O8F-ROAECDMA/1x EVDO phone with 802.11 b/g and Bluetooth

User Guide Intellectual property notices © 2010 Palm, Inc., a subsidiary of Hewlett-Packard Company. Palm, XXX, Synergy, Touchstone, webOS, and the Palm and XXX logos are among the trademarks or registered trademarks owned by or licensed to Palm, Inc. Microsoft and Outlook are trademarks of the Microsoft group of companies. Exchange ActiveSync Enabled. Facebook ® is a registered trademark of Facebook, Inc. Google and Google Maps are trademarks of Google, Inc. Amazon, Amazon MP3, and the Amazon MP3 logo are trademarks of Amazon.com, Inc. or its affiliates. Quickoffice is a registered trademark of Quickoffice, Inc. All other brand and product names are or may be trademarks of their respective owners. Disclaimer and limitation of liability Palm, Inc. and its suppliers assume no responsibility for any damage or loss resulting from the use of this guide. Palm, Inc. and its suppliers assume no responsibility for any loss or claims by third parties that may arise through the use of this software. Palm, Inc. and its suppliers assume no responsibility for any damage or loss caused by deletion of data as a result of malfunction, dead battery, or repairs. Be sure to make backup copies of all important data on other media to protect against data loss. Patent pending. This product also is licensed under United States patent 6,058,304. Use of this device requires providing a valid email address, mobile phone number, and related information for account setup and activation. A data plan is also required. An unlimited usage data plan is strongly recommended or additional data charges may apply. Open Source License information You can view the Open Source License terms on your phone. Tap the center of the gesture area and then tap the Launcher icon. Swipe left until the PDF View icon appears. Tap PDF View and then tap Open Source Information.pdf. You can also view the file on your computer. Connect your phone to your computer with the USB cable. On your phone, tap USB Drive. On your computer, locate and double-click the removable drive named for your phone. To locate the drive, do the following for your operating system: •Windows Vista/Windows 7: Open Computer. •Windows XP: Open My Computer. •Mac: Open Finder. •Linux (Ubuntu): The drive is displayed on the desktop. •Other Linux distribution: The location of the drive may vary by system. After you open the drive, double-click the file Open Source Information.pdf. Recycling and disposal This symbol indicates that Palm products should be recycled and not be disposed of in unsorted municipal waste. Palm products should be sent to a facility that properly recycles electrical and electronic equipment. For information on environmental programs visit palm.com/environment or recyclewirelessphones.com/. As part of Palm’s corporate commitment to be a good steward of the environment, we strive to use environmentally friendly materials, reduce waste, and develop the highest standards in electronics recycling. v. 1.0 Contents3 Contents Chapter 1Basics 6Get to know your phone 9Set up your phone 9Turn the phone on/off 10Open applications 11Work with applications 12Enter and save information 13Use the menus 14View and respond to notifications 15Find info on your phone Chapter 2Phone 18Make calls 19Receive calls 19Use voicemail 19What can I do during a call? 20Set up and use a Bluetooth ® hands-free device Chapter 3Email and other messages 22Email 23Messaging Chapter 4Contacts, Calendar, and other personal information 28Contacts 30Calendar Chapter 5Photos, videos, and music 32Camera 32Photos 33Videos 33Music Chapter 6 Web and wireless connections 36Wi-Fi 36Web 36Bluetooth ® wireless technology Chapter 7Documents 38PDF View Chapter 8Preferences 40Screen & Lock 40Sounds & Ringtones Chapter 9Learn More 44While using your phone Regulatory and Safety Information Index 4Contents Chapter 1 : Basics5 Basics You’re about to discover the many things about your Palm ® XXX™ phone that will help you better manage your life and have fun, too. As you become more familiar with your phone, you’ll want to personalize the settings and add applications to make it uniquely yours. But first, take the few easy steps in this chapter to set up your phone and get it running. Then learn about the key features that make moving around on your phone and accessing your information easy: gestures, menus, search, notifications, and more. In this chapter 6Get to know your phone 9Set up your phone 9Turn the phone on/off 10Open applications 11Work with applications 12Enter and save information 13Use the menus 14View and respond to notifications 15Find info on your phone 6Chapter1:Basics Get to know your phone Slide out the keyboard •Hold the phone as shown below and gently push up. Front view 1Earpiece 2Touchscreen: Tap and make other gestures directly on the screen. 3Vo l u m e 4Gesture area: Make the back gesture and begin other gestures here. 5Microphone 6Keyboard: See Use the keyboard. 7Charger/microUSB connector 8Connector cap Chapter 1 : Basics7 Keyboard 1Option: Press to enter numbers, punctuation, and symbols that appear above the letters on the keys (see Enter alternate keyboard characters), or to move the cursor. 2Shift: See Enter uppercase letters. 3Space 4Backspace 5Enter: Press to enter a line return (for example, in a memo or in an email message you are composing) or to accept information you entered in a field. 6Sym: Press to enter symbols and accented characters that don't appear on the keys. To u c h s c r e e n 1Application name: Displays the name of the currently open application. Drag down over the app name to open the application menu. 2Launcher: See Open an application in the Launcher. 3Scroll arrow: Swipe up or down to see icons that are on the page but hidden. 4Quick Launch: See Open an application in Quick Launch. 5Connection icons: Show the status of wireless service connections and battery strength . Drag down over the icons to open the connection menu. 6Page indicators: Show how m…

Text truncated - open the document above for the full version.

