O8H-ELLIX40BPOS PRINTER

OPERATOR’S Manual All specifications are subject to change without notice Warning - U.S. This equipment has been tested and founded to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. In case, Operation of this equipment in a residential area is likely to cause harmful interference to radio communications. the user will be required to correct the interference at his own expense. Notice - Canada This Apparatus complies with class “A” limits for radio interference as specified in the Canadian department of communications radio interference regulations. Get appareil est conforme aux normes class “A” d’interference radio tel que specifier par ministre canadien des communications dans les reglements d’interference radio. Warning This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. FCC compliance Information (for WLAN and BLUETOOTH) This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Information to the user [NOTE] This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. [IMPORTANT NOTE] FCC RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20centimeters between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Caution Some semiconductor devices are easily damaged by static electricity. You should turn the printer “OFF”, before you connect or remove the cables on the rear side, in order to guard the printer against the static electricity. If the printer is damaged by the static electricity, you should turn the printer “OFF” and contact your dealer for assistance. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment. INTRODUCTION The ELLIX 30/40 Roll Printer is designed for use with electronic instruments such as system ECR, POS, banking equipment, computer peripheral equipment, etc. The main features of the printer are as follows: 1. High speed printing : 220mm/s(ELLIX40), 180mm/s(ELLIX30), 52 lines per second( 12X24 Font, 220m/s) 2. Low noise thermal printing. 3. Support a variety of interfaces : USB default ELLIX30: USB+RS-232(Serial) / USB+IEEE1284 / USB+WLAN / USB+ETHERNET+RS-233(Serial) ELLIX40: USB Only / USB+RS-232(Serial) / USB+IEEE1284 / USB+ETHERNET USB+WLAN / USB+Bluetooth / USB+ETHERNET+RS-232(Serial) 4. Jam free (Implementation of automatic return of Cutter Jam) 5. Characters can be scaled up to 64 times compared to it’s original size. 6. The data buffer allows the unit to receive print data even during printing. 7. Bar code printing is possible by using a bar code command. 8. Different print densities can be selected by DIP switches. 9. Peripheral units drive circuit enables control of external devices such as cash drawer. 10. 2-dimantional bar code(PDF-417) and Two color printing. Please be sure to read the instruction in this manual carefully before using ELLIX30/40. LEGISLATION AND WEEE SYMBOL 2002/96/CE Waste Electrical and Electronic Equipment Directive on the treatment, collection, recycling and disposal of electric and electronic devices and their components. The crossed dustbin symbol on the device means that it should not be disposed of with other household wastes at the end of its working life. Instead, the device should be taken to the waste collection centres for activation of the treatment, collection, recycling and disposal procedure. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal 1.ELLIX 30 2.ELLIX 40 - 1 - Table of Contents CHAPTER 1. SETTING UP THE PRINTER ..................................... 2 …

Text truncated - open the document above for the full version.

Rev 11/20/07 222-2, Sinneung-Ri, Seowun-Myeon, Anseong-City, Gyeonggi-Do, 456-853, Korea Tel No : +82-2-2101-9672 Fax No : +82-2-2101-9691 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: O8H-ELLIX40B Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Exhibit Type File Name Block Diagram Schematics Parts List Operational description Block Diagram (O8H-ELLIX40B).pdf Schematics (O8H-ELLIX40B).pdf Part List (O8H-ELLIX40B).pdf Operational Description (O8H-ELLIX40B).pdf The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Pursuant to DA04-1705 June 15, 2004 of the Commission’s public notice, we also request temporary confidential treatment of information accompanying this application as outlined below: Exhibit Type File Name - - Sincerely, Byoungjo-Ha / Chief Engineer Shin Heung Precision Co., Ltd.

