P4GTVEE26TX Wireless Speaker System

2 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance withthe manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding- type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third groundingprong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Unplug this apparatus during lightning storms or when unused for long periods of time. IMPORTANT SAFETY INSTRUCTIONS 13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, suchas power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been This class B digital apparatus complies with Canadian ICES-003.Cet appareil numérique de classe B est conforme á la norme NMB-003 du Canada. exposed to rain or moisture, does not operate normally, or has been dropped. 14. Maintain a minimum distance of 2" (50mm) around the front, rear, and sides of the apparatus for sufficient ventilation. The ventilation should not be impeded by covering the ventilation openings or placing on or around the apparatus items such as newspapers, table-cloths, curtains, etc. 15. No open flame sources, such as lighted candles, should be placed on the apparatus. 16. The apparatus shall not be exposed to dripping or splashing. 17. Either the power inlet connector on the rear of the apparatus or the power plug at the wall must remain accessible, to be able to disconnect power from the apparatus. 18.19. To completely disconnect this apparatus from the AC Mains, disconnect the power supply cord plug from the AC receptacle. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart or rack is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 20. CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. 21. WARNING: Only use attachments/accessories specified or provided by the manufacturer 22. WARNING Please refer the information on exterior bottom enclosure for electrical and safety information before installing or operating the apparatus. 25. When not in use and during movement, please take care of the power cordset, e.g. tie up the power cordset with cable tie or something like that. It shall be free from sharp edges and the like that can cause abrasion of the power cordset. When put into use again, please make sure the power cordset being not damaged, If any damages found, please look for the service person to replace the power cordset specified by the manufacturer or have the same characteristics as the original one. 26. Warning: To reduce the risk of electric shock, do not remove cover (or back) as there are no user-serviceable parts inside. Refer servicing to qualified personnel. No objects filled with liquids, such as vases, shall be placed on the apparatus. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC American Users: Rules. These limits are designed to provide reasonable protectionagainst harmful interference in a residential installation. This equip-ment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. ’ Caution: Unauthorized changes or modifications to the receiver could void the user s authority to operate the equipment. This symbol found on the apparatus indicates hazards arising from dangerous voltages.This symbol found on the apparatus indicates the usershould read all safety statements found in the user manual.This symbol found on the apparatus indicates double insulation.Warning! To reduce the risk of fire or electrical shock, do not expose this apparatus to rain or moisture. Canadian Users: RLAN - Radio Local Area Network EquipmentThis equipment may only be used indoors in FR.This equipment may only be used in one’s own premises in IT.This equipment is for private use only in LUOperation is not allowed within a radius of 20 km from the centre of Ny-Ålesund in NO.Hereby, Boston Acoustics, Inc. 7 Constitution Way, Woburn, MA 01801         essential requirements and other relevant provisions of Directive !#$ %& ' &#& %*'+#4 %6 obtained from:Oliver KrieteBoston Acoustics, D…

Text truncated - open the document above for the full version.