July 27, 2010 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Attention: Office of Engineering and Technology Applicant: Palm, Inc. FCC ID: O8F-ROAE Dear Examiner, I, the undersigned, hereby authorize Ms. Claire Hoque, Application Examiner of Compliance Engineering Services, Inc., d.b.a. Compliance Certification Services (47173 Benicia Street, Fremont, CA 94538 USA) and hereafter referred to as CCS, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Ms. Claire Hoque of CCS on our behalf shall have the same effect as acts of our own. The authorization from Palm Inc. is valid for 90 days from date of this letter. Sincerely, Helen Zhao Sr. Regulatory Compliance Engineer [email protected] Office: 408-617-6508 Palm, Inc. A subsid iary of Hewlett Packard Company 950 W. Maude Avenue M/S 21R11 Sunnyvale, CA 94085-2801 USA

July 27, 2010 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC ID: O8F-ROAE To Whom It May Concern: Pursuant to the provisions of Sections 0.457 and 0.459 of the Commission’s rules (47 CFR §§ 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Block Diagram Schematic Diagram Theory of Operation Tune-Up Procedure Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachments for 180 days from the date of the Grant of Equipment Authorization: External Photos Internal Photos Test Setup Photos User Manual It is our understanding that all measurement test reports, FCC ID label format and correspondence during certification review process cannot be granted as confidential documents and such information will be available for public review once the grant of equipment authorization is issued. Sincerely, Helen Zhao Sr. Regulatory Compliance Engineer [email protected] Office: 408-617-6508 Palm, Inc. A subsid iary of Hewlett Packard Company 950 W. Maude Avenue M/S 21R11 Sunnyvale, CA 94085-2801 USA

FCC ID and location FCC ID: O8F-ROAE IC: 3905A-ROAE The FCC ID on your Palm phone is located on a label inside the battery compartment.

FCC OET BULLETIN 65 SUPPLEMENT C IC RSS-102 ISSUE 4 SAR EVALUATION REPORT For CDMA/ 1x EVDO Phone with 802.11b/g and Bluetooth MODEL: P102EWW FCC ID: O8F-ROAE IC: 3905A-ROAE REPORT NUMBER: 10U13270-6A ISSUE DATE: August 3, 2010 Prepared for PALM 950 MAUDE AVENUE SUNNYVALE, CA. 94085 UNITED STATES Prepared by COMPLIANCE CERTIFICATION SERVICES 47173 BENICIA STREET FREMONT, CA 94538, U.S.A. TEL: (510) 771-1000 FAX: (510) 661-0888 REPORT NO: 10U13270-6A DATE: August 3, 2010 FCC ID: O8F-ROAE IC: 3905A-ROAE Page 2 of 48 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. Revision History Rev. Issue Date Revisions Revised By -- July 14, 2010 Initial Issue -- A August 3, 2010 Updated some typos in section 9.1 and 9.2 Sunny Shih REPORT NO: 10U13270-6A DATE: August 3, 2010 FCC ID: O8F-ROAE IC: 3905A-ROAE Page 3 of 48 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. TABLE OF CONTENTS 1. ATTESTATION OF TEST RESULTS.................................................................................................. 5 2. TEST METHODOLOGY ...................................................................................................................... 6 3. FACILITIES AND ACCREDITATION.................................................................................................. 6 4. CALIBRATION AND UNCERTAINTY................................................................................................. 7 4.1. MEASURING INSTRUMENT CALIBRATION ............................................................................. 7 4.2. MEASUREMENT UNCERTAINTY .............................................................................................. 