OUC-11543680Gen 3 WCM

FCC Information that must be included in the User’s Manual. Omron is responsible for the design, manufacturing and FCC Type approval certification. The “Wireless Control Module” (WCM): WCM Model #: 11543680 is tested and met the FCC requirements. It is FCC requirement that the following information be included in the user’s manual. “This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.” June 25, 2012 Matthew Colburn _________________ Omron Automotive Electronics EMC Engineer Tel# (630)443-6800 Ext 347 E-Mail: [email protected] CC: D.E.New Chrysler Product Engineer

Engineering Test Report No. 1201896-01 Measurement of RF Emissions from a Wireless Control Module with Embedded Transmitter , Model No. WCM For Omron Electronics 3709 Ohio Avenue St. Charles, IL 60174 P.O. Number 71534N Date Tested February 6 through 21, 2012 Test Personnel Daniel Crowder Test Specification FCC "Code of Federal Regulations” Title 47, Part15 Industry Canada RSS-GEN Test Report By: Daniel Crowder EMC Engineer Requested By: Matthew Colburn Omron Electronics Approved By: Raymond J. Klouda Registered Professional Engineer of Illinois - 44894 Elite Electronic Engineering, Inc. 1516 Centre Circle Downers Grove, IL 60515 Tel : (630) 495-9770 Fax: (630) 495-9785 www.elitetest.com Engineering Test Report No. 1201896-01 TABLE OF CONTENTS PARAGRAPH DESCRIPTION OF CONTENTS PAGE NO. THIS REPORT SHALL NOT BE REPRODUCED, EXCEPT IN FULL, WITHOUT THE WRITTEN APPROVAL OF ELITE ELECTRONIC ENGINEERING INCORPORATED. Page 2 of 17 1. Introduction ................................................................................................................................................... 4 1.1. Scope of Tests ..................................................................................................................................... 4 1.2. Purpose ............................................................................................................................................... 4 1.3. Deviations, Additions and Exclusions .................................................................................................. 4 1.4. EMC Laboratory Identification ............................................................................................................. 4 1.5. Laboratory Conditions.......................................................................................................................... 4 2. Applicable Documents .................................................................................................................................. 4 3. EUT Setup and Operation ............................................................................................................................ 4 3.1. General Description ............................................................................................................................. 4 3.1.1. Power Input ................................................................................................................................. 5 3.1.2. Peripheral Equipment ................................................................................................................. 5 3.1.3. Signal Input/Output Leads .......................................................................................................... 5 3.1.4. Grounding ................................................................................................................................... 5 3.2. Operational Mode ................................................................................................................................ 5 3.3. EUT Modifications ................................................................................................................................ 5 4. Test Facility and Test Instrumentation ......................................................................................................... 5 4.1. Shielded Enclosure .............................................................................................................................. 5 4.2. Test Instrumentation ............................................................................................................................ 5 4.3. Calibration Traceability ........................................................................................................................ 5 4.4. Measurement Uncertainty ................................................................................................................... 5 5. Test Procedures ........................................................................................................................................... 6 5.1. Radiated Measurements ..................................................................................................................... 6 5.1.1. Requirements .............................................................................................................................. 6 5.1.2. Procedures .................................................................................................................................. 6 5.1.3. Results ........................................................................................................................................ 6 6. Other Test Conditions .................................................................................................................................. 6 6.1. Test Personnel and Witnesses ............................................................................................................ 6 6.2. Disposition of the EUT ......................................................................................................................... 6 7. Conclusions .................................................................................................................................................. 7 8. Certification................................................................................................................................................... 7 9. Equipment List .............................................................................................................................................. 8 Engineering Test Report No. 1201896-01 Page 3 of 17 REVISION HISTORY Revision Date Description — 7 June 2012 Initial release Engineering Test Report No. 1201896-01 Page 4 of 17 Measurement of RF Emissions from a Wireless Control Module with Embedded Transmitter, Model No. WCM 1. INTRODUCTION 1.1. Scope of Tests Th…

Text truncated - open the document above for the full version.

Engineering Test Report No. 1201896-01 Page 11 of 17 Figure 3 Test Setup for Radiated Emissions, Below 30MHz – Horizontal Polarization Test Setup for Radiated Emissions, Below 30MHz – Vertical Polarization