OVJP118Pedometer watch

User’s Manual Bluetooth 4.0 Pedometer P118 To ensure the accuracy of data, please read this manual carefully before using it. Accessories Figure silicone wristband belt clip Pedometer (without battery) 1.System Block Screen Tap=Mode key Bettery hatch 2. Battery Assembly Light Disk USB DONGLE During transport, regular turbulence, vibration, can make B.T Pedometer misjudgment, produce abnormal data. In order to avoid to product abnormal data, In the process of packaging, battery and Pedometer separated packing. Before use, the battery must be installed to the Pedometer. - After twisting battery door well, screen shows the default time 00:00, knock on a screen, interface will cyclic display among time - step - calories – distance. - Now you can set the Pedometer connection. 3. Setting the connection on mobile devices The Pedometer only can build connection and synchronization of data with mobile devices which support Bluetooth 4.0, currently supports Android 4.3 and following specific models. Ready to set up the connection - Copy from the accompanying CD or from the App Store (IOS) and Google App Store (Android) download and install the isportActivity Monitor (below short called APP). - If you have installed the APP, please ensure that your APP to the latest version. - To ensure the Bluetooth is open on a mobile device. Connect with IOS device Your B.T Pedometer need match connection with your IOS device only by APP, it can't search by your IOS device to connect: - Open the APP, make sure the distance between your B.T Pedometer and the IOS device is not more than 5 m, B.T Pedometer in the awake state. - Enter the APP equipment list, click refresh device, the APP will search nearby B.T Pedometer, and put searched B.T Pedometer included in the equipment list. - In the equipment list, click devices which your need match, the APP will match with devices you clicked, and automatically synchronize data - Enter the personal Settings interface, setting up your information, click the "save" to storage your information to the APP and synchronization to your B.T Pedometer. Cr2025 Battery Synchronous data to iOS devices Connection with Android devices The Pedometer need match connection with your Android device only by APP, it can't search by your Android device to connect. - Enter the APP equipment list, click refresh device, the APP will search near by the Pedometer, and put searched P118 included in the equipment list - In the equipment list, click devices which your need match, the APP will match with devices you clicked, and automatically synchronize data - Enter the personal Settings interface, setting up your information, click the "save" to storage your information to the APP and synchronization to the Pedometer. Synchronous data to Android devices Automatic synchronization: the Pedometer can synchronize data directly to the Android device. Every time open the APP, the APP will connect to the Pedometer immediately and synchronous data;every 30 minutes automatically synchronize data. - Automatic synchronization: your B.T Pedometer can synchronize data directly to the IOS device. Every time open the APP, the APP will connect to B.T Pedometer immediately and synchronous data;every 30 minutes automatically synchronize data. Remark: iOS bluetooth devices must be in state of opening.If you do not open, the APP will reminder to open bluetooth device.IOS device did not open the bluetooth device, operating APP may cause APP automatically exit. - When IOS device display is opened, then can automatically synchronize data;If your IOS device display screen is closed, you will not be able to synchronous data automatically. - Manual sync: if you want to get the latest data, you also can manually synchronize the data.Open the APP, clickright sidegear icon signon the APP toenter setup interface, click the upper left corner of the icon that can be manually sync data. Brand Phone type iPhone 4S iPhone 5 iPhone 5C iPhone 5S iPhone Operating system IOS 6.0.0 IOS 6.0.0 IOS 6.0.0 IOS 6.0.0 iPod iPad IOS 6.0.0 IOS 6.0.0 Galaxy S3 Galaxy S4 Samsung Android 4.3 Android 4.3 Android 4.3 CR2025 + 123 1. from packaging to take out the Pedometer, then use COINS to unlock the battery cover. Insert a coin into the back of the battery cover slot, and counterclockwise to turn the battery cover off. 2. After open the battery cover, put battery into the Pedometer, the battery "+" up, put the battery into the battery compartment. 3. After put the battery, battery cover with the arrow point on the Pedometer "unlocked" sign, the battery cover should be in place, use COINS clockwise battery cover until the battery cover on the arrow and "lock" sign on a straight line. Remark: B.T Pedometer must be in the awake state, otherwise, click "save" only can store your information in the APP, Until the nextSuccessful sync to synchronize your information on your P118. - Now, you can use the APP to track your movements. Remark: B.T Pedometer must be in the awake state, otherwise, click "save" only can store your information in the APP, Until the nextSuccessful sync to synchronize your information on your P118. Remark: Android bluetooth devices must be in state of opening.If you do not open, the APP will reminder to open bluetooth device.Android device did not open the bluetooth device, operating APP may cause APP automatically exit. Note II Galaxy S5 Android 4.3 Note III Android 4.3 Nexus4/Nexus7 Android 4.3 Google G a s o l i n e A l c o h o l A c e t o n e To save battery, Pedometer will enter into sleep mode if there is no operation for a while. It can be showed by 4 situations as follows: - Once paried successful for first time, B.T Pedometer will enter into sleep mode after 30 minutes no operation - If there is any data in pedometer, B.T Pedometer will enter into sleep mode after 12 minutes no operation. - If there is no data stored in pedometer, B.T Pedometer will enter into sleep mode after 20s no operation. - After synchronizing data wit…