29 IMPORTANTI ISTRUZIONI DI SICUREZZA ’ | AT CZ FI IS LT PT SE FR BE DK DE IE MT SK CH IT EE GR LV NL SI TR LU CY HU PL ES GB NO Prodotto dietro licenza di Dolby Laboratories. Dolby e il simbolo della doppia D sono marchi di fabbrica di Dolby Laboratories. 23. Q uando il prodotto non è in uso o quando si è in movimento, prestare attenzione al set di cavi di alimentazione, ad esempio fissando i cavi servendosi di un fermacavo o di qualcosa di simile. Deve essere mantenuto lontano da bordi taglienti e simili in grado di causare abrasioni a livello del cavo stesso. Al momento di riprendere l ' utilizzo dell ' apparecchio, assicurarsi che il cavo di alimentazione non sia danneggiato. Q ualora venissero individuati danni, contattare un tecnico affinché sostituisca il cavo di alimentazione con uno specificato dal produttore o avente caratteristiche pari a quello originale. 24. Avvertenza: per ridurre il rischio di scossa elettrica, non rimuovere il coperchio (o il retro dell ' apparecchio) in quanto all ' interno non sono presenti parti riparabili dall ' utente. Per l ' assistenza tecnica, rivolgersi a personale qualificato. Utilizzatori americani: Nota bene: In base alle prove su di esso eseguite, si è determinata la conformit à di questo apparecchio ai limiti relativi ai dispositivi digitali di Classe B, secondo la Parte 15 delle norme FCC. Tali limiti sono stati concepiti per garantire un ' adeguata protezione contro le interferenze pericolose in un impianto residenziale. Q uesto apparecchio genera, utilizza e pu ò irradiare energia a radiofrequenza e, se non installato e utilizzato secondo le istruzioni, pu ò causare interferenze dannose per le comunica- zioni radio. Tuttavia, non esiste alcuna garanzia che, in una specifica installazione, non si verificheranno interferenze. Se questo apparecchio causasse interferenze dannose per la ricezione dei segnali radio o televisivi, determinabili spegnendolo e riaccendendolo, si consiglia di tentare di rimediare all ' interferenza con uno o pi ù dei seguenti metodi: Modificare l ' orientamento dell ' antenna ricevente o spostarla Aumentare la distanza tra l ' apparecchio ed il ricevitore. Collegare l ' apparecchio ad una presa inserita in un circuito diverso da quello a cui è collegato il ricevitore. Per qualsiasi problema, rivolgersi al rivenditore o ad un tecnico radio/TV qualificato. Attenzione: eventuali cambiamenti o modifiche non autorizzati apportati al ricevitore potrebbero rendere nulla l ' autorit à da parte dell ' utente di utilizzare l ' apparecchio. Utilizzatori canadesi: Q uesto apparecchio digitale di Classe B è conforme alle norme canadesi ICES-003. Utilizzatori europei: RLAN - Radio Local Area Network Equipment Q uesta attrezzatura pu ò essere utilizzata unicamente all ' interno in FR. Q uesta attrezzatura pu ò essere utilizzata unicamente nelle proprie propriet à in IT. Q uesta attrezzatura è indicata unicamente per un uso privato in LU. L ' utilizzo non è consentito entro un raggio di 20 km dal centro di Ny-Ålesund in NO. Con il presente documento, Boston Acoustics, Inc. 7 Constitution Way, Woburn, MA 01801 USA, dichiara che il TVee 26 è conforme con i requisiti essenziali e le altre disposizioni specifiche della Direttiva 1999/5/CE. Una copia della Dichiarazione di Conformit à (DOC) pu ò essere richiesta a: Oliver Kriete Boston Acoustics, Division of D&M Europe B.V. Beemdstraat 11 5653 MA Eindhoven Paesi Bassi ATTEN Z IONE PERICOLO DI SCOSSA ELETTRICA. NON APRIRE.            Q uesto simbolo riportato sull ' apparecchio indica pericoli derivanti da voltaggi pericolosi. Q uesto simbolo riportato sull ' apparecchio indica l ' obbligo da parte dell ' utente di leggere tutte le istruzioni di sicurezza illustrate nel manuale per l ' uso. Q uesto simbolo riportato sull ' apparecchio indica la presenza di un doppio isolamento. Avvertenza!Per ridurre il rischio di incendio o di scossa elettrica, non esporre l ' apparecchio alla pioggia o all ' umidit à . 1. Leggere le presenti istruzioni. 2. Conservare le presenti istruzioni. 3. Rispettare tutte le avvertenze. 4. Seguire tutte le istruzioni. 5. Non utilizzare l ' apparecchio vicino all ' acqua. 6. Pulire unicamente con un panno asciutto. 7. Non ostruire le aperture di ventilazione. Installare il prodotto nel rispetto delle istruzioni del produttore. 8. Non installare il prodotto nei pressi di sorgenti di calore quali radiatori, caloriferi, stufe o altri dispositivi (inclusi gli amplificatori) che generano calore. 9. Non aggirare la sicurezza offerta dalla spina polarizzata o con messa a terra. Una spina polarizzata presenta due lame, di cui una è pi ù larga dell ' altra. Una spina con messa a terra presenta due lame ed un terzo polo deputato alla messa a terra. La lama ampia o il terzo polo sono forniti per la sicurezza dell ' utilizzatore. Se la spina in dotazione non è adatta alla propria presa, rivolgersi ad un elettricista per richiedere la sostituzione della presa obsoleta. 10. Evitare che il cavo di alimentazione venga calpestato o compresso, in particolare in corrispondenza delle spine, dei connettori femmina e dei punti in cui escono dall ' apparecchio. 11. Servirsi unicamente di accessori specificati dal produttore. 12. Scollegare l ' apparecchio durante i temporali o quando non viene utilizzato per lunghi periodi di tempo. 13. Per qualsiasi lavoro di manutenzione, rivolgersi a personale di assistenza qualificato. L ' assistenza tecnica è necessaria nel caso in cui l ' apparecchio sia danneggiato, ad esempio per problemi a livello del cavo di alimentazi- one o della spina, in caso di rovesciamento di liquidi o di caduta di oggetti nell ' apparecchio, o qualora questo sia stato esposto alla pioggia o all ' umidit à , presenti anomalie di funzionamento o sia caduto. 14. Rispettare una distanza minima di 50 mm dalle parti anteriore, posteriore e laterali dell ' apparecchio per garantire una ventilazione sufficiente. La ventilazione non dev…

Text truncated - open the document above for the full version.