8 5. EQUIPMENT UNDER TEST ............................................................................................................... 9 6. SYSTEM SPECIFICATIONS ............................................................................................................. 10 7. LIQUID PARAMETERS CHECK....................................................................................................... 11 7.1. LIQUID CHECK RESULTS FOR 835 MHZ ............................................................................... 12 7.2. LIQUID CHECK RESULTS FOR 1900 MHz ............................................................................. 14 7.3. LIQUID CHECK RESULTS FOR 2450 MHZ ............................................................................. 16 8. SYSTEM VERIFICATION.................................................................................................................. 18 8.1. SYSTEM CHECK RESULTS FOR D835V2 .............................................................................. 19 8.2. SYSTEM CHECK RESULTS FOR D1900V2 ............................................................................ 19 8.3. SYSTEM CHECK RESULTS FOR D2450V2 ............................................................................ 19 9. OUTPUT POWER VERIFICATION ................................................................................................... 20 9.1. CDMA2000 1xRTT .................................................................................................................... 20 9.2. CDMA200 1xEv-Do ................................................................................................................... 22 9.2.1. Release 0 (Rel. 0)..............................................................................................................22 9.2.2. Revision A (Rev. A) ........................................................................................................... 23 9.3. WIFI RF OUTPUT POWER....................................................................................................... 24 10. KDB 941225 TEST REDUCTION CONSIDERATION.................................................................. 25 11. SUMMARY OF TEST RESULTS.................................................................................................. 27 11.1. HEAD SAR ................................................................................................................................ 27 11.1.1. Left hand side for (LHS) Cellular band .............................................................................. 27 11.1.2. Left hand side (LHS) for PCS band ................................................................................... 27 11.1.3. Right hand side (RHS) for Cellular band ........................................................................... 28 11.1.4. Right hand side (RHS) for PCS band ................................................................................ 28 11.2. BODY SAR................................................................................................................................ 29 11.2.1. Cellular band with 15 mm separation distance.................................................................. 29 REPORT NO: 10U13270-6A DATE: August 3, 2010 FCC ID: O8F-ROAE IC: 3905A-ROAE Page 4 of 48 COMPLIANCE CERTIFICATION SERVICES FORM NO: CCSUP4031B 47173 BENICIA STREET, FREMONT, CA 94538, USA TEL: (510) 771-1000 FAX: (510) 661-0888 This report shall not be reproduced except in full, without the written approval of CCS. 11.2.2. PCS band with 15 mm separation distance....................................................................... 29 11.3. WIFI........................................................................................................................................... 30 11.3.1. Left hand side (RHS) ......................................................................................................... …

