255-6000 E-mail: [email protected] Print Name: John E Hooker Title: Chief Enterprise Performance Officer Signature: On behalf of Company: Gojo Industries, Inc. Telephone: 330-255-6000 E-mail: [email protected]

Applicant Declaration QSF27-14-04 Rev 1.1 Jan 17, 2024 Page 1 of 2 Original Issue: Jan. 4, 2021 SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Legal Business Name Gojo Industries, Inc. Address One Gojo Plaza Suite 500,Akron,Ohio 44311, United States, FRN 0002945194 Grantee Code O76 FCC ID O76-X7HG2400A Authorized Contact Name Aaron Reynolds Contact Email [email protected] Contact Phone 330-255-6000 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare; a) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. b) in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for: (1) labeling the equipment with the exact FCC ID as specified in this application, (2) compliance statement labeling pursuant to the applicable rules, (3) compliance of the equipment with the applicable technical rules, c) if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCC’s technical requirements. d) in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. e) in accordance with ISO 17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements. (1) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. (2) the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. (3) the Applicant shall, upon request by SGS, at the Applicant’s expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a “party” for these purposes. g) the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Link to the Covered List: Covered List [Gojo Industries, Inc] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. [Gojo Industries, Inc] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant [is not] identified on the Covered list, established pursuant to §1.50002, as an entity producing “covered” equipment. Applicant Signature: Date: 08/14/2024 Print Name: Aaron Reynolds Title: Product Engineering & Commercialization VP Applicant Signature: Date: 08/14/2024 Applicant Declaration QSF27-14-04 Rev 1.1 Jan 17, 2024 Page 2 of 2 Original Issue: Jan. 4, 2021 SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Print Name: John E Hooker Title: Chief Enterprise Performance Officer *NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database

Gojo Industries, Inc. Date: 14-08-2024 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: O76-X7HG2400A To whom it may concern: We, the undersigned, hereby authorize SGS-CSTC Standards Technical Services Co., Ltd. (SGS) to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with Gojo Industries, Inc. This authorization is valid until further written notice from the applicant. Print Name: Aaron Reynolds Title: Product Engineering & Commercialization VP Signature: On behalf of Company: Gojo Industries, Inc. Telephone: 330-255-6000 E-mail: [email protected] Print Name: John E Hooker Title: Chief Enterprise Performance Officer Signature: On behalf of Company: Gojo Industries, Inc. Telephone: 330-255-6000 E-mail: [email protected]

Gojo Industries, Inc. TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: Confidentiality Request regarding application for FCC ID: O76-X7HG2400A LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commission’s rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. SHORT TERM CONFIDENTIALITY（Remark: If necessary, you can choose short-term confidentiality, but it can not exceed 180 days. During the short-term confidentiality period, the products cannot be sold.） Additionally, the applicant requests the following documents be held confidential until the device is marketed or 0 days from the grant date, whichever is less. If the device is marketed within 0 days of the Grant Date, the applicant will notify the TCB per FCC KDB 726920 D01 Confidentiality Request Procedures. Delete any document that is NOT included in your application External Photos Internal Photos Test Setup Photos User manual(s) Sincerely, Print Name: Aaron Reynolds Title: Product Engineering & Commercialization VP Signature: On behalf of Company: Gojo Industries, Inc. Telephone: 330-255-6000 E-mail: [email protected] Print Name: John E Hooker Title: Chief Enterprise Performance Officer Signature: On behalf of Company: Gojo Industries, Inc. Telephone: 330-255-6000 E-mail: [email protected]

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A02 Rev.A/0 Page: 1 of 7 External Photos for SZCR2406002470AT FCC ID: O76-X7HG2400A SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A02 Rev.A/0 Page: 2 of 7 EUT Constructional Details (EUT Photos) PCB antenna version: SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A02 Rev.A/0 Page: 3 of 7 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A02 Rev.A/0 Page: 4 of 7 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A02 Rev.A/0 Page: 5 of 7 PIFA antenna version: SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A02 Rev.A/0 Page: 6 of 7 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A02 Rev.A/0 Page: 7 of 7

Mesh Systems - Confidential 4151240 Upper Level Labeling Requirements 08/20/202404 1/1 1" x 0.75" Polyester label Must be printed using resin ribbon Layout: QR Code: Contains {"ID":"XXXXXXXXXXXX","Model":"gojoes10","Name":" GOJOES10 XXXXXXXXXXXX","PN":"4151240"} with both X referring to the 12 character device BLE Mac address. First (Top) Row: Contains "ES10 MODULE" text in all capital letters Second Row: Contains "8300-575-BLE Rev: X" With X referring to the latest revision of the assembly Third Row: X refers to the 12 character device BLE Mac Address Fourth Row: Contains "FCC ID: O76-X7HG2400A" Fifth (Bottom) Row: Contains "GOJO Industries, Inc." All text uses the following settings Font: Sans Seriff Font Size: 5.5