222-2, Sinneung-Ri, Seowun-Myeon, Anseong-City, Gyeonggi-Do, 456-853, Korea Tel No : +82-2-2101-9672 Fax No : +82-2-2101-9691 ATTESTATION STATEMENT In re : Shin Heung Precision Co., Ltd. FCC ID : O8H-ELLIX40B Date : July 26, 2013 15.247(a)(1) The hopping sequence is random. Each hopping channels is used equally on the average. The receiver input bandwidth matches the bandwidth of the transmitted signal. The receiver has the ability to shift frequencies in synchronization with the transmitted signals. Example of a 79 hopping sequence in data mode: 40, 21, 44, 23, 42, 53, 46, 55, 48, 33, 52, 35, 50, 65, 54, 67, 56, 37, 60, 39, 58, 69, 62, 71, 64, 25, 68, 27, 66, 57, 70, 59, 72, 29, 76, 31, 74, 61, 78, 63, 01, 41, 05, 43, 03, 73, 07, 75, 09, 45, 13, 47, 11, 77, 15, 00, 64, 49, 66, 53, 68, 02, 70, 06, 01, 51, 03, 55, 05, 04 15.247(g) The system is designed to comply with all of the regulations in Section 15.247 when the transmitter is presented with a continuous data (or information). 15.247(h) The system does not coordinate its channel selection/hopping sequence with other frequency hopping systems for the express purpose of avoiding the simultaneous occupancy of individual hopping frequencies by multiple transmitters. Sincerely, Byoungjo-Ha / Chief Engineer Shin Heung Precision Co., Ltd.

CTK Co., Ltd. 386-1, Ho-dong, Cheoin-gu, Yongin-si, Gyeonggi-do, 449-100, Korea Tel: +82-31-339-9970 Fax: +82-31-339-9855 www.e-ctk.com EUT External Photographs CTK Co., Ltd. 386-1, Ho-dong, Cheoin-gu, Yongin-si, Gyeonggi-do, 449-100, Korea Tel: +82-31-339-9970 Fax: +82-31-339-9855 www.e-ctk.com CTK Co., Ltd. 386-1, Ho-dong, Cheoin-gu, Yongin-si, Gyeonggi-do, 449-100, Korea Tel: +82-31-339-9970 Fax: +82-31-339-9855 www.e-ctk.com CTK Co., Ltd. 386-1, Ho-dong, Cheoin-gu, Yongin-si, Gyeonggi-do, 449-100, Korea Tel: +82-31-339-9970 Fax: +82-31-339-9855 www.e-ctk.com Adapter

CTK Co., Ltd. 386-1, Ho-dong, Cheoin-gu, Yongin-si, Gyeonggi-do, 449-100, Korea Tel: +82-31-339-9970 Fax: +82-31-339-9855 www.e-ctk.com Label and Location

CTK Co., Ltd. 386-1, Ho-dong, Cheoin-gu, Yongin-si, Gyeonggi-do, 449-100, Korea Tel: +82-31-339-9970 Fax: +82-31-339-9855 www.e-ctk.com EUT Internal Photographs CTK Co., Ltd. 386-1, Ho-dong, Cheoin-gu, Yongin-si, Gyeonggi-do, 449-100, Korea Tel: +82-31-339-9970 Fax: +82-31-339-9855 www.e-ctk.com Main Board CTK Co., Ltd. 386-1, Ho-dong, Cheoin-gu, Yongin-si, Gyeonggi-do, 449-100, Korea Tel: +82-31-339-9970 Fax: +82-31-339-9855 www.e-ctk.com LCD Board CTK Co., Ltd. 386-1, Ho-dong, Cheoin-gu, Yongin-si, Gyeonggi-do, 449-100, Korea Tel: +82-31-339-9970 Fax: +82-31-339-9855 www.e-ctk.com Sub Board Bluetooth Module CTK Co., Ltd. 386-1, Ho-dong, Cheoin-gu, Yongin-si, Gyeonggi-do, 449-100, Korea Tel: +82-31-339-9970 Fax: +82-31-339-9855 www.e-ctk.com Bluetooth Module CTK Co., Ltd. 386-1, Ho-dong, Cheoin-gu, Yongin-si, Gyeonggi-do, 449-100, Korea Tel: +82-31-339-9970 Fax: +82-31-339-9855 www.e-ctk.com Bluetooth Module_inside Antenna location CTK Co., Ltd. 386-1, Ho-dong, Cheoin-gu, Yongin-si, Gyeonggi-do, 449-100, Korea Tel: +82-31-339-9970 Fax: +82-31-339-9855 www.e-ctk.com Antenna