Text truncated - open the document above for the full version.

Date/Time: 6/30/2010 9:36:58 AM Test Laboratory: Compliance Certification Services System Performance Check - D835V2 DUT: Dipole 835 MHz; Type: D835V2; Serial: D835V2 - SN:xxx Communication System: CW 835; Frequency: 835 MHz;Duty Cycle: 1:1 Medium parameters used: f = 835 MHz; σ = 0.894 mho/m; ε r = 43; ρ = 1000 kg/m 3 Phantom section: Flat Section Room Ambient Temperature: 24.0 deg. C; Liquid Temperature: 23.0 deg. C DASY4 Configuration: - Area Scan setting - Find Secondary Maximum Within: 2.0 dB and with a peak SAR value greater than 0.0012W/kg - Probe: EX3DV3 - SN3531; ConvF(10.13, 10.13, 10.13); Calibrated: 2/23/2010 - Sensor-Surface: 3mm (Mechanical Surface Detection) - Electronics: DAE3 Sn500; Calibrated: 9/15/2009 - Phantom: SAM 2 (Twin); Type: SAM 2; Serial: 1050 - Measurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 186 d=15mm, Pin=100 mW/Area Scan (7x9x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 1.14 mW/g d=15mm, Pin=100 mW/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 36.4 V/m; Power Drift = -0.200 dB Peak SAR (extrapolated) = 1.45 W/kg SAR(1 g) = 0.970 mW/g; SAR(10 g) = 0.637 mW/g Maximum value of SAR (measured) = 1.13 mW/g Date/Time: 6/30/2010 9:54:53 AM Test Laboratory: Compliance Certification Services System Performance Check - D835V2 DUT: Dipole 835 MHz; Type: D835V2; Serial: D835V2 - SN:xxx Communication System: CW 835; Frequency: 835 MHz;Duty Cycle: 1:1 d=15mm, Pin=100 mW/Z Scan (1x1x34): Measurement grid: dx=20mm, dy=20mm, dz=3mm Maximum value of SAR (measured) = 1.13 mW/g Date/Time: 6/29/2010 12:18:44 PM Test Laboratory: Compliance Certification Services System Performance Check - D1900V2 DUT: Dipole; Type: D1900V2; Serial: 5d043 Communication System: System Check Signal - CW; Frequency: 1900 MHz;Duty Cycle: 1:1 Medium parameters used: f = 1900 MHz; σ = 1.41 mho/m; ε r = 41.2; ρ = 1000 kg/m 3 Phantom section: Flat Section Room Ambient Temperature: 24.0 deg. C; Liquid Temperature: 23.0 deg. C DASY4 Configuration: - Area Scan setting - Find Secondary Maximum Within: 2.0 dB and with a peak SAR value greater than 0.0012W/kg - Probe: EX3DV3 - SN3531; ConvF(8.64, 8.64, 8.64); Calibrated: 2/23/2010 - Sensor-Surface: 3mm (Mechanical Surface Detection) - Electronics: DAE3 Sn500; Calibrated: 9/15/2009 - Phantom: SAM 2 (Twin); Type: SAM 2; Serial: 1050 - Measurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 186 d=10mm, Pin=100mW/Area Scan (7x7x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 3.93 mW/g d=10mm, Pin=100mW/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 58.4 V/m; Power Drift = -0.074 dB Peak SAR (extrapolated) = 7.00 W/kg SAR(1 g) = 3.82 mW/g; SAR(10 g) = 2.01 mW/g Maximum value of SAR (measured) = 4.81 mW/g Date/Time: 6/29/2010 12:35:19 PM Test Laboratory: Compliance Certification Services System Performance Check - D1900V2 DUT: Dipole; Type: D1900V2; Serial: 5d043 Communication System: System Check Signal - CW; Frequency: 1900 MHz;Duty Cycle: 1:1 d=10mm, Pin=100mW/Z Scan (1x1x34): Measurement grid: dx=20mm, dy=20mm, dz=3mm Maximum value of SAR (measured) = 4.79 mW/g Date/Time: 7/6/2010 10:57:03 AM Test Laboratory: Compliance Certification Services System Performance Check - D2450V2 DUT: Dipole ; Type: D2450V2; Serial: 706 Communication System: System Check Signal - CW; Frequency: 2450 MHz;Duty Cycle: 1:1 Medium parameters used: f = 2450 MHz; σ = 1.97 mho/m; ε r = 52.7; ρ = 1000 kg/m 3 Phantom section: Flat Section Room Ambient Temperature: 24.0 deg. C; Liquid Temperature: 23.0 deg. C DASY4 Configuration: - Area Scan setting - Find Secondary Maximum Within: 2.0 dB and with a peak SAR value greater than 0.0012W/kg - Probe: EX3DV3 - SN3531; ConvF(7.58, 7.58, 7.58); Calibrated: 2/23/2010 - Sensor-Surface: 3mm (Mechanical Surface Detection) - Electronics: DAE3 Sn500; Calibrated: 9/15/2009 - Phantom: Flat Phantom ELI4.0; Type: QDOVA001BA; Serial: SN:1003 - Measurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 186 d=10mm, Pin=100mW/Area Scan (7x7x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 6.88 mW/g d=10mm, Pin=100mW/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 59.5 V/m; Power Drift = 0.016 dB Peak SAR (extrapolated) = 10.9 W/kg SAR(1 g) = 5.4 mW/g; SAR(10 g) = 2.52 mW/g Maximum value of SAR (measured) = 7.14 mW/g Date/Time: 7/6/2010 11:14:17 AM Test Laboratory: Compliance Certification Services System Performance Check - D2450V2 DUT: Dipole ; Type: D2450V2; Serial: 706 Communication System: System Check Signal - CW; Frequency: 2450 MHz;Duty Cycle: 1:1 d=10mm, Pin=100mW/Z Scan (1x1x34): Measurement grid: dx=20mm, dy=20mm, dz=3mm Maximum value of SAR (measured) = 7.11 mW/g

Date/Time: 6/30/2010 3:24:13 PM Test Laboratory: Compliance Certification Services CELL Band_Left Hand Side_open DUT: Palm; Type: N/A; Serial: N/A Communication System: CDMA; Frequency: 824.7 MHz;Duty Cycle: 1:1 Medium parameters used: f = 825 MHz; σ = 0.883 mho/m; ε r = 43.1; ρ = 1000 kg/m 3 Phantom section: Left Section Room Ambient Temperature: 24.0 deg. C; Liquid Temperature: 23.0 deg. C DASY4 Configuration: - Area Scan setting - Find Secondary Maximum Within: 2.0 dB and with a peak SAR value greater than 0.0012W/kg - Probe: EX3DV3 - SN3531; ConvF(10.13, 10.13, 10.13); Calibrated: 2/23/2010 - Sensor-Surface: 3mm (Mechanical Surface Detection) - Electronics: DAE3 Sn500; Calibrated: 9/15/2009 - Phantom: SAM 2 (Twin); Type: SAM 2; Serial: 1050 - Measurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 186 Touch_L-ch/Area Scan (7x11x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 0.949 mW/g Touch_L-ch/Zoom Scan (7x7x9)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=3mm Reference Value = 32.3 V/m; Power Drift = -0.037 dB Peak SAR (extrapolated) = 1.10 W/kg SAR(1 g) = 0.870 mW/g; SAR(10 g) = 0.649 mW/g Maximum value of SAR (measured) = 0.959 mW/g Date/Time: 6/30/2010 3:00:17 PM Test Laboratory: Compliance Certification Services CELL Band_Left Hand Side_open DUT: Palm; Type: N/A; Serial: N/A Communication System: CDMA; Frequency: 836.52 MHz;Duty Cycle: 1:1 Medium parameters used (interpolated): f = 836.52 MHz; σ = 0.896 mho/m; ε r = 43; ρ = 1000 kg/m 3 Phantom section: Left Section Room Ambient Temperature: 24.0 deg. C; Liquid Temperature: 23.0 deg. C DASY4 Configuration: - Area Scan setting - Find Secondary Maximum Within: 2.0 dB and with a peak SAR value greater than 0.0012W/kg - Probe: EX3DV3 - SN3531; ConvF(10.13, 10.13, 10.13); Calibrated: 2/23/2010 - Sensor-Surface: 3mm (Mechanical Surface Detection) - Electronics: DAE3 Sn500; Calibrated: 9/15/2009 - Phantom: SAM 2 (Twin); Type: SAM 2; Serial: 1050 - Measurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 186 Touch_M-ch/Area Scan (7x11x1): Measurement grid: dx=15mm, dy=15mm Info: Interpolated medium parameters used for SAR evaluation. Maximum value of SAR (measured) = 0.978 mW/g Touch_M-ch/Zoom Scan (7x7x9)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=3mm Reference Value = 32.6 V/m; Power Drift = -0.198 dB Peak SAR (extrapolated) = 1.21 W/kg SAR(1 g) = 0.962 mW/g; SAR(10 g) = 0.714 mW/g Info: Interpolated medium parameters used for SAR evaluation. Maximum value of SAR (measured) = 1.05 mW/g Date/Time: 6/30/2010 3:48:02 PM Test Laboratory: Compliance Certification Services CELL Band_Left Hand Side_open DUT: Palm; Type: N/A; Serial: N/A Communication System: CDMA; Frequency: 848.31 MHz;Duty Cycle: 1:1 Medium parameters used (interpolated): f = 848.31 MHz; σ = 0.908 mho/m; ε r = 42.8; ρ = 1000 kg/m 3 Phantom section: Left Section Room Ambient Temperature: 24.0 deg. C; Liquid Temperature: 23.0 deg. C DASY4 Configuration: - Area Scan setting - Find Secondary Maximum Within: 2.0 dB and with a peak SAR value greater than 0.0012W/kg - Probe: EX3DV3 - SN3531; ConvF(10.13, 10.13, 10.13); Calibrated: 2/23/2010 - Sensor-Surface: 3mm (Mechanical Surface Detection) - Electronics: DAE3 Sn500; Calibrated: 9/15/2009 - Phantom: SAM 2 (Twin); Type: SAM 2; Serial: 1050 - Measurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 186 Touch_H-ch/Area Scan (7x11x1): Measurement grid: dx=15mm, dy=15mm Info: Interpolated medium parameters used for SAR evaluation. Maximum value of SAR (measured) = 0.989 mW/g Touch_H-ch/Zoom Scan (7x7x9)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=3mm Reference Value = 32.6 V/m; Power Drift = 0.142 dB Peak SAR (extrapolated) = 1.22 W/kg SAR(1 g) = 0.931 mW/g; SAR(10 g) = 0.692 mW/g Info: Interpolated medium parameters used for SAR evaluation. Maximum value of SAR (measured) = 1.02 mW/g Date/Time: 6/30/2010 1:40:53 PM Test Laboratory: Compliance Certification Services CELL Band_Left Hand Side_close DUT: Palm; Type: N/A; Serial: N/A Communication System: CDMA; Frequency: 824.7 MHz;Duty Cycle: 1:1 Medium parameters used: f = 825 MHz; σ = 0.883 mho/m; ε r = 43.1; ρ = 1000 kg/m 3 Phantom section: Left Section Room Ambient Temperature: 24.0 deg. C; Liquid Temperature: 23.0 deg. C DASY4 Configuration: - Area Scan setting - Find Secondary Maximum Within: 2.0 dB and with a peak SAR value greater than 0.0012W/kg - Probe: EX3DV3 - SN3531; ConvF(10.13, 10.13, 10.13); Calibrated: 2/23/2010 - Sensor-Surface: 3mm (Mechanical Surface Detection) - Electronics: DAE3 Sn500; Calibrated: 9/15/2009 - Phantom: SAM 2 (Twin); Type: SAM 2; Serial: 1050 - Measurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 186 Touch_L-ch/Area Scan (7x11x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 0.799 mW/g Touch_L-ch/Zoom Scan (7x7x9)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=3mm Reference Value = 30.4 V/m; Power Drift = 0.093 dB Peak SAR (extrapolated) = 1.01 W/kg SAR(1 g) = 0.760 mW/g; SAR(10 g) = 0.561 mW/g Maximum value of SAR (measured) = 0.836 mW/g Date/Time: 6/30/2010 1:16:06 PM Test Laboratory: Compliance Certification Services CELL Band_Left Hand Side_close DUT: Palm; Type: N/A; Serial: N/A Communication System: CDMA; Frequency: 836.52 MHz;Duty Cycle: 1:1 Medium parameters used (interpolated): f = 836.52 MHz; σ = 0.896 mho/m; ε r = 43; ρ = 1000 kg/m 3 Phantom section: Left Section Room Ambient Temperature: 24.0 deg. C; Liquid Temperature: 23.0 deg. C DASY4 Configuration: - Area Scan setting - Find Secondary Maximum Within: 2.0 dB and with a peak SAR value greater than 0.0012W/kg - Probe: EX3DV3 - SN3531; ConvF(10.13, 10.13, 10.13); Calibrated: 2/23/2010 - Sensor-Surface: 3mm (Mechanical Surface Detection) - Electronics: DAE3 Sn500; Calibrated: 9/15/2009 - Phantom: SAM 2 (Twin); Type: SAM 2; Serial: 1050 - Measurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 186 Touch_M-ch/Area Scan (7x11x1): Measurement g…

Text truncated - open the document above for the full version.