A B C D A B C D 1 12 2 3 3 4 4 3.20 "WIDTH" 3.34 "HEIGHT" 2.97 "DEPTH" QTY.DESCRIPTIONREV.PART NO.ITEM 4BATTERY "AA"B6200-0901 1FCC LABEL: ES10A8300-059-9202 1PCBA: ES10 MODULEA8300-570-9103 1MODULE SUB-ASSY: ES10B8300-574-XXX4 DATEAPRVD. BYREVISIONECO ECRREV 05-09-2024MRDINITIAL RELEASE93977A APPROVAL SIGNATURES ON FILE DWG. NO. 8300-575-BLE A8300-575-BLEC05/09/24DATE: DECIMALS: X.X = 0.1 .X.XX = 0.01 .X.XXX = 0.005 FRACTIONS: X/XX = 1/32 ANGLES: X.X = 0.5 X.XX = 0.50 REV.DWG. NO.SIZE M.BULLOCKCHKD BY: 1 of 2 DO NOT SCALE 05/06/24DATE: SHEETSCALE 11:32 M.DEGIDIODRAWN BY: ONE GOJO PLAZA, SUITE 500 AKRON, OH 44311 AND IS LOANED UPON CONDITION THAT IT IS NOT TO BE REPRODUCED OR COPIED IN WHOLE OR PART, OR USED FOR FURNISHING INFORMATION TO OTHERS OR FOR ANY OTHER PURPOSE DETRIMENTAL TO THE INTEREST OF GOJO INDUSTRIES, INC. AND WILL BE RETURNED UPON REQUEST GOJO INDUSTRIES, INC. THIS DRAWING IS THE PROPERTY OF TOLERANCES: CONFIDENTIAL ©2024 GOJO Industries, Inc. All Rights Reserved. Released STATE: MODULE ASSY: BLE ES10 TITLE: THIRD ANGLE PROJECTION INTERPRET DRAWING PER ASME Y14.100 UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES Component Specification - MISC. ASSEMBLY SPECIFICATION PROPERTIES Additional Information: REFER TO SUB-COMPONENT/SPECIFICATIONS TSQ Reviwer: PWB 05-13-2024 ASSEMBLY NAME ITEM #4: SUB-ASSEMBLY 8300-575-BLE8300-574-BLK NOTES: 1. PART TO BE FREE OF DIRT, GREASE, OIL OR ANY FOREIGN MATERIAL. 2. CRITICAL TO QUALITY CHECK: 3. ELECTRICAL ASSEMBLY MUST CONFORM WITH IPC-A-610 CLASS 2 4. FOLLOW ESD ASSOCIATION STANDARD ANSI/ESD S6.1 FOR GROUNDING DURING ALL ASSEMBLY STEPS. 5. ALL ESD SENSITIVE COMPONENTS AND PRINTED CIRCUIT BOARDS MUST BE STORED AND TRANSPORTED IN ESD SAFE PACKAGING. 6. WEIGHT: 143 GRAMS SCALE 1:1 1 2 3 4 SCALE 1:1 APPROXIMATE LOCATION OF LABEL CTQCTQ 8300-575-BLE rev A - Approved Jul 30, 2024 2:20:10 PM 8300-575-BLE rev A Rev# A ECO# 93977 - Approved Aug 05, 2024 12:57:36 PM A B C D A B C D 1 12 2 3 3 4 4 DWG. NO. 8300-575-BLE A8300-575-BLE REV.DWG. NO. CONFIDENTIAL ©2024 GOJO Industries, Inc. All Rights Reserved. SHEET 2 of 2 ITEMDESCRIPTIONQTY. 18300-575-BLE (SEA0300)60 2(Vendor Supplied) PolyBag60 3(Vendor Supplied) EPE Insert3 4(Vendor Supplied) Flat EPE Pad1 5(Vendor Supplied) Cardboard Pad2 6(Vendor Supplied) Clear Tape (403-00061)3m 7(Vendor Supplied) Shipper 515x426x282mm1 8(Vendor Supplied) MH Shipping Label (840-00456)2 ITEM NO PART NUMBERQTYDESCRIPTIONNOTES 1 8300-575-BLE_ENVLP1618300-575-BLE_ENVLP1 2 8300-575-BLE_PKG-POLYBAG18300-575-ble_pkg-polybag.prt 3 8300-575-BLE_PKG-EPE-FORM38300-575-ble_pkg-epe-form.prt 4 8300-575-BLE_PKG-EPE-PAD18300-575-ble_pkg-epe-pad.prt 5 8300-575-BLE_PKG-CARDBOARD-PAD28300-575-ble_pkg-cardboard-pad.prt 