P4L000MD101WIRELESS BLUETOOTH SPEAKER

MD1 6.Re-pairing: To touch the PAIR button on the control panel for re-pairing, meanwhile the indicator will flash, and there is voice prompt” Waiting for the pairing”. then you can pair the MD1 with your Mobile, the voice prompt 【pairing completed】after paired. 8.AUX input play: connect MD1 and Audio source with 3.5mm Audio Cable then touch the INPUT button on the control panel, the indicator will turn red and the unit will be connected to the AUX channel play. You can play music via 3.5mm from Mobile, Mp3, and PC. INPUT MADE IN CHINA Address : hongtu RD,Songxia lndustry Park,Songgang Nanhai District,Foshan, Guangdong Province,China Manufacturer:Foshan LANCHIYA Digital Technology Co., Ltd China SPECIFICATIONS Amplifier output power: left/right 1.5WX2 /3Ω Subwoofer 5WX1 /2Ω Amplifier input sensitivity: ≤500mV : ≤ % Amplifier SNR: ≥ 75dB Frequency response:65Hz~20KHz DC input: DC9V 2.5A Battery: 7.4V 2000mAh Battery time 6-10hours Battery charging time: 4-6hours Blue tooth range: 8-10M Bluetooth version: 2.1+EDR Support A2DP Distortion 1 5 6 9.Built-in battery use: when using the built-in battery to play music, the unit will manage the battery use automatically, when the power is low, the unit will decrease the volume to ensure the sound quality and longer play time, and voice prompt(NO battery please recharge) once in 1 minutes, the front indicator will be red and flash, When battery cannot support normal used unit will be power off after red indicator flash for 5 times. 6.Please use power adaptor which provide from Lanchiya to avoid damage your speaker. 7.Not work with NFC: please make sure the mobile has NFC function and turn it on. 8.The phone case may influence the NFC function, please remove if you cannot connect NFC as well. 9.Please recharge or user power adaptor when battery is low, for the device can work as well. 10.Please recharge the batter in every three months if long times no use. 11.The speaker has high capacity batter inside please avoid the heat, wet, do not disassemble the battery or put in into water or fire. 12.If you have problem with NFC, please check: 1)Make sure the mobile has NFC function, 2)Make sure the NFC and Bluetooth is ON 3)Make sure the NFC can activate the Bluetooth and audio in you mobile 4)Make sure the mobile is unlocked 5)Remove the phone case 6)Use the right part of NFC on your mobile 7)If the NFC found AMETHYST MD1 but can't connect, make sure MD1 is on and under Bluetooth mode NOTE * 1.The Bluetooth device can't find the speaker, the speaker may still connect with last Blue tooth device or another device are searching and connecting with speaker at same time. Now you need to operate as Step 6 to re-connect it 2. If you hear intermittent sound or no sound from speaker after connection Please check if the distance from you and speakers are in communication range (8-10M without barrier) 3.if you can not connect with speaker as well, please power it off for 3s then turn it on. 4.Don't let Opposite close to speaker when you use speaker phone function to avoid Echo 5.Please use default music player with your blue tooth device system like, iPod, Samsung player, Windows media player. As lots of third party music player does not support smooth song change function, to avoid “pu”sound. 7.TF card: Insert the TF card when MD1 is on, the Md1 will play music from TF card automatically, or you can press INPUT to select TF card, the front indicator will be orange, follow the step 4 to control the music playing. PAIR INPUT 10.Charging: the unit is with built-in battery, please use the supplied power adapter to charge it, the green indicator on the back of the unit will flash when charging. When the battery is fully-charged, the green indicator will stop flash MD1插卡版英文说明书MD1-G01-0 Switching Power Supply Model:GT-WAAU09000250-102 INPUT:100-240V~50/60Hz 0.8A OUTPUT:DC 9V 2500mA Genesis Science Technology Limited 1 1.MD1 machine 2. Power adapter 3.Audio cable 4 User manual . PACKAGE CONTENTS Brief Operation Introduction PROPERTY RIGHTS INFORMATION: The trademark amethyst lanchiya and all the developed products with this label are registered patents,and belong to Foshan LANCHIYA digitai Technology Co.,Ltd. Our company reservesall rights,and not allow reprinting.Other concerned trademarks all belong to their proprietors.As to the constant update and development of the products,our company reserves the right to change and rework our products without notice. WARING: To prevent any fire or electrical hazards, do not remove or dissemble any parts from this unit. Please ensure that you use a qualified technician to service it. • Do not expose the unit to rain, water or moisture • Do not place liquid on or close to unit • Do not place unit on or near an open fire such as candles or light • Keep away from heat and dust • Place unit on a stable and level platform • Do not place any items on top of unit • Do not use excessive force when pushing the unit buttons • Do not attempt to pull the power cord from a distance to shut the power Children and dispose in appointed place for battery • Secure all cords and connections and do not use pinched or defective one • Unplug the power cable if the unit is left unused for extended periods • Clean with a damp cloth only • • Blue tooth device can't be found: probably, the Speaker has been connected by other Blue tooth device. Press Pair button to search it again. If you still cannot find the speaker, please Turn Off the speaker for 5second then turn it on. • Blue tooth signal intermittently: the effective distance between speaker and Device is 10M, the signal will be intermittent if the distance more than 10M. • If there are more than 1 Speaker are switch on, the Bluetooth device will find more than 1 speaker, if you want to connect one of them please turn off the others • If your Bluetooth device on searching and find many other Bluetooth device, please wait for the searching finished and select Speaker to pair. The unit with Lithium Bat…