자 료 종 류 작성 / 심사 / 결정 / 등 록 일 자 Check Check Approval 위니젠 위니젠위니젠 위니젠 Check Check Approval 고객사 고객사고객사 고객사 Part No. Part No. Part No. Part No. W WW W5 55 5I II I- -- -B BB B0 00 0- -- -0 00 07 77 7 (150 mm) (150 mm)(150 mm) (150 mm) (주) (주)(주) (주)위니젠 위니젠위니젠 위니젠 WINiZEN Co. Ltd. 2 겕섚뇊ꖵ 靵닆 사 사사 사 양 양양 양 승 승승 승 인 인인 인 원 원원 원 품 품품 품 명 명명 명 Internal Antenna 모델명 모델명모델명 모델명 업체 업체업체 업체 P/N P/N P/N P/N W5I-BO-07 NO. NO.NO. NO. CODE CODECODE CODE DESCRIPTION DESCRIPTIONDESCRIPTION DESCRIPTION REMARK REMARKREMARK REMARK 1 2.4 GHz Internal Antenna 150 mm 2 3 4 5 6 상기 상기상기 상기 품목의 품목의품목의 품목의 승인을 승인을승인을 승인을 허락하여 허락하여허락하여 허락하여 주시기 주시기주시기 주시기 바랍니다 바랍니다바랍니다 바랍니다. .. . 2012 20122012 2012 년 년년 년 6 66 6 월 월월 월 1 11 15 55 5 일 일일 일 업 체 명 : (주)위니젠 회사주소 : 본사 -대전시 유성구 문지동 103-6 한국과학기술원 ICC 진리관 T205 전 화 : 042-863-8640 F A X : 042-863-8641 시흥공장-경기 시흥시 하상동 377-4 써미트빌 3층 전 화: 031-435-0226 F A X: 031-435-0228 WINiZEN Co. Ltd. 3  목차 목차목차 목차 – 1. 승인원 승인원승인원 승인원 이력 이력이력 이력 List 2. 규격 규격규격 규격 3. 기구 기구기구 기구 도면 도면도면 도면 4. 측정 측정측정 측정 기준 기준기준 기준 41 시험 시험시험 시험 장비 장비장비 장비 42 시험 시험시험 시험 장비 장비장비 장비 Setting 43 Calibration 5. 시험 시험시험 시험 절차 절차절차 절차 51 VSWR 52 이득 이득이득 이득 및 및및 및 방사패턴 방사패턴방사패턴 방사패턴 측정 측정측정 측정 6. 측정 측정측정 측정 Data 61 VSWR 62 S11 63 Radiation Pattern 7. Reliability Test 8. Packaging 9. RoHS Data WINiZEN Co. Ltd. 4 Document No. WAT–1206–EX148I Rev. No. IR Model Name W5IBO07 (150 mm) 1. 승인원 승인원승인원 승인원 이력 이력이력 이력 List 승인원 승인원승인원 승인원 이력 이력이력 이력 List NO 일자 일자일자 일자 변경전 변경전변경전 변경전 변경후 변경후변경후 변경후 사유 사유사유 사유 Rev 1 2012. 6. 15 최초 최초최초 최초 발행 발행발행 발행 IR 2 3 4 5 6 7 8 9 10 11 12 13 14 15 WINiZEN Co. Ltd. 5 Document No. WAT–1206–EX148I Rev. No. IR Model Name W5IBO07 (150 mm) 2. 규격 규격규격 규격 Electrical Specifications Frequency Range 2400 ~ 2483.5 MHz Band Width 83.5 (MHz) V.S.W.R ( Min ) 1.9 :1 Gain Max ) 2 ± 1 dBi Input Impedance 50 (Ω) Polarization Linear Mechanical Specifications Antenna Size 48 x 8 x 1 mm Cable Length 1.13D, 150 mm Radiator Material Copper Operation Temperature -20 ~ 70 (°C) Operation Humidity 10 ~ 90 (%) Option Remarks Data was measured at free space. WINiZEN Co. Ltd. 6 Document No. WAT–1206–EX148I Rev. No. IR Model Name W5IBO07 (150 mm) 3. 기구 기구기구 기구 도면 도면도면 도면 Core 규격: O.D 8mm x I.D 3.4mm x 12mm H WINiZEN Co. Ltd. 7 Document No. WAT–1206–EX148I Rev. No. IR Model Name W5IBO07 (150 mm) 4. 측정 측정측정 측정 기준 기준기준 기준 41. 시험 시험시험 시험 장비 장비장비 장비 Network Analyzer HP8753ES Calibration Kit HP85033D High Resistance Meter HP4277A Withstanding Voltage Tester TOS8750 Adaptor SMA Type Female ↔ SMA male Measurement Cable 81204779 (Hewlett Packard) 42. 시험 시험시험 시험 장비 장비장비 장비 Setting Display Dual Channel : : : : On Split Display : :: : On Menu Number of Points : 201 Power : :: : 0 dBm Measure Channel 1 : :: : S11 Channel 2 : :: : S21 43. Calibration Calibration- -- - Cal. Kit : 50 Ω ΩΩ Ω Calibration menu → →→ → Full2 Port Reflection Forward : :: : Open → →→ → Short → →→ → Load Reverse : :: : Open → →→ → Short → →→ → Load Done Transmission Do Both → →→ → FWD + ++ + REV Done Isolation Omit Isolation Done WINiZEN Co. Ltd. 8 Document No. WAT–1206–EX148I Rev. No. IR Model Name W5IBO07 (150 mm) 5. 