OXGZW112Motion Sensor

FCC/IC Motion Sensor ZW112 Motion Sensor Show Home Products warrants this product to be free from manufacturing defects for a period of two years from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this product. This warranty is in lieu of all other warranties, expressed or implied. Some states do not allow limitations on how long an implied warranty lasts or permit the exclusion or limitation of incidental or consequential damage, so the above limitations may not apply to you. This warranty gives you specific rights, and you may also have other rights which vary from state to state. if the unit should prove defective within the warranty period. RISK OF FIRE RISK OF ELECTRICAL SHOCK RISK OF BURNS CONTROLLING APPLIANCES: EXERCISE EXTREME CAUTION WHEN USING Z-WAVE DEVICES TO CONTROL APPLIANCES. OPERATION OF THE Z-WAVE DEVICE MAY BE IN A DIFFERENT ROOM THAN THE CONTROLLED APPLIANCE, ALSO AN UNINTENTIONAL ACTIVATION MAY OCCUR IF THE WRONG BUTTON ON THE REMOTE IS PRESSED. Z-WAVE DEVICES MAY AUTOMATICALLY BE POWERED ON DUE TO TIMED EVENT PROGRAMMING. DEPENDING UPON THE APPLI- ANCE, THESE UNATTENDED OR UNINTENTIONAL OP- ERATIONS COULD POSSIBLY RESULT IN A HAZARDOUS CONDITION. FOR THESE REASONS, WE RECOMMEND DO NOT RETURN THIS PRODUCT TO THE STORE THE FOLLOWING: DO NOT USE Z-WAVE DEVICES TO CONTROL ELECTRIC HEATERS OR ANY OTHER APPLIANCES WHICH MAY PRES- ENT A HAZARDOUS CONDITION DUE TO UNATTENDED OR UNINTENTIONAL OR AUTOMATIC POWER ON CONTROL. WARNING WARRANTY Model:ZW112 Power supply: battery CR123A, 3V. Signal (Frequency): 908.42 MHz. Operating Range: Up to 100 feet line of sight Operating Temp.: 0°C~40°C Wireless Controller and the closest Z-Wave receiver module. Specifications subject to change without notice due to continuing product improvement SPECIFICATIONS Website www.ishowlights.com Federal Communications Commission (FCC) Statement FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may caus harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna.Increase the separation between the equipment and receiver.Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.Consult the dealer or an experienced radio/TV technician for help.This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. IC Caution: This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. DECLARATION DE CONFORMITE D'INDUSTRIE CANADA Ce périphérique a été testé et reconnu conforme aux limites spécifiées dans RSS-210. Son utilisation est soumise aux deux conditions suivantes : (1) il ne doit pas provoquer d'interférences gênantes et (2) il doit tolérer les interférences re.ues, notamment cellessusceptibles d'en perturber le fonctionnement. Instruction . 1.Do not attempt to disassemble the Motion Sensor,unless described in the user’s manual. There are no user serviceable parts. 2.Handle with Care – Avoid striking or shaking.Improper use or storage could damage the Motion Sensor. Modifying or tampering the device or its internal components can cause a malfunction and void the Motion Sensor’s warranty. 3.If you feel the Motion Sensor or any part of the Choice Alert system is not operating correctly or as described, please contact The Motion Sensor is designed to be used indoors or out. When mounted properly it can monitor large or open areas such as entrances, living rooms, family rooms, driveways, backyards, walkways, workshops,etc. When the Sensor detects motion, it will transmit a signal to the Control Center. The Zone selection and settings on the Control Center determine if an alarm or an alert sounds. 1.The Motion Sensor consists of 2 parts – The Sensor(Transmitter) and the wall mount. Before installing,remove the screw from the battery door on the back of the Sensor. You’ll need to attach the battery leads to CR123A 3V battery;Take care to note the polarity markings. Replace the battery cover and secure screw. battery in the Motion Sensor can last up to 9 months. Preparing the Motion Sensor for Installation Detection pattern: 100degree 7x7M at 25°C Top view Side View Important safeguards Package content Motion Sensor with mounting bracket - 1pcs Screw - 2pcs Plastic anchors - 2pcs Ball-head joint - 1pcs Low Battery Indicator The Control Center continuously monitors all the Sensors. If the Control Center does not receive a signal from any Sensor it will begin rapidly flashing the Zone LED indi…

Text truncated - open the document above for the full version.

SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 5.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Project and Product Certification Representative Authorization Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Revised wording (obsolete) 1.0 2.0 Sept–25-2007 Updated company template (obsolete) 2.0 3.0 Jan-31-2012 Updated letter information (obsolete) 3.0 4.0 May-23-2014 Added FCC ID field (current) 4.0 5.0 Sept 16 2014 SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 5.0 Willis Electric CO.,Ltd. 2015/5/07 To: SIEMIC, INC. 775 Montague Expressway, Milpitas, CA 95035 USA Dear Sir/Madam, Re: Product Certification Representative Authorization Letter We, WillisElectricCO.,Ltd. ,hereby authorize SIEMIC, Inc. to act as a Certification Body for certifying for the following project(s): Product description: Motion Sensor model name: ZW112 FCC ID: OXGZW112 Sincerely, Client’s signature Client’s name / title : Grace Dai / Safety Enginner Contact information / address: No.504-1, Chuang-Hua Road, Sec.4 Hsin Chu 300, Taiwan

SCS-F19: Confidentiality Request Letter Page 1 of 2 Rev 4.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Confidentiality Request Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Adding CFR 2.459 (obsolete) 1.0 2.0 August – 11 - 2008 Updated company template & Added text box (obsolete) 2.0 3.0 Jan-31-2012 Added IC confidentiality letter form (current) 3.0 4.0 March-26-2015 SCS-F19: Confidentiality Request Letter Page 2 of 2 Rev 4.0 Willis Electric CO.,Ltd. 2015/5/07 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Subject: Permanent Confidentiality Request for FCC ID: OXGZW112 We hereby request confidential treatment of information accompanying this application as outlined below: - e.g. Block Diagram - e.g. Schematics - e.g. Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Client’s signature Client’s name / title : Grace Dai / Enginner Contact information / address: No.504-1, Chuang-Hua Road, Sec.4 Hsin Chu 300, Taiwan

DongGuan Precise Testing Service Co.,Ltd. Report No.: PTS 15030580022F APPENDIX-PHOTOGRAPHS OF EUT CONSTRUCTIONAL DETAILS Photo 1 Photo 2 DongGuan Precise Testing Service Co.,Ltd. Report No.: PTS 15030580022F Photo 3 Photo 4 DongGuan Precise Testing Service Co.,Ltd. Report No.: PTS 15030580022F Photo 5 Photo 6

DongGuan Precise Testing Service Co.,Ltd. Report No.: PTS 15030580022F Photo 7 Photo 8 ANT DongGuan Precise Testing Service Co.,Ltd. Report No.: PTS 15030580022F Photo 10 Photo 9

