OQW-STR1800UHF Non-Broadcast Radio

SRI Summation Research Inc STR-1800 Land Mobile Data Radio Operations and Maintenance Manual Meeting 21 st Century Challenges - with – Technically Appropriate Solutions Prepared by: Summation Research Inc – Melbourne, FL SRI Document Number: 70-STR1800-00 O&M Revision: K This document contains information proprietary and confidential to SRI. Transmittal, receipt, or possession of this document does not express, license, or imply any rights to use, design, or manufacture from this information. No reproduction, publication, or disclosure of this information, in whole or in part, shall be made without prior written authorization from an officer of SRI. SRI • 305 EAST DR STE D • MELBOURNE, FLORIDA 32904 +1 (321) 254-2580 • FAX +1 (321) 254-2492 •http://www.summationresearch.com [email protected] © Copyright 2010, 2011, 2012. 2018, 2020 SRI Printed in U.S.A. (Intentionally Left Blank) 70-STR1800-00 Rev K STR-1800 O&M Manual - i - SUMMATION RESEARCH, INC. LIMITED WARRANTY Summation Research, Inc. (herein called SRI) warrants that the equipment’s of its manufacture as identified and described within this manual shall, at the time of shipment to the original purchaser, be free from defects in material and workmanship. This warranty applies only to equipment installed, operated, and maintained in accordance with SRI recommendations. This warranty does not apply where SRI determines that installation, repair, alteration, or accidents have caused any claimed defect, or that excessive deterioration due to environmental contamination has occurred. SRI’s obligation under this warranty is limited to repairing, or replacing, exclusive of cost of installation and labor charges, any part that SRI determines to be defective, provided that such part is received at SRI’s principal office, freight prepaid. All equipment's must receive prior approval for return to SRI for warranty repair and must be sent prepaid. If they are returned collect, they will not be accepted. This warranty is subject to any existing conditions of supply that may directly affect SRI’s ability to obtain materials or manufacture replacement parts. SRI makes no warranty that the equipment shall be merchantable or fit for any particular purpose; nor does SRI make other warranties, express or implied, by operation of law or otherwise, except such as are expressly set forth herein. SRI shall not be liable to buyer, or to any third persons for any incidental, consequential, special or contingent damages for breach of any warranty. All specifications within this document are subject to change without prior written notice. 70-STR1800-00 Rev K STR-1800 O&M Manual - ii - (Intentionally Left Blank) 70-STR1800-00 Rev K STR-1800 O&M Manual - iii - RF Exposure Statement The radio generates RF electromagnetic energy during transmit mode. This radio is designed for and classified as “Occupational Use Only”, meaning it must be used only during the course of employment by individuals aware of the hazards, and the ways to minimize such hazards. This radio is NOT intended for use by the “General Population” in an uncontrolled environment. The antennas used for this transmitter must be installed to provide a separation distances from the human body as noted below. Users and installers must be provided with antenna installation and transmitter operating conditions for satisfying RF exposure compliance. For compliance with FCC, Industry Canada, and ETSI RF Exposure Requirements, the transmitter antenna installation shall comply with the following two conditions: 1. The transmitter antenna gain shall not exceed a limit necessary for the application. 2. The transmitter antenna is required to be located outside of a vehicle and kept at a separation distance of 60 centimeters (FCC, UHF), 80 centimeters (ISED, UHF), 50 centimeters (ETSI, UHF) or 65 centimeters (ETSI, VHF) or more between the transmitter antenna of this device and persons during operation. To ensure that your exposure to RF electromagnetic energy is within the FCC allowable limits for occupational use, always adhere to the following guidelines: • DO NOT operate the radio without a proper antenna attached, as this may damage the radio and may also cause you to exceed FCC RF exposure limits. A proper antenna is the antenna supplied with this radio by the manufacturer or an antenna specifically required to meet application requirements. • DO NOT transmit for more than 25% of total radio use time (“25% duty cycle”). Transmitting more than 25% of the time can cause RF exposure compliance requirements to be exceeded. This device has been designated to operate with the antennas listed below and having a maximum gain of 2.15 dBi. Antennas not included in this list or having a gain greater than 2.15 dBi are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. Recommended Antennas: Type: Omni-directional, Gain: 2.15 dBi The STR-1800 series of radios include a transmit time-out timer to prevent continuous transmissions greater than fifteen (15) seconds. This timer starts when the PTT or equivalent signal is asserted and when this timer expires, the radio will stop transmitting immediately and may not re-transmit until PTT has been asserted again. Electromagnetic Interference/Compatibility During transmissions, the radio generates RF energy that can possibly cause interference with other devices or systems. To avoid such interference, turn off the radio in areas where signs are posted to do so. DO NOT operate the transmitter in areas that are sensitive to electromagnetic radiation such as hospitals, aircraft, and blasting sites. Declaration of Conformity and Compliance This device complies with FCC Part 15 and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of th…

Text truncated - open the document above for the full version.