시험 시험시험 시험 절차 절차절차 절차 51. VSWR Step 1. Antenna를 를를 를 Adaptor 가 가가 가 포함된 포함된포함된 포함된 Cable로 로로 로 Network Analyzer의 의의 의 Port1에 에에 에 연결한다 연결한다연결한다 연결한다. Step 2. 해당 해당해당 해당 주파수 주파수주파수 주파수 대역의 대역의대역의 대역의 Marker Point를 를를 를 Network Analyzer위에 위에위에 위에 표시한다 표시한다표시한다 표시한다. Step 3. VSWR 값 값값 값을 을을 을 확인한다 확인한다확인한다 확인한다. Step 4. Data를 를를 를 측정한다 측정한다측정한다 측정한다. WINiZEN Co. Ltd. 9 52. 이 이이 이득 득득 득 및 및및 및 방사패턴 방사패턴방사패턴 방사패턴 측정 측정측정 측정 Step 1 Chamber와 와와 와 주파수대역의 주파수대역의주파수대역의 주파수대역의 시스템을 시스템을시스템을 시스템을 Calibration과 과과 과 동시에 동시에동시에 동시에 Chamber의 의의 의 제어를 제어를제어를 제어를 위한 위한위한 위한 소프트웨어를 소프트웨어를소프트웨어를 소프트웨어를 확인한다 확인한다확인한다 확인한다 Step 2. 측정할 측정할측정할 측정할 Antenna를 를를 를 Chamber 내부의 내부의내부의 내부의 측정할 측정할측정할 측정할 위치에 위치에위치에 위치에 놓는다 놓는다놓는다 놓는다. Step 3. Chamber의 의의 의 제어 제어제어 제어 Program을 을을 을 작동하여 작동하여작동하여 작동하여 측정을 측정을측정을 측정을 시작한다 시작한다시작한다 시작한다 Step 4. Data를 를를 를 측정한다 측정한다측정한다 측정한다. WINiZEN Co. Ltd. 11 61 VSWR 62 S11 WINiZEN Co. Ltd. 12 63 Radiation Pattern a. Azimuth Pattern b. Elevation Pattern WINiZEN Co. Ltd. 13 Document No. WAT–1206–EX148I Rev. No. IR Model Name W5IBO07 (150 mm) 7. Reliability Test Item Specification Conditions Test Result Salt-water Resistance No change of material characteristic Temperature of 35°C, Concentration of 5%, Let stand for 48 hours OK Humidity Resistance Changeable range of V.S.WR value±0.5 No change of material characteristic Temperature of 40°C, Humidity of 95%, Let stand for 96 hours OK Temperature Test 85 40 25 0 -40 85°C, 30% 40°C, 80% -40°C, 0% 25°C, 65% (H) 1 Cycle (°C) Changeable range of V.S.WR value±0.5 No change of material characteristic Increasing from +25°C, 65% to +85°C, 30%; 35min / Keeping on +85°C, 30% for 6hour / Decreasing from +85°C, 30% to +40°C, 80%; 20min / Keeping on +40°C, 80% for 8hour / Decreasing from +40°C, 80% to -40°C, 0%; 60min / Keeping on -40°C, 0% for 4hour / Increasing from -40°C, 0% to 25°C, 65%; 45min / Keeping on 25°C for 3hour / 5Cycle time = 118hour and 20min OK Drop Antenna 1.5m Steel Plate (2t) No disconnection No crack or damage Drop the antenna at 1.5m height to the steel plate (2t) of ground OK WINiZEN Co. Ltd. 14 Document No. WAT–1206–EX148I Rev. No. IR Model Name W5IBO07 (150 mm) 8. Packaging WINiZEN Co. Ltd. 15 Part Name: 2.4 GHz Internal Antenna 2012.6.15 Substance Substance NameCdPbHgCr+6 PBBs PBDEs CableInsulatorPTFENDNDNDNDNDND2011.1.18 ConductorCopperNDNDNDNDNDND2011.1.18 JacketFEPNDNDNDNDNDND2011.1.18 ShieldSilverplated copperNDNDNDNDNDND2011.1.18 IPEX ConnectorHousing (black)PBTNDNDNDNDNDND2010.2.22 ContactPhosphor Bronze StripND20NDNDNDND2010.2.22 Ground contactCopperND19NDNDNDND2010.2.22 PCBFR-4EPOXYND5NDNDNDND2011.8.22 SolderLead alloyND290NDNDNDND2011.3.10 TOTAL Break down of the component Name of part 자료첨부 (MSDS/MD) Part No. W5I-BO-07 Chemical constituentsMATERIAL ANALYSIS ANALYSIS RESULT (ppm) Analysis date 자료첨부 (RoHS 성적서 ) Adobe Acrobat 7.0 Document Adobe Acroba…