Text truncated - open the document above for the full version.

External Photos:

Internal Photos:

SGS-CSTC Standards Technical Services Co., Ltd. 19 8 Ke zhu Roa d, Scient ech Park, Guangzhou Economic & Technolo gical De velopment D istrict, Guangzhou, China 510663 Telephon e: +86 (0) 20 8 2155555 Fax: +86 (0) 20 820750 59 Email: ee. guangzh [email protected] Report No.: GZEM130900461301 Page: 1 of 72 FCC ID: P4L000MD101 Richard Li Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only 1 Cover Page TEST REPORT Application No.: GZEM1309004613AV Applicant: FOSHAN LANCHIYA DIGITAL TECHNOLOGY CO., LTD FCC ID: P4L000MD101 Product Name: Wireless Bluetooth speaker Product Description: Bluetooth speaker with 2.4 GHz as carrier Model No.: MD1 Trade mark: AMETHYST Standards: 47 CFR PART 15 Subpart C: 2012 section 15.247 Date of Receipt: 2013-10-31 Date of Test: 2013-10-31 to 2013-11-14 Date of Issue: 2013-11-15 Test Result : Pass* * In the configuration tested, the EUT detailed in this report complied with the standards specified above. Please refer to section 3 of this report for further detail. SGS-CSTC Standards Technical Services Co., Ltd. Report No.: GZEM130900461301 Page: 2 of 72 FCC ID: P4L000MD101 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 2 Version Revision Record Version Chapter Date Modifier Remark 00 2013-11-15 Original Authorized for issue by: Tested By 2013-10-31 to 2013-11-14 (Daniel He) /Signature Date Prepared By 2013-11-15 (Daniel He) /Signature Date Checked By 2013-11-15 (Storm Shu) /Reviewer Date SGS-CSTC Standards Technical Services Co., Ltd. Report No.: GZEM130900461301 Page: 3 of 72 FCC ID: P4L000MD101 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 3 Test Summary Test Test Requirement Test method Result Antenna Requirement FCC PART 15 C section 15.247 (c) and Section 15.203 FCC PART 15 C section 15.247 (c) and Section 15.203 PASS Occupied Bandwidth FCC PART 15 C section 15.247 (a)(1) ANSI C63.10: Clause 6.9.1 PASS Carrier Frequencies …

Text truncated - open the document above for the full version.

Setup Photos: 1.1 RADI ATE D SP URI OU S E 30 MHz to 1 GHz: Above 1 GHz: EM ISSIO N TE ST SETUP 1.2 CON DU CTED EM ISSI ON TEST SETUP