6 8300-575-BLE_PKG-SHIP-LBL18300-575-ble_pkg-ship-lbl.prt 7 8300-575-BLE_PKG-SHIPPER18300-575-ble_pkg-shipper.prt ITEM NO PART NUMBERQTYDESCRIPTIONNOTES 1 8300-575-BLE_ENVLP1608300-575-BLE_ENVLP1 2 8300-575-BLE_PKG-CARDBOARD-PAD28300-575-ble_pkg-cardboard-pad.prt 3 8300-575-BLE_PKG-EPE-FORM38300-575-ble_pkg-epe-form.prt 4 8300-575-BLE_PKG-EPE-PAD18300-575-ble_pkg-epe-pad.prt 5 8300-575-BLE_PKG-SHIPPER18300-575-ble_pkg-shipper.prt 6 8300-575-BLE_PKG-TAPE18300-575-ble_pkg-tape.prt 8 8300-575-BLE_PKG-SHIP-LBL18300-575-ble_pkg-ship-lbl.prt ITEM NO PART NUMBERQTYDESCRIPTIONNOTES 1 8300-575-BLE_PKG-CARDBOARD-PAD28300-575-ble_pkg-cardboard-pad.prt 2 8300-575-BLE_PKG-EPE-FORM38300-575-ble_pkg-epe-form.prt 3 8300-575-BLE_PKG-EPE-PAD18300-575-ble_pkg-epe-pad.prt 6 8300-575-BLE_PKG-TAPE18300-575-ble_pkg-tape.prt 1. BEFORE ASSEMBLY: 1.1. Production area must be clean of all foreign material and suspect components. All personnel must be trained to handle GOJO product. 2. ASSEMBLY INSTRUCTIONS: 2.1. Place 20 Module assemblies into 20 Polybags. 2.2. Place the bagged assemblies into each cell of the EPE Insert. 2.3. Repeat 2.1 to 2.2 two more times for a total of 3 Inserts. 2.4. Place a EPE Pad on top of the upper EPE Insert. 2.5. Place 1 Cardboard Pad on the bottom and 1 Cardboard Pad on the top as shown. 2.6. Seal the Insert stack with clear tape as shown. 2.7. Erect the shipper. 2.8. Place the Taped Insert stack into the shipper. 2.9. Close the shipper in compliance with National Motor Freight Classification. 2.10. Label the Shipper as shown. 2.11. Code the shipper on one side using the following format: (L)SCXXXXXX YDDD WHERE: SC = SUPPLIER CODE. XXXXXX = DIGITS AND/OR CHARACTERS MAY VARY AND ARE TO HAVE A UNIQUE IDENTIFIER THAT PROVIDES COMPLETE MANUFACTURING HISTORY. YDDD = LAST DIGIT OF YEAR AND JULIAN DATE OF MANUFACTURE (IF APPLICABLE). 3. PALLET ASSEMBLY (Only one lot of product may be placed on a pallet): 3.1. Palletize the cases on the pallet using a consistent pallet pattern. 3.2. Apply stretch wrap and label to the pallet load. STEP 2.1 STEP 2.2 - 2.5 STEP 2.6 - 2.8 BALLOON TABLES - PLEASE LEAVE HERE Polybags not shown for clarity 5 5 4 1 1 3 3 3 2 7 6 8 8300-575-BLE rev A - Approved Jul 30, 2024 2:20:11 PM 8300-575-BLE rev A Rev# A ECO# 93977 - Approved Aug 05, 2024 12:57:36 PM GOJO Industries eSignatures The signatures certify that this document is adequa te to fulfill its intended purpose or requirement. UserName: Tory Thomas (gojo-net\thomast) Title: Date: Monday, 05 August 2024, 12:07 PM Eastern Daylight Time Meaning: QA Reviewer's Approval ================================================ 8300-575-BLE rev A Rev# A ECO# 93977 - Approved Aug 05, 2024 12:57:36 PM