Text truncated - open the document above for the full version.

CTK Co., Ltd. 386-1, Ho-dong, Cheoin-gu, Yongin-si, Gyeonggi-do, 449-100, Korea Tel: +82-31-339-9970 Fax: +82-31-339-9855 www.e-ctk.com Page 1 of 2 RF EXPOSURE EVALUATION Applicant : Shin Heung Precision Co., Ltd. Applicant Address : 222-2, Sinneung-Ri, Seowun-Myeon, Anseong- City, Gyeonggi-Do, 456-853, Korea Kind of Product : POS PRINTER Equipment model name : ELLIX4abc RF power : 13.229 dBm Peak Conducted Antenna type : Internal antenna Antenna Gain : 3.384 dBi Frequency Range : 2402 - 2480 MHz Number of channels : 79 CH CTK Co., Ltd. 386-1, Ho-dong, Cheoin-gu, Yongin-si, Gyeonggi-do, 449-100, Korea Tel: +82-31-339-9970 Fax: +82-31-339-9855 www.e-ctk.com Page 2 of 2 ** MPE Calculations ** The EUT will only be used with a separation of 20 centimeters or greater between the antenna and the body of the user. The MPE calculation for this exposure is shown below. The peak radiated output power (EIRP) is calculated as follows: EIRP = P + G Where, P = Power input to the antenna (mW) G = Power gain of the antenna (dBi) EIRP = 13.229 + 3.384 = 16.613 dBm => 45.846 mW The numeric gain(G) of the antenna with a gain specified in dB is determined by: G = Log -1 (dB antenna gain / 10) G = Log -1 (3.384/ 10) G = 2.18 Power density at the specific separation: S = PG/(4R 2 π) Where, S = Maximum power density (mW/cm 2 ) P = Power input to the antenna (mW) G = Numeric power gain of the antenna R = Distance to the center of the radiation of the antenna (20cm = limit for MPE) S = (45.846)/(4 * 20 2 * π) S =0.009 mW/cm 2 The Maximum permissible exposure (MPE) for the general population is 1 mW/cm 2 . The power density at 20cm does not exceed the 1 mW/cm 2 limit. Estimated safe separation: R = √(PG / 4π) Where, P = Power input to the antenna (mW) G = Numeric power gain of the antenna R = Distance to the center of the radiation of the antenna (20cm = limit for MPE) R = √(45.846 / 4π) R = 1.91 cm