FCC RADIO TEST REPORT FCC ID: OXGZW112 Product Name: Motion Sensor Trademark: Show Home Model Number: ZW112 Prepared For : Willis Electric CO.,Ltd. Address : No.504-1,Chung-Hua Road, Sec.4, Hsin Chu,300 Taiwan Prepared By : DongGuan Precise Testing Service Co.,Ltd. Address : Building D, Baoding Technology Park, Guangming Road 2, Guangming Community, Dongcheng District, Dongguan, Guangdong, China Test Date: May 10 – May 20, 2015 Date of Report : May 20, 2015 Report No.: PTS 15030580022F Page 2 of 28 Report No.: PTS15030580022F VERIFICATION OF COMPLIANCE Applicant: Willis Electric CO.,Ltd. Address No.504-1,Chung-Hua Road, Sec.4, Hsin Chu,300 Taiwan Manufacturer Name: Kupoint(DongGuan)Electric Co.,Ltd Address: Huai De Village, HumenTown, Dong Guan, Guang Dong, China Product Description: Motion Sensor Brand Name: Show Home Model Name: ZW112 Model difference: N/A Test procedure ANSI C63.10:2013 Standards FCC PART15.249 Prepared by : Jones Song /Assistant Reviewer : David liu /Supervisor Approved & Authorized Signer : Jacky Ou/Manager Page 3 of 28 Report No.: PTS15030580022F Table of Contents Page 1 . SUMMARY OF TEST RESULTS 5 1.1 TEST FACILITY 6 1.2 MEASUREMENT UNCERTAINTY 6 2 . GENERAL INFORMATION 7 2.1 GENERAL DESCRIPTION OF EUT 7 2.2 DESCRIPTION OF TEST MODES 8 2.3 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 9 2.4 DESCRIPTION OF SUPPORT UNITS(CONDUCTED MODE) 10 2.5 EQUIPMENTS LIST FOR ALL TEST ITEMS 11 FOR RADIATED EMISSION TEST (BELOW 1GHZ) 11 FOR RADIATED EMISSION TEST (1GHZ ABOVE) 11 3 . TEST RESULT 13 3.1 ANTENNA REQUIREMENT 13 3.1.1 STANDARD REQUIREMENT 13 3.1.2 EUT ANTENNA 13 3.2 CONDUCTED EMISSION MEASUREMENT 14 3.2.1 POWER LINE CONDUCTED EMISSION LIMITS 14 3.2.2 TEST PROCEDURE 15 3.2.3 DEVIATION FROM TEST STANDARD 15 3.2.4 TEST SETUP 15 3.2.5 TEST RESULT 16 3.3 RADIATED EMISSION MEASUREMENT 17 3.3.1 RADIATED EMISSION LIMITS 17 3.3.2 TEST PROCEDURE 18 3.3.3 DEVIATION FROM TEST STANDARD 18 3.3.4 TEST SETUP 19 3.3.5 TEST RESULTS (BLOW 30MHZ) 21 3.3.6 TEST RESULTS (BETWEEN 30 – 1000 MHZ) 22 3.3.7 TEST RESULTS (ABOVE 1000 MHZ) 25 4 . 20DB AND 99 % BANDWIDTH TEST 27 4.1 TEST PROCEDURE 27 4.2 DEVIATION FROM STANDARD 27 4.3 TEST SETUP 27 4.4 TEST RESULTS 28 Page 4 of 28 Report No.: PTS15030580022F Table of Contents Page APPENDIX-PHOTOGRAPHS OF EUT CONSTRUCTIONAL DETAILS Page 5 of 28 Report No.: PTS15030580022F 1. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: FCC Part15, Subpart C (15.249) Standard Section Test Item Judgment Remark 15.207 Conducted Emission N/A 15.203 Antenna Requirement Pass 15.249(a)&(d)&15.209Radiated Spurious Emission Pass 15.215 20 DB Bandwidth Pass 15.249(d)&15.209 Band Edge Emission Pass 15.249(a) Fundamental Measurement Pass Page 6 of 28 Report No.: PTS15030580022F 1.1 TEST FACILITY FCC Registration No.: 371540, IC Registration No.: 12191A-1 Dongguan Precise Testing Service Co., Ltd. Add.: Building D,Baoding Technology Park,Guangming Road2,Dongcheng District, Dongguan, Guangdong, China 1.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U，where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2，providing a level of confidence of approximately 95 %。 No. Item Uncertainty 1 Conducted Emission Test ±1.38dB 2 RF power,conducted ±0.16dB 3 Spurious emissions,conducted ±0.21dB 4 All emissions,radiated(<1G) ±4.68dB 5 All emissions,radiated(>1G) ±4.89dB 6 Temperature ±0.5°C 7 Humidity ±2% Page 7 of 28 Report No.: PTS15030580022F 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF EUT Equipment Motion Sensor Trade Name Show Home Model Name ZW112 Serial Model N/A Model Difference N/A Product Description The EUT is a Motion Senso r Operation Frequency: 908.42MHz Modulation Type: FSK Channel number 1 channel Antenna Designation: PCB antenna Antenna Gain(Peak) -2.1dBi Max. PK field strength 84.67 dBuV/m Based on the application, features, or specification exhibited in User's Manual, the EUT is considered as an ITE/Computing Device. More details of EUT technical specification, please refer to the User's Manual. Power Supply DC 3V HVIN ZW112 FVIN F_smart receptacle V1 Note: 1. For a more detailed features description, please refer to the manufacturer’s specifications or the User's Manual. Page 8 of 28 Report No.: PTS15030580022F 2.2 DESCRIPTION OF TEST MODES To investigate the maximum EMI emission characteristics generates from EUT, the test system was pre-scanning tested base on the consideration of following EUT operation mode or test configuration mode which possible have effect on EMI emission level. Each of these EUT operation mode(s) or test configuration mode(s) mentioned above was evaluated respectively. Pretest Mode Description Mode 1 TX For Conducted Emission Final Test Mode Description Mode 1 TX For Radiated Emission Final Test Mode Description Mode 1 TX Note: For the TX mode, the EUT is configured as the continuously transmitting mode. Page 9 of 28 Report No.: PTS15030580022F 2.3 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED E-1 EUT AC Page 10 of 28 Report No.: PTS15030580022F 2.4 DESCRIPTION OF SUPPORT UNITS(CONDUCTED MODE) The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. Item Equipment Mfr/Brand Model/Type No. Series No. Note E-1 Motion Sensor Show Home ZW112 N/A EUT Item Shielded Type Ferrite Core Length Note Note: (1) The support equipment was authorized by Declaration of Confirmation. (2) For detachable type I/O cable should be specified the length in cm in『Length』column. Page 11 of 28 Report No.: PTS15030580022F 2.5 EQUIPMENTS LIST FOR ALL TEST ITEMS FOR RADIATED EMISSION TEST (BELOW 1GHZ) Name of Equipment Manufacturer Model Serial No. Last Cal. Next Cal. EMI Test Receiver Rohde & SchwarzESCI 101417 July 4, 2014 July 3, 2015 Trilog Broadband Antenna (25M-1GHz) SCHWARZBECK VULB91…

Text truncated - open the document above for the full version.

APPENDIX-PHOTOGRAPHS OF EUT CONSTRUCTIONAL DETAILS