Neutron Engineering Inc. Project No.: 1206C140 Page 2 of 17 1206C140 Neutron Engineering Inc. Project No.: 1206C140 Page 3 of 17 1206C140 1206C140 Neutron Engineering Inc. Project No.: 1206C140 Page 3 of 17 1206C140 1206C140 Neutron Engineering Inc. Project No.: 1206C140 Page 4 of 17 1206C140 1206C140 Neutron Engineering Inc. Project No.: 1206C140 Page 4 of 17 1206C140 1206C140 Neutron Engineering Inc. Project No.: 1206C140 Page 5 of 17 1206C140 1206C140 Neutron Engineering Inc. Project No.: 1206C140 Page 5 of 17 1206C140 1206C140 Neutron Engineering Inc. Project No.: 1206C140 Page 6 of 17 1206C140 1206C140 Neutron Engineering Inc. Project No.: 1206C140 Page 6 of 17 1206C140 1206C140 Neutron Engineering Inc. Project No.: 1206C140 Page 7 of 17 1206C140

Neutron Engineering Inc. Project No.: 1206C140 Page 8 of 17 1206C140 1206C140 Neutron Engineering Inc. Project No.: 1206C140 Page 8 of 17 1206C140 1206C140 Neutron Engineering Inc. Project No.: 1206C140 Page 9 of 17 1206C140 1206C140 Neutron Engineering Inc. Project No.: 1206C140 Page 9 of 17 1206C140 1206C140 Neutron Engineering Inc. Project No.: 1206C140 Page 10 of 17 1206C140 1206C140 Neutron Engineering Inc. Project No.: 1206C140 Page 10 of 17 1206C140 1206C140 Neutron Engineering Inc. Project No.: 1206C140 Page 11 of 17 1206C140 1206C140 Neutron Engineering Inc. Project No.: 1206C140 Page 11 of 17 1206C140 1206C140 Neutron Engineering Inc. Project No.: 1206C140 Page 12 of 17 1206C140 1206C140 Neutron Engineering Inc. Project No.: 1206C140 Page 12 of 17 1206C140 1206C140 Neutron Engineering Inc. Project No.: 1206C140 Page 13 of 17 1206C140 1206C140 Neutron Engineering Inc. Project No.: 1206C140 Page 13 of 17 1206C140 1206C140 Neutron Engineering Inc. Project No.: 1206C140 Page 14 of 17 1206C140 1206C140 Neutron Engineering Inc. Project No.: 1206C140 Page 14 of 17 1206C140 1206C140 Neutron Engineering Inc. Project No.: 1206C140 Page 15 of 17 1206C140 1206C140 Neutron Engineering Inc. Project No.: 1206C140 Page 15 of 17 1206C140 1206C140 Neutron Engineering Inc. Project No.: 1206C140 Page 16 of 17 1206C140 1206C140 Neutron Engineering Inc. Project No.: 1206C140 Page 16 of 17 1206C140 1206C140 Neutron Engineering Inc. Project No.: 1206C140 Page 17 of 17 1206C140 1206C140 Neutron Engineering Inc. Project No.: 1206C140 Page 17 of 17 1206C140 1206C140

Neutron Engineering Inc. FCC RF EXPOSURE REPORT FCC ID: P4GTVEE26 Project No. : 1206C140 Equipment : TX Wireless Speaker System Model : Tvee®26 Applicant : Boston Acoustics INC. Address : 7 Constitution Way, Woburn, Massachusetts 01801, USA According: : FCC Guidelines for Human Exposure IEEE C95.1 Neutron Engineering Inc. No.3, Jinshagang 1st Road, ShiXia, Dalang Town, Dong Guan, China. TEL : (0769) 8318-3000 FAX : (0769) 8319-6000 Neutron Engineering Inc. MPE CALCULATION METHOD: Calculation Method of RF Safety Distance: where: S = power density P = power input to the antenna G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna Ant. Brand name Model Name Antenna TypeConnector Gain (dBi) 1 N/A N/A PCB AntennaN/A 3.3 TEST RESULTS EUT： TX Wireless Speaker System Model Name ： Tvee®26 Temperature： 25 °C Relative Humidity： 58 % Pressure： 1009 hPa Test Voltage ： AC 120V/60Hz Test Mode ： CH01/ CH10 /CH18 -5Mbps Antenna Gain (dBi) Antenna Gain (numeric) Peak Output Power (dBm) Peak Output Power (mW) Power Density (S) (mW/cm 2 ) Limit of Power Density (S) (mW/cm 2 ) Te s t Result 3.3 2.1380 1.70 1.4791 0.000629 1 Complies 3.3 2.1380 1.73 1.4894 0.000634 1 Complies 3.3 2.1380 1.85 1.5311 0.000652 1 Complies