Summation Research, Inc. STR-1800 Model Differences PROPRIETARY AND CONFIDENTIAL The STR-1800 family includes the following models, with differences noted. Model STR-1820A Simplex UHF Data Transceiver with single transmit and single receive capability Front Panel Card (FPC) Main Radio Chassis Front Panel Bezel DB - 25 DB - 9 Flex Modem Data Card (MDC) Conn Molex Pwr Conn UHF Conn PTT Chan Sel (4) Tx/Rx Audio Diag/Prog I/O RF Antenna 13.6 VDC Main Radio Card Conn TX RX TXRX Switch System Overview, Single Receive Channel Model STR-1820A Model STR-1821A Simplex UHF Data Transceiver with single transmit and dual receive capability Front Panel Card (FPC) Main Radio Chassis Front Panel Bezel DB - 25 DB - 9 Flex Enhanced Modem Card (EMC) Conn Molex Pwr Conn UHF Conn PTT Chan Sel (4) Tx/Rx Audio Diag/Prog I/O RF Antenna 13.6 VDC Main Radio Card ÷ Conn TX RX1 RX2 TXRX Switch System Overview, Dual Receive Channel Model STR-1821A

Section 9 EUT photos Report reference ID: 393579-1TRFWL Page 37 of 40 EUT photos 9.1 External photos Figure 9.1-1: Front view photo Section 9 EUT photos Report reference ID: 393579-1TRFWL Page 38 of 40 Figure 9.1-2: Rear view photo Section 9 EUT photos Report reference ID: 393579-1TRFWL Page 39 of 40 Figure 9.1-3: Side views photos Section 9 EUT photos Report reference ID: 393579-1TRFWL Page 40 of 40 Figure 9.1-4: Bottom view photo End of the test report

305 East Dr Ste D, Melbourne, FL 32904 (321) 254-2580; Fax: (321) 254-2492 [email protected] www.summationresearch.com Summation Research, Inc. STR-1800 Label Format and Location Label Format Model STR-1820A Label Model STR-1821A Label Label Location

Summation Research, Inc. STR-1800 Internal Photographs PROPRIETARY AND CONFIDENTIAL Main Board, top Main Board, Top, Shields Removed Summation Research, Inc. STR-1800 Internal Photographs PROPRIETARY AND CONFIDENTIAL Main Board, Shields Removed, Detail Summation Research, Inc. STR-1800 Internal Photographs PROPRIETARY AND CONFIDENTIAL Modem Card, Top Modem Card, Bottom Summation Research, Inc. STR-1800 Internal Photographs PROPRIETARY AND CONFIDENTIAL Front Panel Card, Front Front Panel Card, Rear

305 East Dr Ste D, Melbourne, FL 32904 (321) 254-2580; Fax: (321) 254-2492 [email protected] www.summationresearch.com STR-1800 Tune-Up Information This is to confirm that all frequencies, power levels, deviation, bandwidth, and other RF operational options are programmed by a trained and authorized technician. Users are unable to program or operate the radio with other than these previously programmed.

Applicant:Summation Research HVIN:STR‐1820A, STR‐1821A PMN:UHF Non‐Broadcast Radio Certification Number:9110A‐STR1800 FCC ID:OQW‐STR1800 FCC 1.1310 General Population/Uncontrolled Exposure FrequencyPower Antenna GainDuty Cycle EIRP 1 EIRPDistance DPD 2 Limit 3 Margin MHzdBmdBi%dBmmWcmmW/m^2mW/cm^2dB 452.92544.992.152541.112940600.2860410.3019500.235074 PD=EIRP/(4xπxD 2 ) CANADA RSS‐102, Issue 5 General Population/Uncontrolled Exposure FrequencyPower Antenna GainDuty Cycle EIRP 1 EIRPDistance DPD 2 Limit 3 Magin MHzdBmdBi%dBmWmW/m^2W/m^2dB 452.92544.992.152541.112.94020.81.608981.711050.26714 PD=EIRP/(4xπxD 2 ) 1 EIRP = Power dBm + Antenna Gain dBi + 10xLog(Duty Cycle/100) 2 Power Density PD = EIRP / (4xπxD 2 ) [Health Canada Technical Guide ‐ Safety Code 6_2015, Eq 5‐6 at 5.2; OET Bulletin 65, Edition 97‐01, August 1997, Eq (4)] 3 RSS‐102 Issue 5 Table 4; FCC 1.1310 Table 1