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A03 Rev.A/0 Page: 1 of 4 Internal Photos for SZCR2406002470AT FCC ID: O76-X7HG2400A SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A03 Rev.A/0 Page: 2 of 4 EUT Constructional Details (EUT Photos) PCB antenna version: Antenna SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A03 Rev.A/0 Page: 3 of 4 PIFA antenna version: Antenna SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-A03 Rev.A/0 Page: 4 of 4 - End of the Appendix -

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/1 Report No.: SZCR240600247002 Page: 1 of 11 Keny Xu EMC Laboratory Manager RF EXPOSURE EVALUATION REPORT Application No.: SZCR2406002470AT Applicant: Gojo Industries, Inc. Address of Applicant: One Gojo Plaza Suite 500 991 Akron Ohio 44311 United States Manufacturer: Seacomp Displays, Inc Address of Manufacturer: 1525 Faraday Ave. Suite 200 Carlsbad CA. 92008 USA Factory: Milli-Henry Electronics Co., Ltd. Address of Factory: Room 101, No.79 Juxiang 1st Road, Dalang Town, Dongguan City, Guangdong Province, P.R. China Equipment Under Test (EUT): EUT Name: IMS Model No.: ES10 Trade Mark: PURELL SMARTLINK® FCC ID: O76-X7HG2400A Standard(s) : FCC Rules 47 CFR §2.1093 KDB 447498 D04 interim General RF Exposure Guidance v01 Date of Receipt: 2024-06-27 Date of Test: 2024-07-10 to 2024-07-16 Date of Issue: 2024-07-20 Evaluation Result: Pass* * In the configuration evaluated, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/1 Report No.: SZCR240600247002 Page: 2 of 11 Revision Record Version Chapter Date Modifier Remark 01 2024-07-20 Original Authorized for issue by: Benson Wang/Project Engineer Eric Fu/Reviewer SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/1 Report No.: SZCR240600247002 Page: 3 of 11 2 Contents Page 1 Cover Page ................................................................................................................................................ 1 2 Contents .................................................................................................................................................... 3 3 General Information .................................................................................................................................. 4 3.1 General Description of E.U.T. ............................................................................................................ 4 3.2 General Description of E.U.T. ............................................................................................................ 4 3.3 Separation Distance ........................................................................................................................... 5 3.4 Test Location ...................................................................................................................................... 6 3.5 Test Facility ........................................................................................................................................ 6 3.6 Deviation from Standards ................................................................................................................... 6 3.7 Abnormalities from Standard Conditions ........................................................................................... 6 4 FCC Radiofrequency radiation exposure limits .................................................................................... 7 4.1 Blanket 1 mW Blanket Exemption ...................................................................................................... 7 4.2 MPE-based Exemption ...................................................................................................................... 7 4.3 SAR-based Exemption ....................................................................................................................... 8 5 Measurement and Calculation ............................................................................................................... 11 5.1 Maximum transmit power ................................................................................................................. 11 5.2 RF Exposure Calculation ................................................................................................................. 11 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/1 Report No.: SZCR240600247002 Page: 4 of 11 3 General Information 3.1 General Description of E.U.T. Product Type: Portable device Mobile device Fixed device 3.2 General Description of E.U.T. Power supply: Powered by DC 6V (4 x 1.5V Size "AA" batteries) Operation Frequency: 2402MHz to 2480MHz Bluetooth Version: V5.2 LE Modulation Type: GFSK Number of Channels: 40 Channel Spacing: 2MHz Antenna Type: FPC Antenna & PCB Antenna Antenna Gain: FPC Antenna: 1.1dBi PCB Antenna: 1.29dBi Remark : The information in this section is provided by the applicant or manufacturer, SGS is not liable to the accuracy, suitability, reliability or/and integrity of the information. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/1 Report No.: SZCR240600247002 Page: 5 of 11 3.3 Separation Distance Minimum test separation distance: 15mm Remark: This minimum test separation distance is determined by the smallest distance from the antenna and radiating structures or outer surface of the device, according to the host form factor, exposure conditions and platform requirements, to any part of the body or extremity of a user or bystander. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch SZEMC-TRF-01 Rev. A/1 Report No.: SZCR240600247002 Page: 6 of 11 3.4 Test Location All tests were performed at: SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen Branch No. 1 Workshop, M-10, Middle Section, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China. 518057. Tel: +86 755 2601 2053 Fax: +86 755 2671 0594 No tests were sub-contracted. 3.5 Test Facility The test facility is recognized, certified, or accredited by the following organizations: • A2LA (Certificate No. 3816.01) SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory is accredited by the American Association for Laboratory Accreditation(A2LA). Certificate No. 3816.01. • VCCI (Member No. 1937) The 3m Fully-anechoic chamb…

Text truncated - open the document above for the full version.