Neutron Engineering Inc. Report No.: NEI-FICP-1-1206C140 Page 1 of 72 FCC/IC Radio Test Report FCC ID: P4GTVEE26 IC: 10104A-TVEE26 This report concerns (check one) : Original Grant Class II Change Issued Date : Jul. 13, 2012 Project No. : 1206C140 Equipment : TX Wireless Speaker System Model Name : Tvee®26 Applicant : Boston Acoustics INC. Address : 7 Constitution Way,Woburn,Massachusetts 01801,USA Manufacturer : Boston Acoustics INC. Address : 7 Constitution Way,Woburn,Massachusetts 01801,USA Tested by: Neutron Engineering Inc. EMC Laboratory Date of Receipt: Jun. 19, 2012 Date of Test: Jun. 19, 2012 ~ Jul. 12, 2012 Testing Engineer : (David Mao) Technical Manager : (Leo Hung) Authorized Signatory : (Steven Lu) Neutron Engineering Inc. No.3,Jinshagang 1st Road, ShiXia, Dalang Town, Dong Guan, China. TEL : (0769) 8318-3000 FAX : (0769) 8319-6000 Neutron Engineering Inc. Report No.: NEI-FICP-1-1206C140 Page 2 of 72 Declaration Neutron represents to the client that testing is done in accordance with standard procedures as applicable and that test instruments used has been calibrated with the standards traceable to National Measurement Laboratory (NML) of CHINA, or National Institute of Standards and Technology (NIST) of U.S.A. Neutron's reports apply only to the specific samples tested under conditions. It is manufacture’s responsibility to ensure that additional production units of this model are manufactured with the identical electrical and mechanical components. Neutron shall have no liability for any declarations, inferences o r generalizations drawn by the client or others from Neutron issued reports. Neutron’s reports must not be used by the client to claim product endorsement by the authorities or any agency of the Government. This report is the confidential property of the client. As a mutual protection to the clients, the public and Neutron-self, extracts from the test report shall not be reproduced except in full with Neutron’s authorized written approval. Neutron’s laboratory quality assurance procedures are in compliance with the ISO Guide 17025 requirements, and accredited by the conformity assessment authorities listed in this test report. Limitation For the use of the authority's logo is limited unless the Test Standard(s)/Scope(s)/Item(s) mentioned in this test report is (are) included in the conformity assessment authorities acceptance respective. Neutron Engineering Inc. Report No.: NEI-FICP-1-1206C140 Page 3 of 72 Table of Contents Page 1 . CERTIFICATION 6 2 . SUMMARY OF TEST RESULTS 7 2.1 TEST FACILITY 8 2.2 MEASUREMENT UNCERTAINTY 8 3 . GENERAL INFORMATION 9 3.1 GENERAL DESCRIPTION OF EUT 9 3.2 DESCRIPTION OF TEST MODES 11 3.3 TABLE OF PARAMETERS OF TEXT SOFTWARE SETTING 11 3.4 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 12 3.5 DESCRIPTION OF SUPPORT UNITS 13 4 . EMC EMISSION TEST 14 4.1 CONDUCTED EMISSION MEASUREMENT 14 4.1.1 POWER LINE CONDUCTED EMISSION LIMITS 14 4.1.2 MEASUREMENT INSTRUMENTS LIST AND SETTING 14 4.1.3 TEST PROCEDURE 15 4.1.4 DEVIATION FROM TEST STANDARD 15 4.1.5 TEST SETUP 15 4.1.6 EUT OPERATING CONDITIONS 15 4.1.7 TEST RESULTS 16 4.2 RADIATED EMISSION MEASUREMENT 22 4.2.1 RADIATED EMISSION LIMITS 22 4.2.2 MEASUREMENT INSTRUMENTS LIST ANS