Date/Time: 6/29/2010 6:16:09 PM Test Laboratory: Compliance Certification Services PCS Band_Left Hand Side_open DUT: Palm; Type: N/A; Serial: N/A Communication System: CDMA PCS band; Frequency: 1880 MHz;Duty Cycle: 1:1 Medium parameters used: f = 1880 MHz; σ = 1.39 mho/m; ε r = 41.2; ρ = 1000 kg/m 3 Phantom section: Left Section Room Ambient Temperature: 24.0 deg. C; Liquid Temperature: 23.0 deg. C DASY4 Configuration: - Area Scan setting - Find Secondary Maximum Within: 2.0 dB and with a peak SAR value greater than 0.0012W/kg - Probe: EX3DV3 - SN3531; ConvF(8.64, 8.64, 8.64); Calibrated: 2/23/2010 - Sensor-Surface: 3mm (Mechanical Surface Detection) - Electronics: DAE3 Sn500; Calibrated: 9/15/2009 - Phantom: SAM 2 (Twin); Type: SAM 2; Serial: 1050 - Measurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 186 Touch_M-ch/Area Scan (7x11x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 0.679 mW/g Touch_M-ch/Zoom Scan (7x7x9)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=3mm Reference Value = 22.3 V/m; Power Drift = -0.099 dB Peak SAR (extrapolated) = 0.883 W/kg SAR(1 g) = 0.590 mW/g; SAR(10 g) = 0.369 mW/g Maximum value of SAR (measured) = 0.690 mW/g Date/Time: 6/29/2010 5:09:07 PM Test Laboratory: Compliance Certification Services PCS Band_Left Hand Side_close DUT: Palm; Type: N/A; Serial: N/A Communication System: CDMA PCS band; Frequency: 1880 MHz;Duty Cycle: 1:1 Medium parameters used: f = 1880 MHz; σ = 1.39 mho/m; ε r = 41.2; ρ = 1000 kg/m 3 Phantom section: Left Section Room Ambient Temperature: 24.0 deg. C; Liquid Temperature: 23.0 deg. C DASY4 Configuration: - Area Scan setting - Find Secondary Maximum Within: 2.0 dB and with a peak SAR value greater than 0.0012W/kg - Probe: EX3DV3 - SN3531; ConvF(8.64, 8.64, 8.64); Calibrated: 2/23/2010 - Sensor-Surface: 3mm (Mechanical Surface Detection) - Electronics: DAE3 Sn500; Calibrated: 9/15/2009 - Phantom: SAM 2 (Twin); Type: SAM 2; Serial: 1050 - Measurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 186 Touch_M-ch/Area Scan (7x11x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 0.589 mW/g Touch_M-ch/Zoom Scan (7x7x9)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=3mm Reference Value = 19.9 V/m; Power Drift = 0.146 dB Peak SAR (extrapolated) = 1.06 W/kg SAR(1 g) = 0.639 mW/g; SAR(10 g) = 0.364 mW/g Maximum value of SAR (measured) = 0.773 mW/g Date/Time: 6/29/2010 6:42:24 PM Test Laboratory: Compliance Certification Services PCS Band_Left Hand Side_open DUT: Palm; Type: N/A; Serial: N/A Communication System: CDMA PCS band; Frequency: 1880 MHz;Duty Cycle: 1:1 Medium parameters used: f = 1880 MHz; σ = 1.39 mho/m; ε r = 41.2; ρ = 1000 kg/m 3 Phantom section: Left Section Room Ambient Temperature: 24.0 deg. C; Liquid Temperature: 23.0 deg. C DASY4 Configuration: - Area Scan setting - Find Secondary Maximum Within: 2.0 dB and with a peak SAR value greater than 0.0012W/kg - Probe: EX3DV3 - SN3531; ConvF(8.64, 8.64, 8.64); Calibrated: 2/23/2010 - Sensor-Surface: 3mm (Mechanical Surface Detection) - Electronics: DAE3 Sn500; Calibrated: 9/15/2009 - Phantom: SAM 2 (Twin); Type: SAM 2; Serial: 1050 - Measurement SW: DASY4, V4.7 Build 80; Postprocessing SW: SEMCAD, V1.8 Build 186 Tilt_M-ch/Area Scan (7x11x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = 0.491 mW/g Tilt_M-ch/Zoom Scan (7x7x9)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=3mm Reference Value = 18.8 V/m; Power Drift = -0.027 dB Peak SAR (extrapolated) = 0.624 W/kg SAR(1 g) = 0.434 mW/g; SAR(10 g) = 0.277 mW/g Maximum value of SAR (measured) = 0.502 mW/g Date/Time: 6/29/2010 5:36:05 PM Test Laboratory: Compliance Certification Services PCS Band_Left Hand Side_close DUT: Palm; Type: N/A; Serial: N/A Communication System: CDMA PCS band; Frequency: 1880 MHz;Duty Cycle: 1:1 Medium parameters used: f = 1880 MHz; σ = 1.39 mho/m; ε r = 41.2; ρ = 1000 kg/m 3 Phantom section: Left Section Room Ambient Temperature: 24.0 deg. C; Liquid Temperature: 23.0 deg. C DASY4 Configuration: - Area Scan setting - Find Secondary Maximum Within: 2.0 dB and with a peak SAR value greater than 0.0012W/kg - Probe: EX3DV3 - SN3531; ConvF(8.64…

Text truncated - open the document above for the full version.