OUC60221Remote Control Transmitter

PNSPO  3 Common Architecture Tx- User Manual/FCC ID FCC ID: OUC60221 IC: 850K60221 This keyless entry system operates on a radio frequency subject to Federal Communication Commission (FCC) rules and Industry Canada rules. This device complies with Part 15 of FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions 1.) This device may not cause harmful interference. 2.) This device must accept any interference received, including interference that may cause undesired operation of the device. The term “IC:” before the radio certification number only signifies that Industry Canada technical specifications were met. FCC Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: The statements expressed above should be placed in the owner’s user manual.

PNSPO  10 Figure 7. Top-side Final Assembly PNSPO  11 Figure 8. Bottom-side Final Assembly

PNSPO  11 Figure 8. Bottom-side Final Assembly

PNSPO  6 Figure 3.Top side of PCB PNSPO  7 Figure 4. Bottom side of PCB

Engineering Test Report No. 1000652-01 Measurement of RF Interference from a Model D0000221 RKE FOB Transmitter For : Omron Electronics 3709 Ohio Avenue St. Charles, IL 60174 Date Tested : February 17, 24 and 25, 2010 Test Personnel : Richard King Specification : FCC "Code of Federal Regulations" Title 47 Part 15, Subpart C : Industry Canada RSS-210 : Industry Canada RSS-GEN Test Report By : Richard King Approved By : Raymond J. Klouda Registered Professional Engineer of Illinois - 44894 Elite Electronic Engineering Inc. 1516 Centre Circle Downers Grove, IL 60515 Tel : (630) 495-9770 Fax: (630) 495-9785 www.elitetest.com Engineering Test Report No. 1000652-01 TABLE OF CONTENTS PARAGRAPH DESCRIPTION OF CONTENTS PAGE NO. Page 2 of 21 1 INTRODUCTION..........................................................................................................................................4 1.1 Scope of Tests..................................................................................................................................... 4 1.2 Purpose ............................................................................................................................................... 4 1.3 Deviations, Additions and Exclusions.................................................................................................. 4 1.4 EMC Laboratory Identification ............................................................................................................. 4 1.5 Laboratory Conditions ......................................................................................................................... 4 2 APPLICABLE DOCUMENTS .......................................................................................................................4 3 TEST ITEM SETUP AND OPERATION.......................................................................................................4 3.1 General Description ............................................................................................................................. 4 3.1.1 Power Input ..................................................................................................................................... 5 3.1.2 Peripheral Equipment...................................................................................................................... 5 3.1.3 Interconnect Cables ........................................................................................................................ 5 3.1.4 Grounding........................................................................................................................................ 5 3.2 Operational Mode ................................................................................................................................ 5 3.3 Test Item Modifications........................................................................................................................ 5 4 TEST FACILITY AND TEST INSTRUMENTATION.....................................................................................5 4.1 Shielded Enclosure.............................................................................................................................. 5 4.2 Test Instrumentation ............................................................................................................................ 5 4.3 Calibration Traceability ........................................................................................................................ 5 4.4 Measurement Uncertainty ................................................................................................................... 5 5 TEST PROCEDURES..................................................................................................................................6 5.1 Powerline Conducted Emissions ......................................................................................................... 6 5.1.1 Requirements .................................................................................................................................. 6 5.2 Duty Cycle Factor Measurements ....................................................................................................... 6 5.2.1 Procedures ...................................................................................................................................... 6 5.2.2 Results ............................................................................................................................................ 6 5.3 Radiated Measurements ..................................................................................................................... 6 5.3.1 Requirements .................................................................................................................................. 6 5.3.2 Procedures ...................................................................................................................................... 7 5.3.3 Results ............................................................................................................................................ 7 5.4 Occupied Bandwidth Measurements................................................................................................... 7 5.4.1 Requirement.................................................................................................................................... 7 5.4.2 Procedures ...................................................................................................................................... 8 5.4.3 Results ............................................................................................................................................ 8 6 OTHER TEST CONDITIONS .......................................................................................................................8 6.1 Test Personnel and Witnesses........…

Text truncated - open the document above for the full version.

Engineering Test Report No. 1000652-01 Page 11 of 21 Figure 2 Test Setup for Radiated Emissions – Horizontal Polarity Test Setup for Radiated Emissions – Vertical Polarity Engineering Test Report No. 1000652-01 Page 12 of 21 Figure 3 Test Setup for Radiated Emissions – Horizontal Polarity Test Setup for Radiated Emissions – Vertical Polarity