www.nemko.com Nemko Canada Inc., a testing laboratory, is accredited by the Standards Council of Canada. The tests included in this report are within the scope of this accreditation FCC 90-I, RSS-119 Issue 12; Date: March, 2020 SCC Accredited LAB LAB Accrédité CCN TM Choose Scandinavian trust RADIO TEST REPORT – 393579-1TRFWL Type of assessment: Final product testing Applicant: Product name (type): Summation Research Inc. STR-1800 Land Mobile Data Radio Series: Model: Model variant: STR-1800 STR-1820A STR-1821A FCC ID: IC Registration number: OQW-STR1800 9110A-STR1800 Specifications:  FCC 47 CFR Part 90, Subpart I  RSS-119, Issue 12, May 2015 Date of issue: June 5, 2020 Andrey Adelberg, Senior EMC/RF Specialist Tested by Signature Kevin Rose, EMC/RF Lab Manager Reviewed by Signature Report reference ID: 393579-1TRFWL Page 2 of 38 Lab locations Company name Nemko Canada Inc. Facilities Ottawa site: 303 River Road Ottawa, Ontario Canada K1V 1H2 Tel: +1 613 737 9680 Fax: +1 613 737 9691 Montréal site: 292 Labrosse Avenue Pointe-Claire, Québec Canada H9R 5L8 Tel: +1 514 694 2684 Fax: +1 514 694 3528 Cambridge site: 1-130 Saltsman Drive Cambridge, Ontario Canada N3E 0B2 Tel: +1 519 650 4811 Almonte site: 1500 Peter Robinson Road West Carleton, Ontario Canada K0A 1L0 Tel: +1 613 256-9117 Fax: +1 613 256-8848 Test site registration Organization Recognition numbers and location FCC/ISED FCC: CA2040; IC: 2040A-4 (Ottawa/Almonte); FCC: CA2041; IC: 2040G-5 (Montreal); CA0101 (Cambridge) Website www.nemko.com Limits of responsibility Note that the results contained in this report relate only to the items tested and were obtained in the period between the date of initial receipt of samples and the date of issue of the report. This test report has been completed in accordance with the requirements of ISO/IEC 17025. All results contained in this report are within Nemko Canada’s ISO/IEC 17025 accreditation. Copyright notification Nemko Canada Inc. authorizes the applicant to reproduce this report provided it is reproduced in its entirety and for use by the company’s employees only. Any use which a third party makes of this report, or any reliance on or decisions to be made based on it, are the responsibility of such third parties. Nemko Canada Inc. accepts no responsibility for damages, if any, suffered by any third party as a result of decisions made or actions based on this report. © Nemko Canada Inc. Report reference ID: 393579-1TRFWL Page 3 of 38 Table of Contents Table of Contents ......................................................................................................................................................................................................... 3 Report summary ................................................................................................................................................................................. 4 1.1 Test specifications .................................................................................................................................................................................................... 4 1.2 Test methods ............................................................................................................................................................................................................ 4 1.3 Exclusions ................................................................................................................................................................................................................. 4 1.4 Statement of compliance .......................................................................................................................................................................................... 4 1.5 Test report revision history ....................................................................................................................................................................................... 4 Engineering considerations ................................................................................................................................................................. 5 2.1 Modifications incorporated in the EUT for compliance ............................................................................................................................................ 5 2.2 Technical judgment .................................................................................................................................................................................................. 5 2.3 Deviations from laboratory tests procedures ........................................................................................................................................................... 5 Test conditions ................................................................................................................................................................................... 6 3.1 Atmospheric conditions ............................................................................................................................................................................................ 6 3.2 Power supply range .................................................................................................................................................................................................. 6 Measurement uncertainty .................................................................................................................................................................. 7 4.1 Uncertainty of measurement ................................................................................................................................................................................... 7 Information provided by the applicant .................................................................................…

Text truncated - open the document above for the full version.