1 Part Numbers: 2344657-1, 2344657-2 2344657-3, 2344657-4 2344657-5, 2344657-6 2344657-7, 2344657-8 2344657-9.1-2344657-1 •Wi-Fi 6, also including Wi-Fi 6E new 6GHz band, Bluetooth, ZigBee •Adhesive backing on FPC simplifies mounting within the device •Omnidirectional coverage •No matching components required •Different cable length and connector options available FEATURES & BENEFITS SPECIFICATIONS (Shown as 2344657-1 : Others can vary with different cable lengths.) Frequency Range (MHz)2400-25005150-58755925-7125 VSWR< 2.7:1< 2.1:1 ＜2.1:1 Average Efficiency61%72%66% Peak Gain1.1dBi4.9dBi5.3dBi Average Gain-2.2dB -1.4dB-1.8dB Power Handling10 Watt cw Feed Point Impedance50 ohms unbalanced PolarizationLinear Size35 mm x 8.0 mm x 0.2 mm Weight< 0.8 g MountingAdhesive Tape Mating ConnectorsMHF and MHF4-type, Refer to page 5 Cable (Coaxial)0.81mm and 1.13mm Dia., Refer to page 5 Operating Temperature-40 to +85°C Storage Temperature-40 to +85°C Hazardous MaterialsA certificate of conformance is available from the product page on TE website. Wi-Fi 6/6E TRIPLE BAND EMBEDDED ANTENNA DATA AND DEVICES /// WI-FI 6/ 6E TRIPLE BAND EMBEDDED ANTENNA 2 P/N Cable Length (mm) Connector RF DATA VSWR(MHz) 2400- 2500 5150- 5875 5925- 7125 2344657-150MHF VSWR< 2.7:1< 2.1:1 ＜2.1:1 Aver. Eff.61%72%66% Peak Gain1.1dBi4.9dBi5.3dBi Aver. Gain-2.2dB-1.4dB-1.8dB 2344657-2100MHF VSWR< 1.3:1< 1.8:1< 1.9:1 Aver. Eff. 586962 Peak Gain 1.04.75.1 Aver. Gain -2.3-1.6-2.1 2344657-3150MHF VSWR< 1.4:1< 1.9:1< 2.0:1 Aver. Eff. 566559 Peak Gain 0.84.54.8 Aver. Gain -2.5-1.8-2.3 2344657-4200MHF VSWR< 1.3:1< 1.6:1< 2.2:1 Aver. Eff. 556256 Peak Gain 0.74.24.6 Aver. Gain -2.6-2.1-2.6 RF data for each P/N Wi-Fi 6/ 6E TRIPLE BAND EMBEDDED ANTENNA Standard Antenna Solutions DATA AND DEVICES /// Wi-Fi 6/ 6E TRIPLE BAND EMBEDDED ANTENNA 3 P/N Cable Length (mm) Connector RF DATA VSWR(MHz) 2400- 2500 5150- 5875 5925- 7125 2344657-550MHF4 VSWR< 1.2:1< 1.5:1< 2.1:1 Aver. Eff. 607165 Peak Gain 1.14.85.2 Aver. Gain -2.2-1.5-1.9 2344657-6100MHF4 VSWR< 1.4:1< 1.7:1< 2.1:1 Aver. Eff. 576760 Peak Gain 0.94.54.9 Aver. Gain -2.4-1.8-2.2 2344657-7150MHF4 VSWR< 1.4:1< 1.5:1< 2.1:1 Aver. Eff. 556256 Peak Gain 0.74.34.6 Aver. Gain -2.6-2.1-2.5 2344657-8200MHF4 VSWR< 1.3:1< 1.5:1< 2.1:1 Aver. Eff. 535852 Peak Gain 0.54.04.2 Aver. Gain -2.8-2.3-2.9 2344657-9250MHF VSWR< 1.3:1< 1.5:1< 2.1:1 Aver. Eff. 535952 Peak Gain 0.33.74.0 Aver. Gain -2.8-2.3-2.8 1- 2344657-1300MHF4 VSWR < 2.7:1< 2.0:1< 2.0:1 Aver. Eff. 473124 Peak Gain 0.91.2-1.8 Aver. Gain -3.3-5.1-6.2 RF data for each P/N Wi-Fi 6/ 6E TRIPLE BAND EMBEDDED ANTENNA Standard Antenna Solutions DATA AND DEVICES /// Wi-Fi 6/ 6E TRIPLE BAND EMBEDDED ANTENNA 4 Return Loss VSWR Efficiency RF DATA (Shown as 2344657-1 : Others can vary with different cable lengths.) DATA AN…

Text truncated - open the document above for the full version.