CTK Co., Ltd. 386-1, Ho-dong, Cheoin-gu, Yongin-si, Gyeonggi-do, 449-100, Korea Tel: +82-31-339-9970 Fax: +82-31-339-9855 www.e-ctk.com Test Report No.: CTK-2013-01208 Date: July 26, 2013 Page 1 of 38 This Report shall not be reproduced except in full without the written approval of CTK Form No.: CTK-RF-EF-Part15 SubpartC(Rev.2) TEST REPORT For FCC FCC Standards : FCC 47CFR part 15 subpart C Test Report No. : CTK-2013-01208 Date of Issue : July 26, 2013 FCC ID : O8H-ELLIX40B Basic Model/Type No. : ELLIX4abc Variant Model/Type No. : SR85, TP-40, SI-300L, TAB-10 Kind of Product : POS PRINTER Applicant : Shin Heung Precision Co., Ltd. Applicant Address : 222-2, Sinneung-Ri, Seowun-Myeon, Anseong-City, Gyeonggi- Do, 456-853, Korea Manufacturer : Shin Heung Precision Co., Ltd. Manufacturer Address : 222-2, Sinneung-Ri, Seowun-Myeon, Anseong-City, Gyeonggi- Do, 456-853, Contact Person : Byoungjo-Ha / Chief Engineer Telephone : +82–2-2101-9672 Received Date : April 25, 2013 Test period : Start : June 25, 2013 End : July 25, 2013 The test results presented in this report relate only to the object tested. Tested by Reviewed by Young-taek Lee Test Engineer Young-Joon, Park Technical Manager Date: July 26, 2013 Date: July 26, 2013 CTK Co., Ltd. 386-1, Ho-dong, Cheoin-gu, Yongin-si, Gyeonggi-do, 449-100, Korea Tel: +82-31-339-9970 Fax: +82-31-339-9855 www.e-ctk.com Test Report No.: CTK-2013-01208 Date: July 26, 2013 Page 2 of 38 This Report shall not be reproduced except in full without the written approval of CTK Form No.: CTK-RF-EF-Part15 SubpartC(Rev.2) REPORT REVISION HISTORY Date Revision Page No July 26, 2013 Issued (CTK-2013-01208) All This report shall not be reproduced except in full, without the written approval of CTK Co., Ltd. This document may be altered or revised by CTK Co., Ltd. personnel only, and shall be noted in the revision section of the document. Any alteration of this document not carried out by CTK Co., Ltd. will constitute fraud and shall nullify the document. CTK Co., Ltd. 386-1, Ho-dong, Cheoin-gu, Yongin-si, Gyeonggi-do, 449-100, Korea Tel: +82-31-339-9970 Fax: +82-31-339-9855 www.e-ctk.com Test Report No.: CTK-2013-01208 Date: July 26, 2013 Page 3 of 38 This Report shall not be reproduced except in full without the written approval of CTK Form No.: CTK-RF-EF-Part15 SubpartC(Rev.2) TABLE OF CONTENTS REPORT REVISION HISTORY ........................................................................................... 2 1.0 General Product Description ................................................................................ 4 1.1 Tested Frequency ............................................................................................... 4 1.2 Tested Mode ...................................................................................................... 4 1.3 Model Differences .............................................................................................. 5 1.4 Device Modifications ........................................................................................... 5 1.5 Peripheral Devices ............................................................................................. 5 1.6 Calibration Details of Equipment Used for Measurement ......................................... 