Text truncated - open the document above for the full version.

1 Photographs - EUT Constructional Details Test Model No.: P118 Dongle: U010

1 Photographs - EUT Constructional Details Test Model No.: P118 Dongle: U010

SGS-CSTC Standards Technical Services Co., Ltd. No. 1 W orkshop, M-10, Middle section, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.: SZEM140700367602 Page: 1 of 6 Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1 Cover page SAR Evaluation Report Application No.: SZEM1407003676RF Applicant: Million concept electronic (shenzhen) CO., LTD Manufacturer: Million concept electronic (shenzhen) CO., LTD Factory: Million concept electronic (shenzhen) CO., LTD Product Name: Pedometer watch Model No.(EUT): P118 Trade Mark: Isport FCC ID: OVJP118 Standards: 47 CFR Part 1.1307(2013) 47 CFR Part 2.1093 (2013) KDB447498D01 General RF Exposure Guidance v05 Date of Receipt: 2014-07-16 Date of Test: 2014-07-18 to 2014-08-05 Date of Issue: 2014-08-12 Test Result : PASS* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Report No.: SZEM140700367602 Page: 2 of 6 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 2 Version Revision Record Version Chapter Date Modifier Remark 00 2014-08-12 Original Authorized for issue by: Tested By 2014-08-05 (Chris Zhong) /Project Engineer Date Prepared By 2014-08-12 (Hedy Wen) /Clerk Date Checked By 2014-08-13 (Owen Zhou) /Reviewer Date SGS-CSTC Standards Technical Services Co., Ltd. Report No.: SZEM140700367602 Page: 3 of 6 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 3 Contents Page 1 COVER PAGE ..........…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Ltd. No. 1 W orkshop, M-10, Middle section, Science & Technology Park, Nanshan District, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 Email: [email protected] Report No.: SZEM140700367601 Page: 1 of 48 Authorized Signature: Jack Zhang EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 1 Cover page FCC REPORT Application No: SZEM1407003676RF Applicant: Million concept electronic (shenzhen) CO., LTD Manufacturer: Million concept electronic (shenzhen) CO., LTD Factory: Million concept electronic (shenzhen) CO., LTD Product Name: Pedometer watch Model No.(EUT): P118 Trade Mark: Isport FCC ID: OVJP118 Standards: 47 CFR Part 15, Subpart C (2013) Date of Receipt: 2014-07-16 Date of Test: 2014-07-18 to 2014-08-05 Date of Issue: 2014-08-12 Test Result: PASS * * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Ltd. Report No.: SZEM140700367601 Page: 2 of 48 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 2 Version Revision Record Version Chapter Date Modifier Remark 00 2014-08-12 Original Authorized for issue by: Tested By 2014-08-05 (Chris Zhong) /Project Engineer Date Prepared By 2014-08-12 (Hedy Wen) /Clerk Date Checked By 2014-08-13 (Owen Zhou) /Reviewer Date SGS-CSTC Standards Technical Services Ltd. Report No.: SZEM140700367601 Page: 3 of 48 “This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only.” 3 Test Summary Test Item Test Requirement Test method Result Antenna Requirement 47 CFR Part 15, Subpart C Section 15.203/15.24…

Text truncated - open the document above for the full version.

1 Photographs - EUT Test Setup Test Model No.: P118 1.1 Radiated Emission 1.2 Radiated Spurious Emission