SETTING 23 4.2.3 TEST PROCEDURE 24 4.2.4 DEVIATION FROM TEST STANDARD 24 4.2.5 TEST SETUP 25 4.2.6 EUT OPERATING CONDITIONS 26 4.2.7 TEST RESULTS (BETWEEN30 – 1000 MHZ) 27 4.2.8 TEST RESULTS (ABOVE 1000 MHZ) 31 5 . NUMBER OF HOPPING CHANNEL 49 5.1 APPLIED PROCEDURES / LIMIT 49 5.1.1 MEASUREMENT INSTRUMENTS LIST AND SETTING 49 5.1.2 TEST PROCEDURE 49 5.1.3 DEVIATION FROM STANDARD 49 5.1.4 TEST SETUP 49 5.1.5 EUT OPERATION CONDITIONS 49 5.1.6 TEST RESULTS 50 6 . AVERAGE TIME OF OCCUPANCY 51 Neutron Engineering Inc. Report No.: NEI-FICP-1-1206C140 Page 4 of 72 Table of Contents Page 6.1 APPLIED PROCEDURES / LIMIT 51 6.1.1 MEASUREMENT INSTRUMENTS LIST 51 6.1.2 TEST PROCEDURE 51 6.1.3 DEVIATION FROM STANDARD 51 6.1.4 TEST SETUP 52 6.1.5 EUT OPERATION CONDITIONS 52 6.1.6 TEST RESULTS 53 7 . HOPPING CHANNEL SEPARATION MEASUREMENT 55 7.1 APPLIED PROCEDURES / LIMIT 55 7.1.1 MEASUREMENT INSTRUMENTS LIST AND SETTING 55 7.1.2 TEST PROCEDURE 55 7.1.3 DEVIATION FROM STANDARD 55 7.1.4 TEST SETUP 55 7.1.5 EUT OPERATION CONDITIONS 55 7.1.6 TEST RESULTS 56 8 . BANDWIDTH TEST 58 8.1 APPLIED PROCEDURES / LIMIT 58 8.1.1 MEASUREMENT INSTRUMENTS LIST AND SETTING 58 8.1.2 TEST PROCEDURE 58 8.1.3 DEVIATION FROM STANDARD 58 8.1.4 TEST SETUP 58 8.1.5 EUT OPERATION CONDITIONS 58 8.1.6 TEST RESULTS 59 9 . PEAK OUTPUT POWER TEST 61 9.1 APPLIED PROCEDURES / LIMIT 61 9.1.1 MEASUREMENT INSTRUMENTS LIST AND SETTING 61 9.1.2 TEST PROCEDURE 61 9.1.3 DEVIATION FROM STANDARD 61 9.1.4 TEST SETUP 61 9.1.5 EUT OPERATION CONDITIONS 61 9.1.6 TEST RESULTS 62 10 . ANTENNA CONDUCTED SPURIOUS EMISSION 64 10.1 APPLIED PROCEDURES / LIMIT 64 10.1.1 MEASUREMENT INSTRUMENTS LIST AND SETTING 64 10.1.2 TEST PROCEDURE 64 10.1.3 DEVIATION FROM STANDARD 64 10.1.4 TEST SETUP 64 10.1.5 EUT OPERATION CONDITIONS 64 10.1.6 TEST RESULTS 65 Neutron Engineering Inc. Report No.: NEI-FICP-1-1206C140 Page 5 of 72 Table of Contents Page 11 . EUT TEST PHOTO 71 Neutron Engineering Inc. Report No.: NEI-FICP-1-1206C140 Page 6 of 72 1. CERTIFICATION E q u i p m e n t : TX Wireless Speaker System Brand Name : Boston® Model Name : Tvee®26 A p p l i c a n t : Boston Acoustics INC. F a c t o r y : Premium Loudspeakers (Huizhou) Co., Ltd A d d r e s s : Tymphany Industrial Area, Xin Lian Village, Xin Xu Tow, Hui Yang District, Hui Zhou City, Guang Dong Province, P.R.C China Date of Test : Jun. 19, 2012 ~ Jul. 12, 2012 T e s t I t e m : ENGINEERING SAMPLE Standards : FCC Part15, Subpart C(15.247) / ANSI C63.4 : 2009 / ANSI C63.10:2009 / FCC Public Notice DA 00-705, March 30, 2000. Canada RSS-210:2010 The above equipment has been tested and found compliance with the requirement of the relative standards by Neutron Engineering Inc. EMC Laboratory. The test data, data evaluation, and…

Text truncated - open the document above for the full version.

Neutron Engineering Inc. Report No.: NEI-FICP-1-1206C140 Page 71 of 72 11. EUT TEST PHOTO Conducted Measurement Photos Neutron Engineering Inc. Report No.: NEI-FICP-1-1206C140 Page 71 of 72 11. EUT TEST PHOTO Conducted Measurement Photos Neutron Engineering Inc. Report No.: NEI-FICP-1-1206C140 Page 72 of 72 Radiated Measurement Photos Neutron Engineering Inc. Report No.: NEI-FICP-1-1206C140 Page 72 of 72 Radiated Measurement Photos