5 1.7 Test Facility ....................................................................................................... 5 1.8 Laboratory Accreditations and Listings .................................................................. 6 2.0 Summary of tests .............................................................................................. 7 2.1 Transmitter Requirements ................................................................................... 8 2.1.1 Carrier Frequency Separation ........................................................................ 8 2.1.2 Number of Hopping Frequencies .................................................................. 10 2.1.4 Time of Occupancy (Dwell Time) .................................................................. 15 2.1.5 Maximum peak Conducted Output Power ...................................................... 19 2.1.6 Band-edge ................................................................................................ 22 2.1.7 Field Strength of Emissions ......................................................................... 28 2.1.8 AC Conducted Emissions ............................................................................. 35 APPENDIX A – Test Equipment Used For Tests ................................................................. 38 CTK Co., Ltd. 386-1, Ho-dong, Cheoin-gu, Yongin-si, Gyeonggi-do, 449-100, Korea Tel: +82-31-339-9970 Fax: +82-31-339-9855 www.e-ctk.com Test Report No.: CTK-2013-01208 Date: July 26, 2013 Page 4 of 38 This Report shall not be reproduced except in full without the written approval of CTK Form No.: CTK-RF-EF-Part15 SubpartC(Rev.2) 1.0 General Product Description Equipment model name ELLIX4abc Serial number Prototype EUT condition Pre-production, not damaged Antenna type Internal antenna Gain 3.384 dBi Frequency Range 2402 MHz - 2480 MHz RF power 13.229 dBm Peak Conducted Type of Modulation Frequency Hopping Spread Spectrum Number of channels 79 Channel Spacing 1 MHz Channel Access Protocol Frequency Hopping Type of Modulation GFSK Power Source AC/DC ADAPTER INPUT : 100-240 Vac, 2.0 A OUTPUT : 24 Vdc, 2.5 A 1.1 Tested Frequency LOW MID HIGH Frequency (MHz) 2402 2441 2480 1.2 Tested Mode - Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). - Following channel(s) was (were) selected for the final test as listed below. Tested Ch Modulation Technology Modulation Type Packet Type Low, Mid, High FHSS GFSK DH 5 CTK Co., Ltd. 386-1, Ho-dong, Cheoin-gu, Yongin-si, Gyeonggi-do, 449-100, Korea Tel: +82-31-339-9970 Fa…

Text truncated - open the document above for the full version.

CTK Co., Ltd. 386-1, Ho-dong, Cheoin-gu, Yongin-si, Gyeonggi-do, 449-100, Korea Tel: +82-31-339-9970 Fax: +82-31-339-9855 www.e-ctk.com Test Setup Photographs and Configuration Conducted Voltage Emissions CTK Co., Ltd. 386-1, Ho-dong, Cheoin-gu, Yongin-si, Gyeonggi-do, 449-100, Korea Tel: +82-31-339-9970 Fax: +82-31-339-9855 www.e-ctk.com Radiated Electric Field Emissions CTK Co., Ltd. 386-1, Ho-dong, Cheoin-gu, Yongin-si, Gyeonggi-do, 449-100, Korea Tel: +82-31-339-9970 Fax: +82-31-339-9855 www.e-ctk.com CTK Co., Ltd. 386-1, Ho-dong, Cheoin-gu, Yongin-si, Gyeonggi-do, 449-100, Korea Tel: +82-31-339-9970 Fax: +82-31-339-9855 